On which factor mechanical advantage of simple machine depend on? Please help me and perfect answer will be brainlest answer. ​

Answer:

we learned that an object that is vibrating is acted upon by a restoring force. The restoring force causes the vibrating object to slow down as it moves away from the equilibrium position and to speed up as it approaches the equilibrium position. It is this restoring force that is responsible for the vibration. So what forces act upon a pendulum bob? And what is the restoring force for a pendulum? There are two dominant forces acting upon a pendulum bob at all times during the course of its motion. There is the force of gravity that acts downward upon the bob. It results from the Earth's mass attracting the mass of the bob. And there is a tension force acting upward and towards the pivot point of the pendulum. The tension force results from the string pulling upon the bob of the pendulum. In our discussion, we will ignore the influence of air resistance - a third force that always opposes the motion of the bob as it swings to and fro. The air resistance force is relatively weak compared to the two dominant forces.

The gravity force is highly predictable; it is always in the same direction (down) and always of the same magnitude - mass*9.8 N/kg. The tension force is considerably less predictable. Both its direction and its magnitude change as the bob swings to and fro. The direction of the tension force is always towards the pivot point. So as the bob swings to the left of its equilibrium position, the tension force is at an angle - directed upwards and to the right. And as the bob swings to the right of its equilibrium position, the tension is directed upwards and to the left. The diagram below depicts the direction of these two forces at five different positions over the course of the pendulum's path.

that's what I know so far

Answer:

option a is correct

Explanation:

water ∠iron∠aluminium∠mercury

water density =1.0000

iron =7.487

aluminium=2.07

mercury=13.59

Answer:

Explanation:

Average rate = gallons / minutes

If 12.5gallons in 5mins

Xgallons in 1mins

12.5/5 = 2.5gallons per minute

Answer:

0 degrees Celsius is 273 degrees Kelvin. As both pressure and volume are proportional to absolute temperature, in order to double both you would need to quadruple the temperature. I.e. 273 X 4 = 1092 Kelvin = 819 Celsius

Explanation:

Answer: D

Explanation:

Given that a car travels from point A to B in 3 hours and returns back to point A in 5 hours. Points A and B are 150 miles apart along a straight highway.

From point A to B

The speed = distance / time

Where

Distance = 150 mile

Time = 3 hours

Substitute the values into the formula

Speed = 150/3 = 50 mile/ hours

From Point B to Point A

Distance = 150 miles

Time = 5 hours

Where speed = distance/ time

substitute all the parameters into the formula

Speed = 150/5 = 30 mph

Therefore, The car travels at 50 mph for the first half and 30 mph for the second half.

The correct answer is option D

Millimeters, centimeters, meters, kilometers, inches, feet, and miles are all examples of unit of length like: distance between two points  and displacement of any object.

Meter is  a Si unit of length whereas centimeter is CGS unit of length and  Feet is FPS unit of lengths. Another units are also useful in measuring lengths.

Learn more about units here:

https://brainly.com/question/12750330

#SPJ2

Answer:

HELLO BELOW IS THE ATTACHED DIAGRAM USED TO ANSWER YOUR QUESTION AS IT WAS MISSING

A) 1270⁰c

B) 65%

C) 1320⁰c

D)  62%

Explanation:

Nickel alloy composition : 50 wt% Ni - 50 wt%

initial temperature = 1200⁰c = 2190⁰F

A) The temperature at which the first liquid phase form

from the attached diagram the temperature at which the first liquid if formed is 1270⁰c ( at point 2 )

B ) The composition of this liquid phase ( THE FIRST LIQUID )

the composition is found at point 3

wt % of Nickel = 35%, wt% of copper = 100 - 35 = 65%

C ) The temperature at which the alloy melts completely

from the attached diagram the temperature = 1320⁰c ( point 4 )

D)  The composition of the last solid remaining prior to complete melting

this can be gotten at point 5 and calculated as

wt % of Ni = 62%

wt % of Cu = 100 - 62 = 38%

Answer:

a) Strings of guitar (being played)

b) Heart-beat in a healthy person

c) Motion of an apple falling from a tree

Explanation:

a) The motion of the string of a guitar being played is the only motion involving simple harmonic motion.

b) All the other motions are circular motion except the heart beat in a healthy person, which is periodic.

c) The motion of an apply falling from a tree is the only motion under the complete influence of gravity from the onset till the end.

