The definition of the unit of current, the Ampere,is based on A. The force per unit length on a conductor in a uniform magnetic field B. The force per unit length on parallel current carrying conductors C. The charge per unit time delivered by a cell of e.m.f 1.0 V D. The charge passing a point per unit time in electrical current

Bending allowance is the amount by which the total run that conduit can cover is reduced because of the extra length required to bend around an obstacle.

When running conduit, bending is necessary to go around obstructions like structural members or corners. In order to avoid the use of too many fittings and to make installation faster and more efficient, it is best to avoid angles less than 30 degrees.
When measuring conduit length, it is important to include the bending allowance. The length of the conduit required can be calculated using the following formula:
Bending allowance = (Conduit diameter x bending angle) x 0.0175
Where,
Bending allowance is the additional length of the conduit needed to make the bend.
Conduit diameter is the diameter of the conduit being used.
Bending angle is the angle of the bend being made.
0.0175 is the constant factor used in this calculation.
For example, suppose we have to bend a 1.5-inch diameter conduit around a corner with a 45-degree angle. The bending allowance for this conduit would be:
Bending allowance = (1.5 x 45) x 0.0175
Bending allowance = 1.4 inches
So, when measuring the length of the conduit required for this bend, 1.4 inches should be added to the length of the conduit required to make up for the bending allowance.

The amount by which the total run that conduit can cover is reduced because of the extra length required to bend around an obstacle is called the bending allowance.

For similar question on Bending

https://brainly.com/question/16107975

#SPJ11

Question:-

___ is the amount by which the total run that conduit can cover is reduced because of the extra length required to bend around an obstacle.

a. The angular acceleration of the engine is -1320 rad/s².

b. The engine makes approximately 118.7 revolutions during the deceleration.

Given:

Initial angular velocity (ω1) = 4500 rpm

Final angular velocity (ω2) = 1200 rpm

Time is taken (t) = 2.5 s

a) The formula for angular acceleration is:

α = (ω2 - ω1) / t

Substituting the given values, we get:

α = (1200 rpm - 4500 rpm) / 2.5 s = -1320 rad/s² (negative sign indicates a deceleration)

Therefore, the angular acceleration of the engine is -1320 rad/s².

b) To find the total number of revolutions, we need to convert the initial and final angular velocities from rpm to rad/s:

ω1 = 4500 rpm × 2π/60 = 471 rad/s

ω2 = 1200 rpm × 2π/60 = 126 rad/s

The average angular velocity (ω_avg) during the deceleration is given by:

ω_avg = (ω1 + ω2) / 2 = (471 rad/s + 126 rad/s) / 2 = 298.5 rad/s

The total angular displacement (θ) of the engine during the deceleration is given by:

θ = ω_avg × t = 298.5 rad/s × 2.5 s = 746.25 rad

Finally, the total number of revolutions (N) made by the engine is:

N = θ / 2π = 746.25 rad / 2π rad/rev = 118.7 rev (approximately)

Therefore, the engine makes approximately 118.7 revolutions during the deceleration.

learn more about angular acceleration here

https://brainly.com/question/21278452

#SPJ1

When a ray of light hits a surface, the angles made by the reflection and refraction of the ray must all be measured from the normal, which is perpendicular to the surface at the point where the light ray hits it.

Reflection occurs when light rays hit a surface and bounce back whereas Refraction, occurs when light travels through a medium of a different density or refractive index.

The laws of reflection and refraction states that the angle of incidence is equal to the angle of reflection, and the ratio of the sine of the angle of incidence to the sine of the angle of refraction is constant. This ratio is known as the refractive index of the material from where the light is passing through.

To know more about reflection and refraction refer to:

brainly.com/question/16957723

#SPJ4

The charge that passes through the capacitor is 3.132 mC (milli Coulombs). Therefore, option B. 3.132 mCis the correct answer.

The circuit shown below is a simple circuit consisting of a battery, a capacitor, and a switch.

The capacitance of the capacitor is 27 µF, and it is initially uncharged. After switch S is closed, how much charge will pass through it?

Circuit diagram with a capacitor

The expression for the amount of charge (Q) that passes through the capacitor is

Q = CΔV,

where, C is the capacitance of the capacitor and

ΔV is the potential difference between the plates of the capacitor.

