Why are masses listed on the periodic table not whole #'s. Ex. 15.9999 for oxygen?​

The ratio of the low temperature to high temperature of the Carnot engine is 2.38.

The efficiency of the Carnot engine can be defined as the ratio of network done per cycle by the engine to the heat energy absorbed by the engine per cycle by the working substance from the source.

Efficiency = 1 - (Tlow/Thigh)


Heat absorbed by engine = 480J

Heat expelled by engine = 320J

Efficiency of the engine = 56% of efficiency of Carnot engine

The ratio of low temperature to high temperature in the Carnot engine.

Let's assume the efficiency of the Carnot engine is 'ηc' = 1 - T₂/T₁

Where, T₂ = Low temperature and T₁ = High temperature

To calculate the efficiency of the engine given, η = (Q1 - Q2)/Q1

η = (480 - 320)/480

η = 160/480

η = 1/3

η = 33.33%

Now, η = 56% × ηc

0.56ηc = 1/3ηc = (1/3)/0.56 = 0.58

As we already know, ηc = 1 - T₂/T₁

T₂/T₁ = 1 - ηc

T₂/T₁ = 1 - 0.58

T₂/T₁ = 0.42

T₁/T₂ = 1/0.42

T₁/T₂ = 2.38

Therefore, the ratio of low temperature to high temperature in the given Carnot engine with an efficiency of 56% will be about 2.38.

Learn more about Carnot engine here:

https://brainly.com/question/14680478

#SPJ11

The dragster's change in velocity due to the parachute can be calculated using the kinematic equation:

Δv = aΔt

where Δv is the change in velocity, a is the acceleration, and Δt is the time interval during which the acceleration occurs. In this case, the dragster is initially travelling east, so its velocity is positive, and the parachute applies a force in the opposite direction, resulting in a negative acceleration.

Given that the acceleration is -10 m/s² (westward) and the time interval is 4.5 seconds, we can calculate the change in velocity as:

Δv = (-10 m/s²) x (4.5 s) = -45 m/s

Therefore, the dragster's change in velocity due to the parachute is -45 m/s (westward). This means that the dragster's velocity is reduced by 45 m/s in the westward direction over the 4.5-second interval during which the parachute is deployed.

To know more about velocity , visit :

https://brainly.com/question/17127206

#SPJ1

The change in velocity due to the parachute is -45 m/s east

What is velocity ?

Velocity is a vector quantity that describes the speed and direction of motion of an object. In other words, velocity is the rate at which an object changes its position in a specific direction.

Velocity is expressed in units of distance per time, such as meters per second (m/s) or kilometers per hour (km/h)

Velocity is different from speed, which is also a measure of the rate of motion but only describes how fast an object is moving, without taking into account the direction of motion.

we will use the formula :-

change in velocity = acceleration x time

where acceleration is the rate at which the dragster slows down, and time is the duration for which it slows down.

Here, the dragster is travelling east, and the parachute applies a force in the opposite direction (west), causing it to slow down. So, the acceleration is -10 m/s^2 (negative because it's in the opposite direction to the velocity).

The time for which the dragster slows down is 4.5 seconds.

Therefore, the change in velocity due to the parachute is:

change in velocity = acceleration x time

change in velocity = (-10 m/s^2) x (4.5 s)

change in velocity = -45 m/s east

Note that the velocity is negative because the dragster is slowing down, and it's still travelling east (i.e., in the positive direction).

To know more about velocity visit :-

https://brainly.com/question/80295

#SPJ1

Rutherfordium is a synthetic element with the atomic number 104 and symbol Rf. As a synthetic element, it is not found naturally on Earth and is produced through nuclear reactions in laboratories.

Rutherfordium is a member of the transition metals group and is expected to have similar physical and chemical properties to its neighboring elements in the periodic table. However, due to its radioactive nature and short half-life, its physical properties are difficult to determine.

While there is no experimental data available on the state of matter of rutherfordium at room temperature, it is expected to be a solid metal, similar to other transition metals, such as copper or nickel.

