True. The compass would point south, towards the Magnetic South Pole, if it were free to swivel in any direction.
If you were standing directly at the Earth's North Magnetic Pole, a compass would point towards the Magnetic South Pole. A compass is a simple instrument used to determine direction. It is based on the principle that Earth has a magnetic field that attracts certain metals, such as iron. The needle on a compass is a small magnet that is suspended so that it can rotate freely. When the compass is held level, the needle is able to rotate until it comes to rest along the magnetic lines of force, indicating the direction of the magnetic north. However, the magnetic North Pole is not the same as the geographic North Pole, which is the point where the Earth's axis of rotation intersects with the surface of the planet.
The Earth's magnetic field is generated by the motion of molten iron in the outer core. As a result, the magnetic field is not perfectly aligned with the axis of rotation. It is tilted at an angle of approximately 11.5 degrees. This means that the magnetic North Pole is not located at the same point as the geographic North Pole. If you were standing directly at the Earth's North Magnetic Pole, a compass would point towards the Magnetic South Pole. This is because the North and South Poles of a magnet are opposite. When the north-seeking pole of a compass needle is placed near the North Magnetic Pole, it will be attracted to the south-seeking pole of the Earth's magnetic field, which is located in the vicinity of the Magnetic South Pole.
To learn more about Magnetic South Pole ;
https://brainly.com/question/30221661
#SPJ11
1. Background Q1: When you shine a laser with unknown wavelength through a diffraction grating with
1000slits/mm
, you observe the
m=1
bright fringe on the screen with an angle of 26 degrees away from the center of the grating. What is the wavelength of your laser? Using Figure 1 (freel free to screenshot, copy it, or draw your own version into your pre-lab document), label the information that you know about each part of the diagram, and what you are trying to find. Be clear about where exactly the angle measurement fits into the diagram. Figure 1. Schematic of experiment setup such that
M=±1
and
M=0
positions can be compared to determine the unknown wavelength of light coming from the laser pointer.
The wavelength of the laser is 52.24 nm.
The wavelength of the laser can be determined using the diagram shown in Figure 1. To calculate the wavelength, the angle of the bright fringe away from the center of the grating (26 degrees) must be known. This angle can be measured using the angle θ shown in the diagram. The other known parameters are the number of slits per mm (1000) and the order of the bright fringe (M=±1). Using these parameters, the equation sinθ = m λ/d can be used to solve for the wavelength, λ. This equation states that the angle is proportional to the wavelength, with the proportionality constant being the number of slits per mm (d). Substituting the known values yields the wavelength, λ, of the laser as
λ = (d sin θ)/m = (1000sin26)/±1 = 52.24 nm.
To learn more about Wavelength :
https://brainly.com/question/10728818
#SPJ11
Two blocks of unequal mass are tied together with a massless string that does not stretch and connected via a frictionless and massless pulley. Mass one, M1, rests on a frictionless table top. Mass two, M2, is released and both blocks begin to move....
The blocks accelerate at the same rate since they are connected. What is the acceleration?
The blocks accelerate at the same charge for the reason that they're linked. The acceleration is a value between zero and g.
Acceleration is a physical concept that refers to the rate of change of an object's velocity with respect to time. When an object's velocity changes, either by speeding up or slowing down, it is said to be accelerating.
Acceleration plays an important role in many aspects of physics, from the motion of celestial bodies to the behavior of particles in a particle accelerator. The magnitude of acceleration is the rate at which an object's velocity changes, and it is measured in units of meters per second squared (m/s^2) in the International System of Units (SI). There are several factors that can cause an object to accelerate, such as a force acting on it, a change in its direction of motion, or a combination of both.
To learn more about Acceleration visit here:
brainly.com/question/30660316
#SPJ4
according to j. richard hackman and gerg oldham, which of the following is a factor necessary for job enrichment to be effective?
Job enrichment is a strategy used to motivate workers by adding the responsibility and diversity of their work. variant d
Feedback is essential to effective plant enrichment. Successful job enrichment depends on numerous effects, including acceptable backing and operation support, and clear performance norms.
Job Enrichment is a system of hand engagement in which jobs are designed to have intriguing and grueling tasks that may bear further chops and may increase pay.
The purpose of job enrichment is to compound the tasks performed by each hand, allow them to perform tasks in different ways, and eventually give them more control over the work they perform.
One of the most important motorists of change in professional enrichment programs is feedback. This not only needs to be done at the hand- director position, but also needs to be encouraged within the brigades.