Q = CΔV = (27 × 10-6 F)(116 V)

Q = 3132 × 10-6 C

Q = 3.132 mC

The charge that passes through the capacitor is 3.132 mC (milli Coulombs).

for such more question on capacitor

https://brainly.com/question/21851402

#SPJ11

To determine the angle of the largest incline the truck can climb at a constant speed of 72 km/h, we need to use the formula for power, which is P = Fv, where P is the power, F is the force, and v is the velocity.

Since the velocity is constant, the force required to maintain this speed up an incline is equal to the force of gravity acting on the truck, which is given by Fg = mg, where m is the mass of the truck and g is the acceleration due to gravity.

Thus, we can write the equation for the maximum incline angle as:

sinθ = Fg/F

where θ is the angle of the incline. Substituting the given values, we get:

sinθ = (mg)/Pv

sinθ = (120000 kg)(9.81 m/s²)

sinθ =( 0.157)/(380000 W)(20 m/s)

θ = 9.04 degrees

Therefore, the angle of the largest incline the truck can climb at a constant speed of 72 km/h is approximately 9.04 degrees.

To know more about constant speed , visit :

https://brainly.com/question/24909693

#SPJ1

The maximum angle of incline the truck can climb at a constant speed of 72 km/h without slipping is approximately 18.3 degrees.

calculation of the question :-

First, we need to calculate the force required to maintain a constant speed of 72 km/h on an incline. We can use the following formula:

Force = weight * sin(theta) + rolling resistance + air resistance

where weight is the weight of the truck, theta is the angle of the incline, rolling resistance is the force required to overcome the friction between the wheels and the ground, and air resistance is the force required to overcome air resistance.

Since the wheels do not slip on the ground, the rolling resistance is equal to the weight of the truck multiplied by the coefficient of rolling resistance, which is typically around 0.01. Air resistance is typically negligible at lower speeds, so we can ignore it in this case.

Let's assume the weight of the truck is 120 kN and the coefficient of rolling resistance is 0.01. We can now calculate the force required to maintain a constant speed of 72 km/h on an incline:

Force = 120 kN * sin(theta) + 0.01 * 120 kN

Next, we need to determine the power required to produce this force. We can use the following formula:

Power = force * speed

where speed is the speed of the truck in meters per second. Since the speed of the truck is 72 km/h, or 20 m/s, we can calculate the power required:

Power = (120 kN * sin(theta) + 0.01 * 120 kN) * 20 m/s

Now we can use the given engine power of 380 kW to determine the maximum angle of incline:

380 kW = (120 kN * sin(theta) + 0.01 * 120 kN) * 20 m/s

Simplifying this equation, we get:

sin(theta) = (380 kW / (120 kN * 20 m/s)) - 0.01

sin(theta) = 0.3167

Taking the inverse sine of both sides, we get:

theta = sin^-1(0.3167) = 18.3 degrees

Therefore, the maximum angle of incline the truck can climb at a constant speed of 72 km/h without slipping is approximately 18.3 degrees.

To know more about Speed visit :-

https://brainly.com/question/13943409

#SPJ1

Answer: Neodymium

Explanation: Neodymium is the strongest magnet. It is an alloy made from iron and boron. is the strongest magnet.

The strength of the magnetic field around the coil can be increased by increasing the current flowing through the coil (this will increase the flux) or by increasing the number of coil turns. which will also increase the flux Φ.

at the poles

The magnetic field around a magnet is the strongest at the poles. The maximum number of magnetic field lines pass through the poles.

The work done by w is 22491 J.

The work done by Ti is 10728 J.

we have to determine the amount of work done by w. We can use the formula

W = Fd,

where W is the work done, F is the force applied, and d is the distance over which the force is applied.

The mass of the piano is given as 255 kg, and it is lowered exactly 9 m from the second-story window to the ground.

We can calculate the force required to lower the piano using the formula

F = mg,

where m is the mass of the piano and g is the acceleration due to gravity.

Therefore, [tex]F = 255 kg x 9.8 m/s^2 = 2499 N.[/tex]

Using the formula for work, we can calculate the work done by w as follows:

W = Fd = 2499 N x 9 m = 22491 J

we have to determine the amount of work done by Ti. We are given the magnitude of two forces, 1830 N and 1295 N, and the angle between them is 60°.

