What is the major difference between herbal and conventional medicines

Answers

Answer 1
Most importantly, the main difference between herbal medicines and conventional medicines is that herbal medicines each contain a combination of chemicals, as opposed to a single pharmacologically active substance.

Related Questions

A steam engine takes in superheated steam at 270 °C and discharges condensed steam from its cylinder at 50 °C. The engine has an efficiency of 30%, and taken in 50 kJ from the hot steam per cycle. If a Carnot engine takes in the same amount of heat per cycle and operates at these temperatures, the work it can turn into is most likely to be:a) 15 kJ. b) 20 kJ. c) 10 kJ. d) 50 kJ.

Answers

Answer:

b) 20 kJ

Explanation:

Efficiency of carnot engine = (T₁ - T₂ ) / T₁  Where T₁ is temperature of hot source  and T₂ is temperature of sink .

T₁ = 270 + 273 = 543K

T₂ = 50 + 273 = 323 K

Putting the given values of temperatures

efficiency = (543 - 323) / 543

= .405

heat input = 50 KJ

efficiency = output work / input heat energy

.405 = output work / 50

output work = 20.25 KJ.

= 20 KJ .

6. The two ends of an iron rod are maintained at different temperatures. The amount of heat thatflows through the rod by conduction during a given time interval does notdepend uponA) the length of the iron rod.B) the thermal conductivity of iron.C) the temperature difference between the ends of the rod.D) the mass of the iron rod.E) the duration of the time interval.Ans: DDifficulty: MediumSectionDef: Section 13-27. The ends of a cylindrical steel rod are maintained at two different temperatures. The rod conducts heat from one end to the other at a rate of 10 cal/s. At what rate would a steel rod twiceas long and twice the diameter conduct heat between the same two temperatures

Answers

Answer:

20cal/s

Explanation:

Question:

There are two questions. The first one has been answered:

From the formular, Power = Q/t = (kA∆T)/l

the amount heat depends on the duration of time interval, length of the iron rod, the thermal conductivity of iron and the temperature difference between the ends of the rod.

The amount of heat that flows through the rod by conduction during a given time interval does not depend upon the mass of the iron rod (D).

Second question:

The ends of a cylindrical steel rod are maintained at two different temperatures. The rod conducts heat from one end to the other at a rate of 10 cal/s. At what rate would a steel rod twice as long and twice the diameter conduct heat between the same two temperatures?

Solution:

Power = 10cal/s

Power = energy per unit time = Q/t

Where Q = energy

Power = (kA∆T)/l

k = thermal conductivity of iron

A = area

Area = πr^2

r = radius

Diameter = d = 2r

r = d/2

Area = (πd^2)/4

Length = l

∆T = change in temperature

10 = (kA∆T)/l

For a steel rod with length doubled and diameter doubled:

Let Length (L) = 2l

Diameter (D)= 2d

Area = π [(2d)^2]/4 = (π4d^2)/4

Area = 4(πd^2)/4

Using the formula Power = (kA∆T)/l, insert the new values for A and l

Power = [k × 4(πd^2)/4 × ∆T]/2l

Power = [4k((πd^2)/4) ∆T]/2l

Power = [(4/2)×k((πd^2)/4) ∆T]/l

Power = [2k(A) ×∆T]/l = 2(kA∆T)/l

Power of a steel that has its length doubled and diameter doubled = 2(kA∆T)/l

Recall initial Power = (kA∆T)/l = 10cal/s

And ∆T is the same

2[(kA∆T)/l] = 2 × 10

Power of a steel that has its length doubled and diameter doubled = 20cal/s

A particle is projected at an angle 60 degrees to the horizontal with a speed of 20m/s. (i) calculate total time of flight of the particle. (i) speed of the particle at its maximum height

Answers

Answer:

Time of flight=3.5 seconds

Speed at maximum height is 0

Explanation:

Φ=60°

initial velocity=u=20m/s

Acceleration due to gravity=g=9.8 m/s^2

Total time of flight=T

Final speed=v

question 1:

T=(2 x u x sinΦ)/g

T=(2 x 20 x sin60)/9.8

T=(2 x 20 x 0.8660)/9.8

T=34.64/9.8

T=3.5 seconds

Question 2

Speed at maximum height is 0

PIUDICITIS CONSECulvely and Circle your aliswers. Lilyo
proper significant digits.
53. When you turn on your CD player, the turntable accelerates from zero to 41.8 rad/s in
3.0 s. What is the angular acceleration?
or​

Answers

Answer:

The angular acceleration of CD player is [tex]13.93\ rad/s^2[/tex].

