Answer:
the person's heart rate
Two resistors with resistance values of 4.5 Ω and 2.3 Ω are connected in series or parallel
across a 30 V potential difference to a light bulb.
a. Calculate the current delivered through the light bulb in the two cases.
b. Draw the circuit connection that will achieve the brightest light bulb.
Explanation:
Given that,
Two resistors 4.5 Ω and 2.3 Ω .
Potential difference = 30 V
When they are in series, the current through each resistor remains the same. First find the equivalent resistance.
R' = 4.5 + 2.3
= 6.8 Ω
Current,
[tex]I=\dfrac{V}{R'}\\\\I=\dfrac{30}{6.8}\\\\=4.41\ A[/tex]
So, the current through both lightbulb is the same i.e. 4.41 A.
When they are in parallel, the current divides.
Current flowing in 4.5 resistor,
[tex]I_1=\dfrac{V}{R_1}\\\\=\dfrac{30}{4.5}\\\\I_1=6.7\ A[/tex]
Current flowing in 2.3 ohm resistor,
[tex]I_2=\dfrac{V}{R_2}\\\\=\dfrac{30}{2.3}\\\\I_2=13.04[/tex]
In parallel combination, are brighter than bulbs in series.
A certain heating element is made out of Nichrome wire and used with the standard voltage source of V=120 V. Immediately after the voltage is turned on, the current running through the element is measured at I1=1.28 A and its temperature at T1=25°C. As the heating element warms up and reaches its steady-state (operating) temperature, the current becomes I2=1.229 A.
Required:
Find this steady-state temperature T2.
Answer:
T₁ = 232.5 ºC
Explanation:
For this exercise let's start by finding the value of the resistance for the two currents, using Ohm's law
V = i R
R = V / i
i₀ = 1.28 A
R₀ = 120 / 1.28
R₀ = 93.75 ohm
i₁ = 1.229 A
R₁ = 120 / 1.229
R₁ = 97.64 or
Resistance in a metal is linear with temperature
ΔR = α R₀ ΔT
where the coefficient of thermal expansion for Nichrome is α=0.0002 C⁻¹
ΔT = [tex]\frac{\Delta R}{\alpha R_o}[/tex]
ΔT = [tex]\frac{97.64 \ -93.75}{ 0.00020 \ 93.75}[/tex]
ΔT = 2,075 10² C
ΔT = T₁-T₀ = 2,075 10²
T₁ = T₀ + 207.5
T₁ = 25+ 207.5
T₁ = 232.5 ºC
A 70-turn coil has a diameter of 11 cm. Find the magnitude of the emf induced in the coil (in V) if it is placed in a spatially uniform magnetic field of magnitude 0.70 T so that the face of the coil makes the following angles with the magnetic field, and the magnetic field is reduced to zero uniformly in 0.2 s.
This question is incomplete, the complete question is;
A 70-turn coil has a diameter of 11 cm. Find the magnitude of the emf induced in the coil (in V) if it is placed in a spatially uniform magnetic field of magnitude 0.70 T so that the face of the coil makes the following angles with the magnetic field, and the magnetic field is reduced to zero uniformly in 0.2 s. a) θ = 30° V b) θ = 60° V c) θ = 90° V
Answer:
the magnitude of the emf induced in the coil are;
a)- For θ = 30°, e = 1.16 V
b)- For θ = 60°, e = 2.01 V
c)- For θ = 90°, e = 2.33 V
Explanation:
Given the data in the question;
number of turns N = 70
Diameter of coil D = 11 cm
Radius r = D/2 = 11/2 = 5.5 cm = 0.055 m
magnitude of magnetic ΔB = 0.7T
Δt = 0.2 seconds
Now,
a)
For θ = 30°,
Angle of with area of vector θ' = 90° - 30° = 60°
so
emf e = N( Δ∅ / Δt ) = N( ΔBAcosθ / Δt )
hence
e = NAcosθ'(ΔB / Δt )
where A is area ( πr² )
so we substitute
e = 70 × πr² × cos(60°) × ( 0.7 / 0.2 )
e = 70 × π(0.055)² × cos(60°) × ( 0.7 / 0.2 )
e = 1.16 V
b)
For θ = 60°,
Angle of with area of vector θ' = 90° - 60° = 30°
so
e = NAcosθ'(ΔB / Δt )
we substitute
e = 70 × πr² × cos(30°) × ( 0.7 / 0.2 )
