Two mass m1 and m2 lie on a frictionless surface. Between the two masses is a compressed spring, with spring constant k. The system is held in place. At time t=0 the blocks are released. The blocks move off in opposite directions with velocities v1 and v2. how much was the spring compressed?

Answers

Answer 1

Answer:

The spring was compressed the following amount:

[tex]\Delta x=\sqrt{ \frac{m_1\,v_1^2+ m_2\,v_2^2}{k} }[/tex]

Explanation:

Use conservation of energy between initial and final state, considering that the surface id frictionless, and there is no loss in thermal energy due to friction. the total initial energy is the potential energy of the compressed spring (by an amount [tex]\Delta x[/tex]), and the total final energy is the addition of the kinetic energies of both masses:

[tex]E_i=\frac{1}{2} k\,(\Delta x)^2\\\\E_f=\frac{1}{2} m_1\,v_1^2+\frac{1}{2} m_2\,v_2^2[/tex]

[tex]E_i=E_f\\[/tex]

[tex]\frac{1}{2} k\,(\Delta x)^2=\frac{1}{2} m_1\,v_1^2+\frac{1}{2} m_2\,v_2^2\\k\,(\Delta x)^2=m_1\,v_1^2+ m_2\,v_2^2\\(\Delta x)^2=\frac{m_1\,v_1^2+ m_2\,v_2^2}{k} \\\Delta x=\sqrt{ \frac{m_1\,v_1^2+ m_2\,v_2^2}{k} }[/tex]


Related Questions

What would happen to the
to the output force (F2)if the area
of the piston1 is made larger than that of piston2? plz help ​

Answers

Answer:

The output force would decrease since exerted force is inversely proportional to contact area.

Explanation:

F ∝ [tex]\frac{1}{A}[/tex] , Where 'F' is the exerted force and 'A' is the contact area.

what is the frequency and wavelength of a remote control? PLEASE HURRY

Answers

Answer:

940 nanometers wavelength, and about an 300 mHz - 400 gHz frequency

2. Adelia holds a shiny steel spoon with its back (convex surface) facing her eyes at a distance
of approximately 30 cm. She sees an upright image of herself. However, when the spoon
is changed so that the front (concave surface) of the spoon is facing her eyes, an inverted
image is observed.
(a) Explain this situation.
(b) Why is an upright image not seen on the front surface of the spoon at that distance?​

Answers

Answer:

(a) The convex mirror image, is always upright at all positions, while images formed by concave mirrors are always inverted when the object distance from the mirror is more than the mirrors focal length.

(b) An upright image is not seen for object at a distance from a concave mirror further than the focal length of the mirror, which is the spoon in the question

Therefore, the location of her eyes of approximately, 30 cm,  from the mirror is more than the mirror's focal length

Explanation:

placement.
A body is thrown vertically upwards. Its velocity keeps on decreasing. What happens
to its kinetic energy when its reaches the maximum height? Why?
If the speed of a body is increased four times, how will its kinetic energy be affected?​

Answers

Answer:

kinetic energy will be equal to 0

Explanation:

this is because at final position velocity of body will become zero.

kinetic energy eill be 8 times

What is the equation for burning a fossil fuel

Answers

Answer:

Fuel + O2 → CO2 + H2O

Explanation:

A ship sets out to sail to a point 123 km due north. An unexpected storm blows the ship to a point 112 km due east of its starting point. (a) How far and (b) in what direction (as an angle from due east, where north of east is a positive angle) must it now sail to reach its original destination

Answers

Answer:

Explanation:

We shall represent the point of destination and point of new starting point in vector form .

i and j will represent east and north .

point of destination = 123 j

starting point = 112 i

distance between the two

D = 123 j - 112 i

magnitude of D = √ ( 123² + 112² )

= 166.35 km

Direction of D

Tanθ = -  123 / 112

= - 1.09

θ = 132.54 degree from east in positive angle .

For each of the following statements about deep-water waves, determine if the statement is true or false, then explain why: The longer the wave, the deeper the wave base. The greater the wave height, the deeper the wave base. The longer the wave, the faster the wave travels. The greater the wave height, the faster the wave travels. The faster the wave, the greater the wave height.

