Answer:
The ratio of the resistances of second coil to the first coil is the ratio of square of radius of the first coil to the square of radius of second coil.
And
The ratio of the resistances of fourth coil to the third coil is the ratio of square of radius of the third coil to the square of radius of fourth coil.
Explanation:
The resistance of the coil is directly proportional to the length of the coil and inversely proportional to the area of coil and hence inversely proportional to the square of radius of the coil.
So, the ratio of the resistances of second coil to the first coil is the ratio of square of radius of the first coil to the square of radius of second coil.
And
The ratio of the resistances of fourth coil to the third coil is the ratio of square of radius of the third coil to the square of radius of fourth coil.
Determine the values of m and n when the following average magnetic field strength of the Earth is written in scientific notation: 0.0000451 T. Enter m and n, separated by commas.
Answer:
B = 4.51×10⁻⁵ T
Explanation:
Given that,
The average magnetic field strength of the Earth is 0.0000451 T.
We need to write the value in the form of scientific notation. Any number in scientific notation is written as follows :
N=a×bⁿ
Where
n is any integer and a is a real no
So,
0.0000451 = 4.51×10⁻⁵ T
So, the required answer is equal to 4.51×10⁻⁵ T.
If you wanted to know how much the temperature of a particular piece of material would rise when a known amount of heat was added to it, which of the following quantities would be most helpful to know?
a. coefficient of linear expansion
b. specific heat
c. initial temperature
d. thermal conductivity
e. density
Answer:
Option (b) is correct.
Explanation:
The amount of heat required to raise the temperature of substance of mass 1 kg by 1 degree C, is called specific heat of the substance.
The formula of the specific heat is
H = m c (T' - T)
where, m is the mass, c is the specific heat and T' - T is the change in temperature.
So, to know the rise in temperature, by adding the known amount of heat, the specific heat is required.
So, option (b) is correct.
A circular wire loop is placed near a long, straight, current-carrying wire in which the current is either increasing or decreasing. Draw the situations in which the induced current in the loop counterclockwise?
Answer:
The induced current is counter clockwise if the current is decreasing and towards right.
Explanation:
When the current is decreasing in the wire, the direction of magnetic field at the center of the loop is outwards to the plane of paper which is given by the Maxwell's right hand thumb rule. The magnetic field is decreasing in nature.
So according to the Lenz's law, the induced current is such that which opposes the cause of its production, so that the induced current is counter clockwise.
Suppose there are 3 molecules in a container. If each molecule has a 1-in-2 chance of being in the left half of the container, what is the probability that there are exactly 2 molecules in the left half of the container?
Answer:
Total probability = 3/8
Explanation:
Below is the calculation:
Number of molecules in the container = 3
The probability of one molecule in the left half, P = 3 / 2 = 1.5 or 1/2
The probability of second molecule in the left half, P1 = (3/4)
Total probability = P x P1
Total probability = (1/2) x (3/4)
Total probability = 3/8
A homeowner has a new oil furnace which has an efficiency of 60%. For every 100 barrels of oil used to heat his house, how much (in barrels of oil) goes up the chimney as waste heat?
Answer:
below
Explanation:
what is the resistance of a bulb of 40w connected in a line of 70v
Answer:
122.5 ohm
Explanation:
Given :
P=40 w
V= 70 V
R=?
Resistance can be calculated as :
[tex]P=\frac{V^{2} }{R} \\40=\frac{(70)^{2} }{R}\\40=\frac{4900}{R} \\R=\frac{4900}{40} \\R=122.5 ohm[/tex]
Therefore, resistance of the bulb will be 122.5 ohm
A heat engine with 0.100 mol of a monatomic ideal gas initially fills a 3000 cm3 cylinder at 800 K. The gas goes through the following closed cycle Isothermal expansion to 5000 cm3 ?
Part A How much work does this engine do per cycle? Express your answer with the appropriate units. sochoric cooling to 200 K -Isothermal compression to 3000 cm3. - Isochoric heating to 800 K Value Units
Part B What is its thermal efficiency? Express your answer with the appropriate units.
Answer:
below
Explanation:
Part A) This engine works per cycle is 254.9 J.