e = 70 × π(0.055)² × cos(30°) × ( 0.7 / 0.2 )
e = 2.01 V
c)
For θ = 90°,
Angle of with area of vector θ' = 90° - 90° = 0°
so
e = NAcosθ'(ΔB / Δt )
we substitute
e = 70 × πr² × cos(0°) × ( 0.7 / 0.2 )
e = 70 × π(0.055)² × cos(30°) × ( 0.7 / 0.2 )
e = 2.33 V
Therefore, the magnitude of the emf induced in the coil are;
a)- For θ = 30°, e = 1.16 V
b)- For θ = 60°, e = 2.01 V
c)- For θ = 90°, e = 2.33 V
A tall cylinder contains 25 cm of water. Oil is carefully poured into the cylinder, where it floats on top of the water, until the total liquid depth is 40 cm. What is the gauge pressure at the bottom of the cylinder
Answer: [tex]377.3\ kPa[/tex]
Explanation:
Given
Water column height [tex]h=25\ cm[/tex]
After oil is poured, the total height becomes [tex]h'=40\ cm[/tex]
Pressure at the bottom will be the sum due to the water and oil column
Suppose the density of the oil is [tex]\rho=900\ kg/m^3[/tex]
Pressure at the bottom
[tex]\Rightarrow P=10^3\times g\times 25+900\times g\times 15\\\Rightarrow P=100g[250+135]\\\Rightarrow P=3773\times 100\ Pa\\\Rightarrow P=377.3\ kPa[/tex]
A 900 kg car travelling at 12 m/s due east collides with a 600 kg car travelling at 24 m/s due north. As a result of the collision, the two cars lock together and move in what final direction?
45.0° N of E
53.1° N of E
63.3° N of E
69.5° N of E
Calculate force of each car:
P1 = 900 kg x 12m/s = 10,800
P2= 600 x 24 = 14,400
Degree of travel = arctan(14,300/10800)
Degree of travel = 53.1 N of E
A uniform magnetic field is directed at an angle of 30o with the plane of a circular coil of radius 4cm and 1000 turns. The magnetic field changes at a rate of 5 T per second. Calculate the following:
a. Area vector
b. Induced emf
Answer:
(a) The area vector is 0.00503 m² at 30⁰ from the magnetic field
(b) The induced emf is 12.58 V
Explanation:
Given;
angle between the magnetic field and the plane of the circular coil, = 30⁰
number of turns of the coil, N = 1000
radius of the coil, r = 4 cm = 0.04 m
change in the magnetic field with time, dB/dt = 5 T/s
(a) The area vector is calculated as;
A = πr²
A = π x (0.04)²
A = 0.00503 m²
The area vector is 0.00503 m² at 30⁰ from the magnetic field.
(b) The induced emf is calculated as;
[tex]emf = N\frac{\Delta \phi}{\Delta t} \\\\where;\\\\\phi = BAcos \theta\\\\emf = N\times \frac{dB}{dt} \times Acos (\theta)\\\\where;\\\\\theta \ is \ the \ angle \ between \ a \ perpendicular \ vector \ to \ the \ area\\ and\ the \ magnetic\ field\\\\\theta = 90 - 30 = 60^0\\\\emf = N\times \frac{dB}{dt} \times Acos (\theta)\\\\emf = (1000) \times (5 )\times (0.00503) \times cos (60)\\\\emf = 12.58 \ V[/tex]
omparing Technological Design and Scientific Investigation
Explain how the stages of technological design are similar to the process of scientific investigation. Use specific stages from each process to support your answer
Answer:
杰恩斯克克斯克奇沃伊斯克克斯克什德布德克什恩克恩德恩克恩茨克杰兹姆克斯恩斯姆斯姆德恩德姆德武伊乔奥斯克斯杰德布德赫德夫赫富伊什杰吉迪赫德赫夫赫德
Answer:
Scientists learn more about the natural world through investigation by identifying a problem, researching related information, designing and conducting an investigation, analyzing the results, evaluating the conclusion, and communicating the findings. Engineers follow similar steps when creating new products or solutions through technological design. The four stages of technological design include identifying a need, designing and implementing a solution, and evaluating the solution.
