What is the chemical formula for the molecule modeled?

Answer:

Z

Explanation:

correct on edge

Answer: Z

good luck!

Answer:

A. 3.9 V B. 1.9 fA

Explanation:

Part A

What emf is induced in the ring as the field changes?

Express your answer to two significant figures and include the appropriate units.

The induced emf ε = ΔΦ/Δt where ΔΦ = change in magnetic flux = ΔABcosθ where A = area of coil and B = magnetic field strength, θ = angle between A and B = 0 (since the axis of the ring is parallel )Δt = change in time

ε = ΔΦ/Δt

ε = ΔABcos0°/Δt

ε = AΔB/Δt

A = πd²/4 where d = diameter of ring = 2.0 cm = 2.0 × 10⁻² m, A = π(2.0 × 10⁻² m)²/4 = π4.0 × 10⁻⁴ m²/4 = 3.142 × 10⁻⁴ m², ΔB = change in magnetic field strength = B₁ - B₀ where B₁ = final magnetic field strength = 2.5 T and B₀ = initial magnetic field strength = 0 T.  ΔB = B₁ - B₀  = 2.5 T -0 T = 2.5 T and Δt = 200 μs = 200 × 10⁻⁶ s.

So, ε = AΔB/Δt

ε = 3.142 × 10⁻⁴ m² × 2.5 T/200 × 10⁻⁶ s

ε = 7.854 × 10⁻⁴ m²-T/2 × 10⁻⁴ s

ε = 3.926 V

ε ≅ 3.9 V

Part B

If the band is gold with a cross-section area of 4.0 mm2, what is the induced current? Assume the band is of jeweler's gold and its resistivity is 13.2 x 1010 Ω*m.

Express your answer to two significant figures and include the appropriate units.

Since current, i = ε/R where ε = induced emf = 3.926 V and R = resistance of band = ρl/A where ρ = resistivity of band = 13.2 × 10¹⁰ Ωm, l = length of band = πd where d = diameter of band = 2.0 cm = 2.0 × 10⁻² m. So, l = π2.0 × 10⁻² m = 6.283 × 10⁻² m and A = cross-sectional area of band = 4.0 mm² = 4.0 × 10⁻⁶ m².

So, i =  ε/R

=  ε/ρl/A

= εA/ρl

= 3.926 V × 4.0 × 10⁻⁶ m²/(13.2 × 10¹⁰ Ωm × 6.283 × 10⁻² m)

= ‭15.704‬ × 10⁻⁶ V-m²/(82.9356‬ × 10⁸ Ωm²

= 0.1894 × 10⁻¹⁴ A

= 1.894 × 10⁻¹⁵ A

≅ 1.9 fA

Answer:

Force = 5.22 N

Explanation:

According to Newton's Second Law of motion:

[tex]Force = Rate\ of\ Change\ of\ Momentum\\\\Force = \frac{mv_f-mv_i}{t}\\[/tex]

where,

m = mass of ball = 145 g = 0.145 kg

vf = final speed of ball after hit = 25 m/s

vi = initial speed of ball before hit = -  11 m/s (negative sign due to opposite direction)

t = time of contact = 1 s

Therefore,

[tex]Force = \frac{(0.145\ kg)(25\ m/s)-(0.145\ kg)(-11\ m/s)}{1\ s} \\\\[/tex]

Force = 5.22 N

Answer:

the ratio of her final kinetic energy to her initial kinetic energy is 1.7.