To learn more about matter refer to:

brainly.com/question/28591826

#SPJ4

"The surface of the sun appears sharp in visible light because the photosphere is thin compared to the other layers in the sun."

Most of the electromagnetic energy that reaches the earth begins in the photosphere, the area of the sun that is visible to us. The photosphere is referred to as the sun's surface, despite the fact that it is a gaseous entity.

The gas in the photosphere appears to have a sharp surface, but in reality, it is heavier lower in the Sun and less dense higher up. It is more transparent the less thick it is. The area of the gas that is visible to us is where it has largely become translucent. About 300 km of this layer are deep.

The photosphere is the line separating the core of the Sun from its atmosphere. It is the part of the Sun's surface that is visible to us. The photosphere is not like a planet's surface; even if you could stand in the sun, you couldn't do so on the photosphere.

To know more about Sun:

https://brainly.com/question/12498469

#SPJ4

Answer:

8.04 seconds

Explanation:

Assuming that the child starts from rest at the bottom of the hill and travels until she comes to a stop, we can use the following kinematic equation:

v_f^2 = v_i^2 + 2ad

where v_f is the final velocity (which is zero since the child comes to a stop), v_i is the initial velocity (which is the velocity at the bottom of the hill), a is the acceleration (-0.392 m/s²), and d is the distance traveled.

We can solve for d:

d = (v_f^2 - v_i^2) / (2a)

= (0 - v_i^2) / (2-0.392)

= v_i^2 / 0.784

Since the child is sliding along flat snow-covered ground, there is no change in elevation, so we can use the distance traveled from the bottom of the hill to the stopping point as the distance d.

To find the time it takes for the child to travel this distance, we can use the following kinematic equation:

d = v_it + 0.5a*t^2

where t is the time and all other variables are as previously defined.

Substituting the expression for d obtained above, we get:

v_i^2 / 0.784 = v_it + 0.5(-0.392)*t^2

Solving for t, we get:

t = (2 * v_i) / 0.392

We still need to find the value of v_i, the initial velocity of the child at the bottom of the hill. To do so, we can use conservation of energy. The child starts at rest at the top of the hill, so all the initial energy is potential energy. At the bottom of the hill, all the potential energy has been converted to kinetic energy. Assuming no energy is lost to friction, we can equate these two energies:

mgh = 0.5mv_i^2

where m is the mass of the child, g is the acceleration due to gravity (9.8 m/s²), and h is the height of the hill.

Solving for v_i, we get:

v_i = √(2gh)

Substituting this expression for v_i into the expression for t obtained earlier, we get:

t = (2 * √(2gh)) / 0.392

Plugging in the values of g, h, and a, we get:

t = (2 * √(29.820)) / 0.392 = 8.04 seconds

Plants help to reduce water runoff and soil erosion, both of which affect the health of streams and rivers by impacting water quality.

Soil erosion increases the silt load in the water, which can smother living organisms, particularly plants and invertebrate species. Runoff water can carry pollutants, particularly pesticides, and herbicides from agricultural land.

Landscape 1 (streams cutting through small farms with a variety of crop types and natural vegetation buffers between the fields and the streams) would be the best quality, followed by Landscape 2 (a large floodplain area covered in lowland forests and swamps full of emergent vegetation, with small streams cutting through the area) and Landscape 3 (an urban housing development where the streams are surrounded by emergent vegetation).

Learn more about water quality at  brainly.com/question/20848502

#SPJ11

The speed of the block at the bottom of its slide is 16.4 m/s.

In the previous problem, the kinetic energy of the block was found to be 135 J.

The formula for kinetic energy is

KE = 1/2mv²,

Where:

Now we can use the same formula to find the velocity of the block at the bottom of its slide.

KE = 1/2mv²

We know that the mass of the block is 2 kg, and the kinetic energy at the end of the slide is 135 J.

KE = 135 Jm = 2 kg1/2mv² = 135 Jv² = 2(135 J) / 2 kgv² = 270 JV = sqrt(270 J) / 2 kgV = 16.4 m/s

Therefore, the speed of the block at the bottom of its slide is 16.4 m/s.