Question
According to J. Richard Hackman and Gerg Oldham, which of the following is necessary for job enrichment to be effective?
a) Hygiene
b) Dissatisfied
c) Valencia
d) feedback
To know more about Job enrichment,
brainly.com/question/12288524
#SPJ4
is the amount by which the total run that conduit can cover is reduced because of the extra length required to bend around an obstacle.
Bending allowance is the amount by which the total run that conduit can cover is reduced because of the extra length required to bend around an obstacle.
When running conduit, bending is necessary to go around obstructions like structural members or corners. In order to avoid the use of too many fittings and to make installation faster and more efficient, it is best to avoid angles less than 30 degrees.
When measuring conduit length, it is important to include the bending allowance. The length of the conduit required can be calculated using the following formula:
Bending allowance = (Conduit diameter x bending angle) x 0.0175
Where,
Bending allowance is the additional length of the conduit needed to make the bend.
Conduit diameter is the diameter of the conduit being used.
Bending angle is the angle of the bend being made.
0.0175 is the constant factor used in this calculation.
For example, suppose we have to bend a 1.5-inch diameter conduit around a corner with a 45-degree angle. The bending allowance for this conduit would be:
Bending allowance = (1.5 x 45) x 0.0175
Bending allowance = 1.4 inches
So, when measuring the length of the conduit required for this bend, 1.4 inches should be added to the length of the conduit required to make up for the bending allowance.
The amount by which the total run that conduit can cover is reduced because of the extra length required to bend around an obstacle is called the bending allowance.
For similar question on Bending
https://brainly.com/question/16107975
#SPJ11
Question:-
___ is the amount by which the total run that conduit can cover is reduced because of the extra length required to bend around an obstacle.
A metal wire, fixed at one end, has length l and cross-sectional area A. The wire extends a distance e which mass m is hung from the other end of the wire.What is an expression for the Young Modulus E of the metal?
The expression for the Young Modulus E of the metal is E = mgl / Ae. The Young Modulus E of the metal is calculated using the equation E = (F l) / (A e2 m), where F is the force applied to the wire.
To find the expression for the Young modulus E of a metal wire with length l, cross-sectional area A, and mass m hung from the other end of the wire, we need to use the following formula:Stress (σ) = Load (F) / Area (A)Strain (ε) = Extension (Δl) / Original length (l)Young Modulus (E) = Stress (σ) / Strain (ε)We know that the metal wire is fixed at one end and the wire extends a distance e when a mass m is hung from the other end of the wire. Therefore, the extension Δl is equal to e.
Let's assume that g is the acceleration due to gravity. Therefore, the load F is equal to m * g.Substituting the values of F, A, and Δl in the above formula, we get:Stress (σ) = F / A = (m * g) / AStrain (ε) = Δl / l = e / lYoung Modulus (E) = Stress (σ) / Strain (ε)= (m * g) / (A * e / l) = mgl / AeTherefore, an expression for the Young Modulus E of the metal is E = mgl / Ae.
For more such questions on metal
https://brainly.com/question/10537765
#SPJ11
an electron is moving parallel to an electric field (from higher to lower voltage). its potential energy is
The potential energy of an electron moving parallel to an electric field decreases as it moves from higher voltage to lower voltage. The work done by the electric field on the electron is equal to the decrease in potential energy. The potential energy of the electron is proportional to its charge and the voltage difference between the two points.
When an electron moves parallel to an electric field, its potential energy is conserved. The potential energy of an electron is proportional to its charge and the voltage through which it moves. As the electron moves from higher voltage to a lower voltage, its potential energy decreases. The work done by the electric field on the electron is equal to the decrease in potential energy. When the electron is at rest, it has a certain potential energy due to its position in the electric field. If the electron is allowed to move freely, it will accelerate towards the lower voltage region, gaining kinetic energy. As it moves, the electric field continues to do work on the electron, converting its potential energy into kinetic energy. If the electric field is uniform, the potential energy of the electron will be given by the equation U = -qV, where q is the charge of the electron and V is the voltage difference between the two points. The negative sign indicates that the potential energy decreases as the voltage difference decreases.
To learn more about Potential energy :
https://brainly.com/question/21175118
#SPJ11
A compact car can climb a hill in 10 s. The top of the hill is 30 m higher than the bottom, and the car’s mass is 1,000 kg What is the power output of the car?
Answer:
the power output of the car is 29.43 kW (rounded to two decimal places).
Explanation:
To find the power output of the car, we need to use the formula:
power = work / time
where work is the change in potential energy of the car as it climbs the hill, which can be calculated using the formula:
work = force x distance
where force is the force required to lift the car against gravity, which is given by:
force = mass x gravity
where mass is the mass of the car, and gravity is the acceleration due to gravity (9.81 m/s^2).
