Answer:because developed cities are more equipped to deal with raw sewage than less developed cities
Explanation:
10 pts!!!!!! please answer ASAP picture and inscription included
The wavelength of a wave is equal to the distance from one disturbance to
the next and is measured in meters. If the distance between two wave
crests is 2 m, what is the wavelength?
Answer:
2m
Explanation: a crest is a disturbance
Answer:
I think its 4m, but don't quote me. hope I helped
Determine the magnetic flux through a square loop of side a if one side is parallel to, and a distance b from a straight wire that carries a current I.
1. If the loop is pulled away from the wire at speed v, what emf is induced in it?
2. Which way does the induced current flow through the loop?
3. How does the emf vary in time, if the initial position of the left vertical side was b0 at time t=0?
4. Determine the force F required to pull the loop away from the line of current.
Answer:
Find the given attachments
Uranium-235 has 92 protons. How many neutrons does it have?
Answer:
146 neutrons.
Explanation:
plzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz mark me brainliest
Answer: The atomic number of uranium (see periodic table) is 92, and the mass number of the isotope is given as 238. Therefore, it has 92 protons, 92 electrons, and 238 — 92 : 146 neutrons.
Explanation:
IS IT right to the left a b c d
Answer:
c ok
Explanation: right?
Answer:
16
Explanation:
A sphere of radius 10.0cm is moulded into a uniform cylindrical wire of same radius r calculate length in millimeters
Answer:
133.33 mm
Explanation:
First we need to find the volume of the sphere. The volume of a sphere is given by:
V = (4/3) * pi * r^3
With a radius of 10 cm, we have:
V = (4/3) * pi * r^3 = 4188.79 cm3
The sphere will be moulded into a cylinder, so the volume will be the same. The volume of a cylinder is:
V = pi * r^2 * h
Where h is the height of the cylinder, and for this case, it will be the length.
The radius is the same old radius, so we have:
4188.79 = pi * 10^2 * h
h = 4188.79 / 100pi = 13.3333 cm
In millimeters, we have h = 133.33 mm
Diffraction of white light with a single slit produces bright lines of different colors.What is the color of the central image?
Answer:
white
Explanation:
This experiment causes lines of different colors because the constructive interference depends on the wavelength, so for different wavelength, the position of the maximum will be different.
Now, in diffraction fo a single slit we always have a central maximum (for all the colors)
This means that after the diffraction, we will have that all the colors have a maximum in the center, which will produce white light again, then the color of the central image is white
Rohit placed a pencil perpendicular to principal axis in front of a converging
mirror of focal length 30 cm. The image formed is twice the size of the pencil.
Calculate the distance of the object from the mirror.
Answer:
45 cm ( in my opinion)♀️
Explanation:
( Using the mirror formula)
1/ u + 1/v = 1/f
( introducing magnification; m into the formula )
u( 1/u + 1/v ) =u×1/f
1 + u/v =u/f
( But u/v =1 ÷v/u= 1/m)
1 +1/m =u/f
(Supposing m is actually equal to 2, and f =30 cm, then;)1 + 1/2 =u/30
2+1= u/15
3=u/15
3×15=u
45 cm=u
Ski lift carry people along 150 m cable up the side of a mountain. Riders are lifted a total of 75 m in elevation. What is the ideal mechanical advantage of the ski lift?
Ideal Mechanical Advantage (IMA) can be found by using the formula:
IMA = ID/OD
ID = Input Distance
OD = Output Distance
In the question, we are given:
ID = 150
OD = 75
Now, solve the expression with what we have.
IMA = 150/75
IMA = 2
Therefore, the IMA is 2.
Best of Luck!
A 1 kg ball is rolling at 3 m/s.
Answer:
It will roll 9 meters in 3 seconds
Explanation:
3 m/s times 3 is 9
Thanks for warning me.
I'll be careful to stay out of its way.
Do you have a question to ask ?
Need help on circuit question
(x) A change in position is called:
(a) Speed
(b) velocity
(c) displacement
(d) distance
Answer:
(c) displacement
sure answer...
Hope it helps....Pls mark as Brainliest!!!
Do u think the benefits of nuclear energy outweigh the dangers
Answer:
While there is no such thing as 100 percent safe, having nuclear energy is much safer than you think. It's thousands of times safer than conventional coal and other fossil-fuel-derived energy, not to mention the specter of environmental disaster from continued use of carbon-based energy sources.29 may. 2011
Explanation:
I hope it helps you
Which nanotechnology product would most likely help the
electronics company?
biomaterials
carbon wires
quantum dots
OLEDs
Answer: OLEDs
Explanation:
The nanotechnology uses the surface of the carbon materials to generate the electricity. The evaporation of water on the surface of carbon materials helps in generation of electrical energy due to generation of thermal energy.
OLEDs can be defined as solid-state devices that comprises of organic molecules like carbon that will create electricity by exposing a surface for generation of thermal energy.
A chocolate wrapper is 6.7 cm long and 5.4 cm wide. Calculate its area up to
reasonable number of significant figures.
