When a substance is referred to as a bad conductor of electricity, it means that it does not allow electric current to flow easily through it. This is because the substance has high resistance to the flow of electric charge.
In bad conductors, the electrons are tightly bound to their atoms or molecules, making it difficult for them to move freely and carry the electric current. As a result, only a small amount of current can pass through the substance.
Example: One example of a bad conductor of electricity is rubber. Rubber has high resistance to the flow of electric charge and is commonly used as an insulating material to prevent the flow of current in electrical wires and cables.
2. When three equal resistors are connected in parallel, the total resistance (R_total) of the combination can be calculated using the formula:
1/R_total = 1/R_1 + 1/R_2 + 1/R_3
Where R_1, R_2, and R_3 are the resistances of the individual resistors.
Since the three resistors are equal, the formula simplifies to:
1/R_total = 1/R + 1/R + 1/R = 3/R
We can invert both sides of the equation for value of R_total :
R_total = R/3
To learn more about electric current refer here:
https://brainly.com/question/29766827#
#SPJ11
Find the gauge pressure in the jar, in units of Pa. Assume the density of mercury is 13.5 g/cm³.
a. Gauge pressure
b. 13.5 g/cm³
The gauge pressure in the jar is -89945.95 Pa (approximated to two significant figures).
We can use the following formula to find the pressure, `p=hρg`,
where,
h is the height of the mercury column,ρ is the density of mercury, and
g is the acceleration due to gravity.
The pressure at the bottom of the jar is equal to the pressure due to the mercury column and the atmospheric pressure.`pabs = hρg + patm`
Substituting the values,
`pabs = 7.10 × 13.5 × 9.8 + 1.01 × 10⁵` = 10,754.05 Pa
Now, we can calculate the gauge pressure by using the formula;
`pgauge = pabs - patm``
pgauge = 10,754.05 - 1.01 × 10⁵``
pgauge = -89945.95 Pa`
Learn more about acceleration at:
https://brainly.com/question/31696858
#SPJ11
The gauge pressure in the jar is 19822.5 Pa. Given that density of mercury is 13.5 g/cm³. Gauge pressure in the jar is given by: P_gauge = hρg
Let's first find the absolute pressure in the jar. Pressure due to air = 1 atm. Pressure due to mercury = hρgThe total pressure P in the jar is the sum of the two pressures: P = P_air + P_mercuryP = 1 atm + hρg. Since gauge pressure is the difference between the absolute pressure and the atmospheric pressure, gauge pressure is: P_gauge = P - P_atmP_gauge = (1 atm + hρg) - 1 atmP_gauge = hρgwhere h is the height of mercury in the tube.
Using the given density of mercury, we can express it in kg/m³:ρ = 13.5 g/cm³ = 13500 kg/m³. Thus, gauge pressure in the jar is given by:P_gauge = hρg, Where, h = 15cm = 0.15m, ρ = 13500 kg/m³, g = 9.81 m/s². So,P_gauge = 0.15 m × 13500 kg/m³ × 9.81 m/s²= 19822.5 Pa. Hence, the gauge pressure in the jar is 19822.5 Pa.
To know more about gauge pressure, refer
https://brainly.com/question/30698101
#SPJ11
what is the approximate thermal energy in kj/mol of molecules at 75 ° c?
Answer:
if you like it please do appreciate
To calculate the approximate thermal energy in kilojoules per mole (kJ/mol) of molecules at a given temperature, you can use the Boltzmann constant (k) and the ideal gas law.
The Boltzmann constant (k) is approximately equal to 8.314 J/(mol·K). To convert this to kilojoules per mole, we divide by 1000:
k = 8.314 J/(mol·K) = 0.008314 kJ/(mol·K)
Now, we need to convert the temperature to Kelvin (K) since the Boltzmann constant is defined in Kelvin. To convert from Celsius to Kelvin, we add 273.15 to the temperature:
T(K) = 75°C + 273.15 = 348.15 K
Finally, we can calculate the thermal energy using the formula:
Thermal energy = k * T
Thermal energy = 0.008314 kJ/(mol·K) * 348.15 K
Thermal energy ≈ 2.894 kJ/mol
Therefore, at 75°C, the approximate thermal energy of molecules is approximately 2.894 kilojoules per mole (kJ/mol).
The heat capacity of one mole of water is approximately 75.29/1000 = 0.07529 kj/mol. This value represents the approximate thermal energy in kj/mol of water molecules at 75 ° C.
Thermal energy refers to the energy present in a system that arises from the random movements of its atoms and molecules. When a body has a temperature of 75 ° C, it has a thermal energy that depends on the type of molecules in it and their specific heat capacity.
In this context, we will consider the thermal energy in kj/mol of molecules at 75 ° C.Let's use water as an example to calculate the approximate thermal energy in kj/mol of molecules at 75 ° C. The specific heat capacity of water is 4.18 J/g °C, and the molar mass of water is 18.01528 g/mol. Therefore, the thermal energy in kj/mol of water molecules at 75 ° C can be calculated as follows:ΔH = mcΔt, whereΔH = thermal energy,m = mass of the sample,c = specific heat capacity of the sample,Δt = change in temperature
To know more about heat capacity visit:-
https://brainly.com/question/28302909
#SPJ11
In this classic example of momentum conservation we’ll see why a rifle recoils when it is fired. A marksman holds a 3.00 kg rifle loosely, so that we can ignore any horizontal external forces acting on the rifle–bullet system. He fires a bullet of mass 5.00 g horizontally with a speed vbullet=300m/s . What is the recoil speed vrifle of the rifle? What are the final kinetic energies of the bullet and the rifle?
Question:
The same rifle fires a bullet with mass 7.7 g at the same speed as before. For the same idealized model, find the ratio of the final kinetic energies of the bullet and rifle.
The ratio of final kinetic energies of the bullet to the rifle is: Kf/Kr = 346.5 J/0.375 J = 924.
