Answer:
A. falling water
Explanation:
I got it right on Edgenuity. Good luck on your quiz.
In hydroelectric plants, water falls on turbine and makes it rotate. In generator, this mechanical energy transforms into electrical energy.
What is hydroelectric power?Hydroelectric power is generated by turbines that turn the potential energy of falling or swiftly flowing water into mechanical energy, which is then used to power generators. The most popular renewable energy source in the early 21st century was hydroelectricity, which in 2019 accounted for more than 18% of the world's total power producing capacity.
Water is gathered or stored at a higher elevation during the production of hydroelectric power and then transported through substantial pipes or tunnels (penstocks) to a lower elevation; the difference between these two elevations is referred to as the head. The falling water turns turbines as it nears the bottom of the pipelines. In turn, the turbines power generators, which transfer the mechanical energy of the turbines into electricity.
Learn more about hydroelectric power here:
https://brainly.com/question/15228003
#SPJ2
A cobalt-60 source with activity 2.60×10-4 Ci is embedded in a tumor that has
mas 0.20 kg. The source emits gamma photons with average energy 1.25 MeV.
Half the photons are absorbed in the tumor, and half escape.
i. What energy is delivered to the tumor per second? [4 marks]
ii. What absorbed dose, in rad, is delivered per second? [2 marks]
iii. What equivalent dose, in rem, is delivered per second if the RBE for
these gamma rays is 0.70? [2 marks]
Page 6 of 7
iv. What exposure time is required for an equivalent dose of 200 rem? [2
marks]
B. A laser with power output of 2.0 mW at a wavelength of 400 nm is projected
onto a Calcium metal. The binding energy is 2.31 eV.
i. How many electrons per second are ejected? [6 marks]
ii. What power is carried away by the electrons? [4 marks]
C. A hypodermic needle of diameter 1.19 mm and length 50 mm is used to
withdraw blood from a patient? How long would it take for 500 ml of blood to be
taken? Assume a blood viscosity of 0.0027 Pa.s and a pressure in the vein of
1,900 Pa. [10 marks]
D. A person with lymphoma receives a dose of 35 gray in the form of gamma
radiation during a course of radiotherapy. Most of this dose is absorbed in 18
grams of cancerous lymphatic tissue.
i. How much energy is absorbed by the cancerous tissue? [2 marks]
ii. If this treatment consists of five 15-minute sessions per week over the
course of 5 weeks and just one percent of the gamma photons in the
gamma ray beam are absorbed, what is the power of the gamma ray
beam? [4 marks]
iii. If the gamma ray beam consists of just 0.5 percent of the photons
emitted by the gamma source, each of which has an energy of 0.03
MeV, what is the activity, in Curies, of the gamma ray source? [4 marks]
E. A water heater that is connected across the terminals of a 15.0 V power supply
is able to heat 250 ml of water from room temperature of 25°C to boiling point
in 45.0 secs. What is the resistance of the heater? The density of water is 1,000
kg/m2 and the specific heat capacity of water is 4,200 J/kg/°C. [10 marks]
Answer:
A i. E = 9.62 × 10⁻⁷ J/s
ii. The absorbed dose is 4.81 × 10⁻⁶ Gy
iii. The equivalent dose is 3.37 × 10⁻⁴ rem/s
iv. t = 593471.81 seconds
B. i. 4.025 × 10¹⁵/s
ii. 0.512 mW
C. 7218092.2 seconds
D. i. 6.3 × 10⁻¹ J
ii. 1.4 × 10⁻² W
iii. 1.57 × 10³ Curie
E. 0.129 Ω
Explanation:
The given parameters are;
Mass of tumor = 0.20 kg
Activity of Cobalt-60 = 2.60 × 10⁻⁴ Ci
Photon energy = 1.25 MeV
