Answer:
Pressure is more in the open container than the closed one.
Explanation:
The pressure due to the fluid at a depth is given by
Pressure = depth x density of fluid x gravity
So, when the container is open, the atmospheric pressure is also add up but when the container is closed only the pressure due to the fluid is there.
So, when the container is open, the pressure is atmospheric pressure + pressure due to the fluid.
hen the container is closed only the pressure due to the fluid is there.
A particle of mass 1.2 mg is projected vertically upward from the ground with a velocity of 1.62 x 10 cm/h. Use the above information to answer the following four questions: 7. The kinetic energy of the particle at time t = 0 s is A. 1.215 x 10-3 J B. 2.430 J C. 1215 J D. 9.72 x 106 J E. OJ (2)
Answer:
K = 0 J
Explanation:
Given that,
The mass of the particle, m = 1.2 mg
The speed of the particle, [tex]v=1.62\times 10\ cm/h[/tex]
We need to find the kinetic energy of the particle at time t = 0 s.
At t = 0 s, the particle is at rest, v = 0
So,
[tex]K=\dfrac{1}{2}mv^2[/tex]
If v = 0,
[tex]K=0\ J[/tex]
So, the kinetic energy of the particle at time t = 0 s is 0 J.
g As they reach higher temperatures, most semiconductors... Selected Answer: have an increased resistance. Answers: have a constant resistance. have an increased resistance. have a decreased resistance.
Answer:
have an increased resistance
The north pole of magnet A will __?____ the south pole of magnet B
Answer:
A will attract
B will repare
Two plastic bowling balls, 1 and 2, are rubbed with cloth until they each carry a uniformly distributed charge of magnitude 0.50 nC . Ball 1 is negatively charged, and ball 2 is positively charged. The balls are held apart by a 900-mm stick stuck through the holes so that it runs from the center of one ball to the center of the other.
Required:
What is the magnitude of the dipole moment of the arrangement?
Answer:
The right solution is "[tex]4.5\times 10^{-10} \ Cm[/tex]".
Explanation:
Given that,
q = 0.50 nC
d = 900 mm
As we know,
⇒ [tex]P=qd[/tex]
By putting the values, we get
⇒ [tex]=0.50\times 900[/tex]
⇒ [tex]=(0.50\times 10^{-9})\times 0.9[/tex]
⇒ [tex]=4.5\times 10^{-10} \ Cm[/tex]
Answer:
The dipole moment is 4.5 x 10^-10 Cm.
Explanation:
Charge on each ball, q = 0.5 nC
Length, L = 900 mm = 0.9 m
The dipole moment is defined as the product of either charge and the distance between them.
It is a vector quantity and the direction is from negative charge to the positive charge.
The dipole moment is
[tex]p = q L\\\\p = 0.5 \times 10^{-9}\times 0.9\\\\p = 4.5\times 10^{-10} Cm[/tex]
When a rigid body rotates about a fixed axis, all the points in the body have the same Group of answer choices linear displacement. angular acceleration. centripetal acceleration. tangential speed. tangential acceleration.
Answer:
angular acceleration.
Explanation:
Newton's law of universal gravitation states that the force of attraction (gravity) acting between the Earth and all physical objects is directly proportional to the Earth's mass, directly proportional to the physical object's mass and inversely proportional to the square of the distance separating the Earth's center and that physical object.
Generally, when a rigid body is made to rotate about a fixed axis, all the points in the body would typically have the same angular acceleration, angular displacement, and angular speed.
A body of mass 4kg is moving with a velocity of 108km/h . find the kenetic energy of the body.
Answer:
KE = 2800 J
Explanation:
Usually a velocity is expressed as m/s. Then the energy units are joules.
[tex]\frac{108 km}{hr} * \frac{1000m}{1 km} * \frac{1 hour}{3600 seconds} =\frac{108*1000 m}{3600sec}[/tex]
v = 30 m / sec
KE = 1/2 * 4 * (30)^2
KE =2800 kg m^2/sec^2
KE = 2800 Joules
A tire is filled with air at 22oC to a gauge pressure of 240 kPa. After driving for some time, if the temperature of air inside the tire is 45oC, what fraction of the original volume of air must be removed to maintain the pressure at 240 kPa?