Explanation:

Initial angular speed of a CD player is 0 and final angular speed is 41.8 rad/s. Time to change the angular speed is 3 s.

It is required to find the angular acceleration. The change in angular speed of the CD player divided by time taken is called its angular acceleration. It can be given by :

[tex]a=\dfrac{\omega_f-\omega_i}{t}\\\\a=\dfrac{41.8-0}{3}\\\\a=13.94\ rad/s^2[/tex]

So, the angular acceleration of CD player is [tex]13.93\ rad/s^2[/tex].

Vocabulary Matching
The specialized equipment used to conduct research and repair
damaged equipment
Instruments
Space Station
Space Suit
Accomodations

Answers

Answer:

instruments

Explanation:

Which term BEST describes the movement of air from the ocean toward the land in the daytime? (AKS 4b DOK 1) *
1 point
Sea breeze
Land Breeze
Valley Breeze
Current Breeze

Answers

Answer:

Option A, Sea Breeze

Explanation:

Ssea breeze is a wind that blows from the ocean or any water body to the nearby land mass. This breeze is cold as compared to the air on land. The water in water bodies has high specific heat capacity and hence takes longer time to cool as compared to the surrounding objects. The warmer air over the land rises upward thereby reducing the pressure on land and hence the sea breeze starts flowing from region of high pressure (i.e above the water body) towards the low pressure region that is the land.

Hence, option A is correct

A 0.009 kg bullet fired through a door enters at 803 m/s and leaves at 617 m/s. If the door material is known to exert an average resistive force of 5620 N on bullets of this type at usual speeds, find the thickness of the door.

Answers

Answer:

The thickness of the door is 0.4230 m

Explanation:

Given;

mass of bullet, m = 0.009 kg

initial velocity of the bullet, u = 803 m/s

final velocity of the bullet, v = 617 m/s

average resistive force of the door on the bullet, F = 5620 N

Apply Newton's second law of motion;

Force exerted by the door on the bullet = Force of the moving bullet

F = ma

where;

F is applied force

m is mass

a is acceleration

Also, Force exerted by the door on the bullet = Force of the moving bullet

[tex]F =ma, \ But \ a =\frac{dv}{dt} = \frac{u-v}{t} \\\\F = \frac{m(u-v)}{t}[/tex]

where;

v is the final velocity of the bullet

u is initial velocity of the bullet

t is time

We need to calculate the time spent by the bullet before it passes through the door.

[tex]t = \frac{m(u-v)}{F} \\\\t = \frac{0.009(803-617)}{5620} = 0.0002979 \ s[/tex]

Distance traveled by the bullet within this time period = thickness of the door

This distance is equivalent to the product of average velocity and time

[tex]S = (\frac{u+v}{2}) t[/tex]

where;

s is the distance traveled

[tex]S = (\frac{u+v}{2}) t\\\\S = (\frac{803+617}{2}) 0.0002979\\\\S = 0.4230 \ m[/tex]

Therefore, the thickness of the door is 0.4230 m

If you apply a force of 130 N to the lever, how much force is applied to lift the
crate?

Answers

Answer:171 N

Explanation:

Answer:

171 N.

Explanation:

Arm OA rotates counterclockwise with a constant angular velocity of ω = 5 rad/s. As the arm passes the horizontal position, a 6 kg ball is placed at the end of the arm. As the arm moves upward, the ball begins to roll, with negligible rolling resistance, towards the pivot O. It is noted that at θ = 30 ◦ , the ball is 0.9 meters from the pivot and moving towards O along the length of the arm. The ball moves with a speed of 0.4 m/s along the bar. What is the normal force that the arm applies to the ball at this instant? Please, indicate which principle you are applying and explain why.

Answers

Answer:

26.92 N

Explanation:

The normal reaction of the ball is due to two force component acting on it.

The normal reaction as a result of the weight of the  ballThe normal reaction due to the component of the acceleration of the ball with the rod.

