Answer:
Explanation: A compound with the empirical formula SO has a molecular weight of 96.13
During a dry compression test, the first puff of the test shows 50 PSI and the maximum reading after 4 strokes is 150 PSI. This indicates A. that the cylinders are good. B. weak piston rings. C. a bad spark plug. D. a hole in the piston.
One of the basic engine-diagnostic procedures that can be run is an engine compression test. All of the cylinders must have the same compression for the engine to run smoothly. There are just three possible ways for air to leak out of an engine and cause compression loss.
Exhaust or intake valve Engine rings (or piston, if there is a hole) An engine's head gasketThe procedures for conducting a compression testThe engine should be warmed to its typical operating temperature before testing in order to achieve the best results. The following procedures should be followed for an accurate compression test:
STEP 1: Dispose of each spark plug. As a result, the engine can be turned up to the same speed. Label all spark plug wires accurately.STEP 2 is to block the throttle open. This enables the engine to pull in the most air possible. Additionally, this step guarantees reliable compression test results.STEP 3 After inserting a compression gauge into a spark plug hole, start the engine. Four compression strokes of engine cranking should be performed in total. A puffing sound is produced after each compression stroke.EXAMPLE-If the ultimate, maximum value is 150 PSI, for instance, the reading following the first puff should be greater than 75 PSI. Low first-puff readings could be a sign of weak piston rings.STEP 4 Keep track of the highest readings, then compare the outcomes.Learn more about compression test here https://brainly.com/question/13274092
#SPJ2
In order to determine the answer to a chemistry problem, a student first converted the given percentages to mole by assuming the sample size was 100 grams. Then the student divide by the smallest mole amount of the elements present. Finally the student used the ratios to write a formula. Which of the following best describes the problem the student likely solved?
a. Determined percent composition
b. None of the above
c. Determining molecular formula
d. Determining empirical formula
Answer: d. Determining empirical formula
Explanation:
Molecular formula is the chemical formula which depicts the actual number of atoms of each element present in the compound.
Empirical formula is the simplest chemical formula which depicts the whole number of atoms of each element present in the compound.
Step 1: If percentage are given then we are taking total mass is 100 grams. So, the mass of each element is equal to the percentage given.
Step 2 : convert given masses into moles
Step 3 : For the mole ratio, divide each value of moles by the smallest number of moles calculated
Step 4: The mole ratio gives the empirical formula of the compund.
Please help I have no idea where to start
Answer:
Download Ptable, it will show all of the elements, and you can click on them, and it will show all the information you need about them!
Explanation:
I hope this helps!!!!!
You have three containers each of which is connected to a fourth empty container. Three of the containers contain pure gases. In the first container oxygen is at 2 atm, nitrogen at 4 atm is in the second container, and argon at 1 atm is in the third. When you open the valve and mix the gases in the forth container, what is the pressure, PT, in the forth container
Answer: The total pressure is 7 atm
Explanation:
According to Dalton's law, the total pressure is the sum of individual pressures.
[tex]p_{total}=p_A+p_B+p_C...[/tex]
Given : [tex]p_{total}[/tex] =total pressure of gases = ?
[tex]p_{O_2}[/tex] = partial pressure of oxygen = 2 atm
[tex]p_{N_2}[/tex] = partial pressure of nitrogen = 4 atm
[tex]p_{Ar}[/tex] = partial pressure of argon = 1 atm
putting in the values we get:
[tex]p_{total}=2atm+4atm+1atm[/tex]
[tex]p_{total}=7atm[/tex]
Thus the total pressure is 7 atm
Equal masses of aluminum and copper are heated to 100 degree C and placed in water. Which would cause the water to reach the higher temperature? Explain your answer.
Answer:
copper will reach to higher temperature first.
Explanation:
Calculate the [H+] concentration for a solution with a pH of 6.4
*☆*――*☆*――*☆*――*☆*――*☆*――*☆*――*☆*――*☆**☆*――*☆*――*☆*――*☆
Answer: 3.98 x 10^-7
Explanation:
I hope this helped!