Answer:
7.8% of the original volume.
Explanation:
From the given information:
Temperature [tex]T_1[/tex] = 22° C = 273 + 22 = 295° C
Pressure [tex]P_1[/tex] = 240 kPa
Temperature [tex]T_2[/tex] = 45° C
At initial temperature and pressure:
Using the ideal gas equation:
[tex]P_1V_1 =nRT_1[/tex]
making V_1 (initial volume) the subject:
[tex]V_1 = \dfrac{nRT_1}{P_1}[/tex]
[tex]V_1 = \dfrac{nR*295}{240}[/tex]
Provided the pressure maintained its rate at 240 kPa, when the temperature reached 45° C, then:
the final volume [tex]V_2[/tex] can be computed as:
[tex]V_2 = \dfrac{nR*318}{240}[/tex]
Now, the change in the volume ΔV = V₂ - V₁
[tex]\Delta V = \dfrac{nR*318}{240}- \dfrac{nR*295}{240}[/tex]
[tex]\Delta V = \dfrac{23nR}{240}[/tex]
∴
The required fraction of the volume of air to keep up the pressure at (240) kPa can be computed as:
[tex]= \dfrac{\dfrac{23nR}{240}}{ \dfrac{295nR}{240}}[/tex]
[tex]= {\dfrac{23nR}{240}} \times { \dfrac{240}{295nR}}[/tex]
[tex]= 0.078[/tex]
= 7.8% of the original volume.
When you hammer a nail into wood, the nail heats up. 30 Joules of energy was absorbed by a 5-g nail as it was hammered into place. How much does the nail's temperature increase (in °C) during this process? (The specific heat capacity of the nail is 450 J/kg-°C, and round to 3 significant digits.
Answer:
13.33 K
Explanation:
Given that,
Heat absorbed, Q = 30 J
Mass of nail, m = 5 g = 0.005 kg
The specific heat capacity of the nail is 450 J/kg-°C.
We need to find the increase in the temperature during the process. The heat absorbed in a process is as follows:
[tex]Q=mc\Delta T\\\\\Delta T=\dfrac{Q}{mc}\\\\\Delta T=\dfrac{30}{0.005\times 450}\\\\=13.33\ K[/tex]
So, the increase in temperature is 13.33 K.
A student claimed that thermometers are useless because a
thermometer always registers its own temperature. How would you
respond?
[
Explain what a circuit breaker is and how it helps protect your house?
Explanation:
A circuit breaker is an electrical switch designed to protect an electrical circuit from damage caused by overcurrent/overload or short circuit. Its basic function is to interrupt current flow after protective relays detect a fault.
Circuit breakers have been designed to detect when there is a fault in the electricity, so it will “trip” and shut down electrical flow. ... This detection is key to preventing surges of electricity that travel to appliances or other outlets, which can cause them to break down
Hi can someon help me how to answer this?
Btw I'm from Philippines
Answer:
Test 1
1.True
2.True
3.True
4.False
5.True
6.True
7.False
8.True
9.True
10.True
yung iba nasa pic
An object is 2.0 cm from a double convex lens with a focal length of 1.5 cm. Calculate the image distance
Answer:
0.857 cm
Explanation:
We are given that:
The focal length for a convex lens to be (f) = 1.5cm
The object distance (u) = - 2.0 cm
We are to determine the image distance (v) = ??? cm
By applying the lens formula:
[tex]\dfrac{1}{f} = \dfrac{1}{u}+\dfrac{1}{v}[/tex]
By rearrangement and making (v) the subject of the above formula:
[tex]v = \dfrac{uf}{u-f}[/tex]
replacing the given values:
[tex]v = \dfrac{(-2.0)(1.5)}{(-2.0 -1.5)}[/tex]
[tex]v = \dfrac{-3.0}{(-3.5)}[/tex]
v = 0.857 cm
In the following calculations, be sure to express the answer in standard scientific notation with the appropriate number of
significant figures.