Learn more about kinetic energy: https://brainly.com/question/8101588

#SPJ11

Based on the given question, the resistance will: increase with the increase in voltage.

The reason behind this is that resistance and voltage have a direct relationship. As the voltage increases, the resistance also increases. This can be explained by Ohm’s Law which states that V= IR where V is voltage, I is current and R is resistance. As per the second part of the question, it is implied that the resistance varies with temperature.

The resistance of any material depends upon temperature, and a rise in temperature increases the resistance of the material. The light bulb acts as a resistor, and its resistance will increase as the temperature increases due to an increase in the temperature of the filament of the bulb.

The resistance is directly proportional to the temperature of the bulb, and it is represented by the equation

R = R₀ (1 + αt),

where R is resistance, R₀ is the resistance at a particular temperature, α is the temperature coefficient of resistance, and t is the temperature difference in Celsius.

Therefore, based on the data provided, it can be concluded that resistance increases with the increase in temperature which results in the heating of the light bulb, which is a resistor.

To know more about resistance refer here:

https://brainly.com/question/29427458#

#SPJ11

The frequency that the bad guy hear is 12000 hz when the police car is moving with speed of 80m/s.

For more information on doppler effect kindly visit to

https://brainly.com/question/15318474

#SPJ1

The kinetic energy of the object at its final position is 90.98 J.Given,Mass, m = 4.4 kg Initial position, r1 = (2 i + 5 j) m, Final position, r2 = (6 i − 2 j) m ,Initial velocity, u = 4.9 m/s ,Constant resultant force, F = (4 i − 3 j) N .To find the work done by the force,First, we need to find the displacement vector = r2 - r1= (6 i − 2 j) - (2 i + 5 j)= (6 - 2) i + (-2 - 5) j= 4 i - 7 j

Magnitude of the displacement vector,= √(4² + (-7)²)= √65 m Now, we can find the work done by the force,W = F.s= (4 i - 3 j) . (4 i - 7 j)= 4(4) + 3(7)= 37 J

Therefore, the work done by the force is 37 J.

To find the kinetic energy of the object at its final position,First, we need to find the final velocity of the object by using the work-energy principle.Initial kinetic energy, K1 = (1/2)mu²= (1/2) × 4.4 × (4.9)²= 53.98 J

Work done by the force, W = 37 JFinal kinetic energy, K2 = K1 + W= 53.98 + 37= 90.98 JTherefore, the kinetic energy of the object at its final position is 90.98 J.

For such more questions on displacement

https://brainly.com/question/28952425

#SPJ11

The correct comparison of the energy generation processes is "The Sun generates energy by fusing small nuclei into larger ones, while our power plants generate energy by the fission (splitting) of large nuclei". Thus, the correct options are A and B.

Nuclear reactions involve the alteration of an atom's nucleus in both cases. Nuclear power plants and the sun both use energy generated by these nuclear reactions to produce electricity. The difference is in the type of nuclear reaction that takes place.

In the Sun, nuclear fusion is the process by which atomic nuclei of low atomic number fuse to form a heavier nucleus with the release of energy. The energy produced in this way is what makes the Sun so hot and bright. In a nuclear power plant, nuclear fission is the process by which the nucleus of an atom is split into two smaller nuclei.

The energy that is released in the process is used to heat water, creating steam that drives a turbine, which in turn drives a generator to produce electricity.

Therefore, the correct options are A and B.

Learn more about Nuclear power here:

https://brainly.com/question/18769119

#SPJ11

The coordinated functions of the Nervous, Endocrine, and Reproductive systems are:

Coordinated functions refer to the integration and communication between different organs, systems, and tissues in the body to achieve a common goal or purpose. In biological terms, coordinated functions often involve multiple physiological systems working together to maintain homeostasis, respond to stimuli, or carry out complex behaviors or processes.