Answer:

Explanation:

[tex]m =800kg\\v = 15\\\\K.E = \frac{1}{2}mv^2\\ K.E= \frac{1}{2} \times 800\times 15^2\\= 400 \times 225\\= 90000 joules\\= 90 kilojoules[/tex]

Answer:

1. Tienes 1 kg de fruta.

2. Queda por recorrer 1/4 km.

3. Ambos pesan lo mismo.

Explanation:

1. Tienes 1/2 kg y cuando te doy 1/4 te queda:

[tex] m = \frac{1}{2} - \frac{1}{4} = \frac{1}{4} [/tex]

Ahora cuando te doy 3/4 kg te queda en total:

[tex] m_{T} = \frac{1}{4} + \frac{3}{4} = 1 kg [/tex]

Por lo tanto, tienes 1 kg de fruta al final.

2. Si falta por recorrer la mitad de la mitad, tenemos:

[tex] d = \frac{1/2}{2} = \frac{1}{4} [/tex]

Entonces, queda por recorrer 1/4 km.

3. El peso (P) del hierro es:

[tex] P = m*g [/tex]    

[tex] P = (1 + 1/2)kg*9.81 m/s^{2} = 14.72 N [/tex]

Y el peso de la paja es:

[tex] P = 3/2 kg*9.81 m/s^{2} = 14.72 N [/tex]

Por lo tanto, ambos pesan lo mismo.

Espero que te sea de utilidad!

Answer:

The volume of the cylinder is [tex]653.71\ \text{cm}^3[/tex]

Explanation:

Given that,

The height of the cylinder is 13 cm

Radius of the cylinder is 4 cm

We need to find the volume of the cylinder. The formula that is used to find the volume of a cylinder is given by :

[tex]V=\pi r^2 h\\\\V=\dfrac{22}{7} \times (4)^2 \times 13\\\\V=653.71\ \text{cm}^3[/tex]

So, the volume of the cylinder is [tex]653.71\ \text{cm}^3[/tex]

Answer:

653.45 is the answer

Explanation:

Answer:

The difference between One-way as well as reversible rotary motion​ is described below.

Explanation:

Answer:

The weak force governs the decay of a neutron into a proton (a process known as beta decay). The strong force binds quarks together into protons and neutrons (the residual strong force holds protons and neutrons together in the nucleus). Gravity governs the motion of an apple falling from a tree.

Explanation:

Answer:

Weak Nuclear force

Answer: React with the skin

Explanation:

lab safety test Safety goggles and an apron must be worn when handling chemicals labeled corrosive because they React with the skin

This question is incomplete; here is the complete question:

Marco is conducting an experiment. He knows the wave that he is working with has a wavelength of 32.4 cm. If he measures the frequency as 3 hertz, which statement about the wave is accurate?

A. The wave has traveled 32.4 cm in 3 seconds.

B. The wave has traveled 32.4 cm in 9 seconds.

C. The wave has traveled 97.2 cm in 3 seconds.

D. The wave has traveled 97.2 cm in 1 second.

The answer to this question is D. The wave has traveled 97.2 cm in 1 second.

Explanation:

The frequency of a wave, which is in this case 3 hertz, represents the number of waves that go through a point during 1 second. According to this, if the frequency of the wave is 3 hertz this means in 1 second there were 3 waves. Moreover, if you multiply the wavelength (32.4cm) by the frequency (3) you will know the distance the wave traveled in 1 second: 32.4 x 3 =  97.2 cm. This makes option D the correct one as the distance in 1 second was 97.2 cm.

Answer:Is D!