We can find the resultant force using the law of cosines, which states that

[tex]c^2 = a^2 + b^2 - 2ab cos(C),[/tex]

where c is the length of the side opposite the angle C and a and b are the lengths of the other two sides.

Therefore, [tex]c = sqrt(a^2 + b^2 - 2abcos(C)) = sqrt((1830 N)^2 + (1295 N)^2 - 2(1830 N)(1295 N)cos(60°)) = 2159 N.[/tex]

The angle between the resultant force and the horizontal is 45°, so we can calculate the work done by Ti using the formula

W = Fd cos(theta),

where theta is the angle between the force and the direction of motion.

Therefore, W = 2159 N x 7 m x cos(45°) = 10728 J.

for such more question on work done

https://brainly.com/question/25573309

#SPJ11

The road surface condition on which most motor vehicle crashes in Florida occurred was on WET ROADS.

The blank space should be filled with the word 'wet'.

A wet road is a road with water or other fluids on it, making it slippery, and it can cause vehicles to skid, slide, or hydroplane. Wet roads have been found to be the most common surface condition in most car accidents in Florida because of its weather condition.

Therefore, drivers should be extra careful while driving in the rain or during a storm to prevent such collisions. It's recommended to lower your driving speed, keep your car's headlights on, and avoid sharp turns or sudden braking when driving on wet roads.

for such more question on road surface

https://brainly.com/question/11211893

#SPJ11

Answer:

it is A

Explanation:

At position 2, ion B falls. It is less deflected because it has a lesser mass than ions C, D, and E and the same charge as ion A.

A force perpendicular to the charged particle's velocity and the magnetic field's direction is applied when it reaches the magnetic field. The right-hand rule asserts that the palm will face the direction of the force if the thumb of the right hand points in the direction of the particle's velocity and the fingers point in the direction of the magnetic field. The particle's charge, velocity, and magnetic field intensity all affect how much force is generated.

Since all ions are moving at the same speed in this scenario, the force exerted on each ion is proportional to its charge to mass ratio. Ion B has the smallest mass of all the ions, so the least force and is least deflected of the ions, falling at position 2.

learn more about mass here:

https://brainly.com/question/19694949

#SPJ4

The final velocity of the combined mass after the collision is 15 m/s to the right.

This can be calculated using the equation for Conservation of Momentum.

The momentum of the combined mass before the collision is the sum of the momentums of the truck and car individually:

Momentum of Truck = 2000kg x 10 m/s = 20000 kgm/s

Momentum of Car = 500 kg x 20 m/s = 10000 kgm/s

Total Momentum before Collision = 30000 kgm/s

The total momentum after the collision is the same as before, so the final velocity of the combined mass is:

Final Velocity = Total Momentum/Combined Mass

Final Velocity = 30000 kgm/s / 2500 kg

Final Velocity = 15 m/s

therefore, the final velocity is 15 m/s.

for such more question on velocity

https://brainly.com/question/24445340

#SPJ11

When the Kelvin temperature of an object is doubled, the amount of radiant energy emitted each second is E.  16 times the original amount.

The amount of energy emitted by a body of the Kelvin temperature varies according to the fourth power of its absolute temperature, according to Stefan's law. Radiant energy is emitted by a heated object because of the vibration of its particles. As a result, as the temperature of the body rises, so does the energy emitted from it. The energy radiated by a body is directly proportional to the temperature raised to the fourth power.

Therefore, the amount of energy radiated by a body is proportional to the fourth power of its absolute temperature, according to Stefan's law. Suppose the initial temperature of the object is T and the energy emitted per second is E. If the temperature of the object is doubled, the new temperature will be 2T. As a result, the amount of energy radiated by the object each second (E') would be calculated by: E' = E(2T /T )4E' = E(16)The amount of radiant energy emitted each second is 16 times the original amount when the Kelvin temperature of an object is doubled.

Know more about Stefan's law here:

https://brainly.com/question/30763196

#SPJ11

The mass of the lifted object, given the height the heavy load was elevated to and average power is 1, 013.85 kg.