3.88 x 1079 - 4.701 x 1059
x 10
g
Answer:
-45,597.07
Explanation:
if not in scientific calculator and yung answer nung sa scientific sa comment na lang dinadownload ko ka eh
A submarine has a "crush depth" (that is, the depth at which
water pressure will crush the submarine) of 400 m. What is
the approximate pressure (water plus atmospheric) at this
depth? (Recall that the density of seawater is 1025 kg/m3, g=
9.81 m/s2, and 1 kg/(m-s2) = 1 Pa = 9.8692 x 10-6 atm.)
Answer:
P =40.69 atm
Explanation:
We need to find the approximate pressure at a depth of 400 m.
It can be calculated as follows :
P = Patm + ρgh
Put all the values,
[tex]P=1\ atm+1025 \times 9.81\times 400\times 9.8692\times 10^{-6}\ atm/Pa\\\\P=40.69\ atm[/tex]
So, the approximate pressure is equal to 40.69 atm.
A body initially at rest travels a distance 100 m in 5 s with a constant acceleration. calculate
(i) Acceleration
(ii) Final velocity at the end of 5 s.
Answer:
(i)8m/s²(ii)40m/s
Explanation:
according to the formula
½at²=s.
then substituting the data
½a•5²=100
a=8m/s²
v=at=8•5=40m/s
Answer:
(I)
[tex]{ \bf{s = ut + \frac{1}{2} a {t}^{2} }} \\ 100 = (0 \times 5) + \frac{1}{2} \times a \times {5}^{2} \\ 200 = 25a \\ { \tt{acceleration = 8 \: m {s}^{ -2} }}[/tex]
(ii)
[tex]{ \bf{v = u + at}} \\ v = 0 + (8 \times 5) \\ { \tt{final \: velocity = 40 \: m {s}^{ - 1} }}[/tex]
What is significant about the primary colors of pigments?
They can be mixed together to make almost any other color.
Any two primary colors of pigments combine to make white pigment.
Each primary color of pigment absorbs all other colors.
Any two primary colors of pigments combine to make black pigment.
Answer:
They can be mixed together to make almost any other color.
Explanation:
All the three primary colors can mix to form white color.
Blue and red mix to form a black color.
When a golfer tees off, the head of her golf club which has a mass of 158 g is traveling 48.2 m/s just before it strikes a 46.0 g golf ball at rest on a tee. Immediately after the collision, the club head continues to travel in the same direction but at a reduced speed of 32.7 m/s. Neglect the mass of the club handle and determine the speed of the golf ball just after impact.
Answer:
v₂ = 53.23 m/s
Explanation:
Given that,
The mass of a golf club, m₁ = 158 g = 0.158 kg
The initial speed of a golf club, u₁ = 48.2 m/s
The mass of a golf ball, m₂ = 46 g = 0.046 kg
It was at rest, u₂ = 0
Immediately after the collision, the club head continues to travel in the same direction but at a reduced speed of 32.7 m/s, v₁ = 32.7 m/s
We use the conservation of energy to find the speed of the golf ball just after impact as follows :
[tex]m_1u_1+m_2u_2=m_1v_1+m_2v_2\\\\v_2=\dfrac{m_1u_1-m_1v_1}{m_2}\\\\v_2=\dfrac{0.158(48.2)-0.158(32.7)}{0.046}\\\\=53.23\ m/s[/tex]
So, the speed of the golf ball just after the impact is equal to 53.23 m/s.
A hot air balloon is a sphere of volume 2210 m3. The density of the hot air inside is 1.13 kg/m3, while the air outside has a density of 1.29 kg/m3. The balloon itself has a mass of 240 kg. What is the TOTAL NET force acting on the balloon?
[?]N
The total net force acting on the balloon will be 24498 Newtons
Given that
Volume of the balloon = 2210 cubic meter
Density of the air inside the balloon = 1.13 kg/m3
What will be the net force exerted on the balloon ?Here force on the balloon will be equal to the weight of the air displaced by balloon
[tex]F= mass of air displaced\times gravity[/tex]
[tex]F= Density \times volume \times gravity[/tex]
[tex]F=1.13 \times 2210 \times 9.81[/tex]
[tex]F=24498 N[/tex]
The total net force acting on the balloon will be 24498 Newtons
To know more about buoyancy force follow
https://brainly.com/question/117714
a vechile having a mass of 500kg is moving with a speed of 10m/s.Sand is dropped into it at the rate of 10kg/min.What force is needed to keep the vechile moving with uniform speed
Answer:
1.67 N
Explanation:
Applying,
F = u(dm/dt)+m(du/dt)................ Equation 1
Where F = force, m = mass of the vehicle, u = speed.