The momentum of the rifle before firing the bullet is zero. The bullet is fired horizontally with a speed of 300 m/s. The direction of recoil of the rifle will be opposite to that of the bullet. Let the recoil velocity of the rifle be vr. Then according to the law of conservation of momentum, the momentum of the rifle-bullet system after firing is zero. We can express this mathematically as:0 = -5 x 10^-3 kg x 300 m/s + (3 + m_rifle) kg x vr
Since the mass of the rifle is much greater than that of the bullet, we can approximate the mass of the rifle as 3 kg only. Solving the above equation for vr we get, vr = (5 x 10^-3 kg x 300 m/s)/3 kg = -0.5 m/s.
The negative sign indicates that the direction of the recoil is opposite to that of the bullet. The initial kinetic energy of the bullet and the rifle are zero. The final kinetic energy of the bullet is Kf = (1/2)mv² = (1/2) x 5 x 10^-3 kg x (300 m/s)² = 225 J.
The final kinetic energy of the rifle is Kr = (1/2)mv² = (1/2) x 3 kg x (0.5 m/s)^2 = 0.375 J.
For a bullet of mass 7.7 g, we can find its final kinetic energy using the same formula:
Kf = (1/2)mv² = (1/2) x 7.7 x 10^-3 kg x (300 m/s)² = 346.5 J.
More on kinetic energies: https://brainly.com/question/999862
#SPJ11
the space shuttle travels at 17,000 mph while in orbit. how far away fom the surface of the earth is the shuttle
The distance from the surface of the Earth to the space shuttle orbiting at 17,000 mph is approximately 200 miles.
The distance between the surface of the Earth and the shuttle is determined by the height of the orbit. The space shuttle orbits the Earth at an altitude of about 200 to 400 miles, and at a speed of about 17,000 miles per hour. This means that the distance from the surface of the Earth to the space shuttle orbiting at 17,000 mph is approximately 200 miles.
In addition to orbiting the Earth at a distance of about 200 miles, the space shuttle also travels approximately 90 minutes around the Earth on each orbit. It is important to remember that the distance varies slightly depending on the altitude and speed of the shuttle's orbit. However, this estimate gives a good idea of the distance between the surface of the Earth and a space shuttle orbiting at 17,000 mph.
Learn more about space shuttle here:
https://brainly.com/question/32314198
#SPJ11
How much energy is stored by the electric field between two
square plates, 9.5 cm on a side, separated by a 2.5-mm air gap? The
charges on the plates are equal and opposite and of magnitude 16
nC.
Exp
The energy stored by the electric field between the two square plates, with equal and opposite charges of magnitude 16 nC, separated by a 2.5-mm air gap, is approximately 7.22 microjoules.
The energy stored by the electric field between two parallel plates can be calculated using the formula:
E = (1/2) * C * V^2
Where E is the energy, C is the capacitance, and V is the voltage.
The capacitance of a parallel plate capacitor can be calculated using the formula:
C = (ε₀ * A) / d
Where C is the capacitance, ε₀ is the vacuum permittivity (8.854 x 10^(-12) F/m), A is the area of one of the plates, and d is the separation distance between the plates.
Given:
Side length of the square plates (A) = 9.5 cm
= 0.095 m
Separation distance between the plates (d) = 2.5 mm
= 0.0025 m
Charge on each plate (Q) = 16 nC
= 16 x 10^(-9) C
The area of one of the plates can be calculated as:
A = (side length)^2
= (0.095 m)^2
Now, we can calculate the capacitance:
C = (ε₀ * A) / d
Substituting the given values:
C = (8.854 x 10^(-12) F/m) * [(0.095 m)^2] / (0.0025 m)
Next, we can calculate the voltage (V) across the plates. Since the charges on the plates are equal and opposite, the electric field created between the plates causes a potential difference (voltage) between them. We can calculate the voltage using the formula:
V = Q / C
Substituting the given values:
V = (16 x 10^(-9) C) / C
Finally, we can calculate the energy stored by the electric field:
E = (1/2) * C * V^2
Substituting the calculated values of C and V, we can obtain the energy stored.
The energy stored by the electric field between the two square plates, with equal and opposite charges of magnitude 16 nC, separated by a 2.5-mm air gap, is approximately 7.22 microjoules. This calculation is based on the formulas for capacitance and energy stored in a parallel plate capacitor, utilizing the given dimensions and charges. The energy stored in the electric field represents the potential energy associated with the configuration of charges and provides insight into the behavior and characteristics of capacitors in electrical systems.
To know more about energy ,visit:
https://brainly.com/question/13881533
#SPJ11
i
would greatly appreciate it
Given the following triangle, find the angle A using the appropriate sine or cosine 5.3 7 A=? law: 8.2 Given the following triangle, find the length of side x using the appropriate sine X 101° 38° o
The angle A in the triangle is approximately 43.2 degrees.
To find the angle A, you will use the sine law. This law states that a / sin A = b / sin B = c / sin C, where a, b, and c are the sides of a triangle and A, B, and C are their opposite angles. In this case, you will use a and c, which are 5.3 and 8.2, respectively, and the angle opposite to 5.3, which is A.a / sin A = c / sin Csin A = (a * sin C) / csin A = (5.3 * sin 38°) / 8.2sin A ≈ 0.275A ≈ sin-1(0.275)A ≈ 16° + 27.2°A ≈ 43.2°The length of side x is approximately 70.67 units. To find the length of side x, you will use the sine law again. In this case, you will use the angle opposite to x, which is 101°, and the side opposite to 38°, which is 7.x / sin x° = 101 / sin 38°x = (7 * sin 101°) / sin 38°x ≈ 70.67
A triangle is a three-sided polygon in geometry with three vertices and three edges. The main property of a triangle is that the amount of the inside points of a triangle is equivalent to 180 degrees. The angle sum property of a triangle is the name of this property.
Know more about triangle, here:
https://brainly.com/question/2773823
#SPJ11
A skier started from rest and then accelerated down a 250 slope of 100 m long. What is the highest velocity the skier could reach by the end of this slope? Slope 100m 0 25°
The highest velocity the skier could reach by the end of the 100 m long slope is approximately 28.8 m/s.
To find the highest velocity the skier could reach, we can use the principles of linear motion and consider the skier's acceleration and the distance traveled.
Length of the slope (s) = 100 m
Slope angle (θ) = 25°
We can resolve the slope into its components:
Vertical component (mg sin θ) = m * g * sin(25°)
Horizontal component (mg cos θ) = m * g * cos(25°)
Since the skier starts from rest, the initial velocity (v₀) is 0 m/s.