hi can anyone pls answer this question. i will mark brainliest
Answer:
a.work done by man A is zero
D is best option
Explanation:
D none of them because as we know that to do work some distance should be cover with some load as both picture they are covering some distance with carrying some load so A and B option are absolutely wrong and remaining C they are not doing same amount of work because distance cover by them and load carrying by them is different so how can work be same so D is best option none of A B C is correct answer
If four students separately measure the density of a rock, and they all have very low percent
differences between their measurements, what can you say for certain about the accuracy of their
results?
Answer:
Their measured results are closer to the exact or true value. Hence, their measured value is considered to be more accurate.
Explanation:
Considering the situation described above, the accuracy of a measured value depicts how closely a measured value is to the accurate value.
Hence, since the students' measured values have very low percent differences, it shows the similarity of computations or estimates to the actual values, which in turn offers a smaller measurement error.
Therefore, their measured results are closer to the exact or true value, which implies that their measured value is considered to be more accurate.
in an experiment the following readings were observed volume of alcohol flowing per minute equals to 10 raise to power - 5 cube volume density of alcohol is 800 kg per metre cube length of cube is 0.5 m radius of tube is 0.05 cm height of alcohol is 60 cm calculate the coefficient of viscosity of alcohol
Answer:
The viscosity is 1.30 x 10^-3 deca poise.
Explanation:
Volume per minute, V = 10^-5 m^3
Volume per second, V = 1.67 x 10^-7 m^3
density, d = 800 kg/m^3
radius, r = 0.05 cm
Length, L = 0.5 m
Height, h = 60 cm
Pressure, P = h d g = 0.6 x 800 x 9.8 = 4704 Pa
Use the formula of rate of flow
[tex]V = \frac{\pi p r^4}{8\eta L}\\\\1.67\times 10^{-7}\times8\times \eta\times 0.5 = 3.14\times 4707\times (0.05\times 10^{-2})^4\\\\\eta = 1.38\times 10^{-3} deca poise[/tex]
The average 8-18 year old spends how many hours per day average in front of a screen doing little physical activity
Nearly four hours every day, doing little to no physical activity.
A uniform circular disk has a radius of 34 cm and a mass of 350 g. Its center is at the origin. Then a circular hole of radius 6.8 cm is cut out of it. The center of the hole is a distance 10.2 cm from the center of the disk. Find the moment of inertia of the modified disk about the origin.
Answer:
u can ask it to the person who give ot to u i dont no
When a player's finger presses a guitar string down onto a fret, the length of the vibrating portion of the string is shortened, thereby increasing the string's fundamental frequency. The string's tension and mass per unit length remain unchanged.
If the unfingered length of the string is l=65cm, determine the positions x of the first six frets, if each fret raises the pitch of the fundamental by one musical note in comparison to the neighboring fret. On the equally tempered chromatic scale, the ratio of frequencies of neighboring notes is 21/12
x1=
x2=
x3=
x4=
x5=
x6=
Answer:
Explanation:
For frequencies n generated in a string , the expression is as follows
n = 1 /2L√ ( T/m )
n is fundamental frequency , T is tension in string , m is mass per unit length and L is length of string.
If T and m are constant , then
n x L = constant , hence n is inversely proportional to L or length of string.