Explanation:

Given;

initial angular speed, ω₁ = 5.9 rad/s

let her initial moment of inertia = I₁

her final moment of inertia [tex]I_2 = \frac{I_1}{1.7}[/tex]

Apply the principle of conservation of angular momentum to determine the final angular speed of the girl;

[tex]\omega_1I_1 = \omega_f I_2\\\\\omega_f = \frac{\omega _1 I_1}{I_2} \\\\\omega_f = \frac{5.9 \times I_1}{I_1/1.7} \\\\\omega = 5.9 \times 1.7 \\\\\omega_f = 10.03 \ rad/s[/tex]

The initial rotational kinetic energy is given as;

[tex]K.E_I = \frac{1}{2}I_1 \omega_I ^2[/tex]

The final rotational kinetic energy is given as;

[tex]K.E_f = \frac{1}{2}I_2 \omega_f ^2[/tex]

The ratio of her final kinetic energy to her initial kinetic energy is given as;

[tex]\frac{K.E_f}{K.E_I}= \frac{\frac{1}{2}I_2 \omega_f^2 }{\frac{1}{2} I_1\omega _1^2} \\\\\frac{K.E_f}{K.E_I}= \frac{I_2 \omega_f^2}{ I_1\omega _1^2} \\\\\frac{K.E_f}{K.E_I}= \frac{I_1/1.7 \times \omega_f^2}{ I_1 \times \omega _1^2} \\\\\frac{K.E_f}{K.E_I}= \frac{ \omega_f^2}{ 1.7 \omega _1^2} \\\\\frac{K.E_f}{K.E_I}= \frac{ (10.03)^2}{ 1.7(5.9)^2} = \frac{17}{10} = 1.7[/tex]

Therefore, the ratio of her final kinetic energy to her initial kinetic energy is 1.7.

Answer:

use the formula to calculate acceleration and you'll get the answers

Answer: 84 %

Explanation:

Answer:

Surface tension is,  the surface where the water meets the air, water molecules cling even more tightly to each other.

Answer:

b

Explanation:

f1=-f2 that could be thank u

Answer:

[tex]p =-1.03[/tex]

Explanation:

From the question we are told that:

Focal length of lens [tex]f=-0.304 m[/tex]

Image distance [tex]q=0.237 m[/tex]

Height of image [tex]H_i=0.343[/tex]  

Generally the lens equation is mathematically given by

[tex]\frac{1}{f} = \frac{1}{q} - \frac{1}{p}[/tex]

Where [tex]p[/tex] is Subject

[tex]p = \frac{(qf) }{(f - q)}[/tex]

[tex]p = \frac{(-0.237)(-0.304)) }{((-0.304) - (0.237))}[/tex]

[tex]p =-1.03[/tex]

Therefore the distance between  the person and the car is

[tex]p =-1.03[/tex]

Answer:

i dont know but i should know try g o o g l e

Explanation:

Answer:

Explanation:

The kinetic energy of block will be converted into potential energy of spring .

If A be the amplitude of oscillations

1 /2 k A² = 1/2 m v²

17 A² = 1.1 x .46²

A² = .0137

A= 11.7 cm

B )

when x = .25 A = .25 x 11.7 = 2.9 cm

potential energy = 1/2 k x²

= .5 x 17 x ( .029 )² = .00715 J

kinetic energy = 1/2 m v²

1/2 m v²  +  .00715  = .5 1.1 x .46²

1/2 m v²  +  .00715  = .1164

1/2 m v² = .10925

.5 x 1.1 x v²=  .10925

v² = .1986

v = .4456 m /s

= 44.56 cm /s

This question is incomplete, the complete question is;

A particle is directed along the axis of the instrument in the figure below. A parallel plate capacitor sets up an electric field E, which is oriented perpendicular to a uniform magnetic field B. If the plates are separated by d = 2.0 mm and the value of the magnetic field is B = 0.60T.

Calculate the potential difference, between the capacitor plates, required to allow a particle with speed v = 5.0 × 10⁵ m/s to pass straight through without deflection.

Hint : ΔV = Ed

Answer:

the required potential difference, between the capacitor plates is 600 V

Explanation:

Given the data in the question;

B = 0.60 T

d = 2.0 mm = 0.002 m

v = 5.0 × 10⁵ m/s.

since particle pass straight through without deflection.

