Answer:
ML/T^2
this is the correct answer
what is the si unit of potential difference
Answer:
The answer is volt (V).
Explanation:
Volt is the SI unit of potential difference. The symbol of volt is V.
what is 222 divided by 11.2
Answer:
The answer of this question is 19.89142857
Answer:
The number 222 is called the numerator or dividend, and the number 11 is called the denominator or divisor.
The quotient of 222 and 11, the ratio of 222 and 11, as well as the fraction of 222 and 11 all mean (almost) the same:
222 divided by 11, often written as 222/11.
Read on to find the result of 222 divided by 11 in decimal notation, along with its properties.
Explanation:
9. SAFELY BACKING UP YOUR VEHICLE INCLUDES ALL OF THE FOLLOWING
EXCEPT:
A. Looking over your right shoulder as you back up
O B. Checking behind your vehicle before you get in
C. Tapping your horn before you back up
Which is one factor that scientists use to classify orders of soil?Which phrase best describes the biosphere?
Yall pls help me out
Determine the dimensions for T if T = M V^2 A / L^3 where M is a mass, V is a velocity, A is an area, and L is a length.
L / T
No dimensions
M L / T^2
M
M / (L T^2)
Answer:
M·L/T²
Explanation:
The given equation for T is presented as follows;
[tex]T = \dfrac{M \cdot V^2 \cdot A}{L^3}[/tex]
Where;
m = Mass with dimension M
V = Velocity, having the dimensions L/T
A = Area, having the dimensions L²
l = Length, having the dimensions, L
Therefore;
[tex]The \ dimensions \ of \ T = \dfrac{M \times (L/T)^2 \cdot L^2}{L^3} = \dfrac{M \times L^4/T^2 }{L^3} = M \cdot L/T^2[/tex]
The low-pressure fuel system is being discussed. Technician A says that the system must provide an adequate volume of fuel to the high-pressure fuel injection system. Technician B says that the system must provide fuel at a minimum pressure to the high-pressure fuel injection system. Which technician is correct
Answer:
Hence Both technicians A and B are correct that is Technician A says that the system must provide an adequate volume of fuel to the high-pressure fuel injection system. Technician B says that the system must provide fuel at a minimum pressure to the high-pressure fuel injection system are true.
Explanation:
The low-pressure fuel system contains the fuel filters; A fuel level sending unit/tank pick-up; A transfer pump. So from considering both technicians statements both are applicable.
Explanation:
MARK ME AS A BRIANLIEST .........Determine the dimensions for R if R = m V / (d^2 Q) where m is a mass, V is a velocity, d is a diameter, and the dimensions of Q are M/(LT).
No dimensions
M / (L T^2)
M L / T^2
M
L / T
Answer:
No dimension
Explanation:
The given equation is [tex]R = \dfrac{m \cdot V}{d^2 \cdot Q}[/tex], where;
m = Mass
V = Velocity
d = A diameter
The dimension of mass quantity = M
The dimension of the velocity quantity = L/T
The dimension of the dimeter quantity = L
The given dimension of Q = M/(L·T)
Therefore, we get;
[tex]The \ dimension \ of \ R = \dfrac{M \times L/T}{L^2 \times (M/LT)} = \dfrac{M \times L/T}{L \times M/T} = 1[/tex]
Therefore, R has no dimensions
The diesel fuel cooler is being discussed. Technician A says that high-pressure fuel systems generate a lot of heat. Technician B says that temperature affects the density of the diesel fuel. Which technician is correct
Answer:
Both the technicians are correct.
Explanation:
As the pressure increases the temperature will also increase in accordance with the Boyle's law hence greater amount of heat is formed.
[tex]Pressure\propto Temperature[/tex]
When the temperature increases the intermolecular spaces increase as the molecules of the fuel gain energy and their kinetic energy increases. This is limited to temperatures below dissociation/combustion temperature of diesel .
write growth rate of tree ( engineering)
Which of the following statements is correct?
Adhesive bonding allows several individual parts to be connected with nuts and bolts.
Rivets are temporary fasteners that bind two plates of metal together.
Both soldering and brazing are structurally stronger than welding.
Hardware assembly is primarily used when there is a need of being able to take individual parts out of an assembly throughout the life cycle of the product.
Answer:
b. rivets are tempory fasteners that bind two plate of metals together
what is grain of timber
locução adjetiva e de portuges ou istoria
rt this question on a NEW page Give ONE word/tem for each of the following descriptions by choosing a word/term from the list below. Write only the word/term next to the question numbers (1.1.1. to 1.1.5) in the ANSWER BOOK, e.g. 1.1.6 casement curiog: electroplating: . galvanising; powder coating; paint; turpentine; sanding sealer 1.1.1 Available in a water- or oil-based liquid 1.1.2 Allows concrete to achieve its optimal strength 1.1.3 Coating a metal by the process el electrolysis 1.1.4 Can be melted again because nc chemical process is involved 1.1.5 Adds strength to the original uncoated metal FIGURE 1.2 below shows equipment that is used on a construction site
Answer:
oh I am sorry I can't understand your question.
George is replacing a burned out resistor in a circuit board. The board has a 10, a 20, and a 40 on resistor, all in parallel. When George has sided in the new component in the circuit is fixed, he checks his multimeter. What reading does he get?
Answer:
5.71 ohms
Explanation:
put it in the calculator
Herramientas para la instalación de un picaporte
Answer:
Un picaporte es una palanca en ángulo para abrir y cerrar una puerta a mano. Por lo general, el picaporte se empuja hacia abajo para abrir la puerta. El mecanismo de la cerradura de la puerta hace que el pestillo de la cerradura se salga de la placa de la cerradura mediante la rotación del pasador. No es necesario accionar el pestillo para cerrar la puerta, ya que el pestillo encaja automáticamente en su lugar.
La conexión entre las manijas de las puertas, que generalmente están unidas a ambos lados de la hoja de la puerta, se realiza mediante un pasador cuadrado. El mandril también establece la conexión con el mecanismo de la cerradura: su escuadra es guiada a través de la escuadra interior del seguidor de la manija de la cerradura, para que gire junto con ella.
Por lo tanto, las herramientas que tienen un rol en la instalación de un picaporte son, principalmente, una agujereadora para ingresar las fijaciones, destornillador y tornillos, martillo y clavos.
True or false: Units and dimensions are interchangeable words that describe the same concept.
True
False
Answer:
The answer to this is false
Explanation:
It is FALSE that units and dimensions are interchangeable words that describe the same concept.
What are units and dimension?Units is defined as a measure of quantity while dimension specify the measure of a line or curve.
Both terms cannot be used interchangeably even though the dimensions of a quantity is derived from its units.
Learn more o unit ad dimension here: https://brainly.com/question/28464
#SPJ2