<!> Brainliest is appreciated! <!>
- Zack Slocum
*☆*――*☆*――*☆*――*☆*――*☆*――*☆*――*☆*――*☆**☆*――*☆*――*☆*――*☆
1L = 1000 mL
Molarity (M) = moles of solute / L of solution
Calculate the moles of NaCl required to prepare 250 mL of 1.5 M aqueous solution.
Answer:· 44 g NaCl Explanation: The problem provides you with the molarity and volume of the target
Explanation:
help people i really need this
True or false silicon is a nonmetal
Answer:
True , Silicon is a nonmetal
5.07 x 10^24 atoms of antimony is how many moles?
8.98 mol
7.99 mol
4.82 mol
8.42 mol
Answer:
8.42 moles (3 sig. figs.)
Explanation:
Given 5.07 x 10²⁴ atoms of antimony (Sb) => ? moles Sb
1 mole of any substance contains 6.02 x 10²³ particles ( atoms or molecules)
∴ Think in terms of 'how many 6.02 x 10²³'s are in 5.07 x 10²⁴ atoms Sb?
That is => moles Sb = 5.07 x 10²⁴ atoms Sb / 6.02 x 10²³ atoms Sb/mole Sb
= 8.42192691 moles Sb (calculator answer) ≅ 8.42 moles (3 sig. figs.)
Boyle's Law states that when a sample of gas is compressed at a constant temperature, the pressure P and volume V satisfy the equation PV = C, where C is a constant. Suppose that at a certain instant the volume is 300 cm3, the pressure is 180 kPa, and the pressure is increasing at a rate of 30 kPa/min. At what rate is the volume decreasing at this instant?
Answer:
The gas is decreasing at a rate of 50 cubic centimeters per minute.
Explanation:
The Boyle's Law is represented by the following expression:
[tex]P\cdot V = k[/tex] (1)
Where:
[tex]P[/tex] - Pressure, in kilopascals.
[tex]V[/tex] - Volume, in cubic centimeters.
[tex]k[/tex] - Proportionality constant, in kilopascal-cubic centimeters.
By definitions of rate of change and implicit differentiation, we derive the following differential equation:
[tex]\dot P \cdot V + P\cdot \dot V = 0[/tex] (2)
Where:
[tex]\dot P[/tex] - Rate of change of the pressure, in kilopascals per minute.
[tex]\dot V[/tex] - Rate of change of the volume, in cubic centimeters per minute.
Then, we clear the rate of change of the volume within (2):
[tex]P\cdot \dot V = -\dot P\cdot V[/tex]
[tex]\dot V = -\left(\frac{\dot P}{P} \right) \cdot V[/tex]
If we know that [tex]P = 180\,kPa[/tex], [tex]\dot P = 30\,\frac{kPa}{min}[/tex] and [tex]V = 300\,cm^{3}[/tex], then the rate of change of the volume is:
[tex]\dot V = -\left(\frac{\dot P}{P} \right) \cdot V[/tex]
[tex]\dot V = -50\,\frac{cm^{3}}{min}[/tex]
The gas is decreasing at a rate of 50 cubic centimeters per minute.
Ethanol in the body is oxidized to acetaldehyde by liver alcohol dehydrogenase (LADH). Other alcohols are also oxidized by LADH. For example, methanol, which is mildly intoxicating, is oxidized by LADH to the quite toxic product of formaldehyde. The toxic effects of ingesting methanol (a component of many commercial solvents) can be reduced by administering ethanol. The ethanol acts as a competitive inhibitor of methanol by displacing it from LADH. This provides sufficient time for the methanol to be harmlessly excreted by the kidneys. If an individual has ingested 30 mL of methanol (a lethal dose), how much 100 proof whiskey (50% ethanol by volume) must be imbibed to reduce the activity of her LADH towards methanol to 5% of its original value? The adult human body contains ~40L of aqueous fluids throughout which ingested alcohols are rapidly and uniformly mixed. The densities of ethanol and methanol are both 0.79 g/cm3. Assume the KM values of LADH for ethanol and methanol to be 10-3 M and 10-2 M, respectively, and that Ki = KM for ethanol
Answer: The changes are the mL of methanol ingestion (30mL) and the proof of the whiskey (40% ethanol; 80 proof), and the percentage of reduction (1%). I applied the formulas from the last post in reference to this question but am completely lost. The formulas used last time were: 2. Formulas Applied alpha=1 + ([etOH]/KetOH) (V[meOH]/V[etOH])= (Vmax*[meOH]/KmeOH+[meOH])/(Vmax*[meOH]/alpha*KmeOH+[meOH]) which reduces to (V[meOH]/V[etOH])=(alpha*KmeOH+[meOH])/(KmeOH+[meOH]) 3. My attempt Molarity of methanol: 30mL; which equates to 23.7g of methanol; in 40L that is equal to 0.5925 g/L Dividing the molecular weight by 32.04g/mol I get 0.0184925 which is approximately 0.02M; Km is 0.01M Since the molar mass of methanol and ethanol are two fold, I can multiply the g/l by 4. However, unlike the previous problem, I cannot multiply by 2 because I do not have 50% EtOH, so because 40 is less than 50 I assume to multiply by 2.5 yielding: (30mL)(4)(2.5)=300mL 300mL of EtOH to effectively reduce the Methanol to 1%.
