Suppose, we have a parallel plate capacitor and we know the following about it: Area of each plate = $0.0012m^2$ Distance between the two plates = $0.002m$ Charge on each plate after fully charging the capacitor = $2\times10^{-6}C$ Potential difference between the plates after fully charging the capacitor = $4\times 10^{-3}V$ My solution: We know that the electric field intensity at a point between two equally and oppositely charged plates is $\LARGE\frac{\sigma}{\epsilon_0}$. So, for the above case, $$\large E = \frac{\sigma}{\epsilon_0}$$ $$\large\implies E = \frac{\frac{2\times10^{-6}}{0.0012}}{8.85\times10^{-12}}{NC^{-1}}$$ $$\large\implies E =188323917.1NC^{-1}$$ My book's solution: $$E = \frac{V}{d}$$ $$\implies E=\frac{4\times 10^{-3}V}{0.002m}NC^{-1}$$ $$\implies E = 2NC^{-1}$$ If the books solution is correct, could you please explain why my answer is wrong and the book's is correct? Thanks in advance!

Answer:

In a tuning fork, two basic qualities of sound are considered, they are

1) The pitch of the waveform: This pitch depends on the frequency of the wave generated by hitting the tuning fork.

2) The loudness of the waveform: This loudness depends on the intensity of the wave generated by hitting the tuning fork.

Hitting the tuning fork harder will make it vibrate faster, increasing the number of vibrations per second. The number of vibration per second is proportional to the frequency, so hitting the tuning fork harder increase the frequency. From the explanation on the frequency above, we can say that by increasing the frequency the pitch of the tuning fork also increases.

Also, hitting the tuning fork harder also increases the intensity of the wave generated, since the fork now vibrates faster. This increases the loudness of the tuning fork.

Answer:

The force of the radiation on the surface is 3.33 x 10⁻¹⁰ N

Explanation:

Given;

intensity of light, I = 1kw/m² = 1000 W/m²

area of the surface, A = 1 cm² = 1 x 10⁻⁴ m²

Since the light is completely absorbed, the force of the radiation is given by;

F = P/c

where;

c is the speed of light = 3 x 10⁸ m/s

But P = IA

F = IA /c

F = (1000 X 1 X 10⁻⁴) / 3 x 10⁸

F = 3.33 x 10⁻¹⁰ N

Therefore, the force of the radiation on the surface is 3.33 x 10⁻¹⁰ N

The force of radiation will be "3.33 × 10⁻¹⁰ N"

According to the question,

Intensity of force, I = 1 kW/m² or,

                               = 1000 W/m²

Area of surface, A = 1 cm² or,

                              = 1 × 10⁻⁴ m²  

Speed of light, c = 3 × 10³ m/s

As we know the relation,

→ F = [tex]\frac{P}{c}[/tex]

or,

  P = IA

or,

  F = [tex]\frac{IA}{c}[/tex]

By substituting the values, we get

     = [tex]\frac{1000\times 1\times 10^{-4}}{3\times 10^3}[/tex]

     = 3.33 × 10⁻¹⁰ N

Thus the response above is correct.

Find out more information about intensity here:

https://brainly.com/question/1444040

Answer:

It does not violate the first law because the total energy taken is what is used 100J = 25J + 75J

But violates 2nd lawbecause the engine has a higher energy after doing work than the initial for e.g A cold object in contact with a hot one never gets colder, transferring heat to the hot object and making it hotter confirming the second law

Answer:

The spring constant should be:

[tex]k= 98\, \frac{N}{m}[/tex]

Explanation:

Use Hooke's law for this problem, knowing that the magnitude of the force (F) on the spring equals the stretching it experiences [tex]\Delta x[/tex] times the spring constant "k":

[tex]F=k\,\Delta x[/tex]

in our case, since the mass hanging is given in kg, we need to multiply it by "g" to get the force exerted:

Then if we add to the spring in its relaxed state, a mass of 0.10 kg, and we want for that a displacement of 1 cm (0.01 m), then the value of the spring constant should be:

[tex]k=\frac{F}{\Delta x} \\k=\frac{9.8\,(0.1)}{0.01} \, \frac{N}{m} \\k= 98\, \frac{N}{m}[/tex]

Answer:

5.2791264*10¹³

Explanation:

Convert the 9 years to seconds and then multiple it by 186000

The star is 4.62 x 10¹⁶ miles away from Earth.

The speed of light is 186,000 miles per second. It takes light from a particular star approximately 9 years to reach Earth. There are 365 days in 1 year, so it takes 9 x 365 = 3285 days for light from the star to reach Earth.