Frequencies increase by 21/12 = 1.75 , length must decrease by 1 / 1.75 times
Initial length of string is 65 cm .
x1 = 65 x 1 / 1.75 = 37.14 cm
x2 = 37.14 x 1/ 1.75 = 21.22 cm
x3 = 21.22 x 1 / 1.75 = 12.12 cm
x4= 12.12 x 1 / 1.75 = 6.92 cm
x5 = 6.92 x 1 / 1.75 = 3.95 cm
x6 = 3.95 x 1 / 1.75 = 2.25 cm
a 2.00 kg object is moving east at 4.00 m/s when it collides with a 6 kg object that is initially at rest. after the collision the larger object moves east at 1 m/s. what is the final velocity of the smaller object after the collision
The final velocity of the smaller object is 1 m/s.
To calculate the final velocity of the smaller object, we use the formula below.
Formula:
mu+m'u' = mv+m'v'............. Equation 1Where:
m = mass of the bigger objectm' = mass of the smaller objectu = initial velocity of the bigger objectu' = initial velocity of the smaller objectv = final velocity of the bigger objectv' = final velocity of the smaller object.From the question,
m = 6 kgm' = 2 kgu = 0 m/s (at rest) u' = 4 m/sv = 1 m/sSubstitute these values into equation 1
6(0)+2(4) = 6(1)+2(v')8 = 6+2v'2v' = 8-62v' = 2v' = 1 m/sHence, The final velocity of the smaller object is 1 m/s.
Learn more about velocity here: https://brainly.com/question/25749514
A bullet is fired vertically upward a velocity of 80m/s to what height will the bullet rise above the point of projection
Answer:
The bullet will rise 320 meters above the point of projection.
Explanation:
Assuming that air friction is negligent we can use the kinematic equation:
[tex]v_{2} ^2=v_{1} ^2+2(-a)d\\0\frac{m^2}{s^2} =6400\frac{m^2}{s^2} +2(-10\frac{m}{s^2} )d\\-6400\frac{m^2}{s^2} =(-20\frac{m}{s^2}) d\\320m=d[/tex]
*acceleration is negative (-a) as it is acting in the opposite direction of the motion of the bullet.*
The bullet rises to a height of 3600 m if a bullet is fired upward with a velocity of 80 m/s.
Assume the air friction is negligible, the kinematic equation:
[tex]v_f^2 = v_i^2 +2(-a) d[/tex]
Where,
[tex]v_i^2[/tex] - iinitial velocity = 80 m/s
[tex]v_f^2[/tex]- final velocity = 0
[tex]d[/tex]- distance= ?
[tex]a[/tex]- gravitational acceleration = 9.8 m/s² = 10 m/s²
Put the values in the formula,
[tex]\begin {aligne} 0 = (80)^2 + 2 (10)^2 d\\\\d = \dfrac {6400}{ 200}\\\\d &= 3600 \rm \ m\end {aligne}\\[/tex]
Therefore, the bullet rises to a height of 3600 m if a bullet is fired upward with a velocity of 80 m/s.
To know more about kinematic equation:
https://brainly.com/question/5955789
Help please. I don’t understand
(D)
Explanation:
That's the statement of the Pythagorean theorem.
[tex]c^2=a^2+b^2 \Rightarrow c = \sqrt{a^2+b^2}[/tex]
What magnitude point charges creates a 10000 N/C electric field at a distance of 0.5 m?
a. 877.2 nC
b. 287.7 nC
c. 277.8 nC
d. 872.7 nC
Answer:
c. 277.8 nC
Explanation:
applying,
E = kq/r²............. Equation 1
Where E = electric field intensity, q = charge, r = distance, k = coulomb's constant.
make q the subject of the equation
q = Er²/k............... Equation 2
From the question,
Given: E = 10000 N/C, r = 0.5 m
Constant: k = 9×10⁹ Nm²/C²
Substitute these values into equation 2
q = (10000×0.5²)/(9×10⁹)
q = 277.8×10⁹
q = 277.8 nC
Hence the right option is c. 277.8 nC
Thermodynamic Processes: An ideal gas is compressed isothermally to one-third of its initial volume. The resulting pressure will be
Answer:
The resulting pressure is 3 times the initial pressure.