However ; the acceleration is in polar coordinate which is given by the relation:

[tex]a^ { ^ \to} = (r- r \omega^2) \hat {e_r} + ( r \theta + 2 r \omega ) \hat {e_ \theta}[/tex]

[tex]a_{\theta} = r \theta + 2 r \omega[/tex]

Given that :

ω = 5 rad/s

mass m = 6 kg

θ = 30 ◦

r = 0.9 m

speed v =  0.4 m/s

[tex]a_{\theta} = 0 + 2(-0.4)*5[/tex]

[tex]a_{\theta}= -4 \ m/s[/tex]

The normal force reaction (N) that the arm applies to the ball at this instant is :

N = mg cos θ  + [tex]ma_{\theta}[/tex]

N = (6 × 9.8× cos 30) + (6 ×(-4))

N = 26.92 N

A light bulb dissipates 100 Watts of power when it is supplied a voltage of 220 volts.
a) What is the current flowing through this light bulb?
b) What is the resistance of the light bulb?

Answers

Given Information:

Power = P = 100 Watts

Voltage = V = 220 Volts

Required Information:

a) Current = I = ?

b) Resistance = R = ?

Answer:

a) Current = I = 0.4545 A

b) Resistance = R = 484 Ω

Explanation:

According to the Ohm’s law, the power dissipated in the light bulb is given by

[tex]P = VI[/tex]

Where V is the voltage across the light bulb, I is the current flowing through the light bulb and P is the power dissipated in the light bulb.

Re-arranging the above equation for current I yields,

[tex]I = \frac{P}{V} \\\\I = \frac{100}{220} \\\\I = 0.4545 \: A \\\\[/tex]

Therefore, 0.4545 A current is flowing through the light bulb.

According to the Ohm’s law, the voltage across the light bulb is given by

[tex]V = IR[/tex]

Where V is the voltage across the light bulb, I is the current flowing through the light bulb and R is the resistance of the light bulb.

Re-arranging the above equation for resistance R yields,

[tex]R = \frac{V}{I} \\\\R = \frac{220}{0.4545} \\\\R = 484 \: \Omega[/tex]

Therefore, the resistance of the bulb is 484 Ω

Answer:

bulb will burn out!

Explanation:

A. A PH202 student lives next to a construction site and sees a crane with a wrecking ball demolish the building next door. The wrecking ball swings along the wall between her house and the neighbor’s house. In an effort to determine the length of the cable on the wrecking ball the student builds a pendulum using a random rock and a string. Her pendulum turns out to be 0.500m long. While she plays with her pendulum she realizes that the wrecking ball swings back and forth in the same amount of time that it takes the rock to complete 5 full oscillations. What is the length of the cable on the wrecking ball?

Answers

Answer:

The length of cable is 12.5 m

Explanation:

Since, the wrecking ball completes 1 oscillation, in the same time, as it takes for the rock to complete 5 oscillations.

Therefore,

Time Period of Wrecking Ball = 5 (Time Period of Rock)

Since,

Time Period of  Pendulum = 2π√(L/g)

Therefore,

2π√(L₁/g) = 5[2π√(L₂/g)]

√L₁ = 5√L₂

Squaring on both sides:

L₁ = 25 L₂

where,

L₁ = Length of Cable = ?

L₂ = Length of string = 0.5 m

Therefore,

L₁ = 25 (0.5 m)

L₁ = 12.5 m

A resistor and a capacitor are connected in series across an ideal battery having a constant voltage across its terminals. Long after contact is made with the battery (a) the voltage across the capacitor is A) equal to the battery's terminal voltage. B) less than the battery's terminal voltage, but greater than zero. C) zero. (b) the voltage across the resistor is A) equal to the battery's terminal voltage. B) less than the battery's terminal voltage, but greater than zero. C) zero.

Answers

Answer:

A) equal to the battery's terminal voltage.

Explanation:

When the capacitor is fully charged after long hours of charging , its  potential becomes equal to the emf of the battery and its polarity is opposite to that of battery . Hence net emf becomes equal . The capacitor itself becomes a battery which is connected in the circuit with opposite polarity . This results in the net emf and  current becoming zero . There is no charging current when the capacitor is fully charged .

An astronaut visiting Jupiter's satellite Europa leaves a canister of 1.20 mol of nitrogen gas (28.0 g/mol) at 50.0 ∘C on the satellite's surface. Europa has no significant atmosphere, and the acceleration due to gravity at its surface is 1.30 m/s2. The canister springs a leak, allowing molecules to escape from a small hole. Neglect the interaction with surrounding atmosphere. (a) What is the maximum height (in km) above Europa's surface that is reached by a nitrogen molecule whose speed equals the rms speed? Assume that the molecule is shot straight up out of the hole in the canister, and ignore the variation in g with altitude. (b) The escape speed from Europa is 2025 m/s. Can any of the nitrogen molecules escape from Europa and into space?

