What has a wind speed of 240 kph or greater?​

Answers

Answer 1

Answer:

SUPER TYPHOON (STY), a tropical cyclone with maximum wind speed exceeding 220 kph or more than 120 knots.


Related Questions

a concrete has a height of 5m and has unit area 3m² supports a mass of 30000kg.
Determine the stress, strain and change in height ​

Answers

Answer:

stress = 98000 N/m^2

strain = 3.92 x 10^-6

change in height = 0.0196 mm

Explanation:

Height, h = 5 m

Area, A = 3 m²

mass, m = 30000 kg

Stress is defined as the force per  unit area.

[tex]stress = \frac{mg}{A}\\\\stress = \frac{30000\times 9.8}{3}\\\\stress = 98000 N/m^2[/tex]

Young's modulus of concrete is Y = 2.5 x 10^10 N/m^2

Young's modulus is defined as the ratio of stress to the strain.

[tex]Y = \frac{stress}{strain}\\\\2.5\times 10^{10}= \frac{98000}{strain}\\\\strain = 3.92\times 10^{-6}[/tex]

let the change in height is h'.

Strain is defined as the ratio of change in height to the original height.

[tex]3.92\times 10^{-6} = \frac{h'}{5}\\\\h' = 1.96\times 10^{-5}m = 0.0196 mm[/tex]

When an automobile moves with constant velocity the power developed is used to overcome the frictional forces exerted by the air and the road. If the power developed in an engine is 50.0 hp, what total frictional force acts on the car at 55 mph (24.6 m/s)

Answers

P = F v

where P is power, F is the magnitude of force, and v is speed. So

50.0 hp = 37,280 W = F (24.6 m/s)

==>   F = (37,280 W) / (24.6 m/s) ≈ 1520 N

A small plane tows a glider at constant speed and altitude. If the plane does 2.00 * 105 J of work to tow the glider 145 m and the tension in the tow rope is 2560 N, what is the angle between the tow rope and the horizontal

Answers

Answer:

θ = 57.4°

Explanation:

The complete formula to find out the work done by the plane is as follows:

[tex]W = FdCos\theta[/tex]

where,

W = Work = 200000 J

F = Force = Tension = 2560 N

d = distance = 145 m

θ = angle between rope and horizontal = ?

Therefore,

[tex]200000\ J = (2560\ N)(145\ m)Cos\theta\\\\Cos\theta = \frac{200000\ J}{371200\ J}\\\\\theta = Cos^{-1}(0.539)[/tex]

θ = 57.4°

If the electron has half the speed needed to reach the negative plate, it will turn around and go towards the positive plate. What will its speed be, in meters per second, when it reaches the positive plate in this case

Answers

Answer:

 v = -v₀ / 2

Explanation:

For this exercise let's use kinematics relations.

Let's use the initial conditions to find the acceleration of the electron

            v² = v₀² - 2a y

when the initial velocity is vo it reaches just the negative plate so v = 0

           a = v₀² / 2y

now they tell us that the initial velocity is half

          v’² = v₀’² - 2 a y’

          v₀ ’= v₀ / 2

at the point where turn v = 0              

          0 = v₀² /4  - 2 a y '

          v₀² /4 = 2 (v₀² / 2y)  y’

          y = 4 y'

          y ’= y / 4

We can see that when the velocity is half, advance only ¼ of the distance between the plates, now let's calculate the velocity if it leaves this position with zero velocity.

         v² = v₀² -2a y’

         v² = 0 - 2 (v₀² / 2y) y / 4

         v² = -v₀² / 4

         v = -v₀ / 2

We can see that as the system has no friction, the arrival speed is the same as the exit speed, but with the opposite direction.