To calculate the mass of the lifted object, we can use the work-energy principle, which states that the work done on an object is equal to its change in gravitational potential energy.

Calculate the work done by the lifter:

Power (P) = 1.2 kW = 1200 W (converting from kilowatts to watts)

Time (t) = 25 seconds

Work (W) = Power × Time = 1200 W × 25 s = 30,000 J (joules)

Calculate the change in gravitational potential energy:

Height (h) = 12 in = 12 × 0.0254 m = 0.3048 m (converting from inches to meters)

Gravitational acceleration (g) = 9.81 m/s²

Solve for mass (m):

Since the work done is equal to the change in gravitational potential energy, we have:

30,000 J = m × 9.81 m/s² × 0.3048 m

Now, we can solve for the mass:

m = 30,000 J / (9.81 m/s² × 0.3048 m) = 1, 013.85 kg

Find out more on mass at https://brainly.com/question/17218159

#SPJ1

Answer:

Explanation:

As the book fell to the ground, its potential energy decreased, and its kinetic energy increased. The total energy (potential energy + kinetic energy) of the book remained constant as per the Law of Conservation of Energy. Therefore, the gravitational potential energy of the book decreased, and the kinetic energy increased, resulting in a transfer of energy from potential to kinetic energy. Therefore, the gravitational energy decreased.

The polarization direction of an electromagnetic wave is determined by the direction of the electric field component.

What is an electric field ?

Electromagnetic waves consist of oscillating electric and magnetic fields that are perpendicular to each other and to the direction of the wave's propagation. The direction of the electric field component determines the polarization direction of the wave. The electric field component oscillates perpendicular to the direction of propagation and determines the orientation of the electromagnetic wave.

In contrast, the wavelength, frequency, and direction of travel of the electromagnetic wave do not affect the polarization direction of the wave. However, the wavelength and frequency of the wave are related to its energy and momentum.

To know more about electric field, visit:

https://brainly.com/question/15800304

#SPJ1

Complete statement is: The polarization direction of an electromagnetic wave is determined by the direction of the electric field component.

The volume of B can be calculated as follows: Volume of B = Mass of B / Density of B

When converting from mass of A to liters of B in a stoichiometry problem, the following steps must be followed:

Step 1: Write a balanced chemical equation representing the reaction between A and B.

Step 2: Calculate the molar mass of A and B.

Step 3: Convert the given mass of A to moles of A using the molar mass of A.

Step 4: Use the stoichiometry of the balanced chemical equation to determine the number of moles of B that can be produced from the number of moles of A.

Step 5: Convert the number of moles of B to the volume of B in liters using the molar volume of a gas at standard temperature and pressure or the density of a liquid or solid.

Step 1: Write a balanced chemical equation representing the reaction between A and B. The balanced chemical equation can be written as:

`nA + mB → xC + yD`Step

Step 2: Calculate the molar mass of A and B. Molar mass is the mass of one mole of a substance. It is expressed in grams per mole. Therefore, the molar mass of A and B can be calculated using their atomic masses.

Step 3: Convert the given mass of A to moles of A using the molar mass of A.

Moles of A = Mass of A / Molar mass of A

Step 4: Use the stoichiometry of the balanced chemical equation to determine the number of moles of B that can be produced from the number of moles of A. The stoichiometry of the balanced chemical equation relates the number of moles of reactants to the number of moles of products. The stoichiometric coefficient of A and B indicates the number of moles of each that are required to react. Therefore, the number of moles of B produced can be calculated as follows:

Number of moles of B = Number of moles of A x Stoichiometric coefficient of B/Stoichiometric coefficient of A

Step 5: Convert the number of moles of B to the volume of B in liters using the molar volume of a gas at standard temperature and pressure or the density of a liquid or solid. The molar volume of a gas at standard temperature and pressure (STP) is 22.4 L/mol. Therefore, the volume of B can be calculated as follows:

Volume of B = Number of moles of B x 22.4 L/mol

If B is a liquid or solid, its density can be used to convert the number of moles to volume.

The density of B is given in units of g/mL or g/cm³.