Explanation:
The equation of state for ideal gases is described below:
[tex]P\cdot V = n \cdot R_{u}\cdot T[/tex] (1)
Where:
[tex]P[/tex] - Pressure.
[tex]V[/tex] - Volume.
[tex]n[/tex] - Molar quantity, in moles.
[tex]R_{u}[/tex] - Ideal gas constant.
[tex]T[/tex] - Temperature.
Given that ideal gas is compressed isothermally, this is, temperature remains constant, pressure is increased and volume is decreased, then we can simplify (1) into the following relationship:
[tex]P_{1}\cdot V_{1} = P_{2}\cdot V_{2}[/tex] (2)
If we know that [tex]\frac{V_{2}}{V_{1}} = \frac{1}{3}[/tex], then the resulting pressure of the system is:
[tex]P_{2} = P_{1}\cdot \left(\frac{V_{1}}{V_{2}} \right)[/tex]
[tex]P_{2} = 3\cdot P_{1}[/tex]
The resulting pressure is 3 times the initial pressure.
State what is meant by a gravitational potential at point A is -1·70 × 109 J kg-1.
Answer:
The energy stored in a body due to either it's position or change in shape is called gravitational potential energy.
Some copper wire has a resistance of 200 ohms at 20 degrees C . A current is then passed through the same wire and the temperature rises to 90 degrees C. Determine the resistance of the wire at 90 degrees correct to the nearest ohm assuming the coefficient of resistance is 0.004/degree C at 0 degrees
Answer:
256 ohms
Explanation:
Applying,
R = R'[1+α(T-T')]............. Equation 1
Where R = Final resistance of the wire, R' = Initial resistance of the wire, T = Final temperature, T' = Initial temperature, α = Temperature coefficient of resistance
From the question,
Given: R' = 200 ohms, T = 90 degrees, T' = 20 degrees, α = 0.004/degree
Substitute these values into equation 1
R = 200[1+0.004(90-20)]
R = 200[1+0.28]
R = 200(1.28)
R = 256 ohms
The resistance of the wire at 90 °C correct to the nearest ohm assuming the coefficient of resistance is 0.004 °C¯¹ is 256 ohm
Data obtained from the question Original resistance (R₁) = 200 ohmOriginal temperature (T₁) = 20 °C Coefficient of resistivity (α) = 0.004 °C¯¹New temperature (T₂) = 90 °C New resistance (R₂) =? How to determine the new resistanceα = R₂ – R₁ / R₁(T₂ – T₁)
0.004 = R₂ – 200 / 200(90 – 20)
0.004 = R₂ – 200 / 200(70)
0.004 = R₂ – 200 / 14000
Cross multiply
R₂ – 200 = 0.004 × 14000
R₂ – 200 = 56
Collect like terms
R₂ = 56 + 200
R₂ = 256 ohm
Learn more about linear expansion:
https://brainly.com/question/23207743
How much work does a supermarket checkout attendant do on a can of soup he pushes 0.420 m horizontally with a force of 4.60 N? Express your answer in joules and kilocalories.
We know
[tex]\boxed{\sf Work\:Done=Force\times Displacement} [/tex]
[tex]\\ \rm\longmapsto Work\:done=0.420\times 4.60[/tex]
[tex]\\ \rm\longmapsto Work\:done=1.932J[/tex]
What is your angular position 75 seconds after the wheel starts turning, measured counterclockwise from the top? Express your answer as an angle between 0∘ and 360∘. Express your answer in degrees.
Complete Question
A Ferris wheel on a California pier is 27 m high and rotates once every 32 seconds in the counterclockwise direction. When the wheel starts turning, you are at the very top.
What is your angular position 75 seconds after the wheel starts turning, measured counterclockwise from the top? Express your answer as an angle between 0∘ and 360∘. Express your answer in degrees.