Define measurements.​

Answers

Answer:

act or process of measuring

Explanation:

Explanation:

the comparison of an unknown quantity with a known quantity.

~~~~~NEED HELP ASAP~~~~~
A point on a rotating wheel (thin loop) having a constant angular velocityy of 300 rev/min, the wheel has a radius of 1.5m and a mass of 30kg. (I = mr^2)


a.) Determine the linear regression

b.) At this given angular velocity, what is the rotational kinetic energy?

Answers

Answer:

Centripetal Acceleration 18.75 m/s^2, Rotational Kinetic Energy 843.75 J

Explanation:

a Linear acceleration (we cant find tangential acceleration with the givens so we will find centripetal)

a= ω^2*r

ω= 300rev/min

convert into rev/s

300/60= 5rev/s

a= 18.75m/s^2

b) use Krot= 1/2 Iω^2

plug in gives

1/2(30*2.25)(25)= 843.75 J

Test your prediction through calculation for the situations of the clay bob and the bouncy ball. Assume each has a mass of 100 grams, and each has an initial velocity of 20 m/s straight at the door. Ignore the effects of gravity. Calculate the change in momentum of

Answers

Answer:

a) Δp = -2.0 kgm / s,  b)   Δp = -4 kg m / s

Explanation:

In this exercise the change in moment of a ball is asked in two different cases

a) clay ball, in this case the ball sticks to the door and we have an inelastic collision where the final velocity of the ball is zero

         Δp = p_f - p₀

         Δp = 0 - m v₀

         Δp = - 0.100 20

         Δp = -2.0 kgm / s

b) in this case we have a bouncing ball, this is an elastic collision, as the gate is fixed it can be considered an object of infinite mass, therefore the final speed of the ball has the same modulus of the initial velocity, but address would count

         v_f = - v₀

        Δp = p_f -p₀

        Δp = m v_f - m v₀

        Δp = m (v_f -v₀)

        Δp = 0.100 (-20 - 20)

        Δp = -4 kg m / s

A long, straight, vertical wire carries a current upward. Due east of this wire, in what direction does the magnetic field point

Answers

The magnetic field of the wire will be directed towards west. Using right thumb rule one can get the direction of field lines.

The current in a conductor is 2.5A .explain the meaning of this statement

Answers

Answer:

In 1 second the amount of charge flowing through the conductor is 2.5 Q.

Explanation:

Action and reaction are equal in magnitude and opposite in direction.Then Why do not balance each other

Answers

Answer:

Action and reaction are equal in magnitude and opposite in direction but they do not balance each other because they act on different objects so they don't cancel each other out.

hope this will help you more

The following contribute to accidents when a teen driver has other teens as passengers

Answers

Answer:

When a teen driver drives with a lot of his peers as passengers they may lead to distraction which may later end up in accident as the driver was distracted

Overconfidence, lack of focus, and phone while driving are the factors  contribute to accidents when a teen driver controls other teens as passengers,

What are the factors contribute to accidents when a teen driver has other teens as passengers?

When a teen driver drives with a lot of his peers as passengers they may direct to distraction which may later end up in casualty as the driver was distracted.

Several studies have indicated that passengers substantially increase the chance of crashes for young, novice drivers. This improved risk may result from distractions that young passengers complete for drivers.Teens driving with a teen or young adult passengers existence of teen or young adult passengers raises the crash risk of unsupervised teen drivers. This risk grows with each additional teen or a young adult passenger.

Crash risk is two- to six times more significant for those who utilize a cellphone while driving resembled for drivers who are not distracted. Using a phone delays reaction time increases lane deviations, and forces drivers to look away from the road for extended times.