F[tex]_{net[/tex] = 0

so, F[tex]_E[/tex] = F[tex]_B[/tex]

qE = qvB

divide both sides by q

E = vB

we substitute

E = (5.0 × 10⁵) × 0.6

E = 300000 N/C

given that; potential difference ΔV = Ed

we substitute

ΔV = 300000 × 0.002

ΔV = 600 V

Therefore, the required potential difference, between the capacitor plates is 600 V

hydroelectric dam converts the potential energy stored in a water reservoir behind a dam to mechanical energy—mechanical energy is also known as kinetic energy. ... The generator converts the turbine's mechanical energy into electricity.

Hope this helps!

Answer:

Potential energy and kinetic energy are constituents of mechanical energy.

When a turbine is switched on, it rotates with mechanical energy.

Since a motor runs the turbine, it converts this mechanical energy to electrical energy.

Answer:

a. Speed = 1.6 m/s

b. Amplitude = 0.3 m

c. Speed = 1.6 m/s

Amplitude = 0.15 m

Explanation:

a.

The frequency of the wave must be equal to the reciprocal of the time taken by the boat to move from the highest point to the highest point again. This time will be twice the value of the time taken to travel from the highest point to the lowest point:

frequency = [tex]\frac{1}{2(2\ s)}[/tex] = 0.25 Hz

The wavelength of the wave is the distance between consecutive crests of wave. Therefore,

Wavelength = 6.4 m

Now, the speed of the wave is given as:

Speed = (Frequency)(Wavelength)

Speed = (0.25 Hz)(6.4 m)

Speed = 1.6 m/s

b.

Amplitude is the distance between the mean position of the wave and the extreme position. Hence, it will be half the distance between the highest and lowest point:

Amplitude = (0.5)(0.6 m)

Amplitude = 0.3 m

c.

frequency = [tex]\frac{1}{2(2\ s)}[/tex] = 0.25 Hz

Speed = (Frequency)(Wavelength)

Speed = (0.25 Hz)(6.4 m)

Speed = 1.6 m/s

Amplitude = (0.5)(0.3 m)

Amplitude = 0.15 m

Answer:

Potential energy

Explanation:

Potential energy is stored energy

Answer:

It is because of the tilt of the earth.

Explanation:

the earth is tilted at 23.5 degrees. this makes it so that either the northern or southern hemisphere will be exposed to more rays from the sun. In the areas that are getting more rays from the sun, it gets warmer.  Think about it like this, because the earth is tilted, part of it is more in the shade and part of it is more in the light. And its colder in the shade, so thats why seasons happen and why they dont happen at the same time.

Answer:

C

Explanation:

Primacy means being first or important so thats not an important facial display as the others.

Answer:blue

Explanation:

I read it

Answer:

24 J

Explanation:

[tex]K = \frac{1}{2} mv^{2} = \frac{1}{2} (3kg)(4m/s)^{2} = 24 J[/tex]

Answer:

θ = cos^(-1) (-A/B)

Explanation:

The image of the reauktant forces A & B are missing, so i have attached it.

Now, from the attached image, we will see that;

Angle between A and B is θ

Also;

A = Bcos(180° − θ)

Now, in trigonometry, we know that;

cos(180° − θ) = -cosθ

Thus;

A = -Bcosθ

cosθ = -A/B

Thus;

θ = cos^(-1) (-A/B)

C.

Explanation:

C. is a gamma ray and they carry the most energy.

The most energy is carried by the gamma rays. The correct option is C.

Gamma radiation, also known as gamma rays, is a type of electromagnetic radiation produced by the radioactive decay of atomic nuclei. It is made up of electromagnetic waves with the shortest wavelengths, which are typically shorter than those of X-rays.

Waves with a higher frequency have more energy. Gamma rays have the shortest wavelengths and highest frequencies of any electromagnetic wave. Gamma rays have more energy than any other electromagnetic wave due to their extremely high frequencies.

To know more about gamma rays follow

https://brainly.com/question/22166705

#SPJ6

The average temperature of the air in the room at 20 min is 23°C.

Temperature is the degree of hotness or coldness of the object.

A student heated 235 g of water in a beaker until the water reached 100°C. The student removed the beaker from the heat and placed the beaker on a counter in a 23°C room. The student recorded the temperature of the water every 4 minutes for 20 minutes.