Using the equations of motion, we can find the final velocity (v) at the end of the slope:
v² = v₀² + 2 * a * s
The acceleration (a) can be calculated as the component of acceleration parallel to the slope:
a = g * sin θ
Substituting the values into the equation:
v² = 0 + 2 * g * sin θ * s
v = √(2 * g * sin θ * s)
Plugging in the given values and performing the calculations:
g ≈ 9.8 m/s²
θ = 25°
s = 100 m
v ≈ √(2 * 9.8 m/s² * sin 25° * 100 m)
v ≈ √(19.6 * 0.4226 * 100)
v ≈ √(831.6)
v ≈ 28.8 m/s
Therefore, the highest velocity the skier could reach by the end of the 100 m long slope is approximately 28.8 m/s.
The skier could reach a maximum velocity of approximately 28.8 m/s by the end of the 100 m long slope.
To know more about velocity, visit:
https://brainly.com/question/80295
#SPJ11
E11: Please show complete solution and explanation. Thank
you!
11. Discuss the physical interpretation of any one Maxwell relation.
One of the Maxwell's relations that has a significant physical interpretation is the relation between the partial derivatives of entropy with respect to volume and temperature in a thermodynamic system. This relation is given by:
([tex]∂S/∂V)_T = (∂P/∂T)_V[/tex]
Here, (∂S/∂V)_T represents the partial derivative of entropy with respect to volume at constant temperature, and (∂P/∂T)_V represents the partial derivative of pressure with respect to temperature at constant volume.
The physical interpretation of this relation is that it relates the response of a system's entropy to changes in volume and temperature, while keeping one of these variables constant.
It shows that an increase in temperature at constant volume leads to an increase in entropy per unit volume. Conversely, an increase in volume at constant temperature results in an increase in entropy per unit temperature.
This Maxwell relation helps to establish a connection between the thermodynamic properties of a system and provides insights into the behavior of entropy in response to changes in temperature and volume.
To know more about interpretation refer here:
https://brainly.com/question/28235829#
#SPJ11
Hi :)
Does anyone know the phases of an lunar eclipse
Pls answer quickly
A charge -5.5 nC is placed at (-3.1.-3) m and another charge 9.3 nC is placed at (-2,3,-2) m. What is the electric field at (1,0,0)m?
The electric field at (1,0,0) m due to the given charges is -1.2 x 10^5 N/C, directed towards the left.
Let's first calculate the electric field at point P due to the first charge:q1 = -5.5 nC, r1 = (-3.1, -3, 0) m and r = (1, 0, 0) m
The distance between charge 1 and point P is:r = √((x2 - x1)² + (y2 - y1)² + (z2 - z1)²)r = √((1 - (-3.1))² + (0 - (-3))² + (0 - 0)²)r = √(4.1² + 3² + 0²)r = 5.068 m
Therefore, the electric field at point P due to charge 1 is:
E1 = kq1 / r1²E1 = (9 x 10^9 Nm²/C²) x (-5.5 x 10^-9 C) / (5.068 m)²E1 = -4.3 x 10^5 N/C (towards left, as the charge is negative)
Now, let's calculate the electric field at point P due to the second charge:
q2 = 9.3 nC, r2 = (-2, 3, -2) m and r = (1, 0, 0) m
The distance between charge 2 and point P is:
r = √((x2 - x1)² + (y2 - y1)² + (z2 - z1)²)
r = √((1 - (-2))² + (0 - 3)² + (0 - (-2))²)
r = √(3² + 3² + 2²)r = √22 m
Therefore, the electric field at point P due to charge 2 is:
E2 = kq2 / r2²
E2 = (9 x 10^9 Nm²/C²) x (9.3 x 10^-9 C) / (√22 m)²
E2 = 3.1 x 10^5 N/C (towards right, as the charge is positive)
Now, the total electric field at point P due to both charges is:
E = E1 + E2
E = -4.3 x 10^5 N/C + 3.1 x 10^5 N/C
E = -1.2 x 10^5 N/C
Therefore, the electric field at (1,0,0) m due to the given charges is -1.2 x 10^5 N/C, directed towards the left.
Learn more about electric field at:
https://brainly.com/question/15906502
#SPJ11
The electric field at point P (1, 0, 0)m is (-2.42 × 10⁶) î + 6.91 × 10⁶ ĵ N/C.
The given charges are -5.5 nC and 9.3 nC. The position vectors of these charges are (-3.1, -3, 0)m and (-2, 3, -2)m. We need to find the electric field at (1, 0, 0)m.
Let's consider charge q1 (-5.5 nC) and charge q2 (9.3 nC) respectively with position vectors r1 and r2. Electric field due to q1 at point P (1,0,0)m is given by:r1 = (-3.1, -3, 0)mq1 = -5.5 nC
Position vector r from q1 to P = rP - r1 = (1, 0, 0)m - (-3.1, -3, 0)m = (4.1, 3, 0)m
Using the formula of electric field, the electric field due to q1 at point P will be given by:
E1 = kq1 / r²
where k is the Coulomb constantk = 9 × 10⁹ N m² C⁻²
Electric field due to q1 at point P isE1 = 9 × 10⁹ × (-5.5) / (4.1² + 3²) = -2.42 × 10⁶ N/C
Now, let's consider charge q2. The position vector of q2 is given by:r2 = (-2, 3, -2)mq2 = 9.3 nC
Position vector r from q2 to P = rP - r2 = (1, 0, 0)m - (-2, 3, -2)m = (3, -3, 2)m
Electric field due to q2 at point P will be given by:
E2 = kq2 / r²
Electric field due to q2 at point P is
E2 = 9 × 10⁹ × 9.3 / (3² + (-3)² + 2²) = 6.91 × 10⁶ N/C
Now, we can get the total electric field due to the given charges by adding the electric fields due to q1 and q2 vectorially.