Overconfidence, lack of focus, and phone while driving are the factors  contribute to accidents when a teen driver controls other teens as passengers,

To learn more about factors contribute to accidents refer to:

https://brainly.com/question/4853141

#SPJ2

A uniformly charged thin rod of length L and positive charge Q lies along the x-axis with its left end at the origin as shown in Figure 1.

a. Set up a correct integral expression for the potential at point A,which lies a distance H above the right end of the rod. Point A has coordinates (L, H). You need to give appropriate limits of integration and expressions for r and dq

b. Set up a correct integral expression for the potential at point B on the x-axis, a distance D from the left end of the rod with the appropriate limits of integration.You need to give appropriate limits of integration and expressions for r and dq.

Answers

Answer:

b)

Explanation:

Name the electrolyte in the chemical method of generating electricity​

Answers

Some of such commonly used compounds are Sodium Chloride, Nitric Acid, Sulphuric Acid, Sodium Acetate, Chloric acid, etc. The first battery was invented by Italian physicist Alessandro Volta in the year 1799 by generating continuous electric current using voltaic piles.

why is unit of power is called derived unit?​

Answers

Distance travelled by a body in unit time is called speed. it is a scalar quantity because it can be specified only by magnitude.

TIME REMAINING
45:43
What are possible units for impulse? Check all that apply.

kg • m
kg • meters per second
N • s
N • m
StartFraction Newtons times meters per second EndFraction

Answers

Answer:

n.m maby

Explanation:

i think or its kg m/s

Answer:

answer (B) & (C)

Explanation:

kg • /N • s

Help me plssssssss cause I’m struggling

Answers

Answer:

I am pretty sure it is C

Explanation:

It can be found all over the universe

I think it’s c but I am not sure

In an exciting game, a baseball player manages to safely slide into second base. The mass of the baseball player is 88.9 kg and the coefficient of kinetic friction between the ground and the player is 0.53. (a) Find the magnitude of the frictional force in newtons. N (b) It takes the player 1.7 s to come to rest. What was his initial velocity (in m/s)

Answers

Answer:

Look at explanation

Explanation:

a) Kinetic Friction= μmg

μmg=0.53*88.9*9.8=461.75N

b)  -461.75N=ma

a= -5.19m/s^2

v=v0+at

5.19*1.7=v0

v0=8.81m/s^2

(a) The magnitude of the frictional force will be 461.75N

(b)The initial velocity will be 8.81 m/s.

What is kinetic friction?

A force that acts among sliding parts is referred to as kinetic friction. A body moving on the surface is subjected to a force that opposes its progressive motion

The size of the force will be determined by the kinetic friction coefficient between the two materials.

The given data in the problem is;

μ is the coefficient of kinetic friction= 0.53.

m is the mass = 88.9 kg

g is the acceleration due to gravity= 9.81 m/s²

v is the speed =?

The formula for friction force is;

[tex]\rm F= \mu R \\\\ R=mg \\\\ F= \mu mg \\\\\ F=0.53 \times 88.9 \times 9.81 \\\\ F= 461.75 \ N[/tex]

Mechanical force is found as;

F=ma

-461.75=(88.9)a

(-ve shows the -ve work done)

a=-5.19 m/s

From the Newton's first equation of motion;

v=u+at

0=u+at

u=-at

u=(- (-5.19)(1.7)

u=8.81 m/s²

To learn more about the kinetic friction refer to;

https://brainly.com/question/13754413

#SPJ2

why do you like the full moon ?

Answers

Answer:

The Moon brings perspective. Observing the Moon, and I mean really looking – sitting comfortably, or lying down on a patch of grass and letting her light fill your eyes, it's easy to be reminded of how ancient and everlasting the celestial bodies are. When I do this, it always puts my life into perspective.

Answer:

because it look more impressive than empty dark sky .

Mary and her younger brother Alex decide to ride the carousel at the State Fair. Mary sits on one of the horses in the outer section at a distance of 2.0 m from the center. Alex decides to play it safe and chooses to sit in the inner section at a distance of 1.1 m from the center. The carousel takes 5.8 s to make each complete revolution.