The surrounding is vast, its temperature does not get affected by small amount of water. So, the temperature of air remains constant.

Thus, the average temperature of the air in the room at 20 min is 23°C.

Learn more about temperature.

https://brainly.com/question/11464844

#SPJ2

Answer:

a) 10.51 J

b) 3.48 m/s

Explanation:

Given data :

mass of train ( M ) = 2.2 kg

Given initial velocity ( u ) = 1.6 m/s

a) calculating work done by the force over the journey of the train

F = mx + b  ------ ( 1 )

m = slope  = ( Δ f / Δ x ) = 2.8 / -7.5 = - 0.373 N/m

x = distance travelled on the x axis by the train = 7.5 m

F = force experienced by the train = 2.8 N

x = 0

∴ b = 2.8

hence equation 1 can be written as

F = ( -0.373) x + 2.8   ----- ( 2 )

hence to determine the work done by the force

W   = [tex]\int\limits^7_0 { ( -0.373) x + 2.8 )} \, dx[/tex]     Note:  the limits are actually 7.5 and 0

∴ W ( work done ) = -10.49 + 21 = 10.51 J

b) calculate the speed of the train at the end of its journey

we will apply the work energy theorem

W = 1/2 m*v^2  -  1/2 m*u^2

∴ V^2 = 2 / M ( W + 1/2 M*u^2 )  ( input values into equation )

 V^2 = 12.11

hence V = 3.48 m/s

Answer:

Truck [tex]\dfrac{g}{10}[/tex]

Road [tex]-\dfrac{g}{10}[/tex]

Explanation:

[tex]a_1[/tex] = Acceleration of truck = [tex]-\dfrac{g}{2}[/tex]

[tex]\mu[/tex] = Coefficient of friction = [tex]\dfrac{2}{5}[/tex]

Frictional force is given by

[tex]f=-\mu mg\\\Rightarrow f=-\dfrac{2}{5}mg\\\Rightarrow ma_2=-\dfrac{2}{5}mg\\\Rightarrow a_2=-\dfrac{2}{5}g[/tex]

Net acceleration is given by

[tex]a=a_2-a_1\\\Rightarrow a=-\dfrac{2}{5}g+\dfrac{g}{2}\\\Rightarrow a=\dfrac{g}{10}[/tex]

The acceleration of the box relative to the truck is [tex]\dfrac{g}{10}[/tex] and [tex]-\dfrac{g}{10}[/tex] relative to the road.

Answer: C

Explanation:

USAtestprep

Answer:

Amplitude

Explanation:

The loudness of a sound depends on the amplitude of vibration producing the sound

Answer:

[tex]10.54\ \text{rad/s}[/tex]

Explanation:

[tex]\omega_i[/tex] = Initial angular velocity = 500 rpm = [tex]500\times \dfrac{2\pi}{60}\ \text{rad/s}[/tex]

[tex]\omega_f[/tex] = Final angular velocity

t = Time = 34 s

[tex]\theta[/tex] = Angular displacement = 170 revs = [tex]170\times 2\pi\ \text{rad}[/tex]

[tex]\alpha[/tex] = Angulr acceleration

From the kinematic equations of angular motion we have

[tex]\theta=\omega_it+\dfrac{1}{2}\alpha t^2\\\Rightarrow \alpha=\dfrac{\theta-\omega_it}{\dfrac{1}{2}t^2}\\\Rightarrow \alpha=\dfrac{170\times 2\pi-500\times \dfrac{2\pi}{60}\times 34}{\dfrac{1}{2}\times 34^2}\\\Rightarrow \alpha=-1.23\ \text{rad/s}^2[/tex]

[tex]\omega_f=\omega_i+\alpha t\\\Rightarrow \omega_f=500\times \dfrac{2\pi}{60}+(-1.23)\times 34\\\Rightarrow \omega_f=10.54\ \text{rad/s}[/tex]

The rate at which the wheel is spinning when the power comes back on is [tex]10.54\ \text{rad/s}[/tex].