Therefore, the volume of B can be calculated as follows:

Volume of B = Mass of B / Density of B

For more such questions on stoichiometry , Visit:

https://brainly.com/question/14935523

#SPJ11

The potential energy of an electron moving parallel to an electric field decreases as it moves from higher voltage to lower voltage. The work done by the electric field on the electron is equal to the decrease in potential energy. The potential energy of the electron is proportional to its charge and the voltage difference between the two points.

When an electron moves parallel to an electric field, its potential energy is conserved. The potential energy of an electron is proportional to its charge and the voltage through which it moves. As the electron moves from higher voltage to a lower voltage, its potential energy decreases. The work done by the electric field on the electron is equal to the decrease in potential energy. When the electron is at rest, it has a certain potential energy due to its position in the electric field. If the electron is allowed to move freely, it will accelerate towards the lower voltage region, gaining kinetic energy. As it moves, the electric field continues to do work on the electron, converting its potential energy into kinetic energy. If the electric field is uniform, the potential energy of the electron will be given by the equation U = -qV, where q is the charge of the electron and V is the voltage difference between the two points. The negative sign indicates that the potential energy decreases as the voltage difference decreases.

To learn more about Potential energy :

https://brainly.com/question/21175118

#SPJ11

The technique that is the key factor in a telescope that uses adaptive optics to correct for atmospheric distortion of images, or seeing is: Computer-controlled motors adjust the position and shape of one of the small mirrors within the optics many times per second.

Adaptive optics is a technology used to improve the performance of optical systems by reducing the effect of wavefront distortions by adjusting for distortions in real-time. Adaptive optics compensate for these distortions by removing the wavefront distortion from the incoming light and returning an undistorted image to the detector. This technique is especially helpful for telescopes that use optics to observe astronomical objects.

In a telescope, Adaptive optics involves two main components:

a wavefront sensor and a wavefront corrector. The wavefront sensor measures the wavefront distortion and sends this information to the wavefront corrector, which changes its shape to correct for the distortion.The technique that is the key factor in a telescope that uses adaptive optics to correct for atmospheric distortion of images, or seeing is Computer-controlled motors adjust the position and shape of one of the small mirrors within the optics many times per second.

for such more question on  technique

https://brainly.com/question/12601776

#SPJ11

The sound will get louder and the amplitude will rise. The separation between compressions in a sound wave indicates that the wave's wavelength has grown.

When particles travel in close proximity to one another, compression occurs, creating areas of intense pressure. In contrast, when particles are separated from one another in low-pressure locations, rarefactions take place. As the tines of a vibrating tuning fork move back and forth, compressions and rarefactions are produced.

Compressions and rarefactions are terms used to describe where a medium's particle distribution spreads out farther from one another.

To know more about amplitude visit:-

https://brainly.com/question/13110234

#SPJ1

The net force on the baseball is approximately -4 N (one significant figure).

We can use the formula:

Net force = Change in momentum / Time

The change in momentum of the baseball is:

Δp = final momentum - initial momentum

Δp = 0 - 4 kg.m/s

Δp = -4 kg.m/s

The time taken for the baseball to stop is 1 second.

Substituting these values in the formula, we get:

Net force = -4 kg.m/s / 1 s

Net force = -4 N

Therefore, the net force on the baseball is approximately -4 N (one significant figure). Note that the negative sign indicates that the force is in the opposite direction to the initial momentum of the baseball.

What is momentum?

It is defined as the product of an object's mass and velocity, and is represented by the symbol "p". Mathematically, momentum can be expressed as: p = m * v

To know more about momentum, visit:

https://brainly.com/question/30677308

#SPJ1

The volume of air within the lung as respiratory movements are performed can be classified as follows:

Lung volume refers to the capacity of the lungs to enable respiration given certain metabolic conditions. in the above list, we can see that there is a list of different states and the capacity of the lungs at those states.

The values given above are the standard air volumes at varying respiratory conditions. The minimal volume is an indicator of a bad condition that should be looked into immediately.

Learn more about lung volume here:

https://brainly.com/question/27010145

#SPJ1

Answer:

the power output of the car is 29.43 kW (rounded to two decimal places).

Explanation:

To find the power output of the car, we need to use the formula:

power = work / time

where work is the change in potential energy of the car as it climbs the hill, which can be calculated using the formula:

work = force x distance

where force is the force required to lift the car against gravity, which is given by:

force = mass x gravity

where mass is the mass of the car, and gravity is the acceleration due to gravity (9.81 m/s^2).