Answers

Answer:

The longer the wave, the deeper the wave base - True

The greater the wave height, the deeper the wave base - false

The longer the wave, the faster the wave travels- true

The greater the wave height, the faster the wave travels- false

The faster the wave, the greater the wave height - False

Explanation:

When a wave has a high length it means that the wave base will be deeper.

The longer the wave, the deeper the wave base - True

When the weight height is big , the wave base will be deeper.

The greater the wave height, the deeper the wave base - false

The longer the wave, the faster the wave travels- true

The greater the wave height, the faster the wave travels- false

The faster the wave, the greater the wave height - False

Which statement describes one feature of Rutherford's model of the atom?
O The atom is mostly empty space.
O The atom cannot be divided into smaller particles.
O Electron clouds are regions where electrons are likely to be found.
O The electrons are located within the positive material of the nucleus.

Answers

Answer:

The atom is mostly empty space.

Explanation:

Ernest Rutherford in the year 1911 developed a model of an atom. In his model the atom was shown that the atom is mostly empty spaces composed of negative electrons which orbits round a positive nucleus just like planets revolving round the sun.

Rutherford came up with this model by performing experiments in 1909 which involves the scattering of alpha particles on a thin gold foil. From this experiments he came up with his model.

Answer:

A!

Explanation:

The atom is mostly empty space.

Astronomers can now report that active star formation was going on at a time when the universe was only 20% as old as it is today. When astronomers make such a statement, how can they know what was happening inside galaxies way back then

Answers

Answer:

First, as you may know, the light travels at a given velocity.

In vaccum, this velocity is c = 3x10^8 m/s.

And we know that:

distance = velocity*time

Now, if some object (like a star ) is really far away, the light that comes from that star may take years to reach the Earth.

This means that the images that the astronomers see today, actually happened years and years ago (So the night sky is like a picture of the "past" of the universe)

Also, for example, if an astronomer sees some particular thing, he can apply a model (a "simplification" of some phenomena that is used to simplify it an explain it) and with the model, the scientist can infer the information of the given thing some time before it was seen.

The astronomers could know what was happening inside galaxies way back then by the fact that;

they examine the spectra of galaxies (or the overall colors of galaxies) with the highest redshifts they can find

Astronomers Measure the wavelength of the light that is stretched, so the light is seen as 'shifted' towards the red part of the spectrum by using spectroscopy. This measure is also called redshift.

This invokes a ray of light through a triangular prism that splits the light into various components known as spectrum.

The way the astronomers could use this concept to know what was happening in the galaxies before is by examining the spectra of galaxies that have the highest redshifts.

Read more at; https://brainly.com/question/15995216

1. A student gathered two boxes of the same size made of different materials: glass and clear plastic. She placed them on a windowsill in the sun for an hour and then measured the temperature of the air in each box. Which statement best describes the purpose of the experiment? to relate the type of box material to the temperature of the air within the box to relate the size of the box to the temperature of the air within the box to relate the type of box material to the mass of the box to relate the amount of time a box is exposed to sunlight to the temperature of the air within the box 2. What is the average time for the toy car to move 1.0 m on dirt? 20.2 s 24.4 s 28.1 s 60.7 s 3. A student collected data about the distance a ball falls over time. Which type of graph should he use to represent the data? circle graph scatterplot histogram bar graph

Answers

Answer:

1.  to relate the type of box material to the temperature of the air within the box

2. Question is incomplete

3. scatterplot

Explanation:

1. The only thing done differently in this experiment is the type of material used in making the boxes, hence the experiment must be about that. Before proceeding to answering this question, we must have this at the back of our minds.

We can gather from the experiment that the boxes are of the same size and were subjected to sunlight for an hour (the same time duration for both). Hence, the temperature of the air inside the box will only be affected by the type of material the box is made of since the boxes have the same size and were subjected to sunlight for the same duration.

From the options provided, the best description for this experiment is; to relate the type of box material to the temperature of the air within the box.

2. The question is incomplete. The value for speed/velocity needed to calculate the average time is missing.

However, the formula needed here is velocity = distance ÷ time

3. There are two variables in this experiment; distance and time

The type of graph that shows two variables on it (of the options provided) is the scatterplot.

Determine whether each sum, difference, product,
or quotient represents a rational number or an
irrational number. Explain how you know without
simplifying​

Answers

Explanation:

The asked in the Question is missing, although i am assuming the number

as [tex]\frac{6}{23}[/tex] ÷[tex]\frac{\sqrt{2} }{2}[/tex].