Examples of coordinated functions include the regulation of blood glucose levels by the pancreas and liver, the coordination of movement by the nervous and musculoskeletal systems, and the release of hormones by the endocrine system to control various physiological processes.

Learn more on coordinated functions here: https://brainly.com/question/15686131

#SPJ1

The question is:

"COORDINATED FUNCTIONS OF THE NERVOUS, ENDOCRINE, AND REPRODUCTIVE SYSTEMS"

Directions: Identify the part of the brain that is involved in each situation below. Write only the letter of your answer.

A. Amygdala

B. Brocka's Area

C. Cerebellum

D. Cerebrum

E. Hippocampus

F. Occipital Lobe

G. Hippocampus

H. Hypothalamus

I. Inferior Colliculus.

J. Thalamus

K. Pons

L Superior Colliculus

M. Pineal Gland

N. Wernicke's Area

O. Pituitary Gland

1. "My heart tells me that you are the one. I love you so much!"

2. "IAOCEVOY! I don't know what that means. It's all Greek to me!"

3. "Chartreuse, Olive,Turquoise, and Mint are all shades of green."

4. "Janna always wakes up at 4 in the morning, regardless of whether she uses an alarm clock or not."

5. "I don't remember the way going to Myla's house. Can you accompany me there?"

6. Jenny's mother is about to give birth, she complains about contraction and pain usually when the baby is kicking

7. "Anthony is a very skilled dancer. He just won the school hip hop dance competition last week."

8. "As Nica was walking on the road she readily moved to the side for she heard an incoming ambulance"

9. "Elsa loves making faces whenever she talks to her friends."

10. "Ryan usually talks about how happy his high school days were to his grandchildren."

Exactly at noon, as determined by the WWV time signal, on successive days of a week the clocks according to their relative value as good timekeepers, best to worst.

Time signals are also used in many everyday applications, such as GPS navigation, where precise timing is essential for calculating positions accurately.  A time signal refers to any signal that provides information about the passage of time. Time signals are often used in experiments to measure the duration of events or to synchronize the timing of multiple processes.

One common type of time signal is a periodic signal, which repeats itself at regular intervals. This can be used to measure the period or frequency of a phenomenon, such as the oscillation of a pendulum or the vibration of a guitar string. Another type of time signal is a pulse signal, which provides a brief burst of energy at a specific time. This can be used to trigger the start or stop of a process or to measure the time delay between different events.

To learn more about Time signal visit here:

brainly.com/question/28875779

#SPJ4

Water droplets that act as prism are phenomenon known as : b) rainbow.

When light enters water droplet and is refracted, it is dispersed into its component colors due to difference in the index of refraction of each color of light. This results in band of colors in the shape of arc with red on outer edge and violet on inner edge, with other colors of spectrum in between. This is the same effect as prism which disperses light in the same way.

Rainbows appear in seven colors because water droplets break sunlight into seven colors of spectrum and you get the same result when sunlight passes through prism. Water droplets in the atmosphere act as prism though traces of light are very complex.

To know more about rainbow, refer

https://brainly.com/question/1550509

#SPJ1

The point at which the warning will do no good is 7.50 m above the man's ears.

When a water-filled balloon is released from rest at a height of 10.0 m above the ears of a man, the warning will do no good if shouted after the balloon reaches a certain point. Assuming that the air temperature is 20°C and ignoring the effect of air resistance, this point is 7.50 m above the man's ears.

The vertical displacement (d) can be determined using the equation [tex]d = \frac{vf2}{2g}[/tex], where vf is the final velocity and g is the acceleration due to gravity (9.81 m/s2).

Since the balloon was released from rest, the initial velocity is 0 m/s. Therefore, [tex]d = \frac{02 }{ 2} (\frac{9.81 m}{s2} ) = 0[/tex]m. Since the initial height was 10.0 m, the final height is 10.0 m + 0 m = 10.0 m.

The point at which the warning will do no good is 7.50 m above the man's ears, so the final height of the balloon must be 10.0 m - 7.50 m = 2.50 m.

Therefore, the point at which the warning will do no good is 7.50 m above the man's ears.