Answers

Answer:

the answer is a

Explanation:

Time Warner Cable's leadership development program that spanned over 30 days and included weekly videos, practice exercises, and a two hour webinar was discussed in the Sed as an example of which of the following?
a) tracking training through a leaming records store LRS)
b) using big data to analyze training compliance
c) using gamification to enhance learning
d) an application of advances in neuroscience to training

Answers

Answer: A.

tracking training through a leaming records store LRS.

Explanation:

An LRS uses xAPI to collect learner data, or experiences, from both online and offline sources. These experiences are reported back to the LRS in the form of xAPI statements, where they are stored. These statements can then be retrieved for reporting and interpretation of the learner data.

A long solid conducting cylinder with radius a = 12 cm carries current I1 = 5 A going into the page. This current is distributed uniformly over the cross section of the cylinder. A cylindrical shell with radius b = 21 cm is concentric with the solid cylinder and carries a current I2 = 3 A coming out of the page. 1)Calculate the y component of the magnetic field By at point P, which lies on the x axis a distance r = 41 cm from the center of the cylinders.

Answers

Answer:

Explanation:

We shall use Ampere's circuital law to find magnetic field at required point.

The point is outside the circumference of two given wires so whole current will be accounted for .

Ampere's circuital law

B = ∫ Bdl = μ₀ I

line integral will be over circular path of radius r = 41 cm .

Total current  I  = 5A -3A = 2A .

∫ Bdl = μ₀ I

2π r B = μ₀ I

2π x .41  B = 4π x 10⁻⁷ x 2

B = 2 x 10⁻⁷ x 2 / .41

= 9.75 x 10⁻⁷ T . It will be along - ve Y - direction.

A student performs an experiment that involves the motion of a pendulum. The student attaches one end of a string to an object of mass M and secures the other end of the string so that the object is at rest as it hangs from the string. When the student raises the object to a height above its lowest point and releases it from rest, the object undergoes simple harmonic motion. As the student collects data about the time it takes for the pendulum to undergo one oscillation, the student observes that the time for one swing significantly changes after each oscillation. The student wants to conduct the experiment a second time. Which two of the following procedures should the student consider when conducting the second experiment?
a) Make sure that the length of the string is not too long.
b) Make sure that the mass of the pendulum is not too large.
c) Make sure that the difference in height between the pendulum's release position and rest position is not too large.
d) Make sure that the experiment is conducted in an environment that has minimal wind resistance.

Answers

Answer:

the answers the correct one is cη

Explanation:

In this simple pendulum experiment the student observes a significant change in time between each period. This occurs since an approximation used is that the sine of the angle is small, so

              sin θ = θ

 

with this approach the equation will be surveyed

     d² θ / dt² = - g / L sin θ

It is reduced to

      d² θ / dt² = - g / L θ

in which the time for each oscillation is constant, for this approximation the angle must be less than 10º so that the difference between the sine and the angles is less than 1%

The angle is related to the height of the pendulum

         sin θ = h / L

         h = L sin θ.

Therefore the student must be careful that the height is small.

When reviewing the answers the correct one is cη

Considering the approximation of simple harmonic motion, the correct option is:

(c) Make sure that the difference in height between the pendulum's release position and rest position is not too large.

Simple Harmonic Motion

According to Newton's second law in case of rotational motion, we have;

[tex]\tau = I \alpha[/tex]

Applying this, in the case of a simple pendulum, we get;

[tex]-mg\,sin\,\theta =mL^2 \,\frac{d^2 \theta}{dt^2}[/tex]

On, rearranging the above equation, we get;

[tex]mL^2 \,\frac{d^2 \theta}{dt^2} + mg\,sin\,\theta=0\\\\\implies \frac{d^2 \theta}{dt^2} +\frac{g}{L} sin \,\theta=0[/tex]

Now, if angular displacement is very small, i.e.; the bob of the pendulum is only raised slightly.

Then, [tex]sin\, \theta \approx \theta[/tex]

[tex]\implies \frac{d^2 \theta}{dt^2} +\frac{g}{L} \,\theta=0[/tex]

This is now in the form of the equation of a simple harmonic motion.

[tex]\frac{d^2 \theta}{dt^2} +\omega^2 \,\theta=0[/tex]

Comparing both these equations, we can say that;

[tex]\omega = \sqrt{\frac{g}{L}}[/tex]

[tex]T=2\pi\sqrt{\frac{L}{g}}[/tex]

This relation for the time period can only be obtained if the angular displacement is very less.