Answer:
[tex]\phi=123.75[/tex]
Explanation:
From the question we are told that:
Height [tex]h=27m[/tex]
Period [tex]T=32sec[/tex]
Time [tex]t=75sec[/tex]
Generally the equation for angular velocity is mathematically given by
[tex]\omega=\frac{2 \pi}{T}[/tex]
[tex]\omega=\frac{2 \pi}{32}[/tex]
[tex]\omega=0.196rad/s[/tex]
Therefore
[tex]\theta=\omega t[/tex]
[tex]\theta=0.196rad/s*75sec[/tex]
[tex]\theta=843.75 \textdegree[/tex]
Therefore
[tex]\phi=\theta-2(360)[/tex]
[tex]\phi=123.75[/tex]
what is the critical angle of light traveling from vegetable oil into water
56.1∘
Question: A glass is half-full of water, with a layer of vegetable oil (n = 1.47) floating on top. A ray of light traveling downward through the oil is incident on the water at an angle of 56.1∘ .
A glass is half-full of water, with a layer of vegetable oil (n ...https://study.com › academy › answer › a-glass-is-half-ful...
While standing at the edge of the roof of a building, a man throws a stone upward with an initial speed of 6.63 m/s. The stone subsequently falls to the ground, which is 14.5 m below the point where the stone leaves his hand.
At what speed does the stone impact the ground? Ignore air resistance and use =9.81 m/s2 for the acceleration due to gravity.
impact speed:
18.1151
m/s
How much time is the stone in the air?
elapsed time:
Answer:
Explanation:
You final velocity is correct but not to the correct number of significant digits. The actual answer should be 18.1 m/s. We will use that to find the total time the stone was in the air in the equation:
v = v₀ + at
18.1 = 6.63 + (-9.81)t and
11.5 = -9.81t so
t = 1.17 seconds.
We know this was how long the stone was in the air (as compared to the time that the stone took to reach its max height or some other height) because we used the velocity with which the stone hit the ground to find the total time the rock was in the air before it hit the ground going at that velocity.
* 1a Average speed
Carl Lewis runs the 100 m sprint in about 10 s.
His average speed in units of m/s would be:
of
Answer:
Explanation:
[tex] \implies v_{av} = \dfrac{total \: displacement}{total \: time} [/tex]
[tex] \implies v_{av} = \dfrac{100}{10} [/tex]
[tex]\implies v_{av} =10 \: {ms}^{ - 1} [/tex]
When the gun fires a projectile with a mass of 0.040 kg and a speed of 380 m/s, what is the recoil velocity of the shotgun and arm–shoulder combination?
Complete question:
The recoil of a shotgun can be significant. Suppose a 3.6-kg shotgun is held tightly by an arm and shoulder with a combined mass of 15.0 kg. When the gun fires a projectile with a mass of 0.040 kg and a speed of 380 m/s, what is the recoil velocity of the shotgun and arm–shoulder combination?
Answer:
The recoil velocity of the shotgun and arm–shoulder combination is 1.013 m/s
Explanation:
Given;
combined mass of the shotgun and arm–shoulder, m₁ = 15 kg
mass of the projectile, m₂ = 0.04 kg
speed of the projectile, u₂ = 380 m/s
let the recoil velocity of the shotgun and arm–shoulder combination = u₁
Apply the principle of conservation of linear momentum;
m₁u₁ + m₂u₂ = 0
m₁u₁ = - m₂u₂
[tex]u_1 = -\frac{m_2u_2}{m_1} \\\\u_1 = - \frac{0.04\times 380}{15} \\\\u_1 =-1.013 \ m/s\\\\u_1 = 1.013 \ m/s \ \ \ in \ opposite \ direction[/tex]
Therefore, the recoil velocity of the shotgun and arm–shoulder combination is 1.013 m/s
when we jump on a concrete surface,the feet get injured.Why
Answer:
Explanation:
Bhjb
Explanation:
its because a concrete surface is a hard surface which doesn't absorb the energy of gravitation when we fall down so we get hurt more badly..
hope this helps
In a race, Usain Bolt accelerates at
1.99 m/s2 for the first 60.0 m, then
decelerates at -0.266 m/s2 for the final
40.0 m. How much time did the race take?