what happens when ?? Fresh red flower is introduced into a vessel contain Sulphur dioxide along
with moisture.
what climate is Colorado in?
A.Most Subtropical Mid-Latitude
B.Polar
C.Moist ContinentaMid-Latitiude
D.Dry
Answer:
b
Explanation:
Answer:
D. Dry
Explanation:
Colorado's combination of high elevation, midlatitude, and continental interior geography results in a cool, dry climate.
how proved that carbon is present in sugar?
In all living organisms, in substances like carbohydrate, starch, urea etc. To prove sugar contains carbon, take a little amount of sugar in spoon and heat it gently till it melts and turned into yellowish color. On further heating it changes into brown colored mass and then black, which is charcoal.
Answer: sugar treated with strong sulphur acid turns to black
Explanation: sulphur acid removes water from sugars and carbon is left in residue.
This should not to try at home. Water boils when high temperature is achieved.
Also smell of burned sugar occurs
Choose the best answer
1. Gas A diffuses twice as fast as another gas B. If the density of the gas A is 2, the molecular mass of
(a)2
(b) 4
(c) 8
(d) 16
i think it is
(b) 4
:) hope its correct :)
What is 2AI(s) + FeO3(s) = Ai2O3(s) + 2Fe(s)
Answer:
it's a double displacement Reaction.
Predict the product of this reaction
Al(s) + N2(g)—->
Which compound is more soluble in water at 25°C?
A.
MgF2 (Ksp = 5.2 x 10-11)
B.
SrF2 (Ksp = 7.9 x 10-10)
C.
AgBr (Ksp = 5.0 x 10-13)
D.
Agl (Ksp = 1.5 * 10-16)
Answer:
B
Explanation:
The solubility depends on the ksp. As the value of ksp increases the compound becomes more and more soluble.
In the options, the highest ksp value is 10^-10, thus that one is the most soluble.
The mass of a salt in grams that will dissolve in 100 mL of water.
____________ A solution that has dissolved the maximum amount of a compound at a given temperature. Any further addition of salt will remain undissolved.
_________ The product of the molarities of the dissolved ions, raised to a power equal to the ion's coefficient in the balanced chemical equation.
__________ A decrease in the solubility of an ionic compound as a result of the addition of a common ion.
__________ The maximum number of moles of a salt that will dissolve in 1 L of solution.
a. A decrease in the solubility of an ionic compound as a result of the addition of a common ion.
b. The mass of a salt in grams that will dissolve in 100 mL of water.
c. A solution that has dissolved the maximum amount of a compound at a given temperature. Any further addition of salt will remain undissolved.
d. The product of the molarities of the dissolved ions, raised to a power equal to the ion's coefficient in the balanced chemical equation.
e. The maximum number of moles of a salt that will dissolve in 1 L of solution.