The distance between the star and Earth is 3285 x 186,000 = 608,810,000 miles. In scientific notation, this is 4.62 x 10¹⁶ miles.

Here is the calculation:

distance = speed * time

distance = 186,000 miles/second * 3285 days * 24 hours/day * 60 minutes/hour * 60 seconds/minute

distance = 608,810,000 miles

distance = 4.62 x 10¹⁶ miles

To know more about the Light, here

https://brainly.com/question/20296439

#SPJ2

Answer:

A) 0.0267 T

B) 0.0263 T

Explanation:

Given that

The number of turns, N = 400

Radius of the wire, r = 6 cm = 0.06 m

Current in the wire, I = 0.25 A

Relative permeability, K(m) = 80

See the attached picture for the calculation

The sign that represents a convex mirror is +f (option C). Details about convex mirror can be found below.

A convex mirror is that which is curved or bowed outward like the outside of a bowl or sphere or circle.

The focal length is the distance at which a lens or mirror is in focus. The focal length (f) is usually positive (+) for a convex mirror.

Therefore, the sign that represents a convex mirror is +f.

Learn more about convex mirror at: https://brainly.com/question/3627454

#SPJ1

Answer:

6 rad/s²

Explanation:

Sum the torques about the hinge.

∑τ = Iα

mg(L/2) = mL²/3 α

g/2 = L/3 α

α = 3g/(2L)

α = 3 (10 m/s²) / (2 × 2.50 m)

α = 6 rad/s²

Answer:

 P = 2923.89 W  

Explanation:

Power is

     P = F v

for which we must calculate the force, let's use Newton's second law, let's set a coordinate system with a flat parallel axis and the other axis (y) perpendicular to the plane

X Axis  

         F - Wₓ = 0

         F = Wₓ

Y Axis

         N -  [tex]W_{y}[/tex] = 0

let's use trigonometry for the components of the weight

         sin 6 = Wₓ / W

         cos 6 = W_{y} / W

         Wₓ = W sin 6

         W_{y} = W cos 6

          F = mg cos 6

          F = 75 9.8 cos 6

          F = 730.97 N

let's calculate the power

        P = F v

        P = 730.97 4.0

        P = 2923.89 W

Answer:

v = - 14.08 m / s

Explanation:

The definition of center of mass is

        [tex]x_{cm}[/tex] = 1 /M  ∑sun [tex]x_{i} m_{i}[/tex]

where M is the total mass of the system and [tex]x_{i}[/tex] and [tex]m_{i}[/tex] are the position and mass of each component.

The velocity of the center of mass can be found by deriving this expression with respect to time

         [tex]v_{cm}[/tex] = 1 / M ∑ m_{i} [tex]v_{i}[/tex] vi

let's find the total mass

          M = m₁ + m₂ + m₃ + m₄

          M = 1.45 + 2.81 +3.89 + 5.03

          m = 13.18 kg

let us substitute in the velocity of the center of mass [tex]v_{cm}[/tex] = 0

          0 = 13.18 (m₁ v₁ + m₂ v₂ + m₃v₃ + m₄v₄)

          v₄ = - (m₁ v₁ + m₂ v₂ + m₃v₃) / m₄

let's substitute the given values

v₄ = -[1.45 (6.09 +0.299 t) +2.81 (7.83 + 0.357t) +3.89 (8.09 + 0.405 t)] / 5.03

They ask us for the calculations for a time t = 2.83 s

          v₄ = - [8.8305 + 1.227 + 22.00 + 2.839 + 31.47 +4.4585] / 5.03

          v = - 14.08 m / s

The velocity of the particle 4 at time, t = 2.83 s, is -14.1 m/s.

The given parameters;

[tex]m_1 = 1.45 \ kg, \ \ v_1(t) = (6.09 \ m/s) + (0.299 \ m/s^2)\times t\\\\m_2 = 2.81 \ kg, \ \ v_2(t) = (7.83 \ m/s) + (0.357 \ m/s^2)\times t \\\\m_3 = 3.89 \ kg, \ \ v_3(t) = (8.09 \ m/s) + (0.405 \ m/s^2)\times t\\\\m_4 = 5.03 \ kg[/tex]

The velocity of the center mass of the particles is calculated as;

