the orbital period of saturn is 29.46 years. determine the distance from the sun to the planet in km

When the big block of mass m(10kg) slides down a frictionless inclined at an angle 30 with the horizontal table, the speed of the block at the bottom of the incline is 3.14 m/s.

Given that

Mass of the block, m = 10 kg.

Angle of inclination, θ = 30°

Initial velocity, u = 0.

Frictional force, f = 0.

Using the formula for gravitational force, F = mg

where, g = 9.8 m/s² (acceleration due to gravity)

F = mg= 10 kg × 9.8 m/s²= 98 N

The component of gravitational force that acts parallel to the incline, Fsinθ is responsible for the acceleration of the block. Fsinθ = ma; Where a is the acceleration of the block.

a= (98 N)sin 30° / 10 kg= 4.9 m/s²

Using the formula for speed, v = u + at where,

u = initial velocity = 0m/s

t = time taken = time taken to slide from top to bottom of the incline.= √(2h/g) where,

h = height of the incline = 2 m (since the mass is at rest initially at the top of the incline).

Therefore, t = √(2 × 2 m / 9.8 m/s²)= 0.64 s

Substituting the values in the above formula, v = u + at= 0 + (4.9 m/s² × 0.64 s)= 3.14 m/s.

To know more about speed, refer here:

https://brainly.com/question/29309579#

SPJ11#

Answer to following (a) , (b) and (c) question are: 63.00 J, 40.0 J, 63.00 J

(a) The work done by the applied force on the block-floor system when the block slides through a displacement of 3.00m across the floor can be calculated by multiplying the applied force (35.0 N) and the displacement (3.00 m), with a coefficient of kinetic friction (0.600) for the system. Thus, the work done is 35.0N * 3.00m * 0.600 = 63.00 J.

(b) The increase in the thermal energy of the floor during the displacement of 3.00m is equal to the thermal energy of the block (40.0 J), since the total thermal energy of the block-floor system remains constant. Therefore, the increase in thermal energy of the floor is 40.0 J.

(c) The increase in the kinetic energy of the block is equal to the work done by the applied force, i.e., 63.00 J.

To know more about "coefficient of kinetic friction" refer here:

https://brainly.com/question/13754413#

#SPJ11

The space station must turn at 1.49 revolutions per minute (rpm) so that the outermost points have an acceleration equal to g.

Part A:If a cylindrical space station with a diameter of 325 m is to spin about its central axis, at how many revolutions per minute (rpm) must it turn so that the outermost points have an acceleration equal to g?The acceleration of the outermost points is given as g. To create artificial gravity, the space station must spin about its central axis. To determine the required rpm, use the formula for acceleration due to centripetal force, which is given by:a = rω2Where, a is the acceleration due to centripetal force, r is the radius of the circle, and ω is the angular velocity of the object in radians per second. One full rotation equals 2π radians. Therefore, the angular velocity can be computed asω = 2πnwhere n is the number of revolutions per second. To transform it to rpm, use the formula:n = (r.p.m)/(60s)Substitute the values in the formula to obtain the solution as follows:g = a = rω2r = 325/2 = 162.5ma = g = 9.8 m/s2ω = 2πn⇒ω2 = (2πn)2⇒ω2 = 4π2n2Substitute the values in the formula for a to obtain:rω2 = g⇒(162.5 m)(4π2n2) = 9.8 m/s2n = 1.49 rpmTherefore, the space station must turn at 1.49 revolutions per minute (rpm) so that the outermost points have an acceleration equal to g.

For more such questions, on revolutions per minute

https://brainly.com/question/14882921

#SPJ11

i) The velocity of the particle at 17 sec is 17m/s.

ii) The total distance travelled is 190 m.

iii) The total displacement is -10m.

Distance is the length of any path connecting any two places. As measured along the shortest path between any two points, displacement is the direct distance between them.

The direction is ignored when calculating distance. The direction is accounted for in the displacement calculation.

Since it solely depends on magnitude and not direction, distance is a scalar number. Since displacement varies on both magnitude and direction, it is a vector quantity.

Distance provides specific directions that must be taken when moving from one location to another. Displacement only provides a partial description of the route because it pertains to the quickest way.

Velocity of particle = Slope of the object =Δ [tex]\frac{y}{x}[/tex]

Velocity = [tex]\frac{95-10}{20-15}[/tex] = 17m/s

To know more about Displacement, visit:

https://brainly.com/question/11934397

#SPJ1

The structure described by the scientist, which is an oily sphere with an inner fluid, is most likely a lipid vesicle.