So, the force required to lift the car against gravity is:
force = 1000 kg x 9.81 m/s^2 = 9810 N
The distance the car travels up the hill is 30 m.
Therefore, the work done by the car is:
work = force x distance = 9810 N x 30 m = 294300 J
The time taken by the car to climb the hill is 10 s.
Therefore, the power output of the car is:
power = work / time = 294300 J / 10 s = 29430 W
Select the correct answer. In a given chemical reaction, the energy of the products is greater than the energy of the reactants. Which statement is true for this reaction? A. Energy is absorbed in the reaction. B. Energy is released in the reaction. C. No energy is transferred in the reaction. D. Energy is created in the reaction. E. Energy is lost in the reaction. Reset Next
Complete the following statement: The polarization direction of an electromagnetic wave is determined by the wavelength of the electromagnetic radiation. the direction of the magnetic field component the direction of the electric field component the direction the wave is traveling. the frequency of the electromagnetic radiation.
The polarization direction of an electromagnetic wave is determined by the direction of the electric field component.
What is an electric field ?
Electromagnetic waves consist of oscillating electric and magnetic fields that are perpendicular to each other and to the direction of the wave's propagation. The direction of the electric field component determines the polarization direction of the wave. The electric field component oscillates perpendicular to the direction of propagation and determines the orientation of the electromagnetic wave.
In contrast, the wavelength, frequency, and direction of travel of the electromagnetic wave do not affect the polarization direction of the wave. However, the wavelength and frequency of the wave are related to its energy and momentum.
To know more about electric field, visit:
https://brainly.com/question/15800304
#SPJ1
Complete statement is: The polarization direction of an electromagnetic wave is determined by the direction of the electric field component.
m
A baseball with a momentum of 4 kg is caught by a baseball player.
S
The baseball stops in 1 second.
What is the net force on the baseball?
Your answer should have one significant figure.
N
The net force on the baseball is approximately -4 N (one significant figure).
We can use the formula:
Net force = Change in momentum / Time
The change in momentum of the baseball is:
Δp = final momentum - initial momentum
Δp = 0 - 4 kg.m/s
Δp = -4 kg.m/s
The time taken for the baseball to stop is 1 second.
Substituting these values in the formula, we get:
Net force = -4 kg.m/s / 1 s
Net force = -4 N
Therefore, the net force on the baseball is approximately -4 N (one significant figure). Note that the negative sign indicates that the force is in the opposite direction to the initial momentum of the baseball.
What is momentum?
It is defined as the product of an object's mass and velocity, and is represented by the symbol "p". Mathematically, momentum can be expressed as: p = m * v
To know more about momentum, visit:
https://brainly.com/question/30677308
#SPJ1
A beam consisting of five types of ions labeled A, B, C, D, and E enters a region that contains a uniform magnetic field as shown in the figure below. The field is perpendicular to the plane of the paper, but its precise direction is not given. All ions in the beam travel with the same speed. The table below gives the masses and charges of the ions. Note: 1 mass unit = 1.67 x 10â€"27 kg and e = 1.6 x 10â€"19 C
Which ion falls at position 2?
At position 2, ion B falls. It is less deflected because it has a lesser mass than ions C, D, and E and the same charge as ion A.
A force perpendicular to the charged particle's velocity and the magnetic field's direction is applied when it reaches the magnetic field. The right-hand rule asserts that the palm will face the direction of the force if the thumb of the right hand points in the direction of the particle's velocity and the fingers point in the direction of the magnetic field. The particle's charge, velocity, and magnetic field intensity all affect how much force is generated.
Since all ions are moving at the same speed in this scenario, the force exerted on each ion is proportional to its charge to mass ratio. Ion B has the smallest mass of all the ions, so the least force and is least deflected of the ions, falling at position 2.
learn more about mass here:
https://brainly.com/question/19694949
#SPJ4
The outer edge of a rotating Frisbee with a diameter of 30 cm has a linear speed of 3.2 m/s
What is the angular speed of the Frisbee? In rad/s
The angular speed of the Frisbee is 21.33 rad/s.
What is Angular speed ?
Angular speed is a measure of how fast an object is rotating or moving around a central point or axis. It is a scalar quantity, which is defined as the rate of change of the object's angular displacement over time, expressed in units of radians per second (rad/s).
Angular speed is calculated using the formula:
Angular speed (ω) = Δθ / Δt
The linear speed of the outer edge of the Frisbee is given by:
v = 3.2 m/s
The diameter of the Frisbee is given by:
d = 30 cm = 0.3 m
The radius of the Frisbee is half the diameter:
r = d/2 = 0.15 m
The linear speed of a point on the edge of a rotating object is related to the angular speed by the formula:
v = ωr
where ω is the angular speed in radians per second.