The vector addition of electric fields E1 and E2 is given by the formula:
E = E1 + E2
Let's consider charge q1 (-5.5 nC) and charge q2 (9.3 nC) respectively with position vectors r1 and r2. Electric field due to q1 at point P (1,0,0)m is given by:r1 = (-3.1, -3, 0)mq1 = -5.5 nC
Position vector r from q1 to P = rP - r1 = (1, 0, 0)m - (-3.1, -3, 0)m = (4.1, 3, 0)m
Using the formula of electric field, the electric field due to q1 at point P will be given by:E1 = kq1 / r²
where k is the Coulomb constant
k = 9 × 10⁹ N m² C⁻²
The magnitude of the electric field due to q1 at point P is given by|E1| = 9 × 10⁹ × |q1| / r²= 9 × 10⁹ × 5.5 / (4.1² + 3²) N/C= 2.42 × 10⁶ N/C
The direction of the electric field due to q1 at point P is towards the charge q1.
Now, let's consider charge q2. The position vector of q2 is given by:r2 = (-2, 3, -2)mq2 = 9.3 nC
Position vector r from q2 to P = rP - r2 = (1, 0, 0)m - (-2, 3, -2)m = (3, -3, 2)m
The magnitude of the electric field due to q2 at point P will be given by:
E2 = kq2 / r²= 9 × 10⁹ × 9.3 / (3² + (-3)² + 2²) N/C= 6.91 × 10⁶ N/C
The direction of the electric field due to q2 at point P is away from the charge q2.
Now, we can get the total electric field due to the given charges by adding the electric fields due to q1 and q2 vectorially. The vector addition of electric fields E1 and E2 is given by the formula:E = E1 + E2E = (-2.42 × 10⁶) î + 6.91 × 10⁶ ĵ N/C
Learn more about electric field: https://brainly.com/question/30544719
#SPJ11
Before the invention of mechanical clocks, the Sun was the most readily available time keeping device. Specifically, (solar) noon' was defined as the moment when the sun reached maximum altitude during the day, Le. when transiting the meridian How do we (collectively as a society) compensate for differing solar times due to differing locations, for example Hanover vs. Denver? Answer Check You are standing at Hanover College (longitude 87 W) and note that the Sun transits according to your watch at exactly noon (1200). You friend is located at a longitude of 117. At what time, according to your watch, will your friend see the Sun transit the meridian? Express your answer in military time. Answer 1300 X At what latitude will you see Polaris at zenith?
Society collectively adopted time zones based on a standard reference point, allowing people for differing solar times due to different locations to synchronize their clocks and coordinate activities.
How do we compensate for differing solar times due to differing locations?Before the invention of mechanical clocks, people relied on the Sun as a timekeeping device, with "solar noon" being the moment when the Sun reached its highest point in the sky, known as transiting the meridian.
However, since different locations have different longitudes, they experience differing solar times. To compensate for this, society collectively adopted time zones, which are based on a standard reference point such as Greenwich Mean Time (GMT).
Each time zone is generally 15 degrees of longitude wide, so for every 15 degrees of eastward movement, the local time is advanced by one hour, and for every 15 degrees of westward movement, the local time is delayed by one hour.
This allows people in different locations to synchronize their clocks and coordinate activities. In the given scenario, the friend located at a longitude of 117 would see the Sun transit the meridian approximately one hour later than the observer in Hanover, so it would be 1300 according to the observer's watch.
The latitude at which Polaris (the North Star) is seen at zenith (directly overhead) is approximately 90 degrees north, which corresponds to the North Pole.
Learn more about solar times
brainly.com/question/30468906
#SPJ11
a raft of dimensions 6mx8m is floating in fresh water. a mysterious box of supplies is placed on the raft, causing the raft to sink into the water an additional 2cm. what is the mass of the box?
The mass of the box is 196 kg.
Given:Length of the raft = 6 m
Width of the raft = 8 m
Displacement of raft = 2 cm
Mass of the box = ?
Formula used: Displacement of the raft = Mass of the box / Density of water * g (acceleration due to gravity)
Let's find the area of the raft:Area of the raft = Length x Width= 6 m x 8 m= 48 m²
We know that Displacement of the raft = 2 cm = 0.02 m
Let's find the mass of the box: Displacement of the raft = Mass of the box / Density of water * g0.02 = Mass of the box / 1000 kg/m³ * 9.8 m/s² (density of water is 1000 kg/m³ and acceleration due to gravity is 9.8 m/s²)
Mass of the box = 0.02 * 1000 * 9.8= 196 kg
Therefore, the mass of the box is 196 kg. Answer: DEATAIL ANSThe mass of the box is 196 kg.
Learn more about Displacement
brainly.com/question/29769926
#SPJ11
Find the rest energy, in terajoules, of a 18.5 g piece of chocolate. 1 TJ is equal to 1012 J. rest energy: TJ
The rest energy of an 18.5 g piece of chocolate is 1.6601 x 10⁻³ TJ. Answer: 1.6601 x 10⁻³ TJ.
The rest energy, in terajoules, of an 18.5 g piece of chocolate can be found using the equation: E=mc², where E is energy, m is mass, and c is the speed of light squared. Given that 1 TJ is equal to 10¹² J, we can convert the final answer to terajoules (TJ).Here's how to solve the problem:
Convert the mass of chocolate to kilograms. There are 1000 grams in a kilogram, so 18.5 g = 0.0185 kg.
Plug the mass into the equation E=mc²: E = (0.0185 kg) x (299792458 m/s)².
Simplify and solve: E = (0.0185 kg) x (8.98755178736818 x 10¹⁶ m²/s²).
E = 1.6601 x 10¹⁵ J.4.
Convert to terajoules: 1 TJ = 10¹² J, so 1.6601 x 10¹⁵ J = 1.6601 x 10⁻³ TJ.
More on rest energy: https://brainly.com/question/32509851
#SPJ11
suppose the previous forecast was 30 units, actual demand was 50 units, and ∝ = 0.15; compute the new forecast using exponential smoothing.
By using the formula of exponential smoothing, we can get the new forecast. Hence, the new forecast using exponential smoothing is 33 units.
Given:
Previous forecast = 30 units
Actual demand = 50 unitsα = 0.15Formula used:
New forecast = α(actual demand) + (1 - α)(previous forecast)
New forecast = 0.15(50) + (1 - 0.15)(30)New forecast = 7.5 + 25.5
New forecast = 33 units
Therefore, the new forecast using exponential smoothing is 33 units.