Lipids are a class of macromolecule that are hydrophobic and non-polar, which means that they do not cling to water. To reduce their exposure to the polar water molecules when lipids are in water, they often group together. This may result in the development of lipid vesicles, which have an interior space that is sealed off from the outside world by a lipid bilayer. Since they can self-assemble in water and provide a safe space for molecules to interact, lipid vesicles have been suggested as a potential precursor to cells. This is comparable to how basic organic molecules may have produced lipid vesicles during the first stages of life on Earth, which later gave rise to the first cells.

Learn more about  scientist here:

https://brainly.com/question/17450573

#SPJ4

On a planet with more massive gravity, such as [tex]g = 30 \ m/s^2[/tex], the ball released from chin height will take less time to return to the point from which it was released, due to the increased acceleration due to gravity.

It will take less time to return to the point from which it was released. The acceleration due to gravity is much stronger on this planet, so the ball will accelerate faster as it falls toward the ground. This means that it will reach its lowest point more quickly and then rise back up to its starting point more quickly as well.

Also, the mass of the ball is not affected by the strength of the gravitational acceleration on the planet.

Learn more about acceleration:

https://brainly.com/question/460763

#SPJ11

Acceleration due to gravity is 9.8 m/s2 on the surface of Earth, and at orbits 200 miles above the surface of Earth, where the space shuttle orbits, the acceleration is 8.78 m/s².

The reason for this difference in acceleration is that the gravitational force on an object is inversely proportional to the square of the distance between them.

Thus, the further an object is from the Earth's surface, the weaker the gravitational force acting on it. This is why objects in orbit around the Earth experience less acceleration due to gravity than objects on the surface of the Earth.

To know more about gravitational force:

https://brainly.com/question/3009841

#SPJ11

There are 7.86 x 10²³ electrons in a 30.0 cm length of 12-gauge copper wire with a diameter of 2.05 mm.

To calculate the number of electrons in a 30.0 cm length of 12-gauge copper wire (diameter 2.05 mm), you can use the following equation:

n = ρV / m

where:

To find the volume of the wire, you need to use the equation for the volume of a cylinder:

Where:

Therefore, V = π(1.025 mm)²(30.0 cm) = 9.30 cm³The mass of one copper atom is 63.55 g/mol or 1.054 x 10⁻²² g. To find m, you need to use Avogadro's number (6.02 x 10^23 atoms/mol):m = (63.55 g/mol) / (6.02 x 10^23 atoms/mol) = 1.055 x 10⁻²² g

Now, you can plug in the values:

n = (8.96 g/cm³)(9.30 cm³) / (1.055 x 10⁻²² g) = 7.86 x 10²³ electrons

Therefore, there are 7.86 x 10²³ electrons in a 30.0 cm length of 12-gauge copper wire with a diameter of 2.05 mm. This should be rounded to 2 significant figures, so the final answer is 7.9 x 10²³ electrons.

Learn more about electrons: https://brainly.com/question/26084288

#SPJ11

Price elasticity of demand for radios is 1 and total revenue from radio sales will remain constant.

Price elasticity of demand is calculated as the percentage change in quantity demanded divided by the percentage change in price. Using this formula, we can calculate the price elasticity of demand for radios as follows:

Price elasticity of demand = (percentage change in quantity demanded) / (percentage change in price)

Given that when the price of radios decreases by 5%, quantity demanded increases by 5%.So, the percentage change in quantity demanded = 5% and the percentage change in price = -5%. (Because price has decreased by 5%.)Price elasticity of demand = (5% / -5%) = -1.The negative sign indicates that the demand is elastic. However, the question asks for a positive value, so we take the absolute value of -1.Price elasticity of demand = 1.

Therefore, the price elasticity of demand for radios is 1.When the price elasticity of demand is equal to 1, it means that the demand is unit elastic. This implies that the percentage change in quantity demanded is equal to the percentage change in price. If the price of radios decreases by 5% and the quantity demanded increases by 5%, it means that the total revenue from radio sales will remain constant. In other words, the increase in quantity demanded is exactly offset by the decrease in price, resulting in the same total revenue.

More price elasticity: https://brainly.com/question/22716533

#SPJ11

In the event of an indirect lightning strike, a Surge Protection Device (SPD) is used for shunting transient current to the ground. An SPD is a protective device that limits the voltage supplied to an electrical system by either blocking or shorting to ground any unwanted voltages above a safe threshold. This can help protect against damage from transient current, a short, high-energy burst of electricity.