How old does an individual need to be in the United states to purchase any tobacco products
Answer: 18 years of age
Explanation:
What do you think happened to the energy you transferred to the notebook when you pushed it?
Answer:
It got transferred to kinetic energy
Explanation:
Answer:
The energy changed from kinetic energy to heat energy. Friction causes heating.
Calculate the first and second velocities of the car with four washers attached to the pulley, using the formulas
v1 = 0.25 m / t1 , and v2 = 0.25 m / (t2 – t1)
where t1 and t2 are the average times the car took to reach the 0.25 and the 0.50 meter marks. Record these velocities, to two decimal places, in Table E
The first and second velocities of the car, with four washers attached to the pulley, are both 0.125 m/s.
We must apply the following calculations to determine the car's first and second velocities with the four washers attached to the pulley:
v1 = 0.25 m / t1
v2 = 0.25 m / (t2 - t1)
Here, t1 denotes the typical time needed for the car to go 0.25 metres, and t2 is the typical time needed to travel 0.50 metres.Let's say that t1 and t2 are the typical times, each lasting two seconds on average.The first formula allows us to determine v1:
v1 = 0.25 m / 2 s = 0.125 m/s
Using the second formula, we can calculate v2:
v2 = 0.25 m / (4 s - 2 s) = 0.125 m/s
Table E can be used to record these values as the velocities at the relevant distances.
for such more questions on velocities
https://brainly.com/question/80295
#SPJ8
Chris has a part time job as a cannon ball catcher for the circus. One day he was located an unknown distance away from the cannon. A cannonball was fired from the cannon at 425 m/s. The speed of sound was 345 m/s. Unfortunately the cannonball went past Chris 0.20 s before he heard the sound of the blast. How far away was the cannon from Chris?
show work with answer for brainliest plz
Answer: 366.56 meters.
Explanation:
Velocity of the cannon ball = 425m/s
Velocity of sound = 345 m/s
For the "position" of both, we have the equation:
Pc = 425m/s*t
Ps = 345m/s*t
Where t is time in seconds.
If the position of Chris is X, we have that if the ball reaches the position of Chris in T seconds, then the soundwave reaches the position of Chris in T + 0.20 seconds, we can write this as:
425m/s*T = X
345m/s*(T + 0.20s) = X
Now we can solve this system of equations. First we can replace the first equation in the second equation and get
345m/s*(T - 0.20s) = 425m/s*T
Now we solve this for T.
345*T + 69 = 425*T
69 = (425 - 345)*T = 80*T
T = 69/80 = 0.8625 seconds.
Now we replace this in the first equation and get:
X = 425m/s*T = 425m/s*0.8625s = 366.56 meters.
what are the dimensions of the rectangle
Answer:
A rectangle has two dimensions:we can measure its length and,perpendicular to that,its width.
Explanation:
Hydrogen is a nonmetal with many nonmetal properties. Why is it on the periodic table with the metals in Group 1?
Answer:
This is because it has ns1 electron configuration like the alkali metals.
Pls Mark Brainiest, am trying to become Virtuoso
Indica qué es una propiedad específica de la materia. Además explica por qué son útiles las propiedades específicas de la materia frente a las generales.
Answer:
Check Explanation
Comprobar explicación
Explanation:
English Translation
Indicate what a specific property of matter is. Also explain why the specific properties of matter are useful compared to the general ones.
Solution
The specific properties of matter are properties that describes the intensive properties of the system. They are properties that do not depend on or change with the extent or size of the system. They are usually obtained by dividing the generalised properties or extensive properties by the extent or size of matter to make them independent of size/extent/Mass.
Examples of specific properties include specific heat capacity, specific volume etc. They usually have units of general units/Mass units.
The specific properties of matter are more important than the general ones because
- They help in general comparisons of the properties of different materials. They are used to rank, classify and compare properties of different materials.
- They are used in reference table/data to easily record easily accessible properties of matter. It helps to record standards that are general and independent of sizes/extents/Mass, thereby keeping the reference table/data/chart precise and concise.
- They provide us with values that are easy to memorize and remember, unlike trying to cram the different properties of different masses/sizes of matter.
In Spanish/En español
Las propiedades específicas de la materia son propiedades que describen las propiedades intensivas del sistema. Son propiedades que no dependen ni cambian con la extensión o el tamaño del sistema. Por lo general, se obtienen dividiendo las propiedades generalizadas o las propiedades extensivas por la extensión o el tamaño de la materia para hacerlas independientes del tamaño / extensión / masa.
Los ejemplos de propiedades específicas incluyen capacidad calorífica específica, volumen específico, etc. Usualmente tienen unidades de unidades generales / unidades de masa.
Las propiedades específicas de la materia son más importantes que las generales porque
- Ayudan en las comparaciones generales de las propiedades de diferentes materiales. Se utilizan para clasificar, clasificar y comparar propiedades de diferentes materiales.