Required:
a. What is Mary's angular speed %u03C9M and tangential speed vM?
b. What is Alex's angular speed %u03C9A and tangential speed vA?

Answers

Answer:

you can measure by scale beacause we dont no sorry i cant help u but u can ask me some other Q

Four toy racecars are racing along a circular race track. The cars start at the 3-o'clock position and travel CCW along the track. Car A is constantly 2 feet from the center of the race track and travels at a constant speed. The angle Car A sweeps out increases at a constant rate of 1 radian per second.

Required:
How many radians θ does car A sweep out in t seconds?

Answers

Answer:

in t seconds, Car A sweep out t radian { i.e θ = t radian }

Explanation:

Given the data in the question;

4 toy racecars are racing along a circular race track.

They all start at 3 o'clock position and moved CCW

Car A is constantly 2 feet from the center of the race track and moves at a constant speed

so maximum distance from the center = 2 ft

The angle Car A sweeps out increases at a constant rate of 1 radian per second.

Rate of change of angle = dθ/dt = 1

Now,

since dθ/dt = 1

Hence θ = t + C

where C is the constant of integration

so at t = 0, θ = 0, the value of C will be 0.

Hence, θ = t radian

Therefore, in t seconds, Car A sweep out t radian { i.e θ = t radian }

The mass per unit length of the rope is 0.0500 kg/m. Find the tension. Express your answer in newtons.

Answers

Complete question:

A transverse wave on a rope is given by [tex]y \ (x, \ t) = (0.75 \ cm) \ cos \ \pi[(0.400 \ cm^{-1}) x + (250 \ s^{-1})t][/tex]. The mass per unit length of the rope is 0.0500 kg/m. Find the tension. Express your answer in newtons.

Answer:

The tension on the rope is 1.95 N

Explanation:

The general equation of a progressive wave is given as;

[tex]y \ (x,t) = A \ cos(kx \ + \omega t)[/tex]

Compare the given equation with the general equation of wave, the following parameters will be deduced.

A = 0.75 cm

k = 0.400π cm⁻¹

ω = 250π s⁻¹

The frequency of the wave is calculated as;

ω = 2πf

2πf = 250π

2f = 250

f = 250/2

f = 125 Hz

The wavelength of the wave is calculated as;

[tex]\lambda = \frac{2\pi}{k} \\\\\lambda = \frac{2\pi }{0.4 \pi} = 5 \ cm = 0.05 \ m[/tex]

The velocity of the wave is calculated as;

v = fλ

v = 125 x 0.05

v = 6.25 m/s

The tension on the rope is calculated as;

[tex]v = \sqrt{\frac{T}{\mu}} \\\\where;\\\\T \ is \ the \ tension \ of \ the \ rope\\\\\mu \ is \ the \ mass \ per \ unit \ length = 0.05 \ kg/m\\\\v^2 = \frac{T}{\mu} \\\\T = v^2 \mu\\\\T = (6.25)^2\times (0.05)\\\\T = 1.95 \ N[/tex]

Therefore, the tension on the rope is 1.95 N

A pilot flies her route in two straight-line segments. The displacement vector A for the first segment has a magnitude of 243 km and a direction 30.0o north of east. The displacement vector for the second segment has a magnitude of 178 km and a direction due west. The resultant displacement vector is R = A + B and makes an angle ? with the direction due east. Using the component method, find (a) the magnitude of R and (b) the directional angle ?.
(a) R = km
(b) ? = degrees

Answers

Answer:

a) [tex]R=126Km[/tex]

b) [tex]\theta=74.6\textdegree[/tex]

Explanation:

From the question we are told that:

1st segment

243km at Angle=30

2nd segment

178km West

Resolving to the X axis

[tex]F_x=243cos30+178[/tex]

[tex]F_x=33.44Km[/tex]

Resolving to the Y axis

[tex]F_y=243sin30+178sin0[/tex]

[tex]R=\sqrt{F_y^2+F_x^2}[/tex]

[tex]F_y=121.5Km[/tex]

Therefore

Generally the equation for Directional Angle is mathematically given by

[tex]\theta=tan^{-1}\frac{F_y}{F_x}[/tex]

[tex]\theta=tan^{-1}\frac{121.5}{33.44}[/tex]

[tex]\theta=74.6\textdegree[/tex]

Generally the equation for Magnitude is mathematically given by

[tex]R=\sqrt{F_y^2+F_x^2}[/tex]

[tex]R=\sqrt{33.44^2+121.5^2}[/tex]

[tex]R=126Km[/tex]

