3
Current is measured in units called

Answers

Answer 1

Answer:

current is measured in Ampere (A)

Answer 2

Answer:

Ampere (A)

Explanation:

The ampere is defined so the elementary charge e is 1.602 176 634 × 10−19 C or A•s.

Hope this helps <3


Related Questions

what is the best book for mechanic of materials?​

Answers

Answer:

As per my experience Egor Popov is one the best book for mechanics of materials.

Explanation:

hope this helps

A steam turbine generator unit is used to produce electricity, where steam enters the turbine with a velocity of 30 m/s and enthalpy (internal energy) of 3348 kJ/kg. The 1 steam leaves the turbine as a mixture of vapor and liquid having a velocity of 60 m/s and an enthalpy of 2550 kJ/kg. The flow through the turbine is adiabatic, and changes in elevation are negligible. Determine the work output from the turbine, if the mass flow rate is 5kg/s.

Answers

Answer:

3.983 MW

Explanation:

Given that:

At the inlet:

Velocity (v₁) = 30 m/s

Enthalpy (h₁) = 3348 kJ/kg

At the outlet:

Velocity (v₂) = 60 m/s

Enthalpy (h₂) = 2550 kJ/kg

Mass flow rate (m) = m₁ = m₂ = 5kg/s

According to the steady flow energy equation:

[tex]Q+ m_1 (h_1 + \dfrac{v_1^2}{2000}+ \dfrac{gz_1}{1000} )= m_2(h_2+\dfrac{v_2^2}{2000}+\dfrac{gz_2}{1000})+W_{shaft}[/tex]

Since the elevation (z) is negligible and flow via the turbine is adiabatic:

Then,

Q = 0 and z₁ = z₂

[tex]W_{shaft} = (mh_1-mh_2) + (\dfrac{mv_1^2-mv_2^2}{2000})[/tex]

[tex]W_{shaft} = ((5*3348) -(5*2550)) + (\dfrac{(5*(30)^2)-(5*(60)^2)}{2000})[/tex]

[tex]W_{shaft} = (16740-12750) + (\dfrac{4500-18000}{2000})[/tex]

[tex]W_{shaft} = (16740-12750) + (-6.75)[/tex]

[tex]W_{shaft} = 3983.25 \ kW[/tex]

[tex]\mathbf{W_{shaft} = 3.983 \ MW}[/tex]

beacuse thye want them to hav egoood and thye wn thme tto

Answers

Answer:

I don't understand the question

I don’t understand what your asking

What is the following diagram called?

Answers

Answer:

flow chart

Explanation:

it's a flow chart right ? don't know the explanation cause I am not even sure I am right

Hydraulic fracturing is: Select one: a. a first step in storage of high-level radioactive waste b. a way of extracting natural gas shale formations c. a step in oil refining where oil is separated into different viscosities d. none of the above

Answers

The answer is B - a way of extracting natural gas shale formations.

Hydraulic fracturing is “a way of extracting natural gas shale formations.”

Shale and other types of "tight" rock, or impermeable rock formations that lock in oil and gas and complicate the production of fossil fuels, can be extracted of their natural gas or oil using the modern high-volume hydraulic fracturing process. Thus, option B is correct.

What are the factor involving in Hydraulic fracturing?

Shale gas is extracted through a procedure called hydraulic fracturing, also referred to as “fracking.” Due to the fact that shale reserves are often dispersed horizontally rather than vertically, deep holes are first drilled into the shale rock, then horizontal drilling is used to reach more of the gas.

A mixture of sand, chemicals, and water is pushed at high pressure down a borehole during hydraulic fracturing. The released gas can flow out of the rocks and back up the borehole because the water pressure causes cracks in the rock to widen, and the sand particles settle into the openings to keep them open.

Therefore, a way of extracting natural gas shale formations.

Learn more about Hydraulic fracturing here:

https://brainly.com/question/28559289

#SPJ2

The impeller shaft of a fluid agitator transmits 20 kW at 430 rpm. If the allowable shear stress in the impeller shaft must be limited to 65 MPa, determine (a) the minimum diameter required for a solid impeller shaft. (b) the maximum inside diameter permitted for a hollow impeller shaft if the outside diameter is 36 mm. (c) the percent savings in weight realized if the hollow shaft is used instead of the solid shaft. (Hint: The weight of a shaft is proportional to its cross-sectional area.)