(i) The energy, E, delivered to the tumor is given by the relation;
[tex]E = \frac{1}{2}\left (Number \, of \, decay / seconds \right )\times \left (Energy \, of \, photon \right )[/tex]
[tex]E = \frac{1}{2}\left (2.6\times 10^{-4}Ci )\times \left (\frac{3.70\times 10^{10}decays/s}{1 Ci} \right )\times 1.25\times 10^{6}eV\times \frac{1.6\times 10^{-19}J}{1eV}[/tex]
E = 9.62 × 10⁻⁷ J/s
(ii) The equation for absorbed dose is given as follows;
Absorbed dose, D, in Grays Gy = (Energy Absorbed Joules J)/Mass kg
Therefore, absorbed dose = (9.62 × 10⁻⁷ J/s)/( kg) = 4.81 × 10⁻⁶ Gy
1 Gray = 100 rad
4.81 × 10⁻⁷ Gy = 100 × 4.81 × 10⁻⁶ = 4.81 × 10⁻⁴ rad/s
(iii) Equivalent dose, H, is given by the relation;
H = D × Radiation factor, [tex]w_R[/tex]
∴ H = 0.7 × 4.81 × 10⁻⁴ rad/s = 3.37 × 10⁻⁴ Sv = 3.37 × 10⁻⁴ rem/s
(iv) The exposure time required for an equivalent dose of 200 rem is given as follows;
[tex]\dot{H} = \dfrac{H}{t}[/tex]
Therefore;
[tex]t= \dfrac{200}{{3.37 \times 10^{-4}} } = 593471.81 \, s[/tex]
∴ t = 6.9 days
B. The number of electrons ejected is given by the relation;
[tex]N = \frac{P}{E} = \frac{P \times \lambda}{hc}[/tex]
[tex]N = \dfrac{2.0 \times 10^{-3} \times 400 \times 10^{-9}}{6.626 \times 10^{-34} \times 3 \times 10^8} = 4.025 \times 10^{15}/s[/tex]
(ii) The power carried by the electron
The energy carried away by the electrons is given by the relation;
[tex]KE_e = hv - \Phi[/tex]
[tex]KE_e = \frac{6.626 \times 10^{-34} \times 3 \times 10^8}{400 \times 10^{-9}} - 2.31 \times \frac{1.6 \times 10 ^{-19} }{1}[/tex]
[tex]KE_e = 4.9695 \times 10^{-19} - 3.696 \times 10 ^{-19} = 1.2735 \times 10^{-19} J[/tex]
Power, P[tex]_e[/tex], carried away by the electron = 4.025 × 10¹⁵ × 1.2735 × 10⁻¹⁹ = 0.512 mW
C. The given parameters are;
d = 1.19 mm, ∴ r = 1.19/2 = 0.595 × 10⁻³ m
l = 50 mm = 5 × 10⁻³ m
V = 500 ml = 5 × 10⁻⁴ m³
η = 0.0027 Pa
p = 1,900 Pa.
[tex]\dfrac{V}{t} = \dfrac{\pi }{8} \times \dfrac{P/l}{\eta } \times r^4[/tex]
[tex]t = \dfrac{8\times \eta\times V\times l }{\pi \times P \times r^4}[/tex]
[tex]t = \dfrac{8\times 0.0027 \times 5 \times 10^{-4} \times 5 \times 10^{-2} }{\pi \times 1900 \times (0.595 \times 10^{-4} )^4}[/tex]
t = 7218092.2 seconds
D) i. Energy absorbed is given by the relation;
E = m×D
Where:
D = 35 Gray = 35 J/kg
m = 18 g = 18 × 10⁻³ kg
∴ E = 35 × 18 × 10⁻³ = 6.3 × 10⁻¹ J
ii. Total time for treatment = 15 × 5 = 75 minutes
Energy absorbed = 6.3 × 10⁻¹ × 100 = 63 J
Power = Energy(in Joules)/Time (in seconds)
∴ Power = 63/(75×60) = 1.4 × 10⁻² W
iii. Whereby the power is provided by 0.5% of the photons emitted by the source, we have;
[tex]P_{source}= \frac{P_{beam}}{0.005} =\frac{0.0014}{0.005} =0.28 \, W[/tex]
1 MeV = 1.60218 × 10⁻¹³ J
0.03 MeV = 0.03 × 1.60218 × 10⁻¹³ J = 4.80654 × 10⁻¹⁵ J/photon
Therefore, the number of disintegration per second = 0.28 J/s ÷ 4.80654 × 10⁻¹⁵ J/photon = 5.83 × 10¹³ disintegrations per second
1 Curie = 3.7 × 10¹⁰ disintegrations per second
Hence, 5.83 × 10¹³ disintegrations per second = (5.83 × 10¹³)/(3.7 × 10¹⁰) Curie
= 1.57 × 10³ Curie
E. The parameters given are;
Density of water = 1000 kg/m³
Volume of water = 250 ml = 0.00025 m³
Initial temperature, T₁, = 25°C
Final temperature, T₂, = 100°C
Change in temperature, ΔT = 100 - 25 = 75°
Specific heat capacity of the water = 4200 J/kg/°C
Mass of water = Density × Volume = 1000 × 0.00025 = 0.25 kg
∴ Heat supplied = 4200 × 0.25 × 75 = 78,750 J
Time to heat the water = 45.0 sec
Therefore, power = Energy/time = 78750/45 = 1750 W
The formula for electrical power = I²R =VI = V²/R
Therefore, where V = 15.0 V, we have;
15²/R = 1750
R = 15²/1750 = 0.129 Ω.
