The unit of solar radiation?

This question is incomplete, The missing image is uploaded along this answer below;

Answer:

the maximum stress in the cylinder is 3.23 ksi

Explanation:

Given the data in the question and the diagram below;

First we determine the initial Kinetic Energy;

T = [tex]\frac{1}{2}[/tex]mv²

we substitute

⇒ T = [tex]\frac{1}{2}[/tex] × (550/32.2) × (2)²

T = 34.16149 lb.ft

T =  ( 34.16149 × 12 ) lb.in  

T = 409.93788 lb.in

Now, the volume will be;

V = [tex]\frac{\pi }{4}[/tex]d²L

from the diagram; d = 0.5 ft and L = 1.5 ft

so we substitute

V =  [tex]\frac{\pi }{4}[/tex] × ( 0.5 × 12 in )² × ( 1.5 × 12 in )

V = 508.938 in³

So by conservation of energy;

Initial energy per unit volume = Strain energy per volume

⇒ T/V = σ²/2E

from the image; E = 6.48(10⁶) kip

so we substitute

⇒ 409.93788 / 508.938 = σ²/2[6.48(10⁶)]

508.938σ² =  5,312,794,924.8

σ² = 10,438,982.5967  

σ = √10,438,982.5967

σ = 3230.9414  

σ = 3.2309 ksi  ≈ 3.23 ksi    { three significant figures }

Therefore, the maximum stress in the cylinder is 3.23 ksi

Answer:

F[tex]_D[/tex] for A > F[tex]_D[/tex] for B

Hence, Bearing A can carry the larger load

Explanation:

Given the data in the question,

First lets consider an application which requires desired speed of n₀ and a desired life of L₀.

Lets start with Bearing A

so we write the relation between desired load and life catalog load and life;

[tex]F_R(L_Rn_R60)^{1/a}[/tex] = [tex]F_D(L_Dn_D60)^{1/a}[/tex]

where F[tex]_R[/tex] is the catalog rating( 2.12 kN)

L[tex]_R[/tex] is the rating life ( 3000 hours )

n[tex]_R[/tex] is the rating speed ( 500 rev/min )

F[tex]_D[/tex] is the desired load

L[tex]_D[/tex] is the desired life ( L₀ )

n[tex]_D[/tex]  is the the desired speed ( n₀ )

Now as we know, a = 3 for ball bearings

so we substitute

[tex]2.12( 3000 * 500 * 60 )^{1/3[/tex]  =  [tex]F_D( L_0n_060)^{1/3[/tex]    

950.0578 = [tex]F_D( L_0n_0)^{1/3} 3.914867[/tex]    

950.0578 / 3.914867 = [tex]F_D( L_0n_0)^{1/3}[/tex]

242.6794 =   [tex]F_D( L_0n_0)^{1/3}[/tex]

F[tex]_D[/tex] for A =  (242.6794 / [tex]( L_0n_0)^{1/3}[/tex] ) kN

Therefore the load that bearing A can carry is  (242.6794 / [tex]( L_0n_0)^{1/3}[/tex] ) kN

Next is Bearing B

[tex]F_R(L_Rn_R60)^{1/a}[/tex] = [tex]F_D(L_Dn_D60)^{1/a}[/tex]

F[tex]_R[/tex] = 7.5 kN, [tex](L_Rn_R60) = 10^6[/tex]

Also, for ball bearings, a = 3

so we substitute

[tex]7.5(10^6)^{1/3[/tex] = [tex]F_D(L_0n_060)^{1/3}[/tex]

750 =  [tex]F_D(L_0n_0)^{1/3} 3.914867[/tex]

750 / 3.914867  =  [tex]F_D(L_0n_0)^{1/3}[/tex]

191.5773 = [tex]F_D(L_0n_0)^{1/3}[/tex]

F[tex]_D[/tex] for B = ( 191.5773 / [tex](L_0n_0)^{1/3}[/tex] ) kN

Therefore, the load that bearing B can carry is  ( 191.5773 / [tex](L_0n_0)^{1/3}[/tex] ) kN