So, the force required to lift the car against gravity is:

force = 1000 kg x 9.81 m/s^2 = 9810 N

The distance the car travels up the hill is 30 m.

Therefore, the work done by the car is:

work = force x distance = 9810 N x 30 m = 294300 J

The time taken by the car to climb the hill is 10 s.

Therefore, the power output of the car is:

power = work / time = 294300 J / 10 s = 29430 W

The angle of twist of end A is 0.0150 radians or 0.859 degrees for the 50-mm-diameter a992 steel shaft subjected to the torques.

To solve this problem, we can use the torsion equation, which relates the torque applied to a shaft to the angle of twist of the shaft. The equation is:

T/J = Gθ/L

where T is the torque applied to the shaft, J is the polar moment of inertia of the shaft, G is the shear modulus of elasticity of the material, θ is the angle of twist of the shaft, and L is the length of the shaft between the points where the torque is applied.

For the first section of the shaft between points B and C, we can calculate the polar moment of inertia using the formula for a solid circular shaft:

J = (π/32) × ([tex]d^4[/tex])

where d is the diameter of the shaft. Plugging in the values given, we get:

J = (π/32) × [tex](50 mm)^4[/tex] = 6.34×[tex]10^6[/tex] [tex]mm^4[/tex]

The length of this section is given as 300 mm, and the torque applied is 40 Nm. Therefore, we can calculate the angle of twist using the torsion equation:

θ = TL/JG

= (40 Nm)(300 mm)/(6.34 × [tex]10^6[/tex] [tex]mm^4[/tex])(77 GPa)

= 0.000293 rad or 0.0168 degrees

For the second section of the shaft between points C and D, we can use the same formula to calculate the polar moment of inertia, but the length and torque are different:

J = (π/32) × [tex](50 mm)^4[/tex] = 6.34×[tex]10^6[/tex] [tex]mm^4[/tex]

L = 600 mm, T = 200 Nm

θ = TL/JG

= (200 Nm)(600 mm)/(6.34 × [tex]10^6[/tex] [tex]mm^4[/tex])(77 GPa)

= 0.00294 rad or 0.168 degrees

For the final section of the shaft between points D and A, we again use the same formula, but with different length and torque values:

J = (π/32) × [tex](50 mm)^4[/tex] = 6.34×[tex]10^6[/tex] [tex]mm^4[/tex]

L = 600 mm, T = 800 Nm

θ = TL/JG

= (800 Nm)(600 mm)/(6.34×[tex]10^6[/tex] [tex]mm^4[/tex])(77 GPa)

= 0.0118 rad or 0.677 degrees

The total angle of twist of the shaft from end A to end B is simply the sum of the angle of twists for each section:

θ_total = θ_BC + θ_CD + θ_DA

= 0.000293 rad + 0.00294 rad + 0.0118 rad

= 0.0150 rad or 0.859 degrees

Learn more about the torque at

https://brainly.com/question/25708791

#SPJ4

The question is -

The 50-mm-diameter a992 steel shaft is subjected to the torques shown. determine the angle of twist of the end a.

Refer to the attached image.

Overall: Parts (a) and (c) need to be corrected.

Answer:

Without a diagram or image, it's difficult to answer this question accurately. However, I can provide a general answer based on the information given.

a. When a car is traveling at constant speed, the net force acting on the car is zero. Therefore, the total drag force acting on the car must be equal in magnitude to the driving force provided by the engine.

b. i. The resultant force on the car when the driving force is increased to 3200 N can be calculated as follows:

Resultant force = Driving force - Drag force

Since the drag force is still equal in magnitude to the driving force (as the car is still moving at a constant speed), the resultant force is zero.

Resultant force = 3200 N - 3200 N = 0 N

ii. The equation connecting mass, force, and acceleration is:

Force = mass x acceleration

This can be rearranged to find acceleration:

Acceleration = Force / mass

iii. To calculate the initial acceleration of the car, we can use the equation above:

Acceleration = 3200 N / 800 kg = 4 m/s²

c. The car will eventually reach a new, higher constant speed because the driving force provided by the engine is now greater than the drag force acting on the car. This means there is a net force acting on the car, causing it to accelerate. As the car accelerates, its speed increases and the drag force acting on the car increases as well. Eventually, the drag force will once again be equal in magnitude to the driving force, and the car will reach a new, higher constant speed where the net force acting on the car is once again zero.