The given expression contains an irrational number. So, the quotient will also be an irrational number.

Solving

[tex]\frac{6}{23}\times\frac{\sqrt{2} }{2} \\=\frac{3\sqrt{2} }{23}[/tex]

Which is an irrational number.

A car is traveling to the right with a speed of 2.0\,\dfrac{\text m}{\text s}2.0 s m ​ 2, point, 0, start fraction, start text, m, end text, divided by, start text, s, end text, end fraction on an icy road when the brakes are applied. The car slows down with constant acceleration for 3.0\,\text m3.0m3, point, 0, start text, m, end text until it comes to a stop. How long does it take the car to slide to a stop?

Answers

Answer:

It took the car 3 second to come to full stop

Explanation:

When the car is driving to the right at a speed of 2 m/s, and suddenly brakes giving the car a constant negative acceleration making it travel 3 meters after it stops, we can use the following kinematic equation to solve for the acceleration applied by the brakes:

[tex]v=v_0-a\,t\\0=2-a\,t\\a=\frac{2}{t}[/tex]

and we use this result in the following kinematic equation for the distance traveled to find the time it took it to stop:

[tex]x-x_0=v_0\,t-\frac{1}{2} a\,\,t^2\\3=2\,t -\frac{1}{2} (\frac{2}{t}) \,\,t^2\\3=2\,t-t\\3=t[/tex]

therefore, it took the car 3 seconds to come to a full stop.

Halley is standing outside on a cloudy day. When she hears thunder, she goes back inside so that she doesn't get caught in
a storm. Is this an example of inference or prediction? Explain

Answers

Answer:

Inference

Explanation:

An inference involves the application of logic to progress from a premise to a conclusion or logical consequence on the basis of the evidence or known fact. Inference is a process of thought that be divided into a deduction and an induction aspect.

In the given question Halley, by standing outside was able to deduce the sound of thunder she is then able by inductive reasoning from the fact that storms are usually preceded by and accompany lightening, conclude that there is a storm coming.

A concave mirror has a radius of curvature of 80cm. If the real image of an object is formed at 1m, how far from the mirror is the object?

Answers

Answer:

66.7 cm

Explanation:

The focal length is half the radius of curvature, or f = 40 cm.

The image is real, so i = +100 cm.

The distance to the object is therefore:

1/o + 1/f = 1/i

1/o + 1/40 = 1/100

o = -66.7 cm

The object is 66.7 cm left of the mirror.

Match the following:
Tailored software
. Utility software
Operating system
Software
Packaged software
Set of programs
Library management system
Scan viruses
Microsoft Office
used to coordinate the hardw
the computer​

Answers

Answer:

1) Tailored software  Library management system

2) Utility software Scan viruses

3) Operating system Used to coordinate the hardware of the computer

4) Packaged software set of programs Microsoft office

Explanation:

1) A tailored software, also known as a custom software, is one that is designed and tailor-made only for a particular organisation

2) A utility software is a computer maintenance and analysis software used to enable proper functioning of the computer by performing restorative and maintenance tasks

3) Operating system software

The operating system software controls the operation of the computer hardware within the system and enables the operation of other programs in the computer

4) Packaged software are a collection of programs that are oriented to perform interrelated tasks that a focused to a particular area, such as Microsoft Office.

1. The first stage of stellar formation is the assembly (or formation) of a_______ . 2. Stars form in clouds. 3. When a cloud collapses it into smaller and smaller pieces till those pieces reach stellar masses. 4. As the density increases, the fragments become_______ , which________ the temperature of the cloud and inhibits further fragmentation. 5. The _______then condense into rotating globs of gas that serve as stellar embryos. 6. During this stage the surface temperature_______ and luminosity_________ despite decreasing size. 7. The central temperature and pressure increase as the potential energy is converted to energy due to contraction.

Answers

Answer: The keywords to input into the blank spaces were omitted which are ; fragments, increases, decreases, opaque, raises, molecular, protostar, gravitational, thermal.