Part B) The thermal efficiency is 23.42%
What is the thermal efficiency?The thermal efficiency of any heat engine is represented in percentage of heat energy converted into work.
For isothermal expansion, work done is
W₁ =nRT₁ x ln(V₂/V₁)
W₁ = 0.1 x 8.314 x 800 x ln(5000/3000)
W₁ = 339.8 J =Q₁
For isochoric cooling ,
W₂ =0
Q₂ =nCvdT = 0.1 x 3R/2 x (T₂-T₁)
Q₂ = -748.3 J
For isothermal compression,
W₃ =nRT₂ ln (V₄/V₃)
W₃ = 0.1 x 8.314 x 200 x ln(3000/5000)
W₃ = -84.9J
For isochoric heating
W₄ =0
Q₄ =nCvdT = 0.1 x 3R/2 x (800-200)
Q₄ = -748.3 J
Total work done in all the process W = W₁ +W₂ +W₃ +W₄
W =254.9 J
Thus, the work done is 254.9 J
Thermal efficiency = Work done/Heat taken
η = W/ Q₁ +Q₄
η = [254.9 / 339.8 +748.3 ] x 100 %
η = 0.2342 x 100 %
η = 23.42%
Thus, the thermal efficiency is 23.42%
Learn more about thermal efficiency.
https://brainly.com/question/13039990
#SPJ2
'
human activities that interfere with distribution of natural resources are contributing to the increase of earthquake risk.
Answer:
Changes in climate conditions, especially the warming of global temperatures increases the likelihood of weather-related natural disasters. ... This is most visible when seen through changes in the intensity and frequency of droughts, storms, floods, extreme temperatures and wildfires.
If the car falls down the side of the cliff, what is happening to the gravitational potential energy of the falling car? (Assume the bottom of the cliff is zero)
Answer:
Sentences with many clauses and phrases are difficult to understand because the clauses and phrases typically _____.
modify other clauses and phrases in the sentence
refer to other sentences in the passage
make it hard to determine where the sentence ends
change the intended meaning of the sentence
Explanation:
What must a plant need to produce 4 molecules of sugar?
What must a plant need to produce 4 molecules of sugar?
Answer:
To produce a single sugar molecule a plant must use a molecule of water (H2O) and carbon dioxide (CO2) and sunlight. To get 4 molecules, you simple use 4 molecules of water and 4 molecules of carbon dioxide
Which one is the dependent variable in distance, force, or work
Answer:
Distance
Explanation:
Work can be defined as the energy transferred to a physical object by exertion of a force on the object to cause a displacement of the object. Thus, work is typically done when a person or simple machine move an object over a distance through the application of a force.
Mathematically, work done is given by the formula;
[tex] W = F * d[/tex]
Where,
W is the work done
F represents the force acting on a body.
d represents the distance covered by the body.
A dependent variable is the event expected to change when an independent variable is manipulated.
Hence, distance is the dependent variable because its value changes with respect to the amount of force exerted on an object.
What does a model of a light wave tell us about
brightness and color?
Answer:
A wave model of light is useful for explaining brightness,color, and the frequency-dependent bending of light at a surface between media. However, because light can travel through space, it cannot be a matter wave, like sound or water waves.
Which of the following phenomenon odd called photoelectric effect?
A. High energy electrons impinge on a metallic Annie which emits electrons
B. A high energy photon emits photons as it slows down
C. A metal absorbs a quanta of light and then emits electrons
D. Two electrons are created from a quanta of light.
two electrons are created from a quanta of kight
Azam had a metal pencil box and a wooden block on his table. When he touched them, the pencil box felt colder compared to the wooden block. When he measured their temperatures using a thermometer, he found that both the objects were at the same temperatures. What could be the reason for Azam to 'feel' that the pencil box was cooler? * (1 Point) Air around the pencil box was at a lower temperature which made the pencil box colder Wood produces heat and so, must have been at a higher temperature than the pencil box As metal is a better conductor of heat, it drew away heat from his hand faster than the wooden block. Metals are always at a lower temperature than other substances and so, there has been an error in measurement
The third choice is the correct explanation. Don't make me type it all out on my phone.
An iron nail floats in mercury and sinks in water. explain why?