Since u is constant,
Therefore, du/dt = 0
F = u(dm/dt)............... Equation 2
From the question,
Given: u = 10 m/s, dm/dt = 10 kg/min = (10/60) kg/s
Substitute these values into equation 2
F = 10(10/60)
F = 100/60
F = 1.67 N
A 64-ka base runner begins his slide into second base when he is moving at a speed of 3.2 m/s. The coefficient of friction between his clothes and Earth is 0.70. He slides so that his speed is zero just as he reaches the base.
Required:
a. How much mechanical energy is tout due to friction acting on the runner?
b, How far does he slide?
Answer:
Explanation:
From the given information:
mass = 64 kg
speed = 3.2 m/s
coefficient of friction [tex]\mu =[/tex] 0.70
The mechanical energy touted relates to the loss of energy in the system as a result of friction and this can be computed as:
[tex]W = \Delta K.E[/tex]
[tex]\implies \dfrac{1}{2}m(v^2 -u^2)[/tex]
[tex]= \dfrac{1}{2}(64.0 \kg) (0 - (3.2 \ m/s^2))[/tex]
Thus, the mechanical energy touted = 327.68 J
According to the formula used in calculating the frictional force
[tex]F_r = \mu mg[/tex]
= 0.70 × 64 kg× 9.8 m/s²
= 439.04 N
The distance covered now can be determined as follows:
d = W/F
d = 327.68 J/ 439.04 N
d = 0.746 m
PLEASE HELP ME WITH THIS ONE QUESTION
The half-life of Barium-139 is 4.96 x 10^3 seconds. A sample contains 3.21 x 10^17 nuclei. How much of the sample is left after 1.98 x 10^4 seconds?
[tex]A=2.01×10^{16}\:\text{nuclei}[/tex]
Explanation:
Given:
[tex]\lambda = 4.96×10^3 s[/tex]
[tex]A_0 = 3.21x10^{17}[/tex] nuclei
t = 1.98×10^4 s
[tex]A=A_02^{-\frac{t}{\lambda}}[/tex]
[tex]A=(3.21×10^{17}\:\text{nuclei}) \left(2^{-\frac{1.98×10^4}{4.96×10^3}} \right)[/tex]
[tex]\:\:\:\:\:\:\:=2.01×10^{16}\:\text{nuclei}[/tex]
A typical incandescent light bulb consumes 75 W of power and has a mass of 20 g. You want to save electrical energy by dropping the bulb from a height great enough so that the kinetic energy of the bulb when it reaches the floor will be the same as the energy it took to keep the bulb on for 2.0 hours. From what height should you drop the bulb, assuming no air resistance and constant g?
Answer:
h = 2755102 m = 2755.102 km
Explanation:
According to the given condition:
Potential Energy = Energy Consumed by Bulb
[tex]mgh = Pt\\\\h = \frac{Pt}{mg}[/tex]
where,
h = height = ?
P = Power of bulb = 75 W
t = time = (2 h)(3600 s/1 h) = 7200 s
m = mass of bulb = 20 g = 0.02 kg
g = acceleration due to gravity = 9.8 m/s²
Therefore,
[tex]h = \frac{(75\ W)(7200\ s)}{(0.02\ kg)(9.8\ m/s^2)}[/tex]
h = 2755102 m = 2755.102 km
There are two beakers of water on the table. We can compare the average kinetic energy of the water molecules in the two beakers by measuring their
A temperatures.
B volumes.
C densities.
D masses.