So, the correct option is;

Option (c): Make sure that the difference in height between the pendulum's release position and rest position is not too large.

Learn more about simple harmonic motion here:

https://brainly.com/question/26114128

Block A, with a mass of 4 kg, is moving with a speed of 2 m/s while Block B, with a mass of 8.4 kg, is moving in the opposite direction with a speed of 6.1 m/s. The center of mass of the two block system is moving with a velocity of ____ m/s. Round your answer to the nearest tenth. Assume Block A is moving in the positive direction.

Answers

Answer:

The center of mass move with the velocity of -3.487 m/s.

Explanation:

Given values of block A.

Mass of block A, (M1) = 4 kg

Speed of block A, (V1) = 2 m/s

Given values of block B.

 Mass of block B, (M2) = 8.4 kg

Speed of block B, (V2) = -6.1 m/s

Below is the formula to find the velocity of center of mass.

[tex]Velocity = \frac{M1V1 + M2V2}{M1 + M2} \\[/tex]

[tex]= \frac{4 \times 2 + 8.4 \times (-6.1) }{4 + 8.4} \\[/tex]

[tex]= \frac{- 43.24}{12.4}\\[/tex]

[tex]= - 3.487 m/s[/tex]

Consider a circular vertical loop-the-loop on a roller coaster. A car coasts without power around the loop. Determine the difference between the normal force exerted by the car on a passenger with a mass of mm at the top of the loop and the normal force exerted by the car on her at the bottom of the loop. Express your answer in terms of mmm and the acceleration due to gravity ggg.

Answers

Answer:

Explanation:

Let v₁ and v₂ be velocities at lowest and topmost position . Let r be the radius of the circle .

Let N₁ and N₂ be the normal reaction force .

At the top position

centripetal force = N₂ + mg ;  so

N₂ + mg  = m v₂² / r

At the bottom  position

centripetal force = N₁ - mg ;  so

N₁ - mg  = m v₁² / r

subtracting these two equations

N₁ - mg - N₂ - mg = m v₁² / r  - m v₂² / r

N₁ - N₂ - 2mg = 1/r (m v₁²   - m v₂²  )

N₁ - N₂ - 2mg = 1/r x mg x 2r  ( loss of potential energy = gain of kinetic energy )

N₁ - N₂ =  2mg +  2mg

= 4 mg .

A Texas cockroach of mass 0.157 kg runs counterclockwise around the rim of a lazy Susan (a circular disk mounted on a vertical axle) that has a radius 14.9 cm, rotational inertia 5.92 x 10-3 kg·m2, and frictionless bearings. The cockroach's speed (relative to the ground) is 2.92 m/s, and the lazy Susan turns clockwise with angular velocity ω0 = 3.89 rad/s. The cockroach finds a bread crumb on the rim and, of course, stops. (a) What is the angular speed of the lazy Susan after the cockroach stops? (b) Is mechanical energy conserved as it stops?

Answers

Answer:

-7.23 rad/s

Explanation:

Given that

Mass of the cockroach, m = 0.157 kg

Radius of the disk, r = 14.9 cm = 0.149 m

Rotational Inertia, I = 5.92*10^-3 kgm²

Speed of the cockroach, v = 2.92 m/s

Angular velocity of the rim, w = 3.89 rad/s

The initial angular momentum of rim is

Iw = 5.92*10^-3 * 3.89

Iw = 2.3*10^-2 kgm²/s

The initial angular momentum of cockroach about the axle of the disk is

L = -mvr

L = -0.157 * 2.92 * 0.149

L = -0.068 kgm²/s

This means that we can get the initial angular momentum of the system by summing both together

2.3*10^-2 + -0.068

L' = -0.045 kgm²/s

After the cockroach stops, the total inertia of the spinning disk is

I(f) = I + mr²

I(f) = 5.92*10^-3 + 0.157 * 0.149²

I(f) = 5.92*10^-3 + 3.49*10^-3

I(f) = 9.41*10^-3 kgm²

Final angular momentum of the disk is

L'' = I(f).w(f)

L''= 9.41*10^-3w(f)

Using the conservation of total angular momentum, we have

-0.068 = 9.41*10^-3w(f) + 0

w(f) = -0.068 / 9.41*10^-3

w(f) = -7.23 rad/s

Therefore, the speed of the lazy Susan after the cockroach stops is -7.23 and is directed in the opposite direction of the initial lazy Susan angular speed

b)

The mechanical energy of the cockroach is not converted as it stops

water is pumped from a stream at the rate of 90kg every 30s and sprayed into a farm at a velocity of 15m/s. Calculate the power of the pump.​

Answers

Answer:

340 W

Explanation:

Power = change in energy / change in time

P = ΔKE / Δt

P = ½ mv² / Δt

P = ½ (90 kg) (15 m/s)² / (30 s)

P = 337.5 W

Rounded to 2 significant figures, the power is 340 W.