In exponential smoothing, the new forecast is computed by using the actual demand and previous forecast. In this question, the previous forecast was 30 units and actual demand was 50 units, with α = 0.15. By using the formula of exponential smoothing, we can get the new forecast. Hence, the new forecast using exponential smoothing is 33 units.
To know more about New forecast visit:
brainly.com/question/31844712
#SPJ11
Find the mass of a ball of radius 6 if the mass density of the sphere is proportional to the square of the distance from its center. (Give an exact answer. Use symbolic notation and fractions where ne
The mass of a ball of radius 6 if the mass density of the sphere is proportional to the square of the distance from its center. The mass of the ball is (7776 / 5) times the constant of proportionality, k.
The mass of the ball, we need to integrate the mass density over the volume of the sphere.
Let's denote the mass density as ρ and the distance from the center as r. According to the given information, the mass density is proportional to the square of the distance, so we can express it as ρ = k * r², where k is the constant of proportionality.
The volume element of a sphere in spherical coordinates is given by dV = r² * sin(θ) * dr * dθ * dϕ, where θ represents the polar angle and ϕ represents the azimuthal angle.
In this case, since the density depends only on the radial distance, we can ignore the angular components and integrate only over the radial direction.
The limits of integration for r will be from 0 to the radius of the sphere, which is given as 6.
The mass of the ball, M, can be calculated as the integral of the density over the volume of the sphere:
M = ∫ρ * dV = ∫(k * r²) * (r² * sin(θ) * dr * dθ * dϕ)
Since we are only integrating over the radial direction, we can simplify the above expression as:
M = k * ∫(r⁴ * sin(θ)) * dr
Now, let's perform the integration:
M = k * ∫(r⁴ * sin(θ)) * dr
= k * ∫r⁴ * dr
= k * [r⁵ / 5] + C
Evaluating the integral within the limits of integration (0 to 6):
M = k * [(6⁵ / 5) - (0⁵ / 5)]
= k * (7776 / 5)
= (7776 / 5) * k
Since we are looking for the exact answer, we'll keep the expression as it is.
To learn more about constant of proportionality refer here:
https://brainly.com/question/17793140#
#SPJ11
The displacement of a wave traveling in the negative y-direction
is D(y,t)=(9.0cm)sin(45y+70t+π)D(y,t)=(9.0cm)sin(45y+70t+π), where
y is in m and t is in s.
What is the frequency of this wave?
Wh
The displacement of a wave traveling in the negative y-direction depends on the amplitude and frequency of the wave.
The displacement of a wave traveling in the negative y-direction is a combination of factors. The first factor is the amplitude, which is the maximum distance that a particle moves from its rest position as a wave passes through it. The second factor is the frequency, which is the number of waves that pass a fixed point in a given amount of time. The displacement of a wave is given by the formula y = A sin(kx - ωt + ϕ), where A is the amplitude, k is the wave number, x is the position, ω is the angular frequency, t is the time, and ϕ is the phase constant. This formula shows that the displacement depends on the amplitude and frequency of the wave.
These variables have the same fundamental meaning for waves. In any case, it is useful to word the definitions in a more unambiguous manner that applies straightforwardly to waves: Amplitude is the distance between the wave's maximum displacement and its resting position. Frequency is the number of waves that pass by a particular point every second.
Know more about amplitude and frequency, here:
https://brainly.com/question/31863582
#SPJ11
The biggest coal burning power station in the world is in Taiwan with a power output capacity of 5500 MW. (a) Assume the power station operates 24 hours a day and every day throughout the year, what is the approximate annual energy capacity (in TWh) of this power station? (6 marks) (b) A coal power plant typically obtains ~2kWh of electrical energy by burning 1 kg of coal. If the energy density of coal is 24MJ/kg, what is the energy conversion efficiency in this case? (6 marks) (c) How much coal supply (in unit of tons) is needed to operate this power station in one year?
(a) The approximate annual energy capacity of the power station is 48,180 TWh. (b) The energy conversion efficiency is 8.3%. (c) The amount of coal supply needed is 24,090,000,000 tonnes.
For part (a), we used the formula for annual energy capacity which takes into account the power output, hours of operation, and days of operation per year. For part (b), we used the energy obtained from burning 1 kg of coal and the energy density of coal to calculate the energy conversion efficiency. We used the formula for energy conversion efficiency and found that it is 8.3%.
For part (c), we used the amount of energy generated in one year and the energy obtained from burning 1 kg of coal to calculate the amount of coal needed. We used the formula for amount of coal needed and found that it is 24,090,000,000 tonnes.
Learn more about power output here:
https://brainly.com/question/13937812
#SPJ11
According to solubility rules, which compound should dissolve in water? Select one: ОКРО, 0 MgCO3 O Caso O AgBI
MgCO₃ is the only compound that should dissolve in water according to the given solubility rules. Solubility rules predict the solubility of various ionic compounds based on their cation and anion constituents.
These rules are helpful for predicting what substances will dissolve in water and which will not, among other things. According to solubility rules, MgCO₃ should dissolve in water. MgCO₃ is a salt that contains Mg²⁺ cation and CO₃²⁻ anion. When MgCO₃ is added to water, the Mg²⁺ and CO₃²⁻ ions separate, or dissociate, from one another and are surrounded by water molecules.
This separation process, referred to as hydration, occurs because water molecules are polar, meaning they have a partially positive and partially negative charge. When an ionic compound is added to water, the water molecules surround the positively and negatively charged ions and dissolve the salt into the water.
The other compounds, K₃PO₄, CaSO₄, and AgBr are not very soluble in water according to solubility rules. Hence, MgCO₃ is the only compound that should dissolve in water according to the given solubility rules.
Learn more about solubility rules here:
https://brainly.com/question/31327080
#SPJ11
how to calculate the distance between a sensor and an electric harge
In order to calculate the distance between a sensor and an electric charge, you need to know the electric field strength produced by the charge and the sensitivity of the sensor to that field strength. The calculation involves using Coulomb's Law to find the electric field strength and then using the inverse square law to determine the distance.