Please find the answers for the blank spaces in the explanation column

Explanation:

1. The first stage of stellar formation is the assembly (or formation) of a_PROTOSTAR______ . 2. Stars form in MOLECULAR clouds. 3. When a cloud collapses, it FRAGMENTS into smaller and smaller pieces till those pieces reach stellar masses. 4. As the density increases, the fragments become_OPAQUE______ , which___RAISES_____ the temperature of the cloud and inhibits further fragmentation. 5. The __FRAGMENTS_____then condense into rotating globs of gas that serve as stellar embryos. 6. During this stage the surface temperature INCREASES_______ and luminosity__INCREASES_______ despite decreasing size. 7. The central temperature and pressure increase as the GRAVITATIONAL potential energy is converted to energy due to THERMAL contraction.

The above describes the evolution or formation of stars which begins with the collapse of a molecular cloud by gravitational force, this collapse cause the molecular cloud to fragment with the release of heat --Gravitation potential energy causing an increased temperature and pressure of the newly condensing  fragment with increasing luminosity known as a Protostar.

A space rocket accelerates uniformly from rest to 160ms^-1 upwards in 4.0s, then travels with a constant speed of 160ms^-1 for the next 5.0s.
What is the initial acceleration of the rocket?

Answers

Answer:

40 ms¯².

Explanation:

To solve this problem, we shall illustrate the question with a diagram.

The attached photo gives a better understanding of the question.

From the attached photo:

Velocity (v) = 160 ms¯¹

Time (t) = 4 secs.

Acceleration (a) =?

Acceleration (a) = Velocity (v) /time (t)

a = v/t

a = 160/4

a = 40 ms¯²

Therefore, the initial acceleration of the rocket is 40 ms¯².

The ways to measure the mass and volume of irregular object​

Answers

Answer:

When we have irregular objects, it may become very hard to calculate the volume of the object, as we actually can not use any simple equation to find it.

The mass is less tricky, just find a scale and wheight it, now we know the mass of the irregular object.

One way to measure the volume of the object is using water... how we do it?

Get some recipient with water, measure the height of the water.

Introduce your object into the water and totally submerge it, now the level of the water will rise. This is because as you introduce the object under the water, you are displacing up a given volume of water that has the same volume as the irregular object.

Now that you know the height of the water before and after you put your object, you can easily calculate the volume of water displaced, and that will be the volume of the object (the tricky part may be totally submerging the object if, for example, is wood and it floats, here you can use a thin wire to push it down but it will affect a little bit the measures.)

A capacitor C is fully charged by connecting it to battery of V Volt. Then it is disconnected from battery. If the separation between the plates is halved, what will happen to (i) Charged stored by capacitor (ii) Potential difference across it. (iii) Electric filed strength between the plates. (iv) Energy stored by the capacitor.

Answers

Answer:

Explanation:

i )

When it is disconnected with the battery , the charge stored in it becomes fixed . When the plate distance becomes half , its capacitance becomes twice from C to 2C . Let charge stored in it at the time of disconnection from battery be Q . Let plate separation reduces from d to d / 2

So charged stored in it will remain unchanged .

ii )

Potential difference = charge / capacitance

in the first case potential difference = Q / C

in the second case potential difference = Q / 2C

So potential difference becomes half .

iii ) electric field = potential diff / plate separation

in the first case electric field = Q / (d x C )

in the second case electric field = 2 Q / (d x 2C)

= Q / (d  x C )

So electric field remains unchanged .

iv)

energy stored in first case = Q² / 2C

In the second case energy stored = Q² / 2x2C

so energy stored becomes half .

in this system, potential and kinetic energy are ____ proportional.

Answers

Answer:

Inversely proportional

Explanation:

P.E ∞ h

K.E ∞ v

v ∞ 1/h

Therefore

K.E ∞ 1/h

Then

P.E ∞ 1/(K.E)

Answer:

Inversely

Explanation:

You are hiking in a canyon and you notice an echo. You decide to let out a yell and notice it took 2 seconds before you heard the echo of your yell. How far away is the canyon wall that reflected your yell

Answers

Answer:

d = 343 m

Explanation:

Given that,

You notice that an echo took 2 seconds before you heard the echo of your yell.

We need to find that how far away is the canyon wall that reflected your yell. It means we need to find the distance.

The distance covered by an object is given by :

d = v × t

v is speed of sound in air, v = 343 m/s

The sound took 1 s to reach the wall and 1 s back to you.