Answer:
because density of iron is more than that of water but less then that of Mercury
hope it's helpful
calculate the electric potential 3mm from a point charge of 16Nc
[tex]4.8 \times 10^8[/tex] volts
Explanation:
The electric potential due to a point charge is given by
[tex]V= \dfrac{1}{4 \pi \varepsilon_{0}} \dfrac{Q}{r}[/tex]
where Q = charge = [tex]16 \times 10^{-9}[/tex] C
r = distance from a point = [tex]3 \times 10^{-3}[/tex] m
[tex]\varepsilon_{0}[/tex] = permitivity of free space
= 8.85×10^-12 C^2/N-m^2
Plugging in the numbers,
[tex]V = \dfrac{1}{4 \pi (8.85 \times 10^{-12})} \dfrac{16 \times 10{-9}}{3 \times 10^{-3}}[/tex]
[tex]= 4.8 \times 10^8[/tex] volts
When you release some of the paint from a spray paint can and the can remains at the same temperature, which gas law does this represent?
Answer:
Boyle's law.
Explanation:
Robert Boyle was an Irish chemist and is famously referred to as the first modern chemist. He was born on the 25th of January, 1627 in Lismore, Ireland and died on the 31st, December 1691, London, United Kingdom.
Boyles states that when the temperature of an ideal gas is kept constant, the pressure of the gas is inversely proportional to the volume occupied by the gas.
Mathematically, Boyles law is given by;
[tex] PV = K[/tex]
[tex] P_{1}V_{1} = P_{2}V_{2} [/tex]
Where;
P1 is the original pressure.
P2 is the final pressure.
V1 is the original volume.
V2 is the final volume.
Hence, when you release some of the paint from a spray paint can by applying an amount of pressure and the can remains at the same temperature, the gas law which this represent is Boyle's law.
40 ohms
1.2 A
40 ohms
12 V
Calculate the total energy developed in 5
minutes by the system above.
Answer:
17280 J and 1080 J
Explanation:
Given :
R= 40 ohm
I=1.2A
t= 5 min=60×5=300 sec
Now,
Total energy can be calculated as:
[tex]E=I^{2} Rt\\E=(1.2)^{2} *40*300\\E=17280 J[/tex]
Now,
V=12V
R=40 Ohm
[tex]E=\frac{V^{2} }{R} *t\\E=\frac{(12)^{2} }{40} *300\\E=1080 J[/tex]
Total energy is 17280 J and 1080 J
A 3-kg projectile is launched at an angle of 45o above the horizontal. The projectile explodes at the peak of its flight into two pieces. A 2-kg piece falls directly down and lands exactly 50 m from the launch point. Determine the horizontal distance from the launch point where the 1-kg piece lands.
1517.4 m
Step-by-step explanation:
Since the projectile broke up at the peak of its flight, it already traveled half its initial range so we can find its initial launch velocity [tex]v_0[/tex] from the equation
[tex]\frac{1}{2}R= \dfrac{1}{2} \left(\dfrac{v_0^2}{g}\sin 2\theta_0 \right)[/tex]
where [tex]\theta_0 = 45°[/tex] and [tex]\frac{1}{2}R = 50\:\text{m}[/tex] so we will get [tex]v_0=31.3\:\text{m/s}[/tex]. Next, we can use the equation
[tex]v_y = v_0y - gt = v_0 \sin 45 - gt[/tex]
and since [tex]v_y=0[/tex] at its peak, we get t = 22.1 s. Let's set this aside for a moment and we'll use it later.
At the top of its peak, we can use the conservation law of linear momentum. Let M be the mass if of the original projectile, [tex]m_1[/tex] be the mass of the larger fragment (2 kg) and [tex]m_2[/tex] be the mass of the smaller fragment (1 kg). We can write the conservation law as
[tex]Mv_0x = m_1V_1 + m_2V_2[/tex]
where [tex]V_1\:\text{and}\:V_2[/tex] are the velocities of the fragments immediately after the break up. But we also know that [tex]V_1=0[/tex] so the velocity of [tex]m_2[/tex] can be calculated from the conservation law as
[tex]Mv_0 \cos 45° = m_2V_2[/tex]
or
[tex]V_2 = \dfrac{M}{m_2}v_0 \cos 45° = 66.4\:\text{m/s}[/tex]
Now we can calculate the horizontal distance the smaller fragment traveled after the break up. Recall that the amount of time for it to go up is also the amount of time to get down so the horizontal distance x is
[tex]x = V_2 t = (66.4\:\text{m/s})(22.1\:\text{s})= 1467.4\:\text{m}[/tex]
Therefore, the total distance traveled from the launch point is
[tex]D = 50\:\text{m} + 1467.4\:\text{m}=1517.4\:\text{m}[/tex]
help plzzzzzzzzzzzz ?