The resistance of the heater = 0.129 Ω.
A cylindrical specimen of some metal alloy having an elastic modulus of 108 GPa and an original cross-sectional diameter of 3.7 mm will experience only elastic deformation when a tensile load of 1890 N is applied. Calculate the maximum length of the specimen before deformation if the maximum allowable elongation is 0.45 mm.
Answer:
L= 276.4 mm
Explanation:
Given that
E= 180 GPa
d= 3.7 mm
F= 1890 N
ΔL= 0.45 mm
We know that ,elongation due to load F in a cylindrical bar is given as follows
[tex]\Delta L =\dfrac{FL}{AE}[/tex]
[tex]L=\dfrac{\Delta L\times AE}{F}[/tex]
Now by putting the values in the above equation we get
[tex]L=\dfrac{0.45\times 10^{-3}\times \dfrac{\pi}{4}\times (3.7\times 10^{-3})^2\times 108\times 10^9}{1890}\ m[/tex]
L=0.2764 m
L= 276.4 mm
Therefore the length of the specimen will be 276.4 mm
A turntable has a moment of inertia of 3.00 x 10-2 kgm2 and spins freely on a frictionless bearing at 25.0 rev/min. A 0.300 kg ball of putty is dropped vertically on the turntable and sticks at a point 0.10m from the center. The total moment of inertia of the system increases, and the turntable slows down. But by what factor does the angular momentum of the system change after the putty is dropped onto the turntable
Answer:
There will be no change in the angular momentum of the system.
Explanation:
Total angular momentum of the system will remain unchanged . We can apply law of conservation of momentum because no external torque is acting on the system . There is increase in the momentum of inertia due to dropping of ball of putty . In order to conserve angular momentum , the system decreases its angular velocity . Hence the final angular momentum remains unchanged .
An athlete is working out in the weight room. He steadily holds 50 kilograms above his head for 10 seconds. Which statement is true about this situation?
Answer:
Answer: the true statement form the given statements is “the athletes is not doing any work because he does not move weight”
Explanation:
The athlete isn’t doing any work because he doesn’t move the weight is the correct statement.
What is Work? Work is the energy transferred to or from an object via the application of force along a displacement.Work = Force x Displacement.How to solve this Problem?The weight of an object given is 50kgsThe time of holding an object given is 10 secondsWe need to justify the statements
Here ,
There is no displacement that means displacement is zero.If displacement is zero then work done will also be zeroHence there is no work done by the athlete
Therefore ,The athlete isn’t doing any work because he doesn’t move the weight is the correct statement
Learn more about Work done here
https://brainly.com/question/25573309
#SPJ2
A 200.0 g block rests on a frictionless, horizontal surface. It is pressed against a horizontal spring with spring constant 4500.0 N/m (assume that the spring is massless). The block is held in position such that the spring is compressed 4.00 cm shorter than its undisturbed length. The block is suddenly released and allowed to slide away on the frictionless surface. Find the speed the block will be traveling when it leaves the spring.
Answer:
6 m/s
Explanation:
Given that :
mass of the block m = 200.0 g = 200 × 10⁻³ kg
the horizontal spring constant k = 4500.0 N/m
position of the block (distance x) = 4.00 cm = 0.04 m
To determine the speed the block will be traveling when it leaves the spring; we applying the work done on the spring as it is stretched (or compressed) with the kinetic energy.
i.e [tex]\frac{1}{2} kx^2 = \frac{1}{2} mv^2[/tex]
[tex]kx^2 = mv^2[/tex]
[tex]4500* 0.04^2 = 200*10^{-3} *v^2[/tex]
[tex]7.2 =200*10^{-3}*v^{2}[/tex]
[tex]v^{2} =\frac{7.2}{200*10^{-3}}[/tex]
[tex]v =\sqrt{\frac{7.2}{200*10^{-3}}}[/tex]
v = 6 m/s
Hence,the speed the block will be traveling when it leaves the spring is 6 m/s
An astronaut is being tested in a centrifuge. The centrifuge has a radius of 11.0 m and, in starting, rotates according to θ = 0.260t2, where t is in seconds and θ is in radians. When t = 2.40 s, what are the magnitudes of the astronaut's (a) angular velocity, (b) linear velocity, (c) tangential acceleration, and (d) radial acceleration?