What do you think will be different about cars in the future? Describe a change that is already being developed or that you think should be invented.

Answers

Answer:

Flying cars.

Explanation:

what do hydroelectric plants use to generate electrical energy?

Answers

Answer:

A.  falling water

Explanation:

I got it right on Edgenuity. Good luck on your quiz.

In hydroelectric plants, water falls on turbine and makes it rotate. In generator, this mechanical energy transforms into electrical energy.

What is hydroelectric power?

Hydroelectric power is generated by turbines that turn the potential energy of falling or swiftly flowing water into mechanical energy, which is then used to power generators. The most popular renewable energy source in the early 21st century was hydroelectricity, which in 2019 accounted for more than 18% of the world's total power producing capacity.

Water is gathered or stored at a higher elevation during the production of hydroelectric power and then transported through substantial pipes or tunnels (penstocks) to a lower elevation; the difference between these two elevations is referred to as the head. The falling water turns turbines as it nears the bottom of the pipelines. In turn, the turbines power generators, which transfer the mechanical energy of the turbines into electricity.

Learn more about  hydroelectric power here:

https://brainly.com/question/15228003

#SPJ2

3. The current in a flashlight powered by 4.5 Volts is 0.5 A. What is the power delivered to the flashlight?
4.If the flashlight in the previous problem is left on for 3 minutes, how much electric energy is delivered to the bulb?

Answers

Answer:

Question 3: 2.25 watts

Question 4: 405 joules

Explanation:

question 3:

Current =0.5 amps

Voltage =4.5 volts

Power= current x voltage

Power=0.5 x 4.5

power=2.25 watts

Question 4

Current =0.5 amps

Voltage =4.5v

Time=3 minutes

Time =3x60

Time =180 seconds

Energy=current x voltage x time

Energy =0.5 x 4.5 x 180

Energy =405 joules

Which is the correct representation of the right-hand rule for a current flowing to the right?

Answers

Answer:

The third image

Explanation:

The one with the thumb pointing to the right

Answer:

3, correct on Edge 2020

If Jim could drive a Jetson's flying car at a constant speed of 440 km/hr across oceans and space, approximately how long (in millions of years, in 106 years) would he take to drive to a nearby star that is 12.0 light-years away? Use 9.461 × 1012 km/light-year and 8766 hours per year (365.25 days).

Answers

Answer:

t = 2.94 x 10⁶ years

Explanation:

The equation used in the case of constant speed is:

s = vt

t = s/v

where,

s = distance = 12 light years

s = (12 light years)(9.461 x 10¹² km/light year) =  113.532 x 10¹² km

v = speed = 440 km/hr

t = time passed = ?

Therefore,

t = (113.532 x 10¹² km)/(440 km/hr)

t = 2.58 x 10¹¹ hr

Now, converting it to years:

t = (2.58 x 10¹¹ hr)(1 year/8766 hr)

t = 2.94 x 10⁶ years

8. At temperature 15°C, aluminum rivets have a diameter of 0.501 cm, and holes drilled in a titanium sheet have a diameter of 0.500 cm. If both the aluminum rivets and the titanium sheet are cooled together, at what temperature will the rivets just fit into the appropriate holes in the titanium sheet? Use 25x10-6 (°C)-1 for the coefficient of linear expansion for aluminum, and 8.5x10-6 (°C)-1 for titanium

Answers

Answer:

The temperature is [tex]T = -106 ^oC[/tex]

Explanation:

From the question we are told that

   The temperature is [tex]T_1 = T_t= T_a=15^oC[/tex]

   The  diameter is  [tex]d_1 = 0.5001 cm[/tex]

    The diameter of the hole [tex]d_2 = 0.500 \ cm[/tex]

    The coefficient of linear expansion for aluminum is [tex]\alpha _1 = 25 *10^{-6} \ ^oC^{-1}[/tex]