~~~~NEED HELP ASAP~~~~

Block A slides into block B along a frictionless surface. They are moving in the direction from left o the right.

Block A= 3kg

Block B= 4kg

Block A velocity before collision =30m/s.

Block B velocity before collision = 15 m/s

The velocity of block B after the collision is 20m/s.


a.) What is the velocity of block A after collision?

b.) Is the collision elastic? Show work to explain answer why or why not.

Answers

Answer:

Block A velocity is 23.33 m/s and the collission is not elastic.

Explanation:

a) m1v1 + m2v2 = m1v1' + m2v2'

Plug in givens

90+60=3v1'+80

solve for v1'= 23.33m/s

b) Find the initial and final kinetic energy of Block B

Ki= 1/2(4)(15)^2 + 1/2(3)(30)^2 = 1800 J

Kf= 1/2(4)(20)^2 + 1/2(3)*(23.33)^2= 1616.433J

Since Ki does not equal Kf the collision is not elastic

Pure water is an example of alan
A. Insulator
B. Metalloid
C. Conductor
D. Nonmetal

Answers

A. Insulator is the right answer

Answer: I think its A or C I'm not sure though sorry.

You are stranded in a stationary boat. Your friend is on a dock, but the boat is just beyond his reach. There is a 5 kg anchor in the boat. You'd like to get the boat to move closer to the dock so your friend can rescue you. Select from the following list what effect each change will have on the position of the boat relative to the dock. A. The boat will move closer to the dock. B. The boat will move away from the dock. C. The position of the boat relative to the dock will not change.

Answers

Answer:

running away and launching the anchor that will give a greater speed towards the dock v₄.

Explanation:

To try to bring the boat closer to the dock, several cases can be carried out.

* move inside the ship so that the center of mass changes and since moving away you have a speed v, the ship will approach the dock at a speed v₂,

* Throw the anchor in the opposite direction to the dock so that using the conservation of the moment the boat moves towards it, it moves at a speed v₃

* A combination of the two processes running away and launching the anchor that will give a greater speed towards the dock v₄.

In all cases, the friction must be zero.

All other movements move the ship away from the dock

1.Lõi thép máy biến áp được ghép từcác lá thép là để:

(a) Giảm tổn hao công suất do dòng điện xoáy

(b) Giảm tổn hao công suất do từ trễ

(c) Giảm tổn hao công suất do dòng điện chạy qua dây quấn

(d) Giảm tất cảcác loại tổn hao công suất.

Answers

Answer:

Option (c)

Explanation:

1.The transformer core is assembled from steel sheets to:

(a) Reduced power loss due to eddy current

(b) Reduced power loss due to hysteresis

(c) Reduced power loss due to current flowing through the winding

(d) Reduce all types of power loss.

A transformer is a device which converts the low voltage into high and vice  versa.

There are two types of a transformer.

Step up: It is used to convert low voltage into high.

Step down It is used to convert high voltage into high.

It depends on the number of turns in primary and the secondary coil.

The core of the transformer is laminated and it is in the form of sheets.

By using such type of core, the power loss due to the windings is reduced.

option (c) .

A 10 kg box is at static equilibrium and the downward pull of gravity acting on the box is 98 Newton’s what is the minimum force that would require to just pick up the box

Answers

Explanation:

static equilibrium means its on the floor or something

so slightly greater than 98 newtons in the upward direction

What best describes a societal law

Answers

Answer:

Societal laws are based on the behavior and conduct made by society or government.

hope it helps.stay safe healthy and happy.

The period of a pendulum is the time it takes the pendulum to swing back and forth once. If the only dimensional quantities that the period depends on are the acceleration of gravity, g, and the length of the pendulum, l, what combination of g and l must the period be proportional to

Answers

Explanation:

Let T is the period of a pendulum. The SI unit of time is seconds (s).

It depends on the acceleration of gravity, g, and the length of the pendulum, l.

The SI unit of acceleration of gravity, g and the length of the pendulum, l are m/s² and m respectively.