Answer:
a) 1.248 rad/s
b) 13.728 m/s
c) 0.52 rad/s^2
d) 17.132m/s^2
Explanation:
You have that the angles described by a astronaut is given by:
[tex]\theta=0.260t^2[/tex]
(a) To find the angular velocity of the astronaut you use the derivative og the angle respect to time:
[tex]\omega=\frac{d\theta}{dt}=\frac{d}{dt}[0.260t^2]=0.52t[/tex]
Then, you evaluate for t=2.40 s:
[tex]\omega=0.52(2.40)=1.248\frac{rad}{s}[/tex]
(b) The linear velocity is calculated by using the following formula:
[tex]v=\omega r[/tex]
r: radius if the trajectory of the astronaut = 11.0m
You replace r and w and obtain:
[tex]v=(1.248\frac{rad}{s})(11.0m)=13.728\frac{m}{s}[/tex]
(c) The tangential acceleration is:
[tex]a_T=\alpha r\\\\\alpha=\frac{\omega^2}{2\theta}=\frac{(1.248rad/s)^2}{2(0.260(2.40s)^2)}=0.52\frac{rad}{s^2}[/tex]
(d) The radial acceleration is:
[tex]a_r=\frac{v^2}{r}=\frac{(13.728m/s)^2}{11.0m}=17.132\frac{m}{s^2}[/tex]
I need some help!!!!!!!!!
Answer:
The Object will immediately begin moving toward the left
Explanation:
Because the force of thirteen is greater than ten and applied to the opposite side
If Jim could drive a Jetson's flying car at a constant speed of 440 km/hr across oceans and space, approximately how long (in millions of years, in 106 years) would he take to drive to a nearby star that is 12.0 light-years away? Use 9.461 × 1012 km/light-year and 8766 hours per year (365.25 days).
Answer:
t = 2.94 x 10⁶ years
Explanation:
The equation used in the case of constant speed is:
s = vt
t = s/v
where,
s = distance = 12 light years
s = (12 light years)(9.461 x 10¹² km/light year) = 113.532 x 10¹² km
v = speed = 440 km/hr
t = time passed = ?
Therefore,
t = (113.532 x 10¹² km)/(440 km/hr)
t = 2.58 x 10¹¹ hr
Now, converting it to years:
t = (2.58 x 10¹¹ hr)(1 year/8766 hr)
t = 2.94 x 10⁶ years
Two wires, both with current out of the page, are next to one another. The wire on the left has a current of 1 A and the wire on the right has a current of 2 A. We can say that:
A. The left wire attracts the right wire and exerts twice the force as the right wire does.
B. The left wire attracts the right wire and exerts half the force as the right wire does.
C. The left wire attracts the right wire and exerts as much force as the right wire does.
D. The left wire repels the right wire and exerts twice the force as the right wire does.
E. The left wire repels the right wire and exerts half the force as the right wire does.
F. The left wire repels the right wire and exerts as much force as the right wire does.
Answer:
C. The left wire attracts the right wire and exerts as much force as the right wire does.
Explanation:
To know what is the answer you first take into account the magnetic field generated by each current, for a distance of d:
[tex]B_1=\frac{\mu_oI_1}{2\pi d}=\frac{\mu_o}{2\pi d}(1A)\\\\B_2=\frac{\mu_oI_2}{2\pi d}=\frac{\mu_o}{2\pi d}(2A)=2B_1\\\\[/tex]
Next, you use the formula for the magnetic force produced by the wires:
[tex]\vec{F_B}=I\vec{L}\ X \vec{B}[/tex]
if the direction of the L vector is in +k direction, the first wire produced a magnetic field with direction +y, that is, +j and the second wire produced magnetic field with direction -y, that is, -j (this because the direction of the magnetic field is obtained by suing the right hand rule). Hence, the direction of the magnetic force on each wire, produced by the other one is:
[tex]\vec{F_{B1}}=I_1L\hat{k}\ X\ B_2(-\hat{j})=I_1LB_2\hat{i}=(2A^2)\frac{L\mu_o}{2\pi d}\hat{i}\\\\\vec{F_{B2}}=I_2L\hat{k}\ X\ B_2(\hat{j})=I_2LB_1\hat{i}=-(2A^2)\frac{L\mu_o}{2\pi d}\hat{i}[/tex]
Hence, due to this result you have that:
C. The left wire attracts the right wire and exerts as much force as the right wire does.
Dual Nature of Light
Assignment
Active
Explaining the Nature of Light
Why do scientists believe that light is made of streams of
particles?