    The coefficient of linear expansion for  titanium is [tex]\alpha _2 = 8.5 *10^{-6} \ ^o C^{-1}[/tex]

According to the law of linear expansion

     [tex]d = d_o (1 + \alpha \Delta T )[/tex]

Where [tex]d_o[/tex] represents the original diameter

  So for aluminum

          [tex]d_a = d_1 (1 + \alpha_1 (T- T_a) )[/tex]

Where [tex]d_a[/tex] is the new diameter of aluminum

          [tex]T_a[/tex] is the new temperature of the aluminum

So for titanium

      [tex]d_t = d_2 (1 + \alpha_1 (T- T_t) )[/tex]

Where [tex]d_t[/tex] is the new diameter of  titanium

          [tex]T_t[/tex] is the new temperature of the aluminum

So for the aluminum rivets to fit into the holes

     [tex]d_a = d_t[/tex]

=>  [tex]d_1 (1 + \alpha_1 (T- T_a) ) = d_2 (1 + \alpha_2 (T- T_t) )[/tex]

       Making T the subject of the formula

     [tex]T = \frac{(d_1 - d_2 ) + (d_2 *\alpha_2 T_t) - d_1 \alpha_1 * T_a }{d_2 \alpha_2 - d_1 \alpha_1 }[/tex]

    Substituting values

     [tex]T = \frac{(0.501 - 0.500 ) + (0.500 *(8.5*10^{-6}) * 15) - 0.500* (25*10^{-6}) * 15 }{0.500 * (8.5 *10^{-6}) - 0.501 * (25 *10^{-6}) }[/tex]

    [tex]T = -106 ^oC[/tex]

What must x be so that the handle end of the bat remains at rest as the bat begins to move? (Hint: Consider the motion of the center of mass and the rotation about the center of mass. Find x so that these two motions combine to give v=0 for the end of the bat just after the collision. Also, note that integration of equation ∑τ⃗ =dL⃗ dt gives ΔL=∫t1t2(∑τ)dt. )

Answers

Complete Question

The complete question is shown on the first uploaded image

Answer:

Explanation:

From the question we are told that

     The mass of the bat is [tex]m_b = 0.800 \ kg[/tex]

      The bat length is  [tex]L_b = 0.900 \ m[/tex]

      The distance of the bat's center of mass to the handle end is  [tex]z_c = 0.600 \ m[/tex]

      The moment of inertia of the bat is    [tex]I = 0.0530 \ kg \cdot m^2[/tex]

The objective of the solution is to find  x   which is the distance from the handle of the bat to the point where the baseball hit the bat

Generally the velocity change at the end of the bat is mathematically represented as

         [tex]\Delta v_e = \Delta v_c - \Delta w* z_c[/tex]

         Where  [tex]\Delta v_c[/tex] is the velocity change at the center of the bat  which is mathematically represented as

                [tex]\Delta v_c = \frac{Impulse}{m_b }[/tex]

We are told that the impulse is  J so

              [tex]\Delta v_c = \frac{J}{m_b }[/tex]

And   [tex]\Delta w[/tex] is the change in angular velocity which is mathematically represented as

         [tex]\Delta w = \frac{J (z -z_c)}{I}[/tex]

Now we have that

           [tex]\Delta v_e = \frac{J}{m_b } - [\frac{J (x- z_c)}{I} ] * z_c[/tex]

Before a swing when the bat is at rest the velocity change a the end of the bat handle is zero  and the impulse will be  1

   So  

            [tex]0 = \frac{1}{m_b } - [\frac{J (x- z_c)}{I} ] * z_c[/tex]

=>           [tex]x = \frac{I}{m_b z_c} + m_b[/tex]

substituting values

            [tex]x = \frac{0.530}{0.800 * 0.600} + 0.600[/tex]

           [tex]x = 0.710 \ m[/tex]

                     

Electric fields are MOST associated with ________.

Answers

With each point in space

The greater the distance between two objects in space, the _______ their gravitational

Answers

Answer is Weaker. If it is talking about the objects' gravitational forces.