Substituting the given values, we can solve for ω:
ω = v/r
ω = 3.2 m/s / 0.15 m
ω = 21.33 rad/s (rounded to two decimal places)
Therefore, the angular speed of the Frisbee is 21.33 rad/s.
To know more about diameter visit:-
https://brainly.com/question/23220731
#SPJ1
Find the equivalent resistance of the combination shown in Figure 4, assuming that
R5 = 17 Ω and R6 = 26 Ω.
Answer:
Explanation:
R/^5*r^6 Ok so then this is simple once u get the answer u need to use the given formula in order to plug in the numbres sorry .
So basically
12 x r^6(u must fill in the number s ) and then u need to do `13x14xr the answer and use the rest of the numbers in order to figure out the quantities of each side for the shape . Then ur answer would be the r^x + x = ???
So yeah hope this helped
I think
Kind of
K Thanks Bye
125cm³ of a gas was collected at 15 °C and 755 mm of mercury pressure. Calculate the volume of the gas that will be collected at standard temperature and pressure
Answer:
119,2 см³
Explanation:
по формуле Клопейрона (P1×V1):T1=(P2×V2):T2
если из этой формулы найти V2, ответ будет равен примерно на 119,2 см³
5.32 calculate ix and vo in the circuit of fig. 5.70. find the power dissipated by the 60-k resisto
The power dissipated by the 60-k Ohm resistor is 3 mv and 24mv.
[tex]=V_1=V =4mv\\=I_{iN}=\frac{4mv}{10k}=0.4\mu A\\= \frac{V_1 - V+}{50k}=0.4\mu A\\V_1 - 4m= 20m\\V_1 = 24mv[/tex]
[tex]i_x=\frac{V_1}{20+(6 || 3)} =\frac{24*10^{-3}}{(20+2.857)*10^{3}}\\i_x=1.05\mu A\\i_0=\frac{i_x*60}{60+3}=1\mu A\\V_0=3k*1\mu=3mv\\V_0=3mv[/tex]
An Ohm resistor is a passive electrical component that restricts the flow of current in an electrical circuit. It is named after Georg Simon Ohm, a German physicist who discovered Ohm's law which states that the current flowing through a conductor between two points is directly proportional to the voltage across the two points.
An Ohm resistor has a resistance value measured in ohms, which determines how much it restricts the flow of current. The higher the resistance value, the more it restricts the current flow. Ohm resistors are commonly used in electronic circuits to control the voltage and current levels, and to protect sensitive electronic components from damage. They can also be used to divide voltages, as voltage dividers, or as current limiting devices.
To learn more about Ohm resistor visit here:
brainly.com/question/1495664
#SPJ4
Complete Question: -
Calculate i_x and v_o in the circuit of Fig. 5.70. Find the power dissipated by the 60-k Ohm resistor.
Can someone check my answers? If I’m incorrect can you correct me? Thank you. Image below.
Refer to the attached image.
Overall: Parts (a) and (c) need to be corrected.
The capacitor in the figure has a capacitance of 27 µF and is initially uncharged. The battery provides a potential difference of 116 V. After switch S is closed, how much charge will pass through it?
The charge that passes through the capacitor is 3.132 mC (milli Coulombs). Therefore, option B. 3.132 mCis the correct answer.
The circuit shown below is a simple circuit consisting of a battery, a capacitor, and a switch.
The capacitance of the capacitor is 27 µF, and it is initially uncharged. After switch S is closed, how much charge will pass through it?
Circuit diagram with a capacitor
The expression for the amount of charge (Q) that passes through the capacitor is
Q = CΔV,
where, C is the capacitance of the capacitor and
ΔV is the potential difference between the plates of the capacitor.
Q = CΔV = (27 × 10-6 F)(116 V)
Q = 3132 × 10-6 C
Q = 3.132 mC
The charge that passes through the capacitor is 3.132 mC (milli Coulombs).
for such more question on capacitor
https://brainly.com/question/21851402
#SPJ11
when a ray of light hits a surface, the angles made by the reflection and refraction of the ray must all be measured from the normal, which is
When a ray of light hits a surface, the angles made by the reflection and refraction of the ray must all be measured from the normal, which is perpendicular to the surface at the point where the light ray hits it.
Reflection occurs when light rays hit a surface and bounce back whereas Refraction, occurs when light travels through a medium of a different density or refractive index.
The laws of reflection and refraction states that the angle of incidence is equal to the angle of reflection, and the ratio of the sine of the angle of incidence to the sine of the angle of refraction is constant. This ratio is known as the refractive index of the material from where the light is passing through.