(Unit = s)
Answer:
65.87 s
Explanation:
For the first time,
Applying
v² = u²+2as.............. Equation 1
Where v = final velocity, u = initial velocity, a = acceleration, s = distance
From the question,
Given: u = 0 m/s (from rest), a = 1.99 m/s², s = 60 m
Substitute these values into equation 1
v² = 0²+2(1.99)(60)
v² = 238.8
v = √238.8
v = 15.45 m/s
Therefore, time taken for the first 60 m is
t = (v-u)/a............ Equation 2
t = (15.45-0)/1.99
t = 7.77 s
For the final 40 meter,
t = (v-u)/a
Given: v = 0 m/s(decelerates), u = 15.45 m/s, a = -0.266 m/s²
Substitute into the equation above
t = (0-15.45)/-0.266
t = 58.1 seconds
Hence total time taken to cover the distance
T = 7.77+58.1
T = 65.87 s
A 215 N sign is supported by two ropes. One rope pulls up and to the right 1=29.5∘ above the horizontal with a tension 1 , and the other rope pulls up and to the left 2=44.5∘ above the horizontal with a tension 2 , as shown in the figure. Find the tensions 1 and 2 .
The sign is held in equilibrium. Using Newton's second law, we set up the equations of the net forces acting on the sign in the horizontal and vertical directions:
∑ F (horizontal) = T₁ cos(29.5°) - T₂ cos(44.5°) = 0
(right is positive, left is negative)
∑ F (vertical) = T₁ sin(29.5°) + T₂ sin(44.5°) - 215 N = 0
(up is positive, down is negative)
Solve the system of equations. I use elimination here:
• Multiply the first equation by sin(29.5°) and the second by cos(29.5°):
sin(29.5°) (T₁ cos(29.5°) - T₂ cos(44.5°)) = 0
cos(29.5°) (T₁ sin(29.5°) + T₂ sin(44.5°) - 215 N) = 0
T₁ cos(29.5°) sin(29.5°) - T₂ cos(44.5°) sin(29.5°) = 0
T₁ cos(29.5°) sin(29.5°) + T₂ cos(29.5°) sin(44.5°) = (215 N) cos(29.5°)
• Subtract the first equation from the second to eliminate T₁ :
T₂ cos(29.5°) sin(44.5°) - (- T₂ cos(44.5°) sin(29.5°)) = (215 N) cos(29.5°)
• Solve for T₂ :
T₂ (cos(29.5°) sin(44.5°) + cos(44.5°) sin(29.5°)) = (215 N) cos(29.5°)
T₂ sin(74.0°) = (215 N) cos(29.5°)
… … … (using the fact that sin(x + y) = sin(x) cos(y) + cos(y) sin(x))
T₂ = (215 N) cos(29.5°) / sin(74.0°)
T₂ ≈ 195 N
• Solve for T₁ :
T₁ cos(29.5°) - T₂ cos(44.5°) = 0
T₁ cos(29.5°) = T₂ cos(44.5°)
T₁ = T₂ cos(44.5°) / cos(29.5°)
T₁ ≈ 160. N
Estimate the average power of a water wave when it hits the chest of an adult standing in the water at the seashore. Assume that the amplitude of the wave is 0.56 m , the wavelength is 2.0 m , and the period is 3.4 s . Assume that the area of the chest is 0.14 m^2.
Answer:
[tex]P=45.2W[/tex]
Explanation:
From the question we are told that:
Amplitude [tex]A=0.56m[/tex]
Period [tex]T=3.4s[/tex]
Wavelength [tex]\lambda=2.0[/tex]
Area [tex]a=0.14m^2[/tex]
Generally the equation for Power is mathematically given by
[tex]Power = 2 \pi ^2 \rho a(\frac{\lambda}{T})(\frac{1}{T})*A[/tex]
[tex]P= 2 3.142^2 1025 0.14(\frac{2.0}{3.4})(\frac{1}{3.4})^2*0.56^2[/tex]
[tex]P=45.2W[/tex]