Answers

Given :

Power, P = 20 kW

Speed, N = 430 rpm

Allowable shear stress, τ = 65 MPa

Torque in the shaft is given by :

[tex]$P=\frac{2 \pi NT}{60}$[/tex]

[tex]$T=\frac{60 \times 20 \times 10^3}{2 \pi \times 430}$[/tex]

T = 444.37 N.m

Diameter of the solid shaft is

[tex]$d=\sqrt[3]{\frac{16 T}{\pi \tau}}[/tex]

[tex]$d=\sqrt[3]{\frac{16 \times 444.37}{3.14 \times 65}}[/tex]

[tex]$d=\sqrt[3]{34.83} $[/tex]

d = 3.265 m

d = 326.5 mm

Internal diameter of the hollow shaft is :

[tex]$\frac{T}{\frac{\pi}{32} \left( d_0^4 - d_i^4 \right)}=\frac{\tau}{d_0/2}$[/tex]

[tex]$\frac{444.37}{\frac{3.14}{32} \left( 0.036^4 - d_i^4 \right)}=\frac{65 \times 10^6}{0.036/2}$[/tex]

[tex]$\frac{444.37}{0.09 \left( 1.6 \times 10^{-6} - d_i^4 \right)}=\frac{65 \times 10^6}{0.018}$[/tex]

[tex]$\frac{7.99}{ \left( 1.6 \times 10^{-6} - d_i^4 \right)}=5850000$[/tex]

[tex]$1.3\times 10^{-6} = 1.6 \times 10^{-6} - d_i^4 \right)}$[/tex]

[tex]$d_i^4=300000$[/tex]

[tex]$d_i = 23.40$[/tex] mm

Percentage savings in the weight is given by :

Percentage saving = [tex]$\frac{W_{solid}-W_{hollow}}{W_{solid}}\times100$[/tex]

                                 [tex]$=\frac{V_{solid}-V_{hollow}}{V_{solid}}\times100$[/tex]

                                 [tex]$=\frac{d^2 - (d_0^2 - d_i^2)}{d^2} \times 100$[/tex]

                               [tex]$=\frac{(326.5)^2 - (0.036^2 - (32.40)^2)}{(326.5)^2} \times 100$[/tex]

                                 [tex]$=\frac{106602 - \left(1.29 \times 10^{-3} - 1049.76 \right)}{106602} \times 100$[/tex]

                                  [tex]$=\frac{106602 - 1049 }{106602} \times 100$[/tex]

                                  [tex]$=\frac{105553 }{106602} \times 100$[/tex]

                                  = 99.01 %

A O.1m³ rigid tank contains steam initially as 500k pa and 200°C. The steam is now allowed to cool until the temperature drops to 50°C. Determine the amount of heat transfer during the process and the final pressure in the tank​

Answers

Answer:

Check it out here

Explanation:

Magnetic particle testing can be done only on metals that can be magnetized.
True or false

Answers

the answer to this it true

What is the following diagram called?

Answers

Answer:

business

Explanation:

because shopping has great income

Answer:

is ur question right

Explanation:

is ur question right

is ur question right

anxiety: a. is never normal. b. is common of many psychological disorders c. is identical to fear d. is a modern development, unlikely to have roots in human history

Answers

Answer:

B

Explanation:

Anxiety is very common especially nowadays but it's especially common in psychological disorders

. Bơm kiểu piston tác dụng đơn có áp suất p=0,64 Mpa và lưu lượng Q=3,5 l/s. Xác định tốc độ quay của trục bơm và công suất của bơm nếu biết đường kính piston D=150 mm; bán kính tay quay R=60 mm; hiệu suất thể tích của bơm là 0=0,94; hiệu suất chung của bơm b=0,80.

Answers

Answer:

not understand language

Work to be performed can come from the work package level of the work breakdown structure as well as other sources. Which of these is NOT a source of authorized work to be performed?

a. Scope creep
b. Defect repairs
c. Preventive actions
d. Corrective actions

Answers

A project is meant to achieve clearly defined goals within present constraints

The correct option for the source of work in a project which is NOT a source of authorized work to be performed is option (a)

a. Scope creep

The reason for the selecting the above option is as follows;

In project management, alongside work planned in a work package, authorized work to be performed can come from;

The repairing of defects found in completed work and which is a requirement for the project to be approvePreventive actions, that are meant to mitigate factors that affect the project timeline and costCorrective actions which include actions meant to rectify parts of the project that produce an error outcome

A scope creep, however, is generally is due to the inclusion of the end

users of the project at a time that is behind schedule, insufficient analysis of

the requirements, and project complexity underestimation. and consists of

changes made after a project has commenced

A scope creep therefore, changes the amount of work to be done which

therefore alters the project timeline, and due to project, budgetary, and

end user constraints, CANNOT be a source of authorized work to be

performed

The correct option for the source that is NOT a authorized work to be performed is option a. Scope creep

Learn more about scope creep here:

https://brainly.com/question/14061926

which type of clectrical circuit is represented by this diagram?​

Answers

Answer:

  parallel

Explanation:

All components in this circuit are tied in parallel. Each component experiences the same voltage from one terminal to the other. It is a parallel circuit.