Explanation:
1. First, let's find the total resistance of the circuit. We begin by combining [tex]R_{4}[/tex], [tex]R_{5}[/tex] and [tex]R_{6}[/tex]:
[tex]R_{456}=R_{4} + \dfrac{R_{5}R_{6}}{R_{5} + R_{6}}[/tex]
[tex]= 6\:Ω + \dfrac{(3\:Ω)(5\:Ω)}{3\:Ω+5\:Ω} = 7.9\:Ω[/tex]
Now time to combine [tex]R_{2}[/tex] and [tex]R_{3}[/tex] and they are connected in series so
[tex]R_{23} =R_{2} + R_{3} = 17\:Ω[/tex]
Note that [tex]R_{23}[/tex] and [tex]R_{456}[/tex] are connected in parallel so
[tex]R_{23456} = \dfrac{R_{23}R_{456}}{R_{23}+R_{456}}=5.4\:Ω[/tex]
Finally, [tex]R_{23456}[/tex] is connected in series with [tex]R_{1}[/tex] so the total resistance [tex]R_{T}[/tex] is
[tex]R_{T} = R_{1} + R_{23456} = 10\:Ω + 5.4\:Ω = 15.4\:Ω[/tex]
2. The total current in the circuit is
[tex]I_{T} = \dfrac{V}{R_{T}} = \dfrac{20\:V}{15.4\:Ω} = 1.3\:A[/tex]
3. The voltage drop across [tex]R_{1},\:V_{1}[/tex] is
[tex]V_{1} = I_{T}R_{1} = (1.3\:A)(10\:Ω) = 13\:V[/tex]
4. We can see that [tex]I_{T} = I_{1} + I_{2}[/tex]. To solve for [tex]I_{1}[/tex], we need [tex]V_{23}[/tex], which is just [tex]V_{T} - V_{1} = 20\:V - 13\:V = 7\:V[/tex] , which gives us
[tex]I_{1} = \dfrac{V_{23}}{R_{23}} = \dfrac{7\:V}{17\:Ω} = 0.4\:A[/tex]
5. From #2 & #4, [tex]I_{2} = 1.3\:A - 0.4\:A = 0.9\:A[/tex] and we also know that the voltage drop across [tex]R_{456}[/tex] is 7 V, the same as that of [tex]R_{23}[/tex]. The voltage drop across [tex]R_{4}[/tex] is
[tex]V_{4} = I_{2}R_{4} =(0.9\:A)(6\:Ω) = 5.4\:V[/tex]
This means that the voltage drop across [tex]R_{6}[/tex] is 7 V - 5.4 V = 1.6 V. Knowing this, the current through [tex]R_{6}[/tex] is
[tex]I_{6} = \dfrac{1.6\:V}{5\:Ω} = 0.3\:A[/tex]
Calculate the terminal velocity of a rain drop of radius 0.12cm
Explanation:
Given that,
The radius of rain drop, r = 0.12 cm = 0.0012 m
The viscocity of air is, [tex]\eta=18\times 10^{-5}\ poise[/tex]
Let the viscous force is, [tex]F = 0.010173\ N[/tex]
The viscous force is given by :
[tex]F=6\pi \eta rv\\\\v=\dfrac{F}{6\pi \eta r}[/tex]
Put all the values,
[tex]v=\dfrac{0.010173}{6\pi 18\times 10^{-5}\times 0.0012 }\\\\v=2498.58\ m/s[/tex]
Một ô tô khối lượng một tấn chuyển động trên một đường nằm ngang. Hệ số ma sát giữa bánh ô tô và mặt đường là 0,07. Gia tốc trọng trường g=9,8m/s2
a) vẽ và xác định tên các lực tác động lên vật. Viết phương trình chuyển động của vật.
b) nếu ô tô chuyển động đều, xuống dốc có độ dốc 5%. Tính lực kéo của ô tô.
c) nếu ô tô chuyển động đều. Lên dốc có độ dốc 5%. Tính lực kéo của động cơ ô tô
If a rock displaces 7 ml of water, what is the volume of the rock?