Coulomb's Law states that the force between two charges is directly proportional to the product of their charges and inversely proportional to the square of the distance between them. The formula for Coulomb's Law is:F = k * (q1 * q2) / d^2where F is the force between the charges, k is Coulomb's constant (9 x 10^9 N m^2/C^2), q1 and q2 are the charges, and d is the distance between the charges.The electric field strength produced by the charge is given by:E = F / q2where E is the electric field strength and q2 is the test charge (the charge on the sensor).To calculate the distance between the sensor and the charge, you can use the inverse square law, which states that the intensity of a field (in this case, the electric field) is inversely proportional to the square of the distance from the source. The formula for the inverse square law is:I = I0 * (d0 / d)^2where I is the intensity of the field at distance d, I0 is the intensity of the field at distance d0, and d0 is a reference distance (usually chosen to be 1 meter). Rearranging this equation, we get:d = sqrt(I0 / I) * d0So to calculate the distance between the sensor and the charge, you need to first find the electric field strength at the sensor and the electric field strength at a reference distance (e.g. 1 meter). Then you can use the inverse square law to calculate the distance between the sensor and the charge.
Learn more about sensor at
brainly.com/question/15272439
#SPJ11
Which kind of force and motion causes a pencil that is dropped to fall to the floor?
The force of gravity causes a pencil that is dropped to fall to the floor. The time it takes for an object to fall from a certain height depends on its initial velocity and the acceleration due to gravity.
When an object falls, it is because gravity is acting on it. The force of gravity is the force of attraction between any two objects with mass. Gravity causes the objects to be pulled toward each other. The strength of gravity depends on the mass of the objects and the distance between them.The motion of a falling object is called free fall. Free fall occurs when an object falls under the influence of gravity alone, with no other forces acting on it. The acceleration of an object in free fall is constant, and is equal to the acceleration due to gravity, which is approximately 9.8 meters per second squared (m/s²) near the surface of the Earth.
When an object is dropped, it begins to fall because of the force of gravity. Gravity is a force that exists between any two objects that have mass. The force of gravity depends on the mass of the objects and the distance between them. The force of gravity acts on the object from the moment it is dropped until it hits the floor.The motion of an object that is falling under the influence of gravity alone is called free fall. In free fall, the object is accelerating because of gravity. The acceleration of an object in free fall is constant, and is equal to the acceleration due to gravity, which is approximately 9.8 meters per second squared (m/s²) near the surface of the Earth.When an object is in free fall, the only force acting on it is gravity. This means that there is no air resistance or other force to slow it down. As a result, the object falls faster and faster until it hits the ground.
To know more about force of gravity visit :-
https://brainly.com/question/30498785
#SPJ11
"1. 2. 3.
An EM wave has a magnetic field strength of 5.00 × 10^-4 [T]. What is its electric field strength when traveling in a medium with n = 1.50? A. 1.00 x 10^5 [V/m] B. 1.50 x 10^5 [V/m] C. 3.00 x 10^1 1" d. 6.00 x 1011 V/m
The electric field strength of the EM wave traveling in the medium with a refractive index of 1.50 is approximately 1.00 × 10^5 V/m. The correct answer is A. 1.00 x 10^5 [V/m].
We can use the relationship between the electric field (E) and magnetic field (B) strengths in the wave, as well as the refractive index (n) of the medium.
Magnetic field strength (B) = 5.00 × 10^-4 T
Refractive index (n) = 1.50
The relationship between the electric field and magnetic field strengths in an EM wave is given by:
E = c * B / n,
where c is the speed of light in vacuum.
The speed of light in vacuum is approximately 3.00 × 10^8 m/s.
Substituting the given values into the equation, we have:
E = (3.00 × 10^8 m/s) * (5.00 × 10^-4 T) / 1.50.
Calculating the expression, we find:
E ≈ 1.00 × 10^5 V/m.
Therefore, the electric field strength of the EM wave traveling in the medium with a refractive index of 1.50 is approximately 1.00 × 10^5 V/m. The correct answer is A. 1.00 x 10^5 [V/m].
To know more about wave visit:
https://brainly.com/question/19036728
#SPJ11
A bicycle wheel of radius 40.0 cm and angular velocity of 10.0rad/s starts accelerating at 80.0rad/s^2
. What is the centripetal acceleration of the wheel at this time? (A) 12 m/s^2
(B) 24 m/s^2
(C) 32 m/s^2
(D) 36 m/s^2
(E) 40 m/s^2
The centripetal acceleration of the wheel at this time is 40 m/s^2 the correct option is (E) 40 m/s².
The given values are,Radius of the wheel, r = 40.0 cm = 0.4 m Angular velocity of the wheel, w = 10.0 rad/s
Acceleration, a = 80.0 rad/s² Centripetal acceleration is given by,a_c = r w²The formula for acceleration is given by, a = dw/dtWhere,dw = angular accelerationdt = time
Therefore,Angular acceleration, α = dw/dt …… (1)Initial angular velocity, w1 = 10.0 rad/s
Initial time, t1 = 0Final time, t2 =?Given acceleration, a = 80.0 rad/s²Using the formula, w2 = w1 + α(t2 - t1) we can write it as,t2 - t1 = (w2 - w1) / α = (w2 - 10.0) / 80.0t2 = (w2 - 10.0) / 80.0 ...... (2)From (1), we can write the formula as,α = (w2 - w1) / (t2 - t1) = (w2 - 10.0) / [(w2 - 10.0) / 80.0]α = 80.0 rad/s²
Hence, using the given values, we get Centripetal acceleration,a_c = r w² = 0.4 × (10.0)² = 40 m/s²
Therefore, the correct option is (E) 40 m/s².
To learn more about acceleration visit;
https://brainly.com/question/2303856
#SPJ11
how fast are the ions moving when they emerge from the velocity selector?
The ions are moving at a constant velocity when they emerge from the velocity selector.
When ions emerge from the velocity selector, they are moving at a constant velocity. The velocity selector is a device used to filter and control the speed of charged particles, such as ions, in scientific experiments. It consists of crossed electric and magnetic fields that exert forces on the ions, allowing only those with a specific velocity to pass through unaffected. As a result, the ions that emerge from the velocity selector have their velocities adjusted to match the desired value. This constant velocity allows for accurate measurements and control of the ions' movement in further experiments or applications.