Learn more about vertical displacement: brainly.com/question/2289543

#SPJ11

As a positively charged glass rod is brought near the knob of the electroscope, the separation of the leaves will increase.

What is Charge?

Charge is a fundamental property of matter that determines how objects interact with each other through the electromagnetic force. It is a physical property that can be positive or negative and can be measured in coulombs (C).

This is because the positively charged glass rod will induce a negative charge on the metal knob of the electroscope. The negative charges will repel the electrons in the metal leaves, causing them to move away from each other and increasing their separation. The greater the amount of charge on the glass rod, the greater the separation between the leaves will be.

Learn more about Charge from given link

https://brainly.com/question/18102056

#SPJ1

The angle of repose or the angle of friction is the angle at which the block starts to slide down the inclined plane. By balancing the forces operating on the block along the inclination, it may be calculated.

The gravitational force (mg) acting downhill and the normal force (N) acting perpendicular to the inclination are the forces acting on the block. The gravitational force component perpendicular to the inclination, which is calculated as mg cos, where is the angle of the incline, and the normal force are identical in magnitude.

The block can have a maximum static friction force (Ff) applied to it without it sliding down the incline if:

Ff = μs N

where s is the static friction coefficient.

The amount of the frictional force is equal to the component of the gravitational force parallel to the inclination, which is mg sin, at the instant the block just starts to slide.

learn more about angle here:

https://brainly.com/question/28451077

#SPJ4

The average arterial pressure in your hands when they are held at your side is 47.5 mmHg.

The average arterial pressure in your hands when they are held at your side can be determined using the hydrostatic pressure formula, which is a function of height, gravity, and density. When the hands are held at the side, they are 60 cm below the heart, which means they are at a distance of 0.6 m.

The hydrostatic pressure formula is given by

P = ρgh

Where,

P is the pressure, ρ is the density, g is the acceleration due to gravity, and h is the height. We can assume that the density of blood is constant, and we can take the value of g to be 9.81 m/s², the standard acceleration due to gravity.

Therefore, the pressure at the heart is 100 mmHg, or 100/760 = 0.131 atm. The pressure in the hands can be calculated as follows:

P = ρghP = (1.06 × 10³ kg/m³) × (9.81 m/s²) × (0.6 m)

P = 6.26 × 10³ N/m²

P = 6.26 × 10³ Pa

P = 47.5 mmHg

Therefore, the average arterial pressure in the hands when they are held at the side is 47.5 mmHg.

Learn more about hydrostatic pressure at https://brainly.com/question/28206120

#SPJ11

Coordinate , A - the height of the stone when it hits the water. A slingshot sends a stone vertically upward from a height of 20 feet above a pool of water.

The coordinate A represents the height of the stone when it hits the water. When the stone hits the water, its height above the water surface is zero.

So, we can set the expression for the stone's height equal to zero and solve for t to find the time when the stone hits the water. The height of the stone when it is launched is given as 20 feet, which is a fixed value in this problem.

The time when the stone is launched is also a fixed value, which is zero. The maximum height of the stone is the highest point the stone reaches above its initial height of 20 feet. The time when the stone reaches its maximum height is the time at which the vertical velocity of the stone becomes zero.

To know more about vertical velocity , visit :

https://brainly.com/question/11679227

#SPJ1

The volume of the gas varies inversely with pressure, and the correct answer is (b) P/3.

According to Boyle's Law, at a constant temperature, the volume of a gas is inversely proportional to its pressure. Mathematically, this can be expressed as:

PV = k

where P is the pressure of the gas, V is its volume, and k is a constant.

If we assume that the mass of the gas remains constant, then k is also constant. So we can write:

[tex]P_1V_1 = k and P_2V_2 = k[/tex]

where[tex]P_1 and V_1[/tex] are the initial pressure and volume, and [tex]P_2 and V_2[/tex] are the final pressure and volume.

