1. Two aluminium strips and a steel strip are to be bonded together to form a composite bar. The modulus of elasticity of steel is 200 GPa and 75 GPa for aluminium. The allowable normal stress in steel is 220 MPa and 100 MPa in aluminium. Determine the largest permissible bending moment when the composite bar is bent about horizontal axis. a
Answers
Answer:
1.933 KN-M
Explanation:
Determine the largest permissible bending moment when the composite bar is bent horizontally
Given data :
modulus of elasticity of steel = 200 GPa
modulus of elasticity of aluminum = 75 GPa
Allowable stress for steel = 220 MPa
Allowable stress for Aluminum = 100 MPa
a = 10 mm
First step
determine moment of resistance when steel reaches its max permissible stress
next : determine moment of resistance when Aluminum reaches its max permissible stress
Finally Largest permissible bending moment of the composite Bar = 1.933 KN-M
attached below is a detailed solution
Related Questions
The efficiency of a steam power plant can beincreased by bleeding off some of the steam thatwould normally enter the turbine and usingit topreheat the water entering the boiler. In this process,liquid water at 50oC and 1000 kPa is mixed withsuperheated steam at 200oC and 1000 kPa. If the plantoperators want to produce a saturated liquid at 1000kPa, what ratio of mass flow rates of water andsuperheatedsteam are required
Answers
Answer:
Explanation:
This is Answer....
what's nested piezometer?
Answers
Explanation:
Nested piezometers indicate an upward flow if the elevation of the top of the water in the piezometer tube that penetrates the aquifer to the deeper point is greater than the elevation of the water in the shallower tube
Air at 25 m/s and 15°C is used to cool a square hot molded plastic plate 0.5 m to a side having a surface temperature of 140°C. To increase the throughput of the production process, it is proposed to cool the plate using an array of slotted nozzles with width and pitch of 4 mm and 56 mm, respectively, and a nozzle-to-plate separation of 40 mm. The air exits the nozzle at a temperature of 15°C and a velocity of 10 m/s.
Required:
a. Determine the improvement in cooling rate that can be achieved using the slotted nozzle arrangement in lieu of turbulated air at 10 m/s and 15°C in parallel flow over the plate.
b. Would the heat rates for both arrangements change significantly if the air velocities were increased by a factor of 2?
c. What is the air mass rate requirement for the slotted nozzle arrangement?
Answers
Answer:
a. 2.30
b. decreases with increasing velocity.
c. 0.179 kg/s.
Explanation:
Without mincing let's dive straight into the solution to the question above.
[a].
The improvement in cooling rate that can be achieved using the slotted nozzle arrangement in lieu of turbulated air at 10 m/s and 15°C in parallel flow over the plate can be determined by calculating turbulent flow:
The turbulent flow over the plate= 10 × 0.5/ 20.92 × 10⁻6 = 2.39 × 10⁵.
While the turbulent flow correlation = 0.037( 2.39 × 10⁵)^[tex]\frac{4}{5}[/tex] (0.7)^[tex]\frac{1}{3}[/tex] = 659.6.
Array of slot noozle = [10 × (2 × 0.004)]/ 20.92 × 10^-6] = 3824.
where A = 4/56 =0.714.
And Ar = [ 60 + 4 (40/2 × 4) - 2 ]^2 ]-1/2 = 0.1021.
N = 2/3 (0.1021)^3/4 [ 2 × 3824/ ( 0.0714 / 0.1021) + (.1021/0.0714)] (0.700)^0.42 =24.3.
h = 24.3 × 0.030/0.004 = 91.1 W/m^2k.
Therefore; 659.6 × 0.030/0.5 = 39.0 W/m²k.
The turbulent flow = 0.5 × 39.6 × 0.5( 140 -15) = 1237.5 W.
The slot noozle = 91.1 × 0.5 × 0.5 [ 140 -15] = 2846.87W.
The improvement in cooling rate = 2846.87/ 1237.5 = 2.30.
[b].
2.3 [ (2^2/3)/ 2^4/5] = 2.1
Thus, it decreases with increasing velocity
[c].
The air mass rate requirement for the slotted nozzle arrangement = 9 × 0.995 (0.5 × 0.004)10 = 0.179 kg/s.
electrical engineering
Answers
Answer:
Electrical engineering is an engineering discipline concerned with the study, design and application of equipment, devices and systems which use electricity, electronics, and electromagnetism.
Explanation:
Derive the next state equations for each type (D, T, SR, and JK) of basic memory element. The next state equation is a symbolic equation describing the next state (Q ) as a function of the inputs (D,T,SR, or JK) and state (Q). In order to determine the next state equations for a a JK memory element, build a 3-variable Kmap with Q, J, and K as the inputs. The entries in the Kmap should be Q . Solving this Kmap will yield the next state equation. Show all work for full credit.
Answers
Answer:
Attached below is the derived next state equations
Explanation:
Attached below is the derived next state equations
used for the solution of the given problem.