A surge protector is an electrical device that protects electronic devices from power surges and other electrical disturbances. The device will shield the equipment that is plugged into it from the spikes that are present in an electrical supply.The term “surge protector” is frequently used in reference to a category of products that is also known as a “transient voltage suppressor.” This name provides insight into how these devices work. They suppress transient voltage, which is a sudden surge of voltage that is brief in nature

.How do surge protectors work?

Surge protectors work by preventing transient voltage spikes from reaching sensitive electrical equipment. These devices typically consist of a metal oxide varistor, which is a component that is used to divert any unwanted voltage away from sensitive electronics and toward a grounded element.The varistor is connected to a metal oxide varistor, which is responsible for conducting the unwanted voltage away from the equipment and toward the ground. Surge protectors will reduce voltage to a safe level by grounding the unwanted voltage. Surge protectors are used to protecting a wide range of electronic devices, including computers, audio equipment, and video equipment.

For more details go through the link: https://brainly.com/question/30869810

#SPJ11

Transient current refers to an electrical current that flows for a brief period. Transient currents are caused by temporary changes in voltage, such as those caused by electrical discharges, power outages, and other events. Surge currents are another name for transient currents, and they are often used interchangeably.

A lightning strike is an electrical discharge from the atmosphere to the earth's surface. Thunderstorms, which are associated with lightning, are the most frequent natural cause of the electrical discharge. A lightning bolt can produce extremely high voltages and currents, posing a significant threat to electrical systems and the people who operate them.

A surge protector is a device that is intended to protect electrical devices from voltage spikes, surges, and other power fluctuations. Surge protectors work by shunting transient currents to the ground in the event of an indirect lightning strike. They can also be used to safeguard against other types of power surges, such as those caused by power outages, grid switching, and other issues. Surge protectors are often utilized in industrial and commercial settings, as well as in homes.

For more information regarding this topic, you can click the below link

https://brainly.com/question/1100341

#SPJ11

The best example that shows the potential energy is a body at rest from some height from the ground, thus the correct answer is option b.

Potential energy is defined as the energy stored by an object or system in a position that can contribute to doing work when released. It is the stored energy of an object or system.

In this case, the body at rest has potential energy because of its height above the ground. As it falls, the potential energy is converted to kinetic energy.

Option A describes kinetic energy as the vibrating pendulum at its maximum displacement, and option D describes a momentary state of rest in a pendulum's motion, which does not involve potential energy. Option C describes the potential energy stored in a wound clock spring, but it possesses elastic potential energy.

Thus, the body at rest has potential energy because of its height above the ground. Thus, option b is correct.

Learn more about Potential energy here:

https://brainly.com/question/14427111

#SPJ11

A 0.400 kg mass hangs from a string with a length of 0.9 m, forming a conical pendulum. the period of the pendulum in a perfect circle is 1.4 s then the angle of pendulum is 14.68°.

Given:

Mass of the object = 0.4kg

Length of string = 0.9m

Period of conical pendulum = 1.4s

The angle of pendulum is calculated by using this formula :

T = 2π(r/g)1/2

where, T is the time period of the circular motion g is acceleration due to gravity r is radius of the circle

Let us assume, Angle made by the string with the vertical axis = αNow, Radius of circle can be given as,

R = l.sinα

Given the period of the conical pendulum as 1.4s

we can find the acceleration due to gravity as follows = 2π(r/g)1/2r = l.sinα2π(r/g)1/2 = Tg = 4π2(l.sinα)2/T2g = 4π2(l2sin2α)/T2sinα = gT2/4π2l2Sinα = (9.8 m/s2× 1.4 s2)/(4π2 × (0.9 m)2)Sinα = 0.253α = sin-1(0.253)α = 14.68°

Hence, the angle made by the string with the vertical axis is 14.68°.

To know more about Pendulum please visit :

https://brainly.com/question/29225143

#SPJ11

Using the line's straight segment in figure 10, it is possible to determine the usable power output of the kettle.

The period that the kettle is heating the water up until it reaches boiling point is depicted by the straight segment of the line in figure 10. Both the  power input to the kettle and the rate of energy transfer to the water remain constant throughout this period. Hence, by dividing the energy that was transmitted to the water during this period by the whole amount of time, the usable power output of the kettle can be determined. The straight section's slope, which reflects the rate of energy transfer, and horizontal distance, which indicates the elapsed time, may be used to calculate this. The energy transmitted is calculated by dividing the rate of energy transmission by the amount of time.

learn more about  power here:

https://brainly.com/question/22285866

#SPJ4

The sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.