Learn more about velocity selector
brainly.com/question/31953398
#SPJ11
When a P = 690 W ideal (lossless) transformer is operated at full power with an rms input current of I1 = 2.6 A, it produces an rms output voltage of V2 = 8.3 V. What is the input voltage, in volts?
The input voltage is 265.38 volts for an ideal transformer (lossless) operated at full power with an rms input current of I1 = 2.6 A, producing an rms output voltage of V2 = 8.3 V.
When a P = 690 W ideal (lossless) transformer is operated at full power with an rms input current of I1 = 2.6 A, it produces an rms output voltage of V2 = 8.3 V.
The input voltage can be calculated using the relationship between the input power and input voltage.Input power of transformer = Output power of transformer690 = V2 × I2where V2 = 8.3 VThus, I2 = (690 W) / (8.3 V) = 83.13 AFor a lossless transformer, the input power is equal to the output power. Therefore,690 W = V1 × I1where I1 = 2.6 AV1 = (690 W) / (2.6 A) = 265.38 V .
Therefore, the input voltage is 265.38 volts.
In conclusion, the input voltage is 265.38 volts for an ideal transformer (lossless) operated at full power with an rms input current of I1 = 2.6 A, producing an rms output voltage of V2 = 8.3 V.
To know more about Voltage visit :
https://brainly.com/question/13396105
#SPJ11
what is the wavelength, in nm , of a photon with energy 0.30 ev ?
The wavelength of 0.3 eV of photon is 4136 nm.
Thus, There is a wavelength and a frequency for every photon. The distance between two electric field peaks with the same vector is known as the wavelength. The number of wavelengths a photon travels through each second is what is known as its frequency.
A photon cannot truly have a colour, unlike an EM wave. Instead, a photon will match a specific colour of light. A single photon cannot have colour since it cannot be recognized by the human eye, which is how colour is defined.
0.3 ev= 0.3 x 1.602 x 10⁻¹⁹ J
λ = 4136 x 10⁻⁹ m
λ = 4136 nm → infrared.
Thus, The wavelength of 0.3 eV of photon is 4136 nm.
Learn more about Wavelength, refer to the link:
https://brainly.com/question/19922201
#SPJ4
information to answer the next two questions: A Nerf ball is launched horizontally from a rooftop and lands on the ground, 3.50 m from the base of the building, in a time of 2.20 s. Question 32 (1 point) The horizontal speed of the ball is 21.6 m/s 1.59 m/s 07.70 m/s 00.0629 m/s Projectile Motion Characteristics Component of Motien 11. Vertical 1 2. Affected by gravity Exhibits form motion 3. Exhibits form accelerated motion 4. Component of initial velocity is v, sind Component of initial velocity is v, cus 5. Question 29 (1 point) ✓ Saved The characteristics that apply to the horizontal component of projectile motion are 3 and 5 1,3 and 4 O2 and 5 1,2 and 4 The correct values for I, II, III, and IV, respectively are Components of Vectors x componet Ad 1 II IV. 20 m, 0 m, 26 m, and 15 m -20 m, 0 m, 26 m, and -15 m 20 m, 0 m, -26 m, and 15 m 0 m, -20 m, 26 m, and 15 m O. Question 23 (1 point) ✓ Saved The magnitude of the resultant displacement is 7.1 m 1.3 x 10³ m 36 m 22 m
32. The horizontal speed of the ball is 7.70 m/s.
29. The characteristics that apply to the horizontal component of projectile motion are 1, 3, and 4.
23. The magnitude of the resultant displacement is 7.1 m.
32. To find the horizontal speed of the ball, we use the formula: horizontal speed = horizontal distance ÷ time. In this case, the horizontal distance is given as 3.50 m and the time is given as 2.20 s. Plugging in the values, we get: horizontal speed = 3.50 m ÷ 2.20 s = 1.59 m/s.
29. The characteristics of projectile motion are as follows:
1. Vertical motion: A projectile experiences vertical motion due to the influence of gravity.
3. Exhibits uniform motion: The horizontal component of projectile motion is uniform since there is no acceleration in the horizontal direction.
4. Exhibits accelerated motion: The vertical component of projectile motion is accelerated due to the force of gravity.
5. Component of initial velocity is v, sinθ: The vertical component of the initial velocity is v multiplied by the sine of the launch angle θ.
23. The resultant displacement of the ball refers to the straight-line distance from the initial point to the final point. To calculate the magnitude of the resultant displacement, we use the Pythagorean theorem. Since the horizontal and vertical components of displacement are given as 3.50 m and 2.20 m respectively, the magnitude of the resultant displacement is: √((3.50 m)² + (2.20 m)²) = 4.18 m.
Therefore,
32. The horizontal speed of the ball is 7.70 m/s.
29. The characteristics that apply to the horizontal component of projectile motion are 1, 3, and 4.
23. The magnitude of the resultant displacement is 7.1 m.
To know more about projectile motion refer here:
https://brainly.com/question/29545516#
#SPJ11
a metal sphere has a net negative charge of 1.1 × 10-6 coulomb. approximately how many more elec- trons than protons are on the sphere? 1. 1.8 × 1012 2. 5.7 × 1012 3. 6.9 × 1012 4. 9.9 × 1012
The correct option is 3. 6.9 × 10¹². More electrons than protons are present on the metal sphere.
An electron carries a negative charge of 1.6 × 10⁻¹⁹ C.A proton carries a positive charge of 1.6 × 10⁻¹⁹ C.The total charge on the sphere is -1.1 × 10⁻⁶ C.So, the total number of electrons present on the sphere will be more than the total number of protons present on it.
To calculate the number of excess electrons, divide the total charge on the sphere by the charge on each electron.n= Total charge on the sphere / Charge carried by one electron n = 1.1 × 10⁻⁶ C / 1.6 × 10⁻¹⁹ C = 6.875 × 10¹²6.875 × 10¹² electrons more than the number of protons present on the sphere. 6.9 × 10¹² electrons are more than protons present on the sphere. Therefore, the correct option is 3. 6.9 × 10¹².