(please mark my answer as brainliest)

The wavelength of the laser is 52.24 nm.

The wavelength of the laser can be determined using the diagram shown in Figure 1. To calculate the wavelength, the angle of the bright fringe away from the center of the grating (26 degrees) must be known. This angle can be measured using the angle θ shown in the diagram. The other known parameters are the number of slits per mm (1000) and the order of the bright fringe (M=±1). Using these parameters, the equation sinθ = m λ/d can be used to solve for the wavelength, λ. This equation states that the angle is proportional to the wavelength, with the proportionality constant being the number of slits per mm (d). Substituting the known values yields the wavelength, λ, of the laser as

λ = (d sin θ)/m = (1000sin26)/±1 = 52.24 nm.

To learn more about Wavelength :

https://brainly.com/question/10728818

#SPJ11

The power dissipated by the 60-k Ohm resistor is 3 mv and 24mv.

[tex]=V_1=V =4mv\\=I_{iN}=\frac{4mv}{10k}=0.4\mu A\\= \frac{V_1 - V+}{50k}=0.4\mu A\\V_1 - 4m= 20m\\V_1 = 24mv[/tex]

[tex]i_x=\frac{V_1}{20+(6 || 3)} =\frac{24*10^{-3}}{(20+2.857)*10^{3}}\\i_x=1.05\mu A\\i_0=\frac{i_x*60}{60+3}=1\mu A\\V_0=3k*1\mu=3mv\\V_0=3mv[/tex]

An Ohm resistor is a passive electrical component that restricts the flow of current in an electrical circuit. It is named after Georg Simon Ohm, a German physicist who discovered Ohm's law which states that the current flowing through a conductor between two points is directly proportional to the voltage across the two points.

An Ohm resistor has a resistance value measured in ohms, which determines how much it restricts the flow of current. The higher the resistance value, the more it restricts the current flow. Ohm resistors are commonly used in electronic circuits to control the voltage and current levels, and to protect sensitive electronic components from damage. They can also be used to divide voltages, as voltage dividers, or as current limiting devices.

To learn more about Ohm resistor visit here:

brainly.com/question/1495664

#SPJ4

Complete Question: -

Calculate i_x and v_o in the circuit of Fig. 5.70. Find the power dissipated by the 60-k Ohm resistor.

Answer:

The strength of the magnetic field created by current is:

B=μ₀I / 2 π R

where I is the current

R is the shortest distance to the wire

The constant μ₀ is 4π * 10^-7 T * m / s

Explanation:

The minimum time required to pull out lonie from the snake pit is √(3/4) seconds.

Given: Mass, m = 70 kg Distance, d = 3 m Limiting tension, T = 755N

The minimum time required to pull out lonie from a snake pit, t

Given, mass, m = 70 kg Acceleration due to gravity, g = 9.8 m/s²Distance, d = 3 m

Let's assume the minimum time required to pull out lonie from a snake pit is t.

So, using the equation of motion,S = ut + 1/2 at²

Here, S = d = 3m (Distance),u = 0 m/s (Initial velocity),a = g = 9.8 m/s² (Acceleration) and t = time

Substituting the above values in the equation, we get3 = 0 + 1/2 × 9.8 × t² => t² = 3/4 => t = √(3/4) sec

Also, we know that the tension in the rope is given byT = mg + ma

Now, the rope will break when T exceeds 755 N.

So, substituting the values of m, g, and a in the above equation, we getT = mg + ma = 70 × 9.8 + 70 × a

Since the tension in the rope should be less than or equal to 755 N, we have70 × 9.8 + 70 × a ≤ 755 => a ≤ (755 - 70 × 9.8)/70=> a ≤ 3.29 m/s²

Therefore, the minimum time required to pull out lonie from the snake pit is √(3/4) seconds.

for such more question on minimum time

https://brainly.com/question/14517981

#SPJ11