To understand thermal linear expansion in solid materials. Most materials expand when their temperatures increase. Such thermal expansion, which is explained by the increase in the average distance between the constituent molecules, plays an important role in engineering. In fact, as the temperature increases or decreases, the changes in the dimensions of various parts of bridges, machines, etc., may be significant enough to cause trouble if not taken into account. That is why power lines are always sagging and parts of metal bridges fit loosely together, allowing for some movement. It turns out that for relatively small changes in temperature, the linear dimensions change in direct proportion to the temperature.
For instance, if a rod has length L0 at a certain temperature T0 and length L at a higher temperature T, then the change in length of the rod is proportional to the change in temperature and to the initial length of the rod: L - L0 = αL0(T - T0),
or
ΔL = αL0ΔT.
Here, α is a constant called the coefficient of linear expansion; its value depends on the material. A large value of α means that the material expands substantially as the temperature increases; smaller values of α indicate that the material tends to retain its dimensions. For instance, quartz does not expand much; aluminum expands a lot. The value of α for aluminum is about 60 times that of quartz!
Questions:
A) Compared to its length in the spring, by what amount ΔLwinter does the length of the bridge decrease during the Teharian winter when the temperature hovers around -150°C?
B) Compared to its length in the spring, by what amount ΔLsummer does the length of the bridge increase during the Teharian summer when the temperature hovers around 700°C?
Answer:
Check the explanation
Explanation:
Kindly check the attached image below to see the step by step explanation to the question above.
The main component of all computer memory is
Answer: R.A.M
Explanation:
A particular coil has 100 turns and a diameter of 6.0 m. When it's time for a measurement, a 4.5 A current is turned on. The large diameter of the coil means that the field in the water flowing directly above the center of the coil is approximately equal to the field in the center of the coil. The field is directed downward and the water is flowing east. The water is flowing above the center of the coil at 1.5 m/s .
What is the magnitude of the field at the center of the coil?
Answer:
The magnetic field at the center of the coil = 5.23 * 10 ^ -5 T
Explanation:
Information from the question:
Number of turns of the coil = 100 turns
The diameter of the coil = 6 m
The radius of the coil = diameter / 2 = 3 m
The coil current = 2.5 A
Formula : The Magnetic field at the center of the coil =
k * number of turns * current / 2 * radius
Therefore, The Magnetic field at the center of the coil=
(4 * [tex]\pi[/tex] * 10 ^ -7 * 100 * 2.5 ) / (2 * 3)
The Magnetic field at the center of the coil = 5.23 * 10 ^ -5 T
This is a measure of quantity of matter
Answer:
Mass
Explanation:
Mass is the measure of amount of matter contained within any substance and hence mass determines the weight. Unit of mass is kilogram as per ISI system of units.
Mass is measured through a balance. The more is the mass of an object, the more the balance tilts towards the object side.
Weight is equal to product of mass and the gravitational constant i.e 9.8m/s^2
What is an independent variable?
A. A variable that is intentionally changed during an experiment
B. A variable that depends on the experimental variable
C. A variable that is not used in an experiment
D. A variable that is unknown during the experiment
Answer:
The answer is A
Explanation:
Independent variables don't have to depend on other factors of the experiment because they're independent
Answer:
A.
Explanation:
Independent variables don't have to depend on other factors of the experiment because they're independent.
In this circuit the battery provides 3 V, the resistance R1 is 7 Ω, and R2 is 5 Ω. What is the current through resistor R2? Give your answer in units of Amps. An Amp is 1 Coulomb of charge flowing through a cross-sectional area of the wire per second - that's a lot of charge per second and will warm up a typical wire quite a bit! Most devices have circuits with larger resistors - kLaTeX: \OmegaΩ (103 LaTeX: \OmegaΩ) and MLaTeX: \OmegaΩ (106 LaTeX: \OmegaΩ) are common.