[tex]M_{cm}V_{cm} = m_1v_1 + m_2 v_2 + m_3v_3 + m_4v_4\\\\V_{cm} = \frac{m_1v_1 + m_2 v_2 + m_3v_3 + m_4v_4}{M_{cm}} \\\\0 = \frac{m_1v_1 + m_2 v_2 + m_3v_3 + m_4v_4}{M_{cm}}\\\\m_1v_1 + m_2 v_2 + m_3v_3 + m_4v_4 = 0\\\\m_4v_4 = -(m_1v_1 + m_2 v_2 + m_3v_3)\\\\v_4 = \frac{-(m_1v_1 + m_2 v_2 + m_3v_3)}{m_4}[/tex]

The velocity of particle 1 at time, t = 2.83 s;

[tex]v_1 = 6.09 \ + \ 0.299\times 2.83\\\\v_1 = 6.94 \ m/s[/tex]

The velocity of particle 2 at time, t = 2.83 s;

[tex]v_2 = 7.83\ + \ 0.357\times 2.83\\\\v_2 = 8.84 \ m/s[/tex]

The velocity of particle 3 at time, t = 2.83 s;

[tex]v_3 = 8.09\ + \ 0.405 \times 2.83\\\\v_3 = 9.24 \ m/s[/tex]

The velocity of the particle 4 at time, t = 2.83 s;

[tex]v_4 = \frac{-(m_1v_1 + m_2v_2 + m_3v_3)}{m_4} \\\\v_4 = \frac{-(1.45\times 6.94\ + \ 2.81\times 8.84\ + \ 3.89 \times 9.24)}{5.03} \\\\v_4 = -14 .1 \ m/s[/tex]

Thus, the velocity of the particle 4 at time, t = 2.83 s, is -14.1 m/s.

Learn more here:https://brainly.com/question/22698801

Answer:

The acceleration in the block is 2.1 m/s²

Explanation:

Given that,

Mass = 50 kg

Angle = 54°

Force = 40 N

Coefficient of friction = 0.33

We need to calculate the acceleration in the block

Using balance equation

[tex]F_{net}=F_{f}-F\cos\theta[/tex]

[tex]ma=\mu mg\sin\theta-F\cos\theta[/tex]

[tex]a=\dfrac{\mu mg\sin\theta-F\cos\theta}{m}[/tex]

Put the value into the formula

[tex]a=\dfrac{0.33\times50\times9.8\sin54-40\cos54}{50}[/tex]

[tex]a=2.1\ m/s^2[/tex]

Hence, The acceleration in the block is 2.1 m/s²

Answer:

HELLO your question has some missing parts below are the missing parts

note: The specific heat ratio and gas constant for air are given as k=1.4 and R=0.287 kJ/kg-K respectively.

--Given Values--

Inlet Temperature: T1 (K) = 325

Inlet pressure: P1 (kPa) = 560

Inlet Velocity: V1 (m/s) = 97

Throat Area: A (cm^2) = 5.3

Pressure upstream of (before) shock: Px (kPa) = 207.2

Mach number at exit: M = 0.1

Answer: A)  match number at inlet  = 0.2683

              B)  stagnation temperature at inlet =  329.68 k

              C)  stagnation pressure = 588.73 kPa

              D) ) Throat temperature = 274.73 k

Explanation:

Determining states at several locations in the system

A) match number at inlet

= V1 / C1 = 97/ 261.427 = 0.2683

C1 = sound velocity at inlet = [tex]\sqrt{K*R*T}[/tex] = [tex]\sqrt{1.4 *0.287*10^3}[/tex]  = 361.427 m/s

v1 = inlet velocity = 97

B) stagnation temperature at inlet

     = T1 + [tex]\frac{V1 ^2}{2Cp}[/tex]  = 325 + [tex]\frac{97^2}{2 * 1.005*10^{-3} }[/tex]

stagnation temperature = 329.68 k

C) stagnation pressure

= [tex]p1 ( 1 + 0.2Ma^2 )^{3.5}[/tex]

Ma = match number at inlet = 0.2683

p1 = inlet pressure = 560

hence stagnation pressure = 588.73 kPa

D) Throat temperature

= [tex]\frac{Th}{T} = \frac{2}{k+1}[/tex]

Th = throat temperature

T = stagnation temp at inlet = 329.68 k

k = 1.4

make Th subject of the relation

Th = 329.68 * (2 / 2.4 ) = 274.73 k

Answer:

b. The current in the loop always flows in a counterclockwise direction.