Troy must keep track of the amount of refrigerant he uses from a 50-pound cylinder to ensure that accurate
records are kept. He used 13 pounds on a systein for Ms. Jones and 9 pounds on a system for a commercial
client. How many pounds should he have left in the cylinder?
tof
Troy should have
pounds of refrigerant left in the cylinder.
baon naid Thamar basic
محمود احمد مجد
12
اهداء ما در

Answers

Answer:

Amount of gas still in cylinder = 28 pound

Explanation:

Given:

Amount of gas in cylinder = 50 pound

Amount of gas used in Ms. Jones system = 13 pound

Amount of gas used in client system = 9 pound

Find:

Amount of gas still in cylinder

Computation:

Amount of gas still in cylinder = Amount of gas in cylinder - Amount of gas used in Ms. Jones system - Amount of gas used in client system

Amount of gas still in cylinder = 50 - 13 - 9

Amount of gas still in cylinder = 28 pound

an atom that gained an electron is called​

Answers

Answer:

Hey mate......

Explanation:

This is ur answer.....

When an atom gains/loses an electron, the atom becomes charged, and is called an ion.

Hope it helps!

Brainliest pls!

Follow me :)

An atom that gained an electron is called an ION.

Rafel knows that lessons learned is a valuable aid to future projects. When should he and his team address
lessons learned on a project?
Select an answer:
Add lessons learned as a topic in status meetings
Review past lessons learned so a new one does not have to be created,
Create lessons learned at the end of the project.
Brainstorm lessons learned at the beginning of a project

Answers

Answer: Create lessons learned at the end of the project.

Explanation:

Lessons learned are the experiences that are gotten from a project which should be taken into account for the future projects. Lesson learned are created at the end of the project.

The main objective of the lessons learned is that they show both the positive experience and the negative experience of a project and this will help the future projects that will be undertaken.

Which of the following conditions were present in over 80% of paddling fatalities from 1995-2000?

Answers

Answer:

80% of the people that were killed weren't wearing a safety flotation device ( in correct terminology Personal Flotation Device, or PFD )

Explanation:

Hence they drowned due to the lack of safety.

The condition present in over 80% of paddling fatalities is that the victims were said to be not wearing a personal flotation device (PFD).

What is paddling in the sea?

The act of paddling is known to be a sport or something one can do for fun or for games.

Conclusively, a lot of paddling fatalities 1995-2000 was due to the fact that the people who were engage in the sport or act were not putting on  a personal flotation device (PFD) and this can lead to death or drowning.

Learn more about  paddling fatalities from

https://brainly.com/question/3787626

True or false: You can create a network with two computers.



Answer
True

Answers

To create a computer network, you must have at least two computers. ... A protocol is a standard set of rules and procedures for the control of communications in a network. TRUE. Two computers using TCP/IP can communicate even if they are based on different hardware and software platforms. So your right :)

Hope this helps :)
True u must use two computers

A resistor has code 104 printed on it .What is the resistive value of this resistor ​

Answers

Answer:

X = 1 (1st digit in the code)

Y = 0 (2nd digit)

Z = 4 (3rd multiplier digit)

104 → 10 × 10^4 Ω

→ 10 × 10000Ω

→ 100 kΩ

resistors are marked 104, 105, 205, 751, and 754. The resistor marked with 104 should be 100kΩ (10x10^4), 105 would be 1MΩ (10x10^5), and 205 is 2MΩ (20x10^5). 751 is 750Ω (75x10^1), and 754 is 750kΩ (75x10^4).

Here we need to understand how a code in a resistor gives us information on the resistor. Here we will see that the code means that the resistance is 100,000 Ω.

When we use numbers, let's assume that we have 3 single-digit numbers abc.

So if the code in our resistor is abc, this will mean that the resistance of the resistor is:

ab×10^c Ω

Using this general rule we can see that if the code is 104, then the resistance will be:

r = 10×10^4 Ω

 = 100,000 Ω

Then we can conclude that the resistive value of this resistor is  100,000 Ω

If you want to learn more, you can read:

https://brainly.com/question/74415

A mechanic claims to have developed a car engine that runs on water instead of gasoline. What is your response to this claim?​

Answers

The claim will be impractical. The reason behind this is provided below throughout the explanation segment.

Inside the same combustion chamber, fresh water can't be pressurized even more than fuel as well as air. Consequently, the cylinder does not burn due to a problem with the compressor.To accomplish the development processes, a machine requires any sort of combustible which might cause combustion as well as create a tremendous quantity of power.

Thus, the idea of using water instead of petroleum appears unworkable throughout traditional engines.

Learn more:

https://brainly.com/question/4067583

if a person is injured at the hospital during a natural disaster a correct action to take is ​

Answers

first check that you and the casualty aren't in any danger. If you are, make the situation safe. When it's safe to do so, assess the casualty and, if necessary, dial 999 or 112 for an ambulance. You can then carry out basic first aid and shift to another hospital




That’s what I learnt sooo..

hỗ trợ mình với được không các bạn

Answers

Answer:

Explanation:

Be bop

số bit của pic 16f887

Answers

Answer:

what does it