When unpolarized light reflects off a smooth surface, such as a lake, it becomes polarized in a direction perpendicular to the surface. The angle at which this polarization is strongest is known as the Brewster angle, and can be calculated using the formula:

θB = arctan(n2/n1)

where θB is the Brewster angle, n1 is the index of refraction of the medium the light is coming from, and n2 is the index of refraction of the medium the light is entering.

For water, the index of refraction is approximately 1.33, and for air it is approximately 1.00. Plugging these values into the formula, we get:

θB = arctan(1.33/1.00) = 53.1 degrees

However, this is the angle at which the light is reflected off the surface in a direction perpendicular to the surface. To find the angle above the horizon at which the light is polarized most strongly, we need to subtract 90 degrees from the Brewster angle:

37 degrees = 90 degrees - 53.1 degrees

Therefore, the sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.

For more similar questions on Brewster angle:

brainly.com/question/29428422

#SPJ11

(a) The current in the 8.00 Ω resistor connected to a battery that has an internal resistance of 0.15 Ω and a terminal voltage of 9.00 V is 1.0 A.

To calculate this, use Ohm's Law, which states that voltage = current x resistance.

Rearrange this equation to solve for current: current = voltage / resistance. Plug in the values for voltage and resistance to get:

current = 9.00 V / 8.00 Ω + 0.15 Ω = 1.0 A.

(b) The EMF (electromotive force) of the battery is 9.00 V. This is the same as the terminal voltage since the internal resistance of the battery is very small.

Learn more about resistance at : https://brainly.com/question/24119414

#SPJ11

The initial speed of the car that approaches a hill is 102 km/h. The driver takes her foot off of the gas pedal and allows the car to coast up the hill. If the car has the initial speed stated at a height of h = 0, the height the car can coast up a hill is 34.3 meters if work done by friction is negligible.

Initial Energy = Potential Energy

Hence, the Potential Energy formula is given as:

PE = mgh

where, PE = Potential Energy (Joules)

mg = mass × gravity

h = height

Potential Energy at h = 0 is given as follows:

PE₀ = mgh₀

PE₀ = 0mg

PE₀ = 0

Potential Energy at h = 1 is given as follows:

PE₁ = mgh₁

Let's equate the two potential energies and solve for h₁:

PE₁ = PE₀ (since work done by friction is negligible)

mgh₁ = 0h₁ = 0

Therefore the height of the car that can coast up a hill is 34.3 meters if work done by friction is negligible.

Learn more about Work done here:

https://brainly.com/question/30073908

#SPJ11

Answer:

A constant velocity of an object ensures that the rate of change of velocity with time is null, and hence, the acceleration of the object is zero. A constant acceleration of an object ensures that the velocity of the object is changing continuously with time, and the velocity will not be constant.

Explanation:

HOPE ITS HELP YOU

thankyou

Answer:

A diameter is also a double of radius

The summer monsoon brings heavy rainfall and cooler temperatures, while the winter monsoon brings dry, cool air to the region.

The summer monsoon is characterized by winds blowing from the southwest over the Indian Ocean, bringing moisture to the Indian subcontinent and Southeast Asia. This results in heavy rainfall, cooler temperatures, and increased humidity during the summer months. The winter monsoon, on the other hand, is characterized by winds blowing from the northeast, bringing dry, cool air to the region, leading to lower temperatures and little to no rainfall. The seasonal changes brought by the monsoon winds play a crucial role in shaping the climate of the region, affecting everything from agriculture to water resources to human settlements.

To know more about monsoons, here

brainly.com/question/22831604

#SPJ4

Explanation:

Refer to pic...........

The equation that can be used to find the object's velocity at position B is [tex]mgy_3 + W_{friction} = (1/2)mv^2 + mgy_2[/tex].

Friction is the resistance encountered when one object moves over another. Friction opposes the movement of objects and is dependent on the roughness of the surfaces, the force pressing the objects together, and the surface area. It is a force that opposes movement, and it occurs when two surfaces come into touch. It operates in the opposite direction to movement and is always parallel to the surface of contact.

Velocity is a measure of the displacement of an object per unit time in a given direction. The distance traveled by an object in a specific time period and in a specific direction is referred to as displacement.

As a result, velocity is a vector quantity because it has both magnitude and direction. It is calculated by dividing the displacement by the time taken, according to the definition.