Now, comparing the Two results above,

we can say;

F[tex]_D[/tex] for A > F[tex]_D[/tex] for B

Hence, Bearing A can carry the larger load

Answer:

The temperature after a long time will return to 15°C

Explanation:

Determine the temperature of the slab after a very long time

First we calculate the heat flow for m^2 area normal to the surface

= q / A = 650°c - 15°C / ( 1 / h  + L / K )

           = 635°c  / ( 1 / 220 + 0.1 / 110 )  = 116.416 kw/m^2

Total heat content in the slab is calculated as

= m* c * ΔT

= 8530 * A * 0.1 * 380 * ( 650 - 15 )

= 205828.9  kJ/m^2

The temperature will return to 15°C after a long time

Answer:

Explanation:

Given that:

diameter = 100 mm

initial temperature = 500 ° C

Conventional coefficient = 500 W/m^2 K

length  = 1 m

We obtain the following data from the tables A-1;

For the stainless steel of the rod [tex]\overline T = 548 \ K[/tex]

[tex]\rho = 7900 \ kg/m^3[/tex]

[tex]K = 19.0 \ W/mk \\ \\ C_p = 545 \ J/kg.K[/tex]

[tex]\alpha = 4.40 \times 10^{-6} \ m^2/s \\ \\ B_i = \dfrac{h(\rho/4)}{K} \\ \\ =0.657[/tex]

Here, we can't apply the lumped capacitance method, since Bi > 0.1

[tex]\theta_o = \dfrac{T_o-T_{\infty}}{T_i -T_\infty}} \\ \\ \theta_o = \dfrac{50-30}{500 -30}} \\ \\ \theta_o = 0.0426\\[/tex]

[tex]0.0426 = c_1 \ exp (- E^2_1 F_o_)\\ \\ \\ 0.0426 = 1.1382 \ exp (-10.9287)^2 \ f_o \\ \\ = f_o = \dfrac{In(0.0374)}{0.863} \\ \\ f_o = 3.81[/tex]

[tex]t_f = \dfrac{f_o r^2}{\alpha} \\ \\ t_f = \dfrac{3.81 \times (0.05)^2}{4.40 \times 10^{-6}} \\ \\ t_f= 2162.5 \\ \\ t_f = 36 mins[/tex]

However, on a single rod, the energy extracted is:

[tex]\theta = pcv (T_i - T_{\infty} )(1 - \dfrac{2 \theta}{c} J_1 (\zeta) ) \\ \\ = 7900 \\times 546 \times 0.007854 \times (500 -300) (1 - \dfrac{2 \times 0.0426}{1.3643}) \\ \\ \theta = 1.54 \times 10^7 \ J[/tex]

Hence, for centerline temperature at 50 °C;

The surface temperature is:

[tex]T(r_o,t) = T_{\infty} +(T_1 -T_{\infty}) \theta_o \ J_o(\zeta_1) \\ \\ = 30 + (500-30) \times 0.0426 \times 0.5386 \\ \\ \mathbf{T(r_o,t) = 41.69 ^0 \ C}[/tex]

Answer:

Option B

Explanation:

Catalytic convertor with in the exhaust pipes of any vehicle converts harmful gases (such as hydrocarbons (HC), carbon monoxide (CO) and nitrogen oxides (NOx)) produced by combustion of fossil fuels (petrol, diesel etc.) into less harmful/toxic pollutants by acting as a catalyst for redox reaction. A catalytic convertor releases some mild gases from the exhaust like less harmful CO2, nitrogen and water vapour (steam)

Hence, option B is correct

Answer:

The issues related to the privacy are:

1. Informational privacy

2. Discrimination factors

3. Biased grouping on the basis of Data mining

4. Lack of consent

5. Morally wrong

6. Illegal distribution of information risks

7. Possibility of threat to life

Let's look at some major concerns:

1. Informational privacy : The concept of privacy of the personal information is totally nullified when the information is being used for a purpose other than the intended one for which it was given. This unethical use of information even for general purposes is not correct and is a matter of concern. It is more like using the sensitive data of others for personal benefit which is purely objectionable and raises security issues. Sometimes the data is also shared with the potential employers which might have certain impacts we are unaware of.