Explanation:TEAT(Sorry) -_-*

Answer:

1) It means that the acceleration is 0

2) Momentum, p = Mass, m × Velocity, v

3) Newton's second law of motion

4) The conditions where there are no resultant forces acting on the object

Explanation:

1) The value v - u =  0 means that the acceleration is 0

The relation between v and u is v = u + a·t

v - u = a·t

When v - u = 0 we have;

a·t = 0

a = 0 or t = 0

Acceleration, a = 0

2) The relation between momentum, mass and velocity is

Momentum, p = Mass, m × Velocity, v

p = m × v

3) The bus moving a little distance forward even when the breaks are applied is due to the following relation;

Force = Rate of change of momentum produced

Which is Newton's second law of motion

Therefore, where the the force is low, the rate of change of the momentum and therefore, the velocity will be low, and the bus will still move further after applying the breaks

4) According to Newton's first law of motion, the conditions under which the acceleration of a moving object will be zero includes conditions where there are no resultant forces acting on the object.

Answer:

22.2 m/s or 80 km/h

Explanation:

Given that

Distance travelled by the car, d = 240 km

Time taken by the car, t = 3 hours.

Speed of the car, v = ? m/s

for easy calculations, we will be converting the units to meters and seconds respectively.

240 km to meters would be

240 * 1000 m = 240000 m

3 hrs to seconds would be

3 * 60 mins * 60 seconds = 10800 s

now, we have our distance and time to be

d = 240000 m

t = 10800 s

speed is defined as the ratio of distance with respect to time taken, effectively,

Speed = distance/time

speed, v= 240000 / 10800

v = 22.2 m/s

therefore, the speed of the car during the time is 22.2 m/s, or if the speed is needed in km/h, we can convert it

22.2 * 3600/1000 =

80 km/h

Answer:

A. It is always a positive force

Explanation:

Hooke's law describes the relation between an applied force and extension ability of an elastic material. The law states that provided the elastic limit, e, of a material is not exceeded, the force, F, applied is proportional to the extension, x, provided temperature is constant.

i.e F = - kx

where k is the constant of proportionality, and the minus sign implies that the force is a restoring force.

The applied force can either be compressing or stretching force.

Answer:

Average acceleration = Displacement / (time)^2

Explanation:

The unit for acceleration is

[tex]m {s}^{ - 2} [/tex]

Displacement = m

Time = s

Hence the units of displacement and time should be manipulated to get the unit of acceleration.

You can't. You can only find average velocity.

But if you also know that initial velocity is zero ... the object started from rest ... then

Avg acceleration =

2 x displacement / time-squared

Answer:

a)0.51°

b)1.47×10^-4m

Explanation:

a)for a single slit experiment, the minima that has an angle of θ towards the centre needs to satisfy the expression below.

bsin(θ)= mλ.........................(*)

Where b= width of the slit

The distance on the screen from Central angle can be expressed as

Sin(θ)= y/d............. (**)

d and y is the horizontal distance between slit and screen

If we input eqn(**) into equation (*) we have

y= mλd/b................(z)

In order to find angle (θ) we have

(θ)= sin-(1.99×10^-2)/2.25

= 0.51°

Therefore, angle of diffraction θ of the second minimum is 0.51°

b)to find the width of the sloth using eqn(z) by substitute the values, we have

b= (2)(649×10^-9)(2.25)/1.99×10^-2

b= 1.47×10^-4m

Therefore, the width of the slit is 1.47×10^-4m

Answer:

its velocity, wavelength and frequency all change

Explanation:

Whenever a wave crosses the boundary between two media of different densities, its velocity, frequency and wavelength changes. This appears as a bending of the wave as it crosses the boundary from one medium to another.

Refraction is a fundamental property of waves. Hence when light is travelling from air into water, it wavelength, speed and frequency all changes at the interface between the two media.

Answer:

first part the skater goes down a constant slope ramp, initially he has Newton's second law

pply Newton's third law, the normal is the reaction to the support of the body on the surface

the ramp shoots off.  axis becomes zero and therefore with Newton's first law its speed

Explanation:

It is the description of this movement let's write Newton's laws.