If we divide these two equations, we get:

[tex]P_1V_1/P_2V_2 = 1[/tex]

Since[tex]V_1[/tex] is inversely proportional to [tex]P_1[/tex], we can write:

[tex]V_1 = k/P_1[/tex]

Similarly, [tex]V_2 = k/P_2.[/tex]

Substituting these values in the above equation, we get:

[tex](k/P_1)/(k/P_2) = 1[/tex]

Simplifying this, we get:

[tex]P_2/P_1 = V_1/V_2[/tex]

Since we are given that the temperature remains constant, we can assume that k is constant, and therefore:

[tex]V_1/P_1 = V_2/P_2[/tex]

If we let [tex]P_2 = 3P_1[/tex], then we get:

[tex]V_1/P_1 = V_2/(3P_1)[/tex]

Simplifying this, we get:

[tex]V_1/V_2 = 1/3[/tex]

for such more question on volume

https://brainly.com/question/14197390

#SPJ11

. Additionally, Star 1 has prominent hydrogen lines, indicating a lower temperature than Star 2. Therefore, the statements can be sorted into the true and false bins as indicated above.

True: Star 1 has a longer lifetime than Star 2; Star 2 is bluer than Star 1; Star 2 has a lower mass than Star 1; Star 1 has prominent hydrogen lines.

False: Star 2 has a higher luminosity than Star 1; Star 2 is cooler than Star 1.

The spectra of the two main sequence stars illustrate some differences between the two stars. Star 1 is on the left and has a longer lifetime than Star 2, which is on the right. This is evident from the intensity axes that are not on the same scale. Star 2 has a lower mass than Star 1, is bluer than Star 1, and has a lower luminosity

for such more questions on hydrogen lines

https://brainly.com/question/30461609

#SPJ11

The expression for the magnitude of the force exerted on the firefighter by the pole can be expressed as  F = mg + ma.  

Where m is the mass of the firefighter,

g is the acceleration due to gravity, and

a is the acceleration of the pole

In order to find an expression for the magnitude of the force, F, exerted on the firefighter by the pole, we need to consider the forces acting on the firefighter.

According to Newton's second law of motion, the force acting on an object is equal to its mass multiplied by its acceleration. In this case, the forces acting on the firefighter are the gravitational force, which is pulling the firefighter downwards with a force of mg, and the force exerted on the firefighter by the pole, which is pushing the firefighter upwards with a force of ma. Therefore, the total force acting on the firefighter is given by the sum of these two forces, which is: F = mg + ma

Thus, this expression gives us the magnitude of the force exerted on the firefighter by the pole. Here, m is the mass of the firefighter, g is the acceleration due to gravity, and a is the acceleration of the pole. if the pole is not accelerating (i.e., if a = 0), then the expression reduces to F = mg, which is the gravitational force acting on the firefighter.

To know more about Magnitude please visit :

https://brainly.com/question/30337362

#SPJ11

At the shop, Joselyn purchased 2700 grammes of salt water taffy.

To convert kilograms (kg) to grams (g), Joselyn would need to multiply the weight in kilograms by 1000. This is because there are 1000 grams in 1 kilogram. Therefore, to find out how many grams of salt water taffy Joselyn bought, she would need to multiply 2.7kg by 1000.

The correct answer is (B) Multiply by 1000.

Multiplying 2.7kg by 1000 gives:

2.7kg x 1000 = 2700g

So Joselyn bought 2700 grams of salt water taffy at the store.

To learn more about salt water refer to:

brainly.com/question/6829606

#SPJ4

Hydroelectric energy is generated by capturing the energy of flowing water. As water flows through a turbine, the blades of the turbine spin and generate electricity.

Wind energy is generated by capturing the kinetic energy of the wind. As wind passes through the turbine, the blades spin and generate electricity.

Geothermal energy is generated by harnessing the natural heat of the Earth’s core. Heat from the Earth’s core is used to generate steam, which is then used to spin a turbine and generate electricity.

Parabolic solar collection is a method of collecting the sun’s energy using large reflective mirrors. The mirrors focus the sunlight onto a central point, which is then used to spin a turbine and generate electricity.