Answer:
Solubility : The mass of a salt in grams that will dissolve in 100 mL of water
Saturated solution : A solution that has dissolved the maximum amount of a compound at a given temperature. Any further addition of salt will remain undissolved
Solubility product constant :The product of the molarities of the dissolved ions, raised to a power equal to the ion's coefficient in the balanced chemical equation
Common ion effect : A decrease in the solubility of an ionic compound as a result of the addition of a common ion
Molar solubility : The maximum number of moles of a salt that will dissolve in 1 L of solution
Explanation:
Solubility is expressed usually as the mass of solute per 100 grams or 100 ml of solvent.
Molar solubility of a solid is expressed as the concentration of the dissolved solid in a saturated solution.
Solubility product constant is defined as the equilibrium constant in which a solid ionic compound is dissolved to produce its ions in solution. It is represented as
The common-ion effect is the decrease in solubility of a sparingly soluble salt by the addition to the solution of a soluble compound with an ion in common with the precipitate.
Saturated solution is defined as the solution in which no more solute particles can be dissolved in the solvent.
can u identify a chemical equation for the saponification of olive oil as per your experiment?
I
im not sure if it is a molecule or an atom
Answer:
the first one
Explanation:
I looked it up:P
Only the 2nd answer is right, uncheck the 1st one
Explanation:
If we had a chemical formula like [tex]3(O_{2} )[/tex] the 3 means there are 3 molecules of [tex]O_{2}[/tex]. The 2 means there are two atoms of oxygen in each molecule.
Express these temperatures in degrees Fahrenheit and in kelvins. A.-252.97 C B. -40 C C. 1,064 C
Answer:
A. -423.346 °F, 20.18 K
B. -40°F, 233.15K
C. 1947.2 °F, 1337.15 K
Explanation:
A.
(-252.97 °C × 9/5) + 32 = -423.346 °F
-252.97 °C + 273.15 = 20.18 K
B.
(-40 °C × 9/5) +32 = -40 °F
-40 °C + 273.15 = 233.15 K
C.
(1064 °C ×9/5) + 32 = 1947.2 °F
1064 °C + 273.15 = 1337.15 K
Consider the fatty acid. A carboxylate salt is attached to a 19 carbon chain, where double bonds are present between carbons 5 and 6, between carbons 8 and 9, between carbons 11 and 12, and between 14 and 15. The carboxylate carbon is carbon 1. All double bonds are cis. Which of the designations are accurate for the fatty acid
Answer:
ω-3 fatty acid and 19:4(Δ5,8,11,14)
Explanation:
From the image attached below:
We can see the structure of the delta nomenclature showing the numbers of carbons, numbers of double bonds, and the locations of the double bonds in the structure of the carboxylate salt.
Also, we can see the structure of the fatty acid where; the location of the first double bond from the methyl end is shown.
Hence, the designation which are accurate for these structures are:
ω-3 fatty acid and 19:4(Δ5,8,11,14)
what does pen mean?.
Answer:
P = protons
E = electrons
N = neutrons
remember protons and neutrons (protons are positive and neutrons are neutral as you can already tell by their names) are found at the centre of the nucleus (positive mass). Whilst the electrons (negative) orbit around the shells
Which rank was NOT included in Linnaeus' taxonomy?
Kingdom
Family
Domain
Order
Answer:
Domain
Explanation:
This is because Linnaeus taxonomy is a system of classification which was invented by a swedish Botanist called Carl Linnaeus and it is refered to hierarchy of grouping organisms called taxa. It involve 7 system of classifications and they include Kingdom, Phylum, Class, Order, Family, Genus, and Species.
What is the pressure inside a balloon that contains 10.0 g of helium at 25.0°C when the helium occupies a volume of 56.0 L?
A 10.9 atm
B 0.916 atm
C 11.1 atm
D 1.09 atm
Explanation is in the file
tinyurl.com/wpazsebu
when solid copper chloride is mixed with water, a transparent blue solution is created. what is the copper chloride called?
Answer:
cuprous chloride
Explanation:
Copper dichloride
Copper(II) chloride
Copper(II) chloride/IUPAC ID
Na + H2O = NaOH
Balance the following equation
Answer:
Na+H2O =NaO+ H2
Explanation:
Because nitrogen is one , so it is balanced. And Oxygen is one,it is balanced. And Hydrogen is 2 ,and hence it is also balanced.
A pair of molecular orbitals is formed by.