* The first law that a body goes at constant speed or zero if the sum of the external forces is zero

* the second law is F = m a

* The third law states that the forces act in pairs of equal magnitude and opposite direction, one applied to each body.

Let's apply these laws to our case

In the first part the skater goes down a constant slope ramp, initially he has Newton's second law when he accelerates from the initial velocity of zero to a terminal velocity.

The expression for this is

             Wₓ - fr = ma

             W sin θ - μ W cos θ = m a

             W = mg

             g (sin θ - μ cos) = a

the value of the coefficient of kinetic friction depends on the condition of the surface, dry, wet or muddy

This is Newton's second law

On the Y axis, which is perpendicular to the ramp we have

            N- [tex]W_{y}[/tex] = 0

If we apply Newton's third law, the normal is the reaction to the support of the body on the surface, note that it can be different from the weight.

In the second part when he is on the ramp.

In the ramp the skater enters with a speed v, suppose that the ramp has an incline so that the skater can jump, in this case the angle is positive with respect to the axis x

In this case the analysis is similar to the previous one

Newton's second law gives the acceleration of the skater, who when he reaches the end of the ramp shoots off.

 At this point the force in the x (horizontal) axis becomes zero and therefore with Newton's first law its speed this axis remains constant and the force in the y axis is the force of gravity and has an acceleration that changes if velocity according to Newton's second law

Answer:look at explanations

Explanation:

Answer:

17.15 m

Explanation:

Assuming the well is empty (full of air instead of water), the speed of sound is v = 343 m/s.

The water well acts as a pipe closed at one end.  Therefore, the depth of the water well must be an odd multiple of a quarter of the resonant wavelength.

L = (2n − 1) λ/4, n = 1, 2, 3, etc.

v = λf, so λ = v/f.  Substituting:

L = (2n − 1) v/(4f)

Solving for frequency:

f = (2n − 1) v/(4L)

The difference between two successive resonant frequencies is therefore:

Δf = (2(n+1) − 1) v/(4L) − (2n − 1) v/(4L)

Δf = (2n + 1) v/(4L) − (2n − 1) v/(4L)

Δf = 2 v/(4L)

Δf = v/(2L)

Plugging in values:

50 Hz − 40 Hz = 343 m/s / (2L)

2L = 34.3 m

L = 17.15 m

Answer:

We have the position vector given in terms of time t. r(t) = t^3*i + t^2*j

To find the velocity vector we have to differentiate r(t) with respect to time.

r'(t) = 3t^2*i + 2t*j

The vector representing acceleration is the derivative of the position vector

r''(t) = 6t*i + 2*j

When time t = 2.

The velocity vector is 3*2^2*i + 2*2*j

=> 12*i + 4*j

The speed is the absolute value of the velocity vector or sqrt(12^2 + 4^2) = sqrt (144 + 16) = sqrt 160

The acceleration vector is 6*2*i + 2*j

=> 12*i + 2*j

The required acceleration at t=2 is 12*i + 2*j and the speed is sqrt 160.

Explanation:

Can I have thx and brainliest?

Answer:

8 atm

Explanation:

Ideal gas law:

PV = nRT

where P is pressure, V is volume, n is moles, R is universal gas constant, and T is absolute temperature.

If n is constant:

PV / T = PV / T

(4 atm) (60 L) / (27 + 273) K = P (40 L) / (127 + 273) K

0.8 atm = 0.1 P

P = 8 atm

Answer:

lathe

perfectly symmetrical

Answer: A lathe is used to turn wood . It rotates and carves wood to produce a perfectly symmetrical form .

First one is lathe .

Second one is perfectly symmetrical .

Explanation: I just took the test on Plato and had 100%

Answer: Bleach is a base

Explanation:  If bleach had a pH level of 12, a number above 7, than it is a base.  Hope this helps!

Answer:

The law of conservation of momentum states that the total momentum of interacting objects does not change. This means the total momentum before a collision or explosion is equal to the total momentum after a collision or explosion.

Answer:

The answer is

Explanation:

Change. Does not change.means.

Hope this helps....

Have a nice day!!!!