Calculate potential energy of a 5 kg object sitting on 3 meter ledge

Answers

Pe=5*9.8*3=147 joules

Answer:147 joules

Explanation:

Mass=m=5kg

Acceleration due to gravity=g=9.8m/s^2

Height=h=3 meter

Potential energy=m x g x h

Potential energy=5 x 9.8 x 3

Potential energy=147 joules

Other Questions
Which plant or plant part is a source of edible oils?A.wheatB.kidney beansC.sunflowerD.riceE.cottonseed Amy must choose a number between 55 and 101 that is a multiple of 3, 6, and 7. Write all the numbers that she could choose. If there is more than one number, separate them with commas. Do contact lenses do damage to your eyes? What energy transformations take place in Joule's system? Hawk-Dove (or Chicken) (t = tough, c = concede) Two (young) players are engaged in a conflict situation. For instance, they may be racing their cars towards each other on Main Street, while being egged on by their many friends. If player 1 hangs tough and stays in the center of the road while the other player concedeschickens outby moving out of the way, then all glory is his and the other player eats humble pie. If they both hang tough they end up with broken bones, while if they both concede they have their bodiesbut not their prideintact. Player 1 \ Player 2 t c t -1,-1 10,0 c 0, 10 5, 5 The matrix form can be used to compactly represent the strategic form when there are two players even if each player has more than two strategies to choose from. The shock from an electric fence would be the least unpleasant if you werestandingA. on dry, thick gravelB. in tall grassC. In wet grassOD. near the livestock What happens to light energy that is not absorbed by an object What happens to light energy that is not absorbed by an object Meiji leaders did all of the following excepta.instituted a constitutional monarchyc.modernized the army and navyb.introduced communism as the new social systemd.opened schoolsPlease select the best answer from the choices providedABCD The hourly wages earned by 20 employees are shown in the first box-and-whisker plot below. The person earning $15 per hour quits and is replaced with a person earning $8 per hour. The graph of the resulting salaries is shown in plot 2. A box-and-whisker plot is shown. The number line goes from 7 to 15. The whiskers range from 8 to 15, and the box ranges from 8.8 to 10.2. A line divides the box at 9.5. Plot 1 A box-and-whisker plot is shown. The number line goes from 7 to 15. The whiskers range from 8 to 11, and the box ranges from 8.7 to 10. A line divides the box at 9.6. Plot 2 How does the mean and median change from plot 1 to plot 2? The mean and median remain the same. The mean decreases, and the median remains the same. The mean remains the same, and the median decreases. The mean and median decrease. pls help (ASASP)This is the simplest invertebrate animal. Most are asymmetrical and reproduce either through asexual means or through internal, self-fertilization because most are hermaphrodites. During cellular respiration, which of the following is equal to the total number of carbon, hydrogen, and oxygen atoms in water and carbon dioxide? Number of carbon, hydrogen, and oxygen atoms in glucose Number of carbon, hydrogen, and oxygen atoms in oxygen gas Total number of carbon, hydrogen, and oxygen atoms in glucose and oxygen Total number of carbon, hydrogen, and oxygen atoms in hydrogen gas and oxygen Mark is 4 years older than his brother Mike. If the sum of their ages is 20 how old are they now? NEED HELP ASAPFind the volume of the cylinder. r measures 7 inches, height measures 8 inches Mason bought a rotisserie in preparation for a party he was planning. When he put a chicken on the rotisserie, it would not rotate, but stayed in one position where it burned the chicken on one side a left it raw on the other. Does Mason have any recourse? Predict the likely effect on the ability of substance L to enter the cells if substance L is attached to a large protein instead of free in theculture. Suppose you had toguess on a four-choicemultiple-choice test andwere given four questions.Find the binomialprobability distribution.( + ) =4 = 0.25 Which ordered par Woud form a proportional relationship with the point graphed Below? A (10,10) B (25,35) C (70,50) D (90,60) In an ecosystem1. living things interact with each other2. living things interact with their environment3. both of the above Choose the sentence with the correct punctuation.A. There are four parts to a plant; roots, stem, leaves, and flower.B. You need to do three chores: vacuum the front room, fold the laundry, and make your bed.C. Dear Mr. Carter;D. I love reading all types of books; mystery, horror, suspense, and biographies. Dr. Fletcher took a deep breath before she opened theenvelope. The letter was from Enrique, whom she had notheard from in two years. "My dearest doctor," the letterbegan. "Where do I begin? As you know, we met under thepalms of the Nile on a steamboat called the EmeraldMessenger, at a card table to be exact. I believe the gamewas bridge. Do you remember? That night, I gave you apackage, which I hope you haven't opened. You kept askingme what was in the package, and I kept avoiding thequestion. Well, it is time you knew."Which part of the story is from the frame narrative?