Explanation:

When a magnet falls through a loop of wire, it induces an induced current on the loop of wire. This induced current is due to the motion of the magnet through the loop, which cause a change in the flux linkage of the magnet. According to Lenz law, the induced current acts in such a way as to repel the force or action that produces it. For this magnet, the only opposition possible is to stop its fall by inducing a like pole on the wire loop to repel its motion down. An induced current that flows counterclockwise in the wire loop has a polarity that is equivalent to a north pole on a magnet, and this will try to repel the motion of the magnet through the coil. Also, when the magnet goes pass the wire loop, this induced north pole will try to attract the south end of the magnet, all in a bid to stop its motion downwards.

The current in the loop always flows in a counterclockwise direction. Hence, option (b) is correct.

The given problem is based on the concept and fundamentals of magnetic bars. When a magnet falls through a loop of wire, it induces an induced current on the loop of wire. There is some magnitude of current induced in the wire.

Thus, we can say that the current in the loop always flows in a counterclockwise direction. Hence, option (b) is correct.

Learn more about the magnetic field here:

https://brainly.com/question/14848188

Explanation:

Mary had 21 plants when she went on vacation.

When she got back, she only had 14 left alive.

We need to find the percent decrease in the number of plants.

Decrease in plants = 21 - 14 = 7

Percent decrease is given by :

[tex]\%=\dfrac{7}{21}\times 100\\\\\%=33.33\%[/tex]

So, there is 33% pf decrease in the number of plants.

Answer:

a) 5.5×10^17 Hz

b) visible light

Explanation:

Since the wavelength of the electromagnetic radiation must be about the size of the about itself, this implies that;

λ= 5.5 × 10^-10 m

Since;

c= λ f and c= 3×10^8 ms-1

f= c/λ

f= 3×10^8/5.5 × 10^-10

f= 5.5×10^17 Hz

The electromagnetic wave is visible light

Answer

The capacitor should be connected in parallel as parallel connection gives the arithmetic sum of capacitance which will give a corresponding sum of energy while capacitors in series gives the sum of the reciprocal if the individual capacitance

Answer:

Option 2 (observing, measuring, testing, and explaining their ideas) is the correct choice.

Explanation:

The other three choices have no relation to a particular task. So the option given here is just the right one.

Answer:

no, the truck is not overloaded

Explanation:

The computation is shown below;

Let us assume the mass of the loan in the second truck be M

So, the equation is as follows

{(Mass + M) × second truck × 1000 ÷ 3,600} = {(Mass + M + mass + first truck) × Pair moves away  × 1,000 ÷ 3,600}

{(5500 + M) × 64 × 1,000 ÷ 3,600 = {(5,500 + M + 5,500 + 3,900) × 44 × 1,000 ÷ 3,600}

(5500 + M) × 64 = (14,900 + M) × 44

352,000 + 64 M = 655,600 + 44 M

After solving this

M = 15,180 kg

Therefore the second truck is not overloaded

Answer:

77.96dB

Explanation:

Recall that decibels are a unit of measuring intensity of sound, and depend on the logarithm of the intensity

the intensity, measured in decibels is given by:

I(db)=10log(I/I0)

I is the intensity in MKS units; I0 is the threshold intensity for human hearing (10^-12 W/m^2)

Thus, if the two sounds together have a dB of 81, we know:

81=10log(I/I0)

using the data above, we can find the intensity of the two sounds to be

0.000125 W/m^2

therefore, one firecracker has an intensity half of that, or 0.0000625W/m^2

now use this value to find the dB of one firecracker:

I(dB0=10log(0.0000625/10^-12)=77.96dB

Answer:

The difference in angle of refraction between the red and blue light is 0.2°

Explanation:

Here is the complete question

Sunlight strikes a piece of crown glass at an angle of incidence of 37.4°. Calculate the difference in the angle of refraction between a red (660 nm) and a blue (470 nm) ray within the glass. The index of refraction is n=1.520 for red and n=1.531 for blue light.

Solution

From Snell's law refractive index n = sini/sinr where i = angle of incidence and r = angle of refraction.

Now for the red light n₁ = 1.520, i = 37.4° and r₁ = angle of refraction of red light

So, n₁ = sini/sinr₁

n₁sinr₁ = sini

sinr₁ = sini/n₁

r₁ = sin⁻¹(sini/n₁) = sin⁻¹(sin37.4°/1.52) = sin⁻¹(0.6074/1.52) = sin⁻¹(0.3996) = 23.55°

Now for the blue light n₂ = 1.531, i = 37.4° and r₂ = angle of refraction of blue light

So, n₂ = sini/sinr₂

n₂sinr₂ = sini

sinr₂ = sini/n₂

r₂ = sin⁻¹(sini/n₂) = sin⁻¹(sin37.4°/1.531) = sin⁻¹(0.6074/1.531) = sin⁻¹(0.3967) = 23.37°

So the difference in angle of refraction between the red and blue light is r₁ - r₂ = 23.55° - 23.37° = 0.18° ≅ 0.2°

Answer:

Explanation:

dipole moment = qs = q x s

= charge x charge separation

charge = q

separation between charge = s

half separation l = s / 2

dipole has two charges + q and - q separated by distance s .