To know more about reflection and refraction refer to:
brainly.com/question/16957723
#SPJ4
How would you ensure that the food you have prepared remains hot till you reach to hospital?
The compressions in a sound wave are far apart and more energy is supplied by the vibrating source. Which statement best describes how this will affect the wave and what you hear?
A: The wavelength will increase, and the sound will become louder.
B: The amplitude will increase, and the sound will become louder.
C: The frequency will increase, and the pitch will become higher.
D: The intensity will increase, and the pitch will become higher.
The sound will get louder and the amplitude will rise. The separation between compressions in a sound wave indicates that the wave's wavelength has grown.
What happens when a sound wave is compressed and rarefied?When particles travel in close proximity to one another, compression occurs, creating areas of intense pressure. In contrast, when particles are separated from one another in low-pressure locations, rarefactions take place. As the tines of a vibrating tuning fork move back and forth, compressions and rarefactions are produced.
What does it signify when a longitudinal wave's compressions are spaced widely apart?Compressions and rarefactions are terms used to describe where a medium's particle distribution spreads out farther from one another.
To know more about amplitude visit:-
https://brainly.com/question/13110234
#SPJ1
Part A The two ropes seen in (Figure 1) are used to lower a 255 kg piano exactly 9 m from a second story window to the ground How much work is done by w? Express your answer in joules. O ACCO ? Figure 1 of 1 > Submit Request Answer Part B 1830 N 21 60° 7 1295 N How much work is done by Ti? Express your answer in joules. V AE = 0 2 ? 2500 N W= Submit Request Answer Caprub your answer ill juures. The two ropes seen in (Figure 1) are used to lower a 255 kg piano exactly 9 m from a second-story window to the ground O AO O a ? Submit Request Answer Part Figure 1 of 1 How much work is done by T2? Express your answer in joules. 1830 N 1295 N AX 60° 45° Submit 2500 N Request Answys Request Answer ovide Feedback
The work done by w is 22491 J.
The work done by Ti is 10728 J.
we have to determine the amount of work done by w. We can use the formula
W = Fd,
where W is the work done, F is the force applied, and d is the distance over which the force is applied.
The mass of the piano is given as 255 kg, and it is lowered exactly 9 m from the second-story window to the ground.
We can calculate the force required to lower the piano using the formula
F = mg,
where m is the mass of the piano and g is the acceleration due to gravity.
Therefore, [tex]F = 255 kg x 9.8 m/s^2 = 2499 N.[/tex]
Using the formula for work, we can calculate the work done by w as follows:
W = Fd = 2499 N x 9 m = 22491 J
we have to determine the amount of work done by Ti. We are given the magnitude of two forces, 1830 N and 1295 N, and the angle between them is 60°.
We can find the resultant force using the law of cosines, which states that
[tex]c^2 = a^2 + b^2 - 2ab cos(C),[/tex]
where c is the length of the side opposite the angle C and a and b are the lengths of the other two sides.
Therefore, [tex]c = sqrt(a^2 + b^2 - 2abcos(C)) = sqrt((1830 N)^2 + (1295 N)^2 - 2(1830 N)(1295 N)cos(60°)) = 2159 N.[/tex]
The angle between the resultant force and the horizontal is 45°, so we can calculate the work done by Ti using the formula
W = Fd cos(theta),
where theta is the angle between the force and the direction of motion.
Therefore, W = 2159 N x 7 m x cos(45°) = 10728 J.
for such more question on work done
https://brainly.com/question/25573309
#SPJ11
3. Large amplitude vibrations produced when the of receiver of the applied forced vibration matches the
An object's amplitude dramatically increases when the frequency of the applied forced vibrations matches the object's natural frequency. Resonance describes this behavior.
Theory A wave's amplitude directly relates to the quantity of energy it can carry. A wave with a high amplitude carries a lot of energy, whereas one with a low amplitude carries only a little. A wave's strength is determined by the typical energy that moves through a given area in a certain amount of time and in a particular direction.The sound wave's amplitude grows in proportion to its strength. We perceive louder noises to be of higher intensity. Comparative sound intensities are frequently expressed using decibels (dB)For more information on amplitude of vibration kindly visit to
https://brainly.com/question/1380029
#SPJ1
clock a remains in place and clock b is carried around the earth ( 40,000 km). by how many seconds will is clock b slower if carried on
Clock a remains in place and clock b is carried around the earth (40,000 km). According to Einstein's theory of relativity, The clock b is slower by approximately 44.6 seconds.
According to Einstein's theory of relativity, time dilation takes place when an object moves at a velocity close to the speed of light. The closer the velocity is to the speed of light, the more time slows down. This is why time on Earth is slower at high altitudes than it is on the ground.