It means that,

d = 343 × 1

d = 343 m

So, canyon will reflect your yell at a distance of 343 m

give an example of a balanced force and explain what makes it a balanced force

Answers

When two forces are the same strength but act in opposite direction, they are called balanced forces. Again, tug-of-war is a perfect example. If the people on each side of the rope are pulling with the same strength, but in the opposite direction, the forces are balanced. The result is no motion.

ball is thrown upward from a window that is 12 m above the ground.  The ball reaches a maximum height of 4 m above the window before falling all the way down to the ground.  What distance did the ball travel?​

Answers

Answer:

20 m

Explanation:

The ball travels 4 m up, then 16 m down.  It travels a total distance of 20 m.

Sound waves move the fastest through which medium?

Answers

Answer:

Sound travels fastest through solids.

Explanation:

This is because molecules in a solid medium are much closer together than those in a liquid or gas, allowing sound waves to travel more quickly through it. In fact, sound waves travel over 17 times faster through steel than through air.

Sound waves move the fastest through the solid. The speed of the sound wave  in the liquid and gas is low,

What is sound wave?

A sound wave is produced when a medium begins to vibrate. When an entity vibrates, a pressure wave is formed, which causes sound.

Solids transmit sound the fastest. Because the molecules in a solid medium are much closer together than in a liquid or gas, sound waves can move through it much faster.

Hence, sound waves move the fastest through the solid.

To learn more about the sound wave, refer to the link;

https://brainly.com/question/11797560

#SPJ2

A 30-cm long string, with one end clamped and the other free to move transversely, is vibrating in its second harmonic. The wavelength of the constituent traveling waves is:

Answers

Answer:

[tex]\lambda[/tex] = 40 cm

Explanation:

given data

string length = 30 cm

solution

we take here equation of length that is

L = [tex]n \times \frac{1}{4} \lambda[/tex]     ...............1

so

total length will be here

[tex]L = \frac{\lambda}{2} + \frac{\lambda}{4}\\[/tex]

[tex]L = \frac{3 \lambda }{4}[/tex]

so [tex]\lambda[/tex]  will be

[tex]\lambda = \frac{4L}{3}\\\lambda = \frac{4\times 30}{3}[/tex]

[tex]\lambda[/tex] = 40 cm

state the reason why wick lamps are made of cotton

Answers

Answer:

Reason:- We use cotton to make the wick of a spirit lamp because cotton has thread strands which act like fine capillaries and help in drawing up a steady supply of oil in the lamp for burning by capillary action

Explanation:

as fast as you can find the answer​

Answers

Answer:

Explanation:

a) From the diagram, the load will be expressed in newton. The load will be the weight of the box on the inclined plane.

Load = mass * acceleration due to gravity.

Given the mass of the object = 100kg

acceleration due to gravity = 9.8m/s²

Load (in Newton) = 100*9.8

Load (in Newton) = 980N

b) The formula for calculating the velocity ratio of an inclined plane is expressed as VR = 1/sinθ where θ is the angle of inclination.

Given θ = 30°,

VR = 1/sin30°

VR = 1/0.5

VR = 1/(1/2)

VR = 1* 2/1

VR = 2

The velocity ratio is 2.

c) Length of the inclined plane can be calculated using the SOH, CAH, TOA trigonometry identity.

According to SOH, sinθ = opposite/hypotenuse

sin30°  = 1/2 = opp/hyp

This shows that the opposite side of the triangle is 1 and the hypotenuse is 2. The length if the inclined is the length of the longest side i.e the hypotenuse. Hence the length of the inclined plane is 2m

d) Mechanical Advantage is the ratio of the load to the effort applied on an object.

Given the Load = 980N and the effort applied to the load on the incline plane = 400N

MA = Load/Effort

MA = 980/400

MA = 2.45

e) Efficiency = MA/VR * 100

Efficiency = 2.45/2 * 100

Efficiency  = 122.5%

anyone can solve these numerical please.​

Answers

Explanation:

2. Sum the torques about the fulcrum.

(450 N) (2 m) − (350 N) x = 0

x = 2.57 m

3. Sum the torques about the fulcrum.

(3600 N) (0.20 m) − F (0.90 m) = 0

F = 800 N

Mechanical advantage is the ratio between the load force and effort force.