- Se utilizan en la tabla / datos de referencia para registrar fácilmente propiedades de materia fácilmente accesibles. Ayuda a registrar estándares que son generales e independientes de tamaños / extensiones / masa, manteniendo así la tabla / datos / tabla de referencia precisa y concisa.
- Nos proporcionan valores que son fáciles de memorizar y recordar, a diferencia de tratar de agrupar las diferentes propiedades de diferentes masas / tamaños de materia.
Hope this Helps!!!
¡¡¡Espero que esto ayude!!!
El coeficiente de variación de la resistencia con la temperatura del carbón es -0.0005/°c.Si la resistencia de una resistencia de carbón es de 1000 a0°c , determine su resistencia a 120°c
Answer:
R (120) = 940Ω
Explanation:
The variation in resistance with temperature is linear in metals
ΔR (T) = R₀ α ΔT
where α is the coefficient of variation of resistance with temperature, in this case α = -0,0005 / ºC
let's calculate
ΔR = 1000 (-0,0005) (120-0)
ΔR = -60 Ω
ΔR = R (120) + R (0) = -60
R (120) = -60 + R (0)
R (120) = -60 + 1000
R (120) = 940Ω
You have a large flashlight that takes 4 D-cell batteries, each with a voltage of 1.5 volts. If the current in the flashlight is 2.0 amps, what is the
resistance?
A 12 ohms
B 0.75 ohms
C 3.0 ohms
D.0.5 ohms
E. 6.0 ohms
Answer:
The answer is "C. 3.0 ohms".
Explanation:
Ohm's law states the following:,
V = IR
where:
Voltage (V) = 1.5 volts × 4 batteries = 6.0 volts
Current (I) = 2.0 amps
Resistance (R) = ? ohms
To solve for Resistance (R) the equation must be rearranged this way:
R = V / I
Then, the variables must be replaced with the known values:
R = 6.0 volts / 2.0 amp
R = 3.0 ohms
The answer is C. 3.0 ohms.
------------
P.D: I got it right on PLATO
The measured mass of a body is found to be 110g. The length is measured by a meter scale. Actual mass and length of the body are 100 g and 10 cm. Find the percentage error in the calculation of density.
Answer:
ok it will be g+181
Explanation:
A trip is taken that passes through the following points in order
Point A 0 m
Point B 15.0 m
Point C -30.0 m
Point D -20.0 m
Point E 10.0 m
Point F 5.0 m
What is the distance from Point C to Point E?
answers :
20.0 m
40.0 m
-20.0 m
10.0 m
Answer:
40.0 m
...............
Answer:
35
Explanation:
terms used to measure motion
Answer:
velocity term
Explanation:
Answer:velocity term
Explanation:
Object A has a mass of 10 kg and is moving at a velocity of 2.0
m/s. So Object A's momentum is - kg. m/s.
Answer:20kgm/s
Explanation:
Mass=10kg
Velocity=2m/s
Momentum=mass x velocity
Momentum=10 x 2
Momentum=20
Momentum=20kgm/s
The object with mass m when moving with the velocity, its momentum can be calculated. The momentum of the object A is 20 kg.m/s.
What is momentum?Momentum is the product of mass and velocity of a moving object.
If the momentum is p, the mass of the object is 10 kg and the velocity is 2.0 m/s, then the momentum will be
p = 10 × 2.0
p = 20 kg.m/s
Thus, the momentum of the object A is 20 kg.m/s
Learn more about momentum.
https://brainly.com/question/24030570
#SPJ2
When using the lens equation, a negative value as the solution for d baseline i indicates that the image is
A. real
B. virtual
C. upright
D. inverted
When using the lens equation, a negative value as the solution for d baseline i indicates that the image is Virtual. The correct option is B.
What is reflection?When a light strikes on a shiny surface, it reflects back the light ray in the same medium. The phenomenon is called reflection and the ray is called the reflected ray.
From the Len's maker formula, e have
1/f = 1/u + 1/v
where f = radius of curvature /2
So, the negative value as the solution for d baseline i indicates that the image is Virtual.
Thus, the correct option is B.
Learn more about reflection.
https://brainly.com/question/2254222
#SPJ5
Which statement is NOT an advantage of renewable resources? A They produce clean energy. B They are expensive to collect and transform into energy. C They are safe for the environment. D They replenish quickly.
Answer:
B. They are expensive to collect and transform into energy.
Explanation:
All of the other options are positive aspects of renewable resources. B is the only disadvantage of renewable resources given in the question.
Answer:
They are expensive to collect and transform into energy.
Explanation:
Edge
Which of the following particle is responsible for the transfer of static charge?
A. Neutron
B. Electron
C. Proton
D. A & C
Answer:
B. Electron
Static charge is produced by electron transfer.
Explanation:
Answer A: The neutron does not possess a charge and is said to be neutral.
Answer D: Protons and neutrons never move from object to object.
Only negative charges can move freely from one object to another. The energy that comes from these charges particles is called electrical energy.
....
Hope this answer can help you.
The answer is an electron.