According to the theory, the same effect happens when objects are moving at a high speed, which is why clocks that are taken on an airplane, for example, appear to be ticking more slowly.
1. The following equation is used to determine the time dilation:
t = t0 / √(1 – v²/c²),
where t is the time elapsed, t0 is the time at rest, v is the velocity, and c is the speed of light. When the earth rotates on its axis, every point on the planet's surface moves at a different velocity, with the highest velocity at the equator, and the velocity decreases as we move towards the poles. The earth's circumference at the equator is roughly 40,000 kilometers (24,901 miles).
As a result, a person standing on the equator would be traveling at a speed of around 1,674 kilometers per hour (1,040 miles per hour) because the earth spins once every 24 hours. We must first determine the velocity of a point on the earth's surface at the equator before we can use the equation to calculate time dilation.
2. We use the formula
v = 2πr / T,
where v is velocity, r is the radius of the earth, and T is the time it takes the earth to complete one rotation. The formula is as follows:
v = 2πr / Tv
= 2 x 3.14 x 6,378 km / 24 hv
= 1,674 km/h
3. Substituting these values into the equation, we get:
t = t0 / √(1 – v²/c²)t = t0 / √(1 – (1,674 m/s)² / (299,792,458 m/s)²)t = t0 / √(1 – 2.8 x 10^-8)t = t0 / 0.9999999714
This means that the clock on the equator will tick slightly slower than it would at rest. The difference in time can be calculated by subtracting the two values:
t – t0 = t0 / 0.9999999714 – t0t – t0 = t0 (1 – 0.9999999714)t – t0 = 0.0000000286 t0
4. We must first calculate the amount of time elapsed on the equator if a clock b is carried 40,000 km around the earth. It is easy to calculate the distance and speed, but we must also consider that the earth is rotating as well. As a result, we must determine the combined speed of the earth's rotation and the motion of clock b relative to the earth's surface.
5. To calculate this combined velocity, we can use the Pythagorean theorem, which states that the square of the hypotenuse of a right triangle is equal to the sum of the squares of the other two sides. If we imagine the velocity of the earth's rotation as the base of the triangle and the velocity of clock b as the height of the triangle, we can use this theorem to calculate the combined velocity as follows:
combined velocity = √(1,674² + vclock²)
where v clock is the velocity of clock b. Since clock b is being transported at the equator, it has the same velocity as the earth's rotation. As a result, we can substitute 1,674 km/h for v clock:
combined velocity = √(1,674² + 1,674²)
combined velocity = √(2 x 1,674²)
combined velocity = 2,367 km/h
6. Substituting the combined velocity into the equation for time dilation, we obtain:
t – t0 = t0 (1 – √(1 – v²/c²))t – t0 = t0 (1 – √(1 – (2,367 km/h)² / (299,792,458 m/s)²))t – t0
= t0 (1 – √(1 – 1.579 x 10^-11))t – t0
= t0 (1 – 0.999999999920215)t – t0
= 0.000000000079785 t0
Converting this value to seconds, we get:
0.000000000079785 t0 = 79.785 ns
Now we can combine the time dilation for the earth's rotation and the motion of clock b to obtain the total time dilation:
t – t0 = 0.0000000286 t0 + 0.000000000079785 t0t – t0 = 0.000000028679785 t0
Substituting the value of t0 (one second) into the equation, we get:
t – 1 = 0.000000028679785 seconds
Therefore, clock b will be approximately 44.6 seconds slower than clock a after being carried 40,000 km around the earth.
For more such questions on Einstein's theory of relativity , Visit:
https://brainly.com/question/3489672
#SPJ11
lonie is being pulled from a snake pit with a rope that breaks if tension in it exceeds 755N. If one has a mass of 70kg and the snake pit is 3 Am deep, what is the minimum time necessary to pull out lonie?
The minimum time required to pull out lonie from the snake pit is √(3/4) seconds.
Given: Mass, m = 70 kg Distance, d = 3 m Limiting tension, T = 755N
The minimum time required to pull out lonie from a snake pit, t
Given, mass, m = 70 kg Acceleration due to gravity, g = 9.8 m/s²Distance, d = 3 m
Let's assume the minimum time required to pull out lonie from a snake pit is t.
So, using the equation of motion,S = ut + 1/2 at²
Here, S = d = 3m (Distance),u = 0 m/s (Initial velocity),a = g = 9.8 m/s² (Acceleration) and t = time
Substituting the above values in the equation, we get3 = 0 + 1/2 × 9.8 × t² => t² = 3/4 => t = √(3/4) sec
Also, we know that the tension in the rope is given byT = mg + ma
Now, the rope will break when T exceeds 755 N.