Answer:
The current pass the [tex]R_2[/tex] is [tex]I = 0.25 A[/tex]
Explanation:
The diagram for this question is shown on the first uploaded image
From the question we are told that
The voltage is [tex]V = 3V[/tex]
The first resistance is [tex]R_1 = 7 \Omega[/tex]
The second resistance is [tex]R_2 = 5 \Omega[/tex]
Since the resistors are connected in series their equivalent resistance is
[tex]R_{eq} = R_1 +R_2[/tex]
Substituting values
[tex]R_{eq} = 7 + 5[/tex]
[tex]R_{eq} = 12 \Omega[/tex]
Since the resistance are connected in serie the current passing through the circuit is the same current passing through [tex]R_2[/tex] which is mathematically evaluated as
[tex]I = \frac{V}{R_{eq}}[/tex]
Substituting values
[tex]I = \frac{3}{12}[/tex]
[tex]I = 0.25 A[/tex]
Match these items.
1 . pls help
asteroids
between Mars and Jupiter
2 .
fission
ice, dust, frozen gases
3 .
energy
sun's atmosphere
4 .
fusion
ability to do work
5 .
corona
splitting atoms
6 .
comets
the combining of atomic nuclei to form one nucleus
Answer:
Here's your answer :
Asteroids - Between mars and JupiterFission - splitting atomsEnergy - Sun's atmosphereFusion - The combining of atomic nuclei to form one nucleusCorona - Ability to do workComets - Ice, dust, frozen gaseshope it helps!
A 0.009 kg bullet fired through a door enters at 803 m/s and leaves at 617 m/s. If the door material is known to exert an average resistive force of 5620 N on bullets of this type at usual speeds, find the thickness of the door.
Answer:
The thickness of the door is 0.4230 m
Explanation:
Given;
mass of bullet, m = 0.009 kg
initial velocity of the bullet, u = 803 m/s
final velocity of the bullet, v = 617 m/s
average resistive force of the door on the bullet, F = 5620 N
Apply Newton's second law of motion;
Force exerted by the door on the bullet = Force of the moving bullet
F = ma
where;
F is applied force
m is mass
a is acceleration
Also, Force exerted by the door on the bullet = Force of the moving bullet
[tex]F =ma, \ But \ a =\frac{dv}{dt} = \frac{u-v}{t} \\\\F = \frac{m(u-v)}{t}[/tex]
where;
v is the final velocity of the bullet
u is initial velocity of the bullet
t is time
We need to calculate the time spent by the bullet before it passes through the door.
[tex]t = \frac{m(u-v)}{F} \\\\t = \frac{0.009(803-617)}{5620} = 0.0002979 \ s[/tex]
Distance traveled by the bullet within this time period = thickness of the door
This distance is equivalent to the product of average velocity and time
[tex]S = (\frac{u+v}{2}) t[/tex]
where;
s is the distance traveled
[tex]S = (\frac{u+v}{2}) t\\\\S = (\frac{803+617}{2}) 0.0002979\\\\S = 0.4230 \ m[/tex]
Therefore, the thickness of the door is 0.4230 m
Exercise should challenge your body and be at a greater intensity than your usual bif daily activity. Discuss
Answer:
A fan pushes hot air out of a vent and into a room. The hot air displaces cold air in the room, causing the cold air to move closer to the floor.
The hot air displacing the cold air is an example of transfer by
Explanation:
Is mercury (the planet) rocky or gaseous(meaning relating to or having the characteristics of a gas.)
Answer:
Mercury is rocky
Explanation:
Answer:
Rocky
Explanation:
It has no atmosphere so it cannot hold gas.
PIUDICITIS CONSECulvely and Circle your aliswers. Lilyo
proper significant digits.
53. When you turn on your CD player, the turntable accelerates from zero to 41.8 rad/s in
3.0 s. What is the angular acceleration?
or
Answer:
The angular acceleration of CD player is [tex]13.93\ rad/s^2[/tex].
Explanation:
Initial angular speed of a CD player is 0 and final angular speed is 41.8 rad/s. Time to change the angular speed is 3 s.
It is required to find the angular acceleration. The change in angular speed of the CD player divided by time taken is called its angular acceleration. It can be given by :
[tex]a=\dfrac{\omega_f-\omega_i}{t}\\\\a=\dfrac{41.8-0}{3}\\\\a=13.94\ rad/s^2[/tex]
So, the angular acceleration of CD player is [tex]13.93\ rad/s^2[/tex].