2. Data mining issues : The process of using a certain information to arrive and understand the trend and outcomes is called data mining. In this case, the consumer's data undergoes grouping and might get placed in the wrong group rather than the actual one. Also, there can be a case of biasing towards the groups which are not be focused on, or are not a part of the intended audience. This leads to the discrimination factors if we see it from a social point of view.

3. Lack of consent : Use of information without the consent or awareness of the consumers raises concern over the business ethics followed by the company. No one deserves the right to misuse information for his personal benefits without any of its information to the consumer. It is morally wrong and againt the work ethics. Moreover, it raises trust issues between the two involved, and hence is socially unacceptable.Explanation:

probably in it's chromosomes

Answer:

the highest rate of heat transfer allowed is 0.9306 kW

Explanation:

Given the data in the question;

Volume = 4L = 0.004 m³

V[tex]_f[/tex] = V[tex]_g[/tex] = 0.002 m³

Using Table ( saturated water - pressure table);

at pressure p = 175 kPa;

v[tex]_f[/tex] = 0.001057 m³/kg

v[tex]_g[/tex] = 1.0037 m³/kg

u[tex]_f[/tex] = 486.82 kJ/kg

u[tex]_g[/tex] 2524.5 kJ/kg

h[tex]_g[/tex] = 2700.2 kJ/kg

So the initial mass of the water;

m₁ = V[tex]_f[/tex]/v[tex]_f[/tex] + V[tex]_g[/tex]/v[tex]_g[/tex]

we substitute

m₁ = 0.002/0.001057  + 0.002/1.0037

m₁ = 1.89414 kg

Now, the final mass will be;

m₂ = V/v[tex]_g[/tex]

m₂ = 0.004 / 1.0037

m₂ = 0.003985 kg

Now, mass leaving the pressure cooker is;

m[tex]_{out[/tex] = m₁ - m₂

m[tex]_{out[/tex] = 1.89414  - 0.003985

m[tex]_{out[/tex] = 1.890155 kg

so, Initial internal energy will be;

U₁ = m[tex]_f[/tex]u[tex]_f[/tex] + m[tex]_g[/tex]u[tex]_g[/tex]

U₁ = (V[tex]_f[/tex]/v[tex]_f[/tex])u[tex]_f[/tex]  + (V[tex]_g[/tex]/v[tex]_g[/tex])u[tex]_g[/tex]

we substitute

U₁ = (0.002/0.001057)(486.82)  + (0.002/1.0037)(2524.5)

U₁ = 921.135288 + 5.030387

U₁ = 926.165675 kJ

Now, using Energy balance;

E[tex]_{in[/tex] -  E[tex]_{out[/tex] = ΔE[tex]_{sys[/tex]

QΔt - m[tex]_{out[/tex]h[tex]_{out[/tex] = m₂u₂ - U₁

QΔt - m[tex]_{out[/tex]h[tex]_g[/tex] = m₂u[tex]_g[/tex] - U₁

given that time = 75 min = 75 × 60s = 4500 sec

so we substitute

Q(4500) - ( 1.890155 × 2700.2 ) = ( 0.003985 × 2524.5 ) - 926.165675

Q(4500) - 5103.7965 = 10.06013 - 926.165675

Q(4500) = 10.06013 - 926.165675 + 5103.7965

Q(4500) = 4187.690955

Q = 4187.690955 / 4500

Q = 0.9306 kW

Therefore, the highest rate of heat transfer allowed is 0.9306 kW

Answer: Cleaning of mechanical parts is necessary to remove contaminants, and to avoid clogging of wastes which could restrict the functioning of the machine.

Explanation:

There are different agents used for cleaning different machine instruments to prevent their corrosion and experience proper cleaning.

Backing plates must be dry cleaned using a cotton cloth to remove the dirt, dust or any other dry contaminant.

Struts can be wet cleaned by applying alcoholic solvent.

Levers can be cleaned using a mineral spirit.

Metallic plates can be cleaned using water based solution or water.