Answer: masses
Explanation:
Trust me
An inductor of inductance 0.02H and capacitor of capatance 2uF are connected in series to an a.c. source of frequency 200 Hz- Calculate the Impedance in the circuit . TC
Explanation:
Given:
L = 0.02 H
C = [tex]2\:\mu \text{F}[/tex]
f = 200 Hz
The general form of the impedance Z is given by
[tex]Z = \sqrt{R^2 + (X_L - X_C)^2}[/tex]
Since this is a purely inductive/capacitive circuit, R = 0 so Z reduces to
[tex]Z = \sqrt{(X_L - X_C)^2} = \sqrt{\left(\omega L - \dfrac{1}{\omega C} \right)^2}[/tex]
[tex]\:\:\:\:\:\:\:= \sqrt{\left(2 \pi L - \dfrac{1}{2 \pi f C} \right)^2}[/tex]
[tex]\:\:\:\:\:\:\:= \sqrt{\left[2 \pi (200\:\text{Hz})(0.02\:\text{H}) - \dfrac{1}{2 \pi (200\:\text{Hz})(2×10^{-6}\:\text{F})} \right]^2}[/tex]
[tex]\:\:\:\:\:\:\:= \sqrt{(25.13\:\text{ohms} - 397.89\:\text{ohms})^2}[/tex]
[tex]\:\:\:\:\:\:\:=372.66\:\text{ohms}[/tex]
George Frederick Charles Searle
Answer:
George Frederick Charles Searle FRS was a British physicist and teacher. He also raced competitively as a cyclist while at the University of Cambridge. WikipediaExplanation:
GIVE BRAINLISTIn a television set the power needed to operate the picture tube comes from the secondary of a transformer. The primary of the transformer is connected to a 120-V receptacle on a wall. The picture tube of the television set uses 76 W, and there is 5.5 mA of current in the secondary coil of the transformer to which the tube is connected. Find the turns ratio Ns/Np of the transformer.
Ns/Np = ______.
Answer:
c) N_s / N_p = 115.15
Explanation:
Let's look for the voltage in the secondary, they do not indicate the power dissipated
P = V_s i
V_s = P / i
V_s = 76 / 5.5 10⁻³
V_s = 13.818 10³ V
the relationship between the primary and secondary of a transformer is
[tex]\frac{V_p}{N_p} = \frac{V_s}{N_s}[/tex]
[tex]\frac{N_s}{N_p} = \frac{V_s}{V_p}[/tex]
Ns / Np = 13,818 10³ /120
N_s / N_p = 115.15
A wheel has a diameter of 10m and weight 360N what minimum horizontal force is necessary to pull the wheel over a brick 0.1m when a force is applied at the wheel
A person with a near point of 85 cm, but excellent distant vision, normally wears corrective glasses. But he loses them while traveling. Fortunately, he has his old pair as a spare.
(a) If the lenses of the old pair have a power of +2.25 diopters, what is his near point (measured from his eye) when he is wearing the old glasses if they rest 2.0 cm in front of his eye?
(b) What would his near point be if his old glasses were contact lenses instead?
Answer:
a) p = 95.66 cm, b) p = 93.13 cm
Explanation:
For this problem we use the constructor equation
[tex]\frac{1}{f} = \frac{1}{p} + \frac{1}{q}[/tex]
where f is the focal length, p and q are the distances to the object and the image, respectively
the power of the lens is
P = 1 / f
f = 1 / P
f = 1 / 2.25
f = 0.4444 m
the distance to the object is
[tex]\frac{1}{p} = \frac{1}{f} -\frac{1}{q}[/tex]
the distance to the image is
q = 85 -2
q = 83 cm
we must have all the magnitudes in the same units
f = 0.4444 m = 44.44 cm
we calculate
[tex]\frac{1}{p} = \frac{1}{44.44} - \frac{1}{83}[/tex]
1 / p = 0.010454
p = 95.66 cm
b) if they were contact lenses
q = 85 cm
[tex]\frac{1}{p} = \frac{1}{44.44} - \frac{1}{85}[/tex]
1 / p = 0.107375
p = 93.13 cm
Question 3 of 10
Which statement describes the law of conservation of energy?
A. Air resistance has no effect on the energy of a system.
B. Energy cannot be created or destroyed.
C. The total energy in a system can only increase.
D. Energy cannot change forms.
هما
SUBMIT
Answer:
B . energy cannot be created or destroyed
recognizing forms of energy
Answer:
hi the question isn't obvious and need a photo I guess