Newton's law of cooling states that the temperature of an object changes at a rate proportional to the difference between its temperature and that of its surroundings. Suppose that the temperature of a cup of coffee obeys Newton's law of cooling. If the coffee has a temperature of 210 degrees Fahrenheit when freshly poured, and 2.5 minutes later has cooled to 191 degrees in a room at 64 degrees, determine when the coffee reaches a temperature of 156 degrees.
Answer:
Explanation:
The problem is based on Newton's law of cooling .
According to Newton's law
dQ / dt = k ( T - T₀ ) ,
dT / dt = k' ( T - T₀ ) ; dT / dt is rate of fall of temperature.
T is average temperature of hot body , T₀ is temperature of surrounding .
In the first case rate of fall of temperature = (210 - 191) / 2.5
= 7.6 degree / s
average temperature T = (210 + 191) /2
= 200.5
Putting in the equation
7.6 = k' ( 200.5 - 64 )
k' = 7.6 / 136.5
= .055677
In the second case :---
In the second case, rate of fall of temperature = (191 - 156) / t
= 35 / t , t is time required.
average temperature T = (156 + 191) /2
= 173.5
Putting in the equation
35 / t = .05567 ( 173.5 - 64 )
t = 5.74 minute .
Part A - At what angle does it leave?
Part B - At what distance x does it exit the field?
Answer:
Total internal reflection (TIR) is the phenomenon that involves the reflection of all the incident light off the boundary. TIR only takes place when both of the following two conditions are met: the light is in the more dense medium and approaching the less dense medium.
Explanation: Hope i helped!!!
A steam engine takes in superheated steam at 270 °C and discharges condensed steam from its cylinder at 50 °C. The engine has an efficiency of 30%, and taken in 50 kJ from the hot steam per cycle. If a Carnot engine takes in the same amount of heat per cycle and operates at these temperatures, the work it can turn into is most likely to be:a) 15 kJ. b) 20 kJ. c) 10 kJ. d) 50 kJ.
Answer:
b) 20 kJ
Explanation:
Efficiency of carnot engine = (T₁ - T₂ ) / T₁ Where T₁ is temperature of hot source and T₂ is temperature of sink .
T₁ = 270 + 273 = 543K
T₂ = 50 + 273 = 323 K
Putting the given values of temperatures
efficiency = (543 - 323) / 543
= .405
heat input = 50 KJ
efficiency = output work / input heat energy
.405 = output work / 50
output work = 20.25 KJ.
= 20 KJ .
The instantaneous speed of a particle moving along one straight line is v(t) = ate−6t, where the speed v is measured in meters per second, the time t is measured in seconds, and the magnitude of the constant a is measured in meters per second squared. What is its maximum speed, expressed as a multiple of a? (Do not include units in your answer.)
Answer:
v_max = (1/6)e^-1 a
Explanation:
You have the following equation for the instantaneous speed of a particle:
[tex]v(t)=ate^{-6t}[/tex] (1)
To find the expression for the maximum speed in terms of the acceleration "a", you first derivative v(t) respect to time t:
[tex]\frac{dv(t)}{dt}=\frac{d}{dt}[ate^{-6t}]=a[(1)e^{-6t}+t(e^{-6t}(-6))][/tex] (2)
where you have use the derivative of a product.
Next, you equal the expression (2) to zero in order to calculate t:
[tex]a[(1)e^{-6t}-6te^{-6t}]=0\\\\1-6t=0\\\\t=\frac{1}{6}[/tex]
For t = 1/6 you obtain the maximum speed.
Then, you replace that value of t in the expression (1):
[tex]v_{max}=a(\frac{1}{6})e^{-6(\frac{1}{6})}=\frac{e^{-1}}{6}a[/tex]
hence, the maximum speed is v_max = ((1/6)e^-1)a
Which term BEST describes the movement of air from the ocean toward the land in the daytime? (AKS 4b DOK 1) *
1 point
Sea breeze
Land Breeze
Valley Breeze
Current Breeze
Answer:
Option A, Sea Breeze
Explanation:
Ssea breeze is a wind that blows from the ocean or any water body to the nearby land mass. This breeze is cold as compared to the air on land. The water in water bodies has high specific heat capacity and hence takes longer time to cool as compared to the surrounding objects. The warmer air over the land rises upward thereby reducing the pressure on land and hence the sea breeze starts flowing from region of high pressure (i.e above the water body) towards the low pressure region that is the land.