Potential at distance x along x axis due to + q

[tex]v_1=\frac{1}{4\pi \epsilon } \times\frac{q}{x-l}[/tex]

Potential at distance x along x axis due to - q

[tex]v_2=\frac{1}{4\pi \epsilon } \times\frac{-q}{x+l}[/tex]

Total potential

v = v₁ + v₂

[tex]v=\frac{1}{4\pi \epsilon } \times( \frac{q}{x-l}-\frac{q}{x+l})[/tex]

[tex]v=\frac{1}{4\pi \epsilon } \times\frac{2ql}{x^2-l^2}[/tex]

[tex]v=\frac{1}{4\pi \epsilon } \times\frac{qs}{x^2-(\frac{s}{2}) ^2}[/tex]

Potential at distance y along y axis due to + q

[tex]v_1=\frac{1}{4\pi \epsilon } \times\frac{qs}{(y^2+\frac{s^2}{4})^\frac{1}{2} }[/tex]

Potential at distance y along y axis due to - q

[tex]v_1=\frac{1}{4\pi \epsilon } \times\frac{-qs}{(y^2+\frac{s^2}{4})^\frac{1}{2} }[/tex]

Total potential

v = v₁ + v₂

[tex]v= 0[/tex]

Answer:

the large amplitude wave keeps moving to the right

the small amplitude wave continues to move to the left.

When checking the answers, the correct ones are 1, 2

Explanation:

The waves fulfill the principle of superposition, which states that the value of the function at a point is the algebraic sum of the waves at a given instant.

The two waves in this exercise travel in the opposite direction, so when they are close, the resulting wave is the sum of the two waves, having a complicated shape. But when the waves follow their movement, they give in the same way as the initial a,

the large amplitude wave keeps moving to the right

the small amplitude wave continues to move to the left.

When checking the answers, the correct ones are 1, 2

Answer:

B.

Explanation:

The water collects in the ocean; it is then evaporated by the sun. After evaporation the water turns into water vapor, it then condenses to form clouds.

The ocean water prior to the part of the water cycle should be option B.

The ocean water should be collected back in the ocean prior to the part of the water cycle.

Because this should be done when it is evaporated by the sun.  When the evaporation is done so the water should be transformed into water vapor.

Find out more information about the  Water here:brainly.com/question/4381433?referrer=searchResults

Answer:

As in explanation.

Explanation:

A) Centre of Curvature: This is defined as the point in the center of the sphere from which the mirror was sliced. It is represented by the letter "C"

B) Vertex: It is defined as the point on the mirror's surface where the principal axis meets the mirror. It is represented by the letter A.

C) Focal Point: This is defined as the Midway point between the vertex and the center of curvature. It is represented by the letter "F"

D) Radius of Curvature: This is defined as the distance from the vertex to the center of curvature. It is represented by the letter "R"

E) Focal Length: This is defined as the distance from the mirror to the focal point. It's represented by the letter "f"

Answer:

3.5 m/s

Explanation:

There are 3 forces on the cyclist:

Weight force mg pulling down,

Normal force N pushing up,

and friction force Nμ pushing left.

Sum of forces in the y direction:

∑F = ma

N − mg = 0

N = mg

∑F = ma

-Nμ = ma

-mgμ = ma

a = -gμ

a = -(10 m/s²)(0.60)

a = -6 m/s²

Velocity reached at end of 11 m:

v² = v₀² + 2aΔx

v² = (12 m/s)² + 2 (-6 m/s²) (11 m)

v = √12 m/s

v ≈ 3.5 m/s

Answer:

The same amount of current flows through the battery and light bulb

Explanation:

Because for a single loop, the current is the same at every point in the loop. Thus, the amount of current that flows through the lightbulb is the same as the amount that flows through the battery

Answer:

The same amount of current flows through the battery and light bulb

Explanation:

Answer;

a 2.00-kg body will vibrate at 0.707Hz

Answer:-7.9

Explanation:

Answer:   2

Explanation:

1/2=1/1 +1/x

x=-2

magnification= 2/1

magnification=2

Answer:

-transform plate boundary

- false