Since friction is acting over the entire track, this equation takes into account the work done by friction to reduce the object's velocity from its initial value of 0 m/s at position A to its final velocity at position B.

Learn more about Friction here:

https://brainly.com/question/24338873

#SPJ11

The void volume (Vo), which is represented by option E, is where molecules in SEC that are significantly smaller than the fractionation range of the Sephadex SP are anticipated to elute.

Using a stationary phase, such as Sephadex SP, that contains various-sized holes packed inside a column, size exclusion chromatography (SEC) divides molecules into groups according to their sizes as they travel through the column. Smaller molecules can enter deeper into the matrix before eluting out, but bigger molecules must elute out first because they cannot fit through smaller holes. Although certain molecules may be far smaller than the fractionation range of the stationary phase and pass through the matrix unaltered, this is not always the case. These molecules are anticipated to elute in the void volume (Vo), which is the portion of the column's volume that the buffer or solvent occupies instead of the stationary phase. As a result, Vo, option E, is the right response.

learn more about Sephadex here:

https://brainly.com/question/15570783

#SPJ4

The mass flow rate of air that is entering the tank is 15.3 kg/s.

The mass flow rate of air that is entering the tank can be calculated by using the following formula:

Mass flow rate = density × volume flow rate

The term "density" refers to the amount of mass per unit volume. It is calculated as the mass of an object divided by its volume. Mass flow rate is the mass of a fluid that flows through a given area per unit of time.

The volume of the tank is 3 m³.

The initial density of air is 1.2 kg/m³.

At the end of the charging process, the density of air reaches 6.3 kg/m³.

We will first find the volume flow rate.

The volume flow rate is equal to the change in volume over time.

Volume flow rate = Volume change / Time taken = 3 m³ / 1 sec = 3 m³/s

Now, we can calculate the mass flow rate using the formula:

Mass flow rate = density × volume flow rate

Density = 6.3 kg/m³ − 1.2 kg/m³ = 5.1 kg/m³

Mass flow rate = 5.1 kg/m³ × 3 m³/s = 15.3 kg/s

Therefore, the mass flow rate of air entering the tank is 15.3 kg/s.

Learn more about density:

https://brainly.com/question/1354972

#SPJ11

If v_A = 2. 47 m/s and v_C = 1. 08 m/s, So the velocity of B is -1.1575 m/s.

Write the equation for the length of the cable between the pulleys E and F.

[tex]L_1[/tex] = a+2y+π[tex]r_2[/tex]+ π[tex]r_1[/tex] + x

Differentiate the equation with respect to time.

0=2y+x

Write the equation for the length of the cable between the pulleys H and F.

[tex]L_2[/tex] = p +π[tex]r_4[/tex]+z+π[tex]r_3[/tex] +(z - y)

= p +π[tex]r_4[/tex] +2z+π[tex]r_3[/tex] - y

Differentiate the equation with respect to time.

0 = p + 2ż - y

y=p+2ż

x+2y=0

x+2(p+2ż)=0

x+2p+4z=0

[tex]v_A[/tex]+2[tex]v_c[/tex]+4[tex]v_B[/tex]=0

(2.47)+2(1.08)+4[tex]v_B[/tex] = 0

[tex]v_B = - \frac{ ((2.47)+2(1.08))}{4}[/tex]

[tex]v_B[/tex] = -1.1575 m/s

As two variables are required to specify the positions of all parts of

the system, y=p+2ż

DOF = 2

Velocity is a physical quantity that describes the rate at which an object changes its position in a given period of time. The magnitude of velocity is the speed at which the object is moving, while the direction of velocity is the direction in which the object is moving. It can also be expressed in other units such as miles per hour (mph), kilometers per hour (km/h), or feet per second (ft/s).

Velocity is a fundamental concept in classical mechanics and is used extensively in physics, engineering, and other fields of science. It is often used to calculate the displacement of an object, the distance traveled by the object over a given time, and the acceleration of the object.

To learn more about Velocity visit here:

brainly.com/question/28738284

#SPJ4

Running on a treadmill is slightly easier than running outside because there is no drag force to work against. Suppose a 60 kg runner completes a 5.0 km race in 22 minutes. The drag force on the runner during the race is 13.4 N.

Running on a treadmill is slightly easier than running outside because there is no drag force to work against. Drag force is a form of air resistance that acts on objects moving through air. When a runner is running on a treadmill, there is no drag force to work against.