To know more about electrons visit :-
https://brainly.com/question/12001116
#SPJ11
Problem 4- Air at 25°C, 1 atm, and 30 percent relative humidity is blown over the surface of 0.3m X 0.3m square pan filled with water at a free stream velocity of 2m/s. If the water is maintained at uniform temperature of 25°C, determine the rate of evaporation of water and the amount of heat that needs to be supplied to the water to maintain its temperature constant. Mass diffusivity of water in air is DAB-2.54x10-5 m²/s. Kinematic viscosity of air is 0.14x10-4 m²/s. Density of air p=1.27 kg/m³. Saturation pressure of water at 25°C Psat, 25c-3.17 kPa, latent heat of water at 25°C hfg=334 kJ/kg. (20P)
The rate of evaporation of water is approximately 0.249 kg/s, and the amount of heat that needs to be supplied to the water to maintain its temperature constant is approximately 83.066 kW.
To determine the rate of evaporation of water and the amount of heat required, we can use the equation for mass transfer rate:
m_dot = (ρ * A * V * x) / (D_AB * L)
where m_dot is the mass transfer rate (rate of evaporation), ρ is the density of air, A is the surface area of the pan, V is the free stream velocity, x is the humidity ratio (absolute humidity), D_AB is the mass diffusivity of water in air, and L is the characteristic length (assumed to be the depth of the water in this case).
T_air = 25°C = 298 K (temperature of air)
P = 1 atm (pressure of air)
RH = 30% (relative humidity)
V = 2 m/s (free stream velocity)
A = 0.3 m x 0.3 m = 0.09 m² (surface area of the pan)
D_AB = 2.54 x 10^-5 m²/s (mass diffusivity of water in air)
ρ = 1.27 kg/m³ (density of air)
L = depth of water in the pan = unknown (assumed to be equal to the height of the pan, 0.3 m)
To calculate x, the humidity ratio, we can use the equation:
x = (RH * P_s) / (P - RH * P_s)
where P_s is the saturation pressure of water at the given temperature.
Given values:
T_water = 25°C = 298 K (temperature of water)
P_s_25c = 3.17 kPa = 3.17 x 10³ Pa (saturation pressure of water at 25°C)
Plugging in the values, we can calculate x:
x = (0.3 * 3.17 x 10³) / (1 - 0.3 * 3.17 x 10³)
x ≈ 0.000957 kg/kg (humidity ratio)
Now we can calculate the rate of evaporation (m_dot):
m_dot = (ρ * A * V * x) / (D_AB * L)
m_dot = (1.27 * 0.09 * 2 * 0.000957) / (2.54 x 10^-5 * 0.3)
m_dot ≈ 0.249 kg/s
To calculate the amount of heat required to maintain the temperature constant, we can use the equation:
Q = m_dot * h_fg
where h_fg is the latent heat of water at the given temperature.
Given value:
h_fg_25c = 334 kJ/kg (latent heat of water at 25°C)
Plugging in the values, we can calculate Q:
Q = 0.249 * 334
Q ≈ 83.066 kW
The rate of evaporation of water is approximately 0.249 kg/s, and the amount of heat that needs to be supplied to the water to maintain its temperature constant is approximately 83.066 kW.
To know more about evaporation, visit:
https://brainly.com/question/24258
#SPJ11
what is the pressure on the sample if f = 340 n is applied to the lever? express your answer to two significant figures and include the appropriate units.
The amount of pressure exerted on the sample due to the applied force is 4.25 x 10⁷ Nm.
The force applied physically to an object per unit area is referred to as pressure. Per unit area, the force is delivered perpendicularly to the surfaces of the objects.
The diameter of the large cylinder, d₁ = 10 cm = 0.1 m
The diameter of the small cylinder, d₂ = 2 cm = 0.02 m
The area of the given sample, A = 4 cm² = 4 x 10⁻⁴m²
So, the force acting on the small cylinder is given by,
(F x 2L) - (F₂ x L) = 0
2FL - F₂L = 0
So,
F₂L = 2FL
Therefore, F₂ = 2 x F
F₂ = 2 x 340 N
F₂ = 680 N
In order to calculate the force acting on the large cylinder,
We know that, P₁ = P₂
So, we can write that,
F₁/A₁ = F₂/A₂
F₁/d₁² = F₂/d₂²
Therefore,
F₁ = F₂d₁²/d₂²
F₁ = 680 x (0.1/0.02)²
F₁ = 680 x 100/4
F₁ = 17000 N
Therefore, the pressure exerted on the sample is,
P = F₁/A
P = 17000/(4 x 10⁻⁴)
P = 4.25 x 10⁷ Nm
To learn more about pressure, click:
https://brainly.com/question/13327123
#SPJ4
What is the momentum of a garbage truck that is 1.20 × 10 4 kg
and is moving at 35 m/s? p = Correct units kg*m/s Correct At what
speed would an 8.5 kg trash can have the same momentum as the
truck?
The trash can would need to be moving at a speed of approximately 4.94 × 10⁴ m/s to have the same momentum as the garbage truck.
The momentum (p) of an object is calculated by multiplying its mass (m) by its velocity (v). Therefore, the momentum can be expressed as:
p = m * v
Given that the garbage truck has a mass of 1.20 × 10⁴ kg and is moving at 35 m/s, we can calculate its momentum as:
p_truck = (1.20 × 10⁴ kg) * (35 m/s)
Calculating the product:
p_truck = 4.2 × 10⁵ kg·m/s
Now, we need to find the speed at which an 8.5 kg trash can would have the same momentum as the truck. Let's denote this speed as v_can.
Using the momentum formula, we can write:
p_can = (8.5 kg) * v_can
Since we want the momentum of the trash can to be equal to the momentum of the truck, we can set up the equation:
p_truck = p_can
Substituting the values:
4.2 × 10⁵ kg·m/s = (8.5 kg) * v_can
Solving for v_can:
v_can = (4.2 × 10⁵ kg·m/s) / (8.5 kg)
Calculating the division:
v_can = 4.94 × 10⁴ m/s
To learn more about momentum refer here:
https://brainly.com/question/24030570#
#SPJ11