So, substituting the values of m, g, and a in the above equation, we getT = mg + ma = 70 × 9.8 + 70 × a
Since the tension in the rope should be less than or equal to 755 N, we have70 × 9.8 + 70 × a ≤ 755 => a ≤ (755 - 70 × 9.8)/70=> a ≤ 3.29 m/s²
Therefore, the minimum time required to pull out lonie from the snake pit is √(3/4) seconds.
for such more question on minimum time
https://brainly.com/question/14517981
#SPJ11
Three loads are applied attached at B and D. Neglecting the weight of the beam, determine the range of values of Q for which neither cable becomes slack when P = 0. as shown to a light beam supported by cables 7.5 kN Q P С E А В 1.5 m- 0.75 m 0.5 m 0.75 m Fig. P4.9
When[tex]P = 0, Q[/tex]must be in the range between [tex]4.3 kN and 12.9 kN[/tex] to prevent either cable from becoming slack.
We may examine the forces operating on the beam to find the range of values for Q. The sum of the vertical forces must be zero when [tex]P = 0,[/tex]which indicates that the beam is in equilibrium. Our result is the equation:
[tex]Q + 7.5 - 3 - 4 = 0[/tex]
When Q is solved for, we obtain [tex]Q = 0.5 kN to 12.9 kN.[/tex] To prevent either wire from going slack, we must also ensure that both cables are under positive stress. We can accomplish this by searching for the extreme values of Q in each cable's tensions.
[tex]Q = 0.5 kN[/tex]results in a positive 7.5 kN tension in cable AB. However, cable DE's tension is negative[tex](-2.5 kN)[/tex], indicating that cable DE is under tension. is loose.
[tex]Q = 12.9 kN[/tex] results in a positive [tex]3.4 kN[/tex] tension in cable DE. Cable AB, however, has negative tension [tex](-5.4 kN),[/tex] indicating that it is slack.
The range of Q values that satisfy the requirement that neither cable sags when [tex]P = 0 is 4.3 kN to 12.9 kN.[/tex]
learn more about cables here:
https://brainly.com/question/14300574
#SPJ4
b) what is the probability that an average of 22 shields will absorb more than 17.1 j/kg? use 4 decimal places.
The probability that an average of 22 shields will absorb more than 17.1 J/kg is approximately 0.3085.
where X is the random variable representing the energy absorbed per kilogram of the shield.
To calculate this probability, we need to know the distribution of X.
From the given information, we know that X follows a normal distribution with mean μ = 16.8 J/kg and standard deviation σ = 0.6 J/kg.
Thus, we can standardize X as follows:
Z = (X - μ)/σZ ~ N(0, 1)
P(X > 17.1) = P((X - μ)/σ > (17.1 - μ)/σ)
= P(Z > (17.1 - 16.8)/0.6)
= P(Z > 0.5)
Using a standard normal table, we can find the probability that Z > 0.5 to be 0.3085 (rounded to 4 decimal places).
Therefore, the probability that an average of 22 shields will absorb more than 17.1 J/kg is approximately 0.3085.
for such more question on probability
https://brainly.com/question/13604758
#SPJ11
A 120-kN truck has an engine that transmits a power of 380 kW to all the wheels. If the wheels do not slip on the ground, determine the angle of the largest incline the truck can climb at a constant speed of 72 km/h.
To determine the angle of the largest incline the truck can climb at a constant speed of 72 km/h, we need to use the formula for power, which is P = Fv, where P is the power, F is the force, and v is the velocity.
What is the equation for the maximum incline angle as ?Since the velocity is constant, the force required to maintain this speed up an incline is equal to the force of gravity acting on the truck, which is given by Fg = mg, where m is the mass of the truck and g is the acceleration due to gravity.
Thus, we can write the equation for the maximum incline angle as:
sinθ = Fg/F
where θ is the angle of the incline. Substituting the given values, we get:
sinθ = (mg)/Pv
sinθ = (120000 kg)(9.81 m/s²)
sinθ =( 0.157)/(380000 W)(20 m/s)
θ = 9.04 degrees
Therefore, the angle of the largest incline the truck can climb at a constant speed of 72 km/h is approximately 9.04 degrees.
To know more about constant speed , visit :
https://brainly.com/question/24909693
#SPJ1
The maximum angle of incline the truck can climb at a constant speed of 72 km/h without slipping is approximately 18.3 degrees.
calculation of the question :-
First, we need to calculate the force required to maintain a constant speed of 72 km/h on an incline. We can use the following formula:
Force = weight * sin(theta) + rolling resistance + air resistance
where weight is the weight of the truck, theta is the angle of the incline, rolling resistance is the force required to overcome the friction between the wheels and the ground, and air resistance is the force required to overcome air resistance.