MA = 3600 N / 800 N

MA = 4.5

Velocity ratio is the mechanical advantage divided by efficiency.  Assuming the lever is 100% efficient:

VR = 4.5 / 1

VR = 4.5

4. Mechanical advantage is the ratio between the load force and effort force.

MA = 900 N / 600 N

MA = 1.5

The velocity ratio is the distance moved by the effort divided by the distance moved by the load.  For a 3 pulley system, VR = 3.

Efficiency is mechanical advantage divided by velocity ratio.

e = 1.5 / 3

e = 0.50

5. Sum the torques about the fulcrum.

(-300 N) (0.10 m) + F (0.03 m) = 0

F = 1000 N

A 30-µF capacitor is charged to an unknown potential V and then connected across an initially uncharged 10-uF capacitor. If the final potential difference across the .10-µF capacitor is 20 V, determine V

Answers

Answer:

V = 26.6 volts

Explanation:

Let Initial Potential Difference be V.

Charge (Q) accumulated in 30 mF Capacitor =

Q = C * V

Q= 30 * V

Now, Common Potential after connecting to uncharged 10mF capacitor in parallel = 20 Volt

Total Charge =Total Capacity * Common Potential

30 * V = ( 30 + 10) * 20

V = 26.6 volts

The unknown potential across the 30-µF capacitor is 6.67 V.

The given parameters;

initial capacitance of the capacitor, C = 30 µFunknown potential in the 30 µF capacitor  = V₁potential difference in 10 µF capacitor = 20 V

Since the potential difference between the two capacitors are different, the two capacitors are in series connection.

In series circuit arrangement, the quantity of charge flowing in each capacitor is the same.

[tex]Q_{30\ \mu F} = Q_{10 \ \mu F}[/tex]

[tex]Q_{10 \ \mu F} = CV = 10\times 10^{-6} \times 20 = 0.0002 \ C[/tex]

The potential difference are different and the total potential is given as;

[tex]V_{T} = V_1 + V_2\\\\V_1 = \frac{Q}{C_1} \\\\V_2 = \frac{Q}{C_2} \\\\V_1+V_2 = \frac{Q}{C_1} + \frac{Q}{C_2}\\\\V_1 + V_2 = Q(\frac{1}{C_1} + \frac{1}{C_2} )\\\\V_1 + 20 = Q(\frac{1}{C_1} + \frac{1}{C_2} )\\\\V_1+ 20 = \frac{Q(C_2+ C_1)}{C_1 C_2} \\\\V_1 = \frac{Q(C_2+ C_1)}{C_1 C_2} - 20[/tex]

[tex]V_1 = \frac{0.0002(10\times 10^{-6}\ + \ 30\times 10^{-6})}{(30\times 10^{-6}) (10\times 10^{-6})} - 20\\\\V_1 = \frac{8\times 10^{-9}}{3\times 10^{-10}} - 20\\\\V_1 = 26.67 - 20\\\\V_1 = 6.67 \ V[/tex]

Thus, the unknown potential across the 30-µF capacitor is 6.67 V.

Learn more here:https://brainly.com/question/23899758

If you told a policeman about a car traveling 44.704 m/s (100 mph) that was traveling in an eastward direction, you would be describing the car's ___.

Answers

Answer:

Velocity

Explanation:

You would be describing the velocity of the car.

Velocity in physics is defined as Vector quantity that describes the displacement of an object with respect to the time it takes to attain it. Displacement is the addition of direction to the speed of an object. The displacement is noted in the question, "traveling eastward". While it is stated that the car travels at 44.704 m/s. Ordinarily, it would have been tagged speed, if not for the direction added to it which makes it velocity.

I hope you understand.