Hence, option A is correct
A Texas cockroach of mass 0.157 kg runs counterclockwise around the rim of a lazy Susan (a circular disk mounted on a vertical axle) that has a radius 14.9 cm, rotational inertia 5.92 x 10-3 kg·m2, and frictionless bearings. The cockroach's speed (relative to the ground) is 2.92 m/s, and the lazy Susan turns clockwise with angular velocity ω0 = 3.89 rad/s. The cockroach finds a bread crumb on the rim and, of course, stops. (a) What is the angular speed of the lazy Susan after the cockroach stops? (b) Is mechanical energy conserved as it stops?
Answer:
-7.23 rad/s
Explanation:
Given that
Mass of the cockroach, m = 0.157 kg
Radius of the disk, r = 14.9 cm = 0.149 m
Rotational Inertia, I = 5.92*10^-3 kgm²
Speed of the cockroach, v = 2.92 m/s
Angular velocity of the rim, w = 3.89 rad/s
The initial angular momentum of rim is
Iw = 5.92*10^-3 * 3.89
Iw = 2.3*10^-2 kgm²/s
The initial angular momentum of cockroach about the axle of the disk is
L = -mvr
L = -0.157 * 2.92 * 0.149
L = -0.068 kgm²/s
This means that we can get the initial angular momentum of the system by summing both together
2.3*10^-2 + -0.068
L' = -0.045 kgm²/s
After the cockroach stops, the total inertia of the spinning disk is
I(f) = I + mr²
I(f) = 5.92*10^-3 + 0.157 * 0.149²
I(f) = 5.92*10^-3 + 3.49*10^-3
I(f) = 9.41*10^-3 kgm²
Final angular momentum of the disk is
L'' = I(f).w(f)
L''= 9.41*10^-3w(f)
Using the conservation of total angular momentum, we have
-0.068 = 9.41*10^-3w(f) + 0
w(f) = -0.068 / 9.41*10^-3
w(f) = -7.23 rad/s
Therefore, the speed of the lazy Susan after the cockroach stops is -7.23 and is directed in the opposite direction of the initial lazy Susan angular speed
b)
The mechanical energy of the cockroach is not converted as it stops
In order to get going fast, eagles will use a technique called stooping, in which they dive nearly straight down and tuck in their wings to reduce their surface area. While stooping, a 6- kg golden eagle can reach speeds of up to 53 m/s . While golden eagles are not very vocal, they sometimes make a weak, high-pitched sound. Suppose that while traveling at maximum speed, a golden eagle heads directly towards a pigeon while emitting a sound at 1.1 kHz. The emitted sound has a sound intensity level of 30 dB when heard at a distance of 5 m .A) Model this stooping golden eagle as an object moving at terminal velocity. The eagle’s drag coefficient is 0.5 and the density of air is 1.2 kg/m 3 . What is the effective cross-sectional area of the eagle’s body while stooping?B) What is the doppler-shifted frequency that the pigeon will hear coming from the eagle?C) Consider the moment when the pigeon is 5 m away from the eagle. At the pigeon’s position, what is the intensity (in W/m^2 ) of the sound the eagle makes?D) The golden eagle slams into the 250- g pigeon, which is initially moving at 10 m/s in the opposite direction (toward the eagle). The eagle grabs the pigeon in its talons, and they move off together in a perfectly inelastic collision. How fast do they move after the collision?
Answer:
Check the explanation
Explanation:
Part A
F = CA
this drag force balances the weight = 6X 9.8
so
6X9.8 = 0.5 X A X0.5 X 1.2 X 532
A= 0.069 m2
Part B
here the sorce is moving and the observer is at rest
so f= f(- 1 - 1
f = 1.1X10 343 343 – 53
f' = 1.3 KHz
Part C:
given the intensity = 30 dB
we know that I dB = 10 log (I(W/m2))
so we get I (W/m2) = 1000
Part D : The catch
Given that U1 = 53 M1 = 6 kg
U2 =-10 M2=0.25
V1=V2
now conserving momentum
6 X 53 -0.25 X10 =(6+0.25)V
V= 50.48 m/sec
plzzz help will mark the brainliest
Calculate potential energy of a 5 kg object sitting on 3 meter ledge
Answer:147 joules
Explanation:
Mass=m=5kg
Acceleration due to gravity=g=9.8m/s^2
Height=h=3 meter
Potential energy=m x g x h
Potential energy=5 x 9.8 x 3
Potential energy=147 joules