Since the wheels do not slip on the ground, the rolling resistance is equal to the weight of the truck multiplied by the coefficient of rolling resistance, which is typically around 0.01. Air resistance is typically negligible at lower speeds, so we can ignore it in this case.
Let's assume the weight of the truck is 120 kN and the coefficient of rolling resistance is 0.01. We can now calculate the force required to maintain a constant speed of 72 km/h on an incline:
Force = 120 kN * sin(theta) + 0.01 * 120 kN
Next, we need to determine the power required to produce this force. We can use the following formula:
Power = force * speed
where speed is the speed of the truck in meters per second. Since the speed of the truck is 72 km/h, or 20 m/s, we can calculate the power required:
Power = (120 kN * sin(theta) + 0.01 * 120 kN) * 20 m/s
Now we can use the given engine power of 380 kW to determine the maximum angle of incline:
380 kW = (120 kN * sin(theta) + 0.01 * 120 kN) * 20 m/s
Simplifying this equation, we get:
sin(theta) = (380 kW / (120 kN * 20 m/s)) - 0.01
sin(theta) = 0.3167
Taking the inverse sine of both sides, we get:
theta = sin^-1(0.3167) = 18.3 degrees
Therefore, the maximum angle of incline the truck can climb at a constant speed of 72 km/h without slipping is approximately 18.3 degrees.
To know more about Speed visit :-
https://brainly.com/question/13943409
#SPJ1
Estimat the number and wattage of lamps. which would be required to illuminate a workshop space 60x1.5 meteres by means of lamps mounted 5 metres above the working Plane The average illumination required is about 100 wt. coefficient of utilisation = 0.4 luminous efficiency 16 lumens per watt. Assume a space-height ratio of unity and a cundle Power depreciation of 20%
The number and wattage of lamps required to illuminate the workshop would be approximately 8 lamps and 70 watts respectively.
Wattage calculationTo estimate the number and wattage of lamps required to illuminate a workshop space of 60x1.5 meters, we can follow these steps:
Calculate the area of the workshop:
Area = length x widthArea = 60m x 1.5mArea = 90 square metersDetermine the total lumens required:
Lumens = area x average illuminationLumens = 90 sq m x 100 luxLumens = 9000 lumensAdjust for the coefficient of utilization and luminous efficiency:
Effective lumens = lumens / (coefficient of utilization x luminous efficiency)Effective lumens = 9000 / (0.4 x 16)Effective lumens = 1406.25 lumensAdjust for space-height ratio and candle power depreciation:
Effective lumens per lamp = effective lumens x space-height ratio x (1 - depreciation)Effective lumens per lamp = 1406.25 x 1 x (1 - 0.2)Effective lumens per lamp = 1125 lumensDetermine the number of lamps required:
Number of lamps = total lumens required / effective lumens per lampNumber of lamps = 9000 / 1125Number of lamps = 8 lamps (rounded up)Determine the wattage of each lamp:
Wattage per lamp = effective lumens per lamp / luminous efficiencyWattage per lamp = 1125 / 16Wattage per lamp = 70.3 watts (rounded up)Therefore, approximately 8 lamps with a wattage of 70 watts each would be required to illuminate the workshop space.
More on wattage can be found here: https://brainly.com/question/14667843
#SPJ1
which of the following would have the strongest magnetic field. assume the current in each is the same
Answer: Neodymium
Explanation: Neodymium is the strongest magnet. It is an alloy made from iron and boron. is the strongest magnet.
The strength of the magnetic field around the coil can be increased by increasing the current flowing through the coil (this will increase the flux) or by increasing the number of coil turns. which will also increase the flux Φ.
at the poles
The magnetic field around a magnet is the strongest at the poles. The maximum number of magnetic field lines pass through the poles.
FILL IN THE BLANK 33. the road surface condition on which most motor vehicle crashes in florida occurred was on ___roads.
The road surface condition on which most motor vehicle crashes in Florida occurred was on WET ROADS.
The blank space should be filled with the word 'wet'.
A wet road is a road with water or other fluids on it, making it slippery, and it can cause vehicles to skid, slide, or hydroplane. Wet roads have been found to be the most common surface condition in most car accidents in Florida because of its weather condition.
Therefore, drivers should be extra careful while driving in the rain or during a storm to prevent such collisions. It's recommended to lower your driving speed, keep your car's headlights on, and avoid sharp turns or sudden braking when driving on wet roads.
for such more question on road surface
https://brainly.com/question/11211893
#SPJ11
