Answer:
the main surveying instruments is use around the world are the theodolite, measuring tape, total station, 3D scanners ,GPS/GNSS, level and rod.Most instruments screw into a tripod when in use.A wedge would be best described as
A wheel and axle used to cTeate a rotary motion
A lever arm fixed to a shaft
A triangle shaped tool that functions as an inclined plane
A rectangular shaped tool that functions as a pulley
Answer:
A rectangular shaped tool that functions as a pulley.
Explanation:
i beleive
Determine the size of memory needed for CD recording of a piece of music, which lasts for 26 minutes, is done with a 20-bit Analog-to-Digital Converter (ADC) in stereo (2 channels), at the rate of 44.1 kSa/s, with the compression factor 6 (allow 10% error margin).
Answer: the size of memory needed for the CD recording is 28.7 MB
Explanation:
so in the case of stereo, the bitrate is;
⇒ 26 × 60 × 44.1 × 10³ × 2
= 137592 × 10³
for 10 bit
⇒ 137592 × 10³ × 10
= 1375920 × 10³ bits
now divide by 8 (convert to bytes)
⇒ (1375920 × 10³) / 8
= 171,990,000 BYTE
divide by 1000 (convert to kilobytes)
= 171,990,000 / 1000
= 171,990 KILOBYTES
now Given that, the compression ratio is 6
so
171,990 / 6
= 28665 KB
we know that. 1 MB = 1000 KB
x MB = 28665 KB
x MB = 28665 / 1000
⇒ 28.665 MB ≈ 28.7 MB
Therefore the size of memory needed for the CD recording is 28.7 MB
Compute the weight fraction of graphite, in a 3 wt% C Ferritic Gray cast iron, assuming that all the carbon exists as the graphite phase. Assume densities of 7.9 and 2.3 g/cm3 for ferrite and graphite, respectively.
Answer:
9.60%
Explanation:
Computation for the weight fraction of graphite
First step
Computation for the mass fraction for Wa using this formula
Wa=Cg-Co/Cg-Ca
Let plug
Wa=10-3/100-0
Wa=0.97
Computation for the mass fraction for Wg using this formula
Wg=Co-Ca/Cg-Ca
Let plug in the formula
Wg=3-0/100-0
Wg=0.03
Second step is to convert the mass fraction to Volume Fraction using this formula
Volume Fraction =[Wg/Pg÷(Wa/Pa)+(Wg/Pg)]*100
Let plug in the formula
Volume =[0.03/2.3 ÷(0.97/7.9)+(0.03/2.3)]*100
Volume=[0.0130435÷0.1227848+0.0130435]*100
Volume=[0.0130435÷0.135828]*100
Volume=0.096*100
Volume=9.60%
Therefore the weight fraction of graphite will be 9.60%
4. The process of heating milk to kill microorganisms that cause spoilage and disease without affecting its nutritional value is called
A. Homogenization
B. Pasteurization
C. Boiling
D. Poaching
Answer:
I think the answer is C. Boiling but I'm not 100% sure.
a cantilever beam 1.5m long has a square box cross section with the outer width and height being 100mm and a wall thickness of 8mm. the beam carries a uniform load of 6.5kN/m along the entire length and, in the same direction, a concentrated force of 4kN at the free end. (a) determine the max bending stress (b) determine the max transervse shear stress (c) determine the max shear stress in the beam
Answer:
a) 159.07 MPa
b) 10.45 MPa
c) 79.535 MPa
Explanation:
Given data :
length of cantilever beam = 1.5m
outer width and height = 100 mm
wall thickness = 8mm
uniform load carried by beam along entire length= 6.5 kN/m
concentrated force at free end = 4kN
first we determine these values :
Mmax = ( 6.5 *(1.5) * (1.5/2) + 4 * 1.5 ) = 13312.5 N.m
Vmax = ( 6.5 * (1.5) + 4 ) = 13750 N
A) determine max bending stress
б = [tex]\frac{MC}{I}[/tex] = [tex]\frac{13312.5 ( 0.112)}{1/12(0.1^4-0.084^4)}[/tex] = 159.07 MPa
B) Determine max transverse shear stress
attached below
ζ = 10.45 MPa
C) Determine max shear stress in the beam
This occurs at the top of the beam or at the centroidal axis
hence max stress in the beam = 159.07 / 2 = 79.535 MPa
attached below is the remaining solution
If most wildfires are suppressed (all fires are put out) for many years, how does the risk of wildfire in the area change in the future?
There will be a higher risk of wildfires
There will be a lower risk of wildfires
There is no difference in risk
Explain your answer.
Answer:
there is no difference in risk
Explanation:
even though they put out the fires, if they don't get rid of the source from which the wildfires comes from then wildfires wont stop coming
The purpose of pasteurizing milk is to A. Kill pathogens B. Break down milk fat C. Add vitamins and minerals D. Prevent spoilage by sunlight
Answer:
The answer is A
Explanation:
The correct answer is A
According to the model rules section 240.15, rules of professional conduct, licensed professional engineers are obligated to:______
A. ensure that design docuiments and suirveys are reviewed by a panel of licensed engineers prior to affixing a seal of approval
B. express public opinions under the direction of an employer or client regardless of knowledge of subject matter
C. practice by perfonning services only in the areas of their competence and in accordance with the cuurent standards of technical
D. offer. give or solicit services directly or indirectly in order to secure work or other valuable or political considerations
Answer:
Option C (practice by..............technical) would be the appropriate choice.
Explanation:
A prerogative seems to be the discipline or nature of the design process to ensure. All certificates must, therefore, throughout compliance with current requirements including professional competence, express one's right and privilege of providing offers perhaps throughout the areas of qualified professionals.Some other alternatives that are given aren't connected to a particular scenario. But that's the best solution above.
Five identical keys are suspended from a balance, which is held horizontally as shown. The two keys on the left are attached to the balance 6 cm from the pivot and the three keys on the right are attached 5 cm from the pivot. What will happen when the person lets go of the balance beam?
Answer:
movement in clockwise direction.
Explanation:
The following parameters or information are given from the question above, they are:
[1]. There are two identical keys, [2]. two out of the five keys are attached to 6cm from the pivot, [3]. three keys out of the five keys on the right are attached 5 cm.
Therefore, considering the moment of force, the two keys on the left = 2 × 6 = 12.
Also, considering the moment of force, the 3 keys on the right = 3 × 5 = 15.
Therefore, we have more weight on the right keys. So, in order to balance the force there must be movement in clockwise direction.