Thus, all of these power sources rely on spinning turbines connected to a generator to produce electricity.

Read more about Electricity here:

https://brainly.com/question/158098

#SPJ11

The correct answer is option D.2 years

According to Kepler's Third Law of Planetary Motion, T² is proportional to r³, where T is the period of revolution of the planet and r is the distance between the planet and the star.

In order to solve for T,  

AU = 1

Astronomical Unit = the average distance between the Earth and the Sun = 149.6 million kilometres

Therefore, the planet is orbiting at a distance of 149.6 million kilometres from the star.

Substituting the values of r and solving for

T².T² ∝ r³T² ∝ (149.6)³T²

= (149.6)³T²

= 3.522 x 10¹²T

= √3.522 x 10^¹²T

= 1.87 x 10⁶ seconds

T = 31,100 minutes

T = 518 hours

T = 21.6 days

T = 2 years

Therefore, the orbital period of the planet with twice the mass of Earth orbiting at a distance of 1 AU from a star with the same mass as the Sun is 2 years.

To know more about Kepler's third law of planetary motion:

https://brainly.com/question/4978861

#SPJ11

Answer: Noble Gases (Blue)

The electric potential energy, U, of two point charges is given by the equation, U = kq1q2/r where k is Coulomb's constant, q1 and q2 are the charges and r is the distance between the two charges. Now, let's solve the question using this equation. There are two charges, q1 and q2, and a parallel plate capacitor between them. The distance of q1 from the negative plate is s, and the distance of q2 from the negative plate is 2s. The charges have the same magnitude of charge, so let's assume q1 = q2 = q. Using the formula mentioned earlier, we get U1= kq^2/sU2= kq^2/2s. Therefore, the ratio of their potential energies is U2/U1= kq^2/2s / kq^2/sU2/U1= (kq^2/2s) × (s/kq^2)U2/U1= 1/2.

Therefore, the ratio of their potential energies is 1:2.

For more information regarding this topic, you can click the below link

https://brainly.com/question/14306881

#SPJ11

When one stationary object is replaced by another stationary object, the change between the two objects maybe perceived as the movement of a single object. This creates an optical illusion.

An optical illusion is defined as a visual phenomenon in which the information gathered by the eye is processed in a way that results in a false perception of reality or the visual impression of seeing something that is not present or incorrectly perceiving it. It is a misinterpretation of a visual stimulus caused by the brain's ability to misjudge sensory information.

It can happen when visual information is processed in the brain, and it can create an impression of movement that isn't there. This phenomenon occurs when an object is moving or when the eyes are moving around, but it can also happen when the object being looked at is stationary.

When one stationary object is replaced by another stationary object, the change between the two objects maybe perceived as the movement of a single object. This creates an optical illusion because the visual system is misled into thinking that the object is moving.

The brain continues to process visual information even when the object is stationary, creating the impression that the object is moving. This is why an optical illusion can be used to make a stationary object appear to move or to make a moving object appear to be stationary.

Learn more about optical illusion: https://brainly.com/question/3260067

#SPJ11

The resulting displacement will be 3.4 km. The correct option is A.

The displacement is calculated by finding the displacement from east to west, which is 2.0 km, and subtracting the displacement from north to south, which is 1.0 km.

A student walks 1.0 kilometers due east and 1.0 kilometers due south. Then she runs 2.0 kilometers due west. The magnitude of the student's resultant displacement is closest to 3.4 km.

To begin with, we may use the Pythagorean Theorem to determine the resultant displacement's magnitude. The Pythagorean Theorem is a formula that is used to determine the length of a right triangle's sides when one is missing. This theorem is used to calculate the magnitude of the resultant displacement, which is a quantity. It's a good idea to draw a diagram to help you understand the problem.

Here's a rough sketch of the scenario: We will now apply the Pythagorean theorem in this way: The resultant displacement's magnitude is 3.4 kilometers. Thus, the correct option is A.

To know more about displacement follow

https://brainly.com/question/14637077

#SPJ11