A power winch is designed to raise a 4,961 N load 10 meter in 2 minutes. The winch is designed with a 283 mm diameter drum taking up the wire lifting the load. The drum will be connected to a 9 rpm motor through a gearbox. What is the minimum torque (Nm) that the motor shaft coupling should be designed to transmit
Answers
Answer:
T = 438.87 N.m
Explanation:
The power required to raise the 4961 N load in 10 meters for 2 minutes is:
[tex]P = \dfrac{4961*10}{2*60}\\ \\ P = 413.42 Nm/sec[/tex]
P = Torque × W
[tex]413.42 = T \times \dfrac{2 * \pi*9}{60}[/tex]
[tex]413.42 = T \times0.942 \\ \\ T = \dfrac{413.42}{0.942}[/tex]
[tex]T = \dfrac{413.42}{0.942}[/tex]
T = 438.87 N.m
After earning a bachelor's degree, one must do which of the following before taking the PE examination to receive a Professional Engineering license?
Answers
Automotive gas turbines have been under development for decades but have not been commonly used in automobiles. Yet helicopters routinely use gas turbines. Explore why different types of engines are used in these respective applications. Compare selection factors such as performance, power-to-weight ratio, space requirements, fuel availability, and environmental impact.
Required:
Summarize your findings in a report with at least three references.
Answers
Answer:
Gas turbines in Helicopters require lesser space.
Explanation:
[1] In terms of Space Requirements:
The gas used in helicopters requires lesser space as compared to Automotive gas turbines. The gas in automobile have higher thermal efficiency.
[2]. In terms of Environmental impact:
The occurrence of environmental solution is very slim when used in helicopters' engines.
[3]. In terms of power-to-weight ratio:
The vibrations in engines of helicopters make it to have lesser efficiency as compared to automobile.
[4]. In terms of Fuel availability:
Fuel is available. Automobile can make use of gas as fuel.
Leland wants to work in a Production career operating heavy machinery. Which type of education or training should Leland seek?
a bachelor’s degree then a master’s degree
vocational school certificate or master’s degree
on-the-job training or vocational school certificate
associate’s degree then a bachelor’s degree
Answers
Answer:
it is indeed C
Explanation:
Answer:
c
Explanation:
what’s your favorite color of the alphabet? if so, what fruit is it?
Answers
Hi sorry I need points I'm New
Answer: My favorite color is Red favorite letter C favorite fruit watermelon.
The aluminum rod (E1 = 68 GPa) is reinforced with the firmly bonded steel tube (E2 = 201 GPa). The diameter of the aluminum rod is d = 25 mm and the outside diameter of the steel tube is D= 45 mm. The length of the composite column is L = 761 mm. A force P = 88 kN is applied at the top surface, distributed across both the rod and tube.
Required:
Determine the normal stress σ in the steel tube.
Answers
Answer:
Explanation:
From the information given:
[tex]E_1 = 68 \ GPa \\ \\ E_2 = 201 \ GPa \\ \\ d = 25 \ mm \ \\ \\ D = 45 \ mm \ \\ \\ L = 761 \ mm \\ \\ P = -88 kN[/tex]
The total load is distributed across both the rod and tube:
[tex]P = P_1+P_2 --- (1)[/tex]
Since this is a composite column; the elongation of both aluminum rod & steel tube is equal.
[tex]\delta_1=\delta_2[/tex]
[tex]\dfrac{P_1L}{A_1E_1}= \dfrac{P_2L}{A_2E_2}[/tex]
[tex]\dfrac{P_1 \times 0.761}{(\dfrac{\pi}{4}\times .0025^2 ) \times 68\times 10^4}= \dfrac{P_2\times 0.761}{(\dfrac{\pi}{4}\times (0.045^2-0.025^2))\times 201 \times 10^9}[/tex]
[tex]P_1(2.27984775\times 10^{-8}) = P_2(3.44326686\times 10^{-9})[/tex]
[tex]P_2 = \dfrac{ (2.27984775\times 10^{-8}) P_1}{(3.44326686\times 10^{-9})}[/tex]
[tex]P_2 = 6.6212 \ P_1[/tex]
Replace [tex]P_2[/tex] into equation (1)
[tex]P= P_1 + 6.6212 \ P_1\\ \\ P= 7.6212\ P_1 \\ \\ -88 = 7.6212 \ P_1 \\ \\ P_1 = \dfrac{-88}{7.6212} \\ \\ P_1 = -11.547 \ kN[/tex]
Finally, to determine the normal stress in aluminum rod:
[tex]\sigma _1 = \dfrac{P_1}{A_1} \\ \\ \sigma _1 = \dfrac{-11.547 \times 10^3}{\dfrac{\pi}{4} \times 25^2}[/tex]
[tex]\sigma_1 = - 23.523 \ MPa}[/tex]
Thus, the normal stress = 23.523 MPa in compression.