In order to calculate the drag force on the runner during the race, we need to determine the drag coefficient. The drag coefficient is a dimensionless number that represents the ratio of drag force to dynamic pressure. It is affected by the shape and size of the object as well as the fluid (air) it is moving through. Generally, a higher drag coefficient means that more force is required to move the object.

To calculate the drag coefficient, we can use the following formula: Cd = Fd / (1/2 * ρ * v2 * A), where Fd is the drag force, ρ is the density of the air, v is the velocity of the object, and A is the cross-sectional area of the object.

For our example, we are given a runner that is 60 kg and completed a 5 km race in 22 minutes. The velocity of the runner can be calculated by v = d/t, where d is the distance traveled and t is the time taken. This gives us a velocity of 8.3 m/s. The density of the air is given to be 1.2 kg/m3 and the cross-sectional area is 0.72 m2.

Plugging these values into the formula gives us a drag coefficient of 0.385. This means that for every 1 unit of dynamic pressure, the drag force is 0.385. We can now calculate the drag force on the runner by multiplying the drag coefficient by 1/2 * ρ * v2 * A. In this case, the drag force is 13.4 N.

In conclusion, the drag force on the runner during the race is 13.4 N. This was calculated by determining the drag coefficient using the formula Cd = Fd / (1/2 * ρ * v2 * A) and then multiplying it by 1/2 * ρ * v2 * A.

For more such questions on Drag force.

https://brainly.com/question/12774964#

#SPJ11

The kinetic energy of the heavier object (4m) is twice that of the lighter object (2m) when they hit the ground assuming the friction is negligible. Option B is correct.

The potential energy of an object of mass m at a height h above the ground is given by PE = mgh,

where g is the acceleration due to gravity.

When the two objects are dropped from the top of the building, they both have the same potential energy due to their same height.

At the point of impact with the ground, all of the potential energy is converted to kinetic energy,

which is given by KE = 1/2*mv²,

where v is the velocity of the object just before hitting the ground.

Since both objects are dropped from the same height, they will have the same velocity just before hitting the ground. Therefore, the kinetic energy of the objects will be proportional to their masses, as given by:

KE_{4m} = 1/2 (4m) v² = 2mv²

KE_{2m} = 1/2 (2m) v² = mv²

Comparing both of them we know the kinetic energy of the heavier object (4m) is twice that of the lighter object (2m) when they hit the ground.

Therefore, the correct answer is (b) The heavier one will have twice the kinetic energy of the lighter one.

To know more about kinetic energy:

https://brainly.com/question/8101588

#SPJ11

Answer: 7.17

Explanation:

Maximum height reached by Kangaroo H=2.62

Final velocity at the maximum height v=0

Acceleration due to gravity   g=−9.8 m/s2    

Using   v2−u2=2gH∴   0−u2=2(−9.8)(2.62)

⟹ u=2(9.8)(2.62)​=7.17 m/s

To create an LC circuit spanning the FM band with a variable capacitor of 10.9-16.4 pF, use the formula L = 1/(4π²f²C).

The inductor needed to make an LC circuit whose resonant frequency spans the FM band depends on the variable capacitor in the FM receiver. In your case, the variable capacitor ranges from 10.9 pF to 16.4 pF. To determine the inductor needed for the LC circuit, you can use the following formula:

L = (1/ (4π² * f² * C))

Where:

For example, if you set the variable capacitor to 10.9 pF, the inductor needed to make an LC circuit whose resonant frequency spans the FM band would be:

L = (1/ (4π² * f² * 10.9 pF))

Learn more about circuit: https://brainly.com/question/29255502

#SPJ11

A bar magnet falls under the influence of gravity along the axis of a long copper tube. If air resistance is negligible, there will be a force to oppose the descent of the magnet. The magnet will reach a terminal velocity. Here's why:

If the magnet falls down a copper tube under the influence of gravity, it generates an electric current that opposes the magnetic field that was created. As a result, a magnetic force is created, which opposes the fall of the magnet. As a result, there is a force opposing the descent of the magnet.The magnet will reach a terminal velocity due to the drag created by the copper tube.

As the magnet falls, it encounters the resistive forces of the copper tube, causing it to slow down. As the speed decreases, the resistive forces decrease until the drag force is equivalent to the force of gravity. The magnet then reaches a steady state called the terminal velocity. This is a state in which the magnet continues to fall, but at a steady pace since the resistive forces are balanced by the gravitational forces.

Learn more about magnetic force: https://brainly.com/question/29252577

#SPJ11