If we divide m and m/s², we left with s². If the square root of s² is taken, we get s only i.e. the SI unit of period of a pendulum.

So,

[tex]T\propto \sqrt{\dfrac{l}{g}}[/tex]

Hence, this is the required solution.

Two substances, M and N, have specific heats c and 2c. if heats Q and 4Q are supɔlied to Mand N, respectively, their changes in temperature become equal. If substance M has mass m, find the mass of substance N in terms of m

Answers

Answer:

If the mass of B is m and the temperature change is the same, the mass of B will be 2m.

Explanation:

Q = mcT

T = mc/Q

M = 4Q/2cT........... (1)

T = Q/mc

Plug this in equation 1.

M = 4Q/(2c × Q/mc)  = 4Q ÷ 2Q/m  = 4Q × m/2Q = 2m

Other Questions
Which of the following is NOT a type of biological weathering?A. Carbon dioxide dissolving into clouds and forming acid rain.B. Animals digging burrows.C. Lichen absorbing minerals from stone.D. Plants growing roots into concrete.Hurry!! .- Qu diferencias encuentran entre bailar siguiendo el ritmo de la msica y bailar reproduciendo una secuencia de movimientos? Let America be America again Which statement best expresses how the author develops thesecond speaker's point of view?A The second speaker agrees with the first speaker but wantseveryone in America to be happy and free.B The second speaker questions the first speaker and explainsthat there are lots of people who are treated unfairly inAmerica.C The second speaker builds on what the first speakerdescribes as America becoming a place again whereeveryone is happy and free.D The second speaker disagrees with the first speaker andexplains the history of those people who have been treatedunfairly in America. The most common Class II variant is the F508del variant, which is missing the 508th amino acid in the protein but has an otherwise normal sequence. Loss of this amino acid leads to misfolding of the protein, and the misfolded protein is not properly transported to the membrane. Based on this information, how many nucleotides are deleted in the CFTR allele encoding this variant? how did militarism in europe threaten peace on the continent A gas is put into a cosed container.The container and the gas inside it are heated.What will happen to the pressure inside the container? The wavelike muscular squeezing of the esophagus, stomach, and small intestine that pushes their contents along is called _____. chewing Solve by factorisation.3x + 10x - 8 = 0 Managerial implications for the SDT theory include: Group of answer choices to motivate high performance for uninteresting jobs make performance contingent on extrinsic rewards. All of these. to motivate high performance for uninteresting jobs make performance contingent on intrinsic rewards. focus on the hygiene factors in order to reduce dissatisfaction and increase intrinsic motivation to enhance intrinsic motivation for interesting jobs be sure individuals receive large pay bonuses for high achievement GIVING BRAINLIEST!! Which of the following ordered pairs lies on the graph of y = tanx?(5 pi, 0)(-9pi/4, 1) WILL GIVE BRAINLIST!Directions: Answer each of the questions below. Answer each question in paragraph form using complete sentences, proper capitalization, and punctuation.A. Evaluate the presidency of Andrew Jackson. Do you think that his actions were considered normal during his time?B. Analyze racism towards Native Americans during this period.C. Identify and describe at least two (2) positive events during this period. Tell why you believe these events were positive and whether these events were influenced by Jackson's presidency. if you subtract 1/2 from a number and multiply the result by 1/2 you get 1/8. What is the no. simplify (x^a.x^b)^a-b*(x^b.x^c)^b-c*(x^c.x^a)^c-astep by step.. translate They will know into spanish by filling in the missing letters You have to find the value of k A ball is dropped from a roof of a building and strikes the ground in 3 seconds. If a second ball is thrown horizontally from the roof, it will hit the ground in: An example of fast tracking a project schedule would be to overlap the design and production phases for a design-to-production project, where the conventional approach would be to move on to construction only after completing the design phase.a. Trueb. False How do I answer 3 and 4 An airplane with a ground speed of 550 km/hr travels along a heading of 30 degrees n of w at that high altitude there is a powerful 210 km/hr wind