Other Questions
On July 1, Year 1, Yellow Rose Corp. paid $25,000 cash for a machine and paid an additional 8% sales tax. On the same date, an electrician was paid $1,000 to install custom switches to enhance the functionality of the machine. Yellow Rose estimates a five-year useful life, uses straight-line depreciation, and expects a $2,000 salvage value. The machine was placed in service on October 1, Year 1. Yellow Rose has a calendar year-end.On December 31, Year 2, the machine was sold for $14,000 cash. Depreciation expense for Year 2 was properly recorded.Use the data above to prepare each of the journal entries for Yellow Rose specified below.1. Prepare the journal entry to record the cost of the machine.2. Prepare the journal entry to record the Year 1 depreciation for the machine.3. Prepare the journal entry to record the sale of the machine. _____ refers to the growth and spread of investment, trade, production, communication, and new technology around the world. The following diagram shows the lines x 2y 4 = 0, x + y = 5 and the point P(1, 1). A line is drawn from P to intersect with x 2y 4 = 0 at Q, and with x + y = 5 at R, so that P is the midpoint of [QR]. Find the exact coordinates of Q and of R. What protocol communicates data between routers representing the edges of autonomous systems?Distance-vectorLink stateInterior gatewayExterior gateway Please help correct answer gets brainliest. Can somebody translate this (correct) to French: - I am looking for a tutor or I want to tutor in French - This group is intended for anyone who wants to give or receive tutoring in the Ireland. This group only serves for the first contact between students, pupils and their parents for every educational level. Also for every other subject that has to do with tutoring. Enter your REGION in capital letters, followed by your TARGET GROUP and the additional INFO. The price is mutually negotiable and depends on various factors such as subject, age, distance, etc. - New! Are you looking for a tutor or do you want to tutor in French? Join the group below! which promotes a more substainable use of resource solution for x- 4 is equal to 10 Nate is creating a PSA about building a "green roof. Which source is most reliable for his research? a blog post written by a community gardener a .com website that advertises fertilizer a .gov or .org website about ecological roofs a book featuring photos of different styles of roof A point (x,y) is a distance of 6 units from the x-axis. It is a distance of 5 units from the point (8,3). It is a distance [tex]\sqrt{n}[/tex] from the origin. Given that x A baseball is thrown into the air from the top of a 224-foot tall building. The baseball's approximate height over time can be represented by the quadratic equation h(t) = -16t2 + 80t + 224, where t represents the time in seconds that the baseball has been in the air and h(t) represents the baseball's height in feet. When factored, this equation is h(t) = -16(t - 7)(t + 2). What is a reasonable time for it to take the baseball to land on the ground? what is equivlent to 12x+(7)214x(2) The graph below shows Roy's distance from his office (y), in miles, after a certain amount of time (x), in minutes: Graph titled Roys Distance Vs Time shows 0 to 10 on x and y axes at increments of 1.The label on x axis is time in minutes and that on y axis is Distance from Office in miles. Lines are joined at the ordered pairs 0, 0 and 1, 1 and 2, 2 and 3, 3 and 4, 4 and 5, 4 and 6, 4 and 7, 4.5 and 7.5, 5 and 8, 6. Four students described Roy's motion, as shown in the table below: Student Description Peter He drives a car at a constant speed for 4 minutes, then stops at a crossing for 6 minutes, and finally drives at a variable speed for the next 2 minutes. Shane He drives a car at a constant speed for 4 minutes, then stops at a crossing for 2 minutes, and finally drives at a variable speed for the next 8 minutes. Jamie He drives a car at a constant speed for 4 minutes, then stops at a crossing for 6 minutes, and finally drives at a variable speed for the next 8 minutes. Felix He drives a car at a constant speed for 4 minutes, then stops at a crossing for 2 minutes, and finally drives at a variable speed for the next 2 minutes. Which student most accurately described Roy's motion? Peter Shane Jamie Felix Which of the following reasons would cause a company to reject an offer to accept business at a special price?a. The additional sales will increase differential income. b. The additional sales will not increase fixed expenses c. The additional sales will increase fixed expenses d. The additional sale will not conflict with regular sales. If someone loathes snakes, would that person be likely to adopt a snake as a pet? The value of y varies jointly with x and z. If y = 7 when z = 196 and x = 2, find the value of y when x = 3 and z = 336. I will rate you brainliest Assume a corporation has earnings before depreciation and taxes of $123,000, depreciation of $41,000, and that it has a 35 percent tax bracket. a. Compute its cash flow using the following format. (Input all answers as positive values.) b. How much would cash flow be if there were only $21,000 in depreciation Which is NOT true of balanced forces?A. Balanced forces will cause the motion of an object toincreaseB. Balanced forces are two equal forces pushing againsteach other on an object,C. Balanced forces do not cause a change in the motion ofan object A mixture of 50ml of 0.1M HCOOH and 50ml of 0.05M NaOH is equivalent to any know how to get rid if a blocked nose if blowing it isnt working