Answer:
if i am not mistaken the volume is 7, because it only took that much space
What is a reasonable measurement for the distance to Neptune?
30 light years
30 kilometers
30 parsecs
30 Astronomical Units
Answer:
30 kilometers is a reasonable measurement
12) A negatively-charged balloon touching a wooden wall
A) pulls positive charge on the wall surface toward it.
B) pushes negative charge in the wall away from it.
C) polarizes molecules in the wall.
D) all of the above.
Answer:
D) all of the above.
Explanation:
First polarises it, cahrging and discharging occurs at once.
A negatively charged balloon touching a wooden wall then from the given options option D is correct which is all of the above.
What is a charge?Charged matter experiences a force when it is exposed to an electromagnetic field due to the physical property of electric charge. Positive or negative charges can exist in an electric field (commonly carried by protons and electrons, respectively).
Contrary charges attract one another, while like charges repel one another. A neutral object is one that carries no net charge. Classical electrodynamics, the name given to an early understanding of how charged particles interact, is still accurate for issues that do not call for taking into account quantum phenomena.
In the first step it polarizes molecules in the wall, then charging and discharging in the wall will take place at once.
To get more information about Charge :
https://brainly.com/question/19886264
#SPJ2
Khối lượng ban đầu của mặt trời m⊙ = 2 × 1030 kg trong đó có 71 % là
hydrogen. Trong 5×10^9 năm đầu tiên, mặt trời phát ra năng lượng với công suất
3.86 × 10^26 W, nhờ phản ứng
4p → 4+2He + 2e
+ 2νe + 26 MeV
trong đó bốn proton tổng hợp thành hạt α và tỏa ra năng lượng 26 MeV. Hãy
xác định
a) số hạt proton của mặt trời tại thời điểm ban đầu.
b) số hạt proton của mặt trời tham gia phản ứng trong 1 năm.
c) số hạt proton còn lại trong mặt trời sau 5 × 10^9 năm.
d) thời gian để tiêu thụ hết 10 % số hạt proton còn lại của mặt trời
Answer:
jsgssbvwsvs
Explanation:
ifmd understand
What is the magnitude of a vector that has the following components: x = 32 m y = -59 m
Answer:
Explanation:
Since the x and y components are given
The vectors Magnitude = √32²+(-59)²
=67.12m
Một vật chuyển động tròn đều có chu kì T = 0,25 s. Tính tần số chuyển động f của vật?
Explanatio
omega=2pi/T
Answer:
0
0000
Explanation:
Convert Rev/min to rad/s x 2pie/60?
Anyone knows this please?
Answer:
Thus, [tex]\frac{1 rev}{min} =\frac{2\pi}{60} rad/s[/tex]
Explanation:
The angular speed is defined as the rate of change of angular velocity.
Its SI unit is rad/s and other units are rev/min or rev/s.
[tex]\frac{1 rev}{min } = \frac{1 rev}{60 sec}\\\\1 rev = 2\pi rad\\\\So\\\\\frac{1 rev}{min} = \frac{2\pi}{60} rad/s[/tex]
A 10,000J battery is depleted in 2h. What power consumption is this? *
A) 5000W
B) 3W
C) 1.4W
D) 20000W
show your work please
Answer:
P = 1.4 W
Explanation:
Given that,
The work done or the energy of the battery, E = 10,000 J
Time, t = 2 h
We need to find the power consumption. Let it is P. Power is the rate of doing work. So,
[tex]P=\dfrac{W}{t}\\\\P=\dfrac{10,000}{2\times 3600}\\\\P=1.38\ W[/tex]
or
P = 1.4 W
So, the power of the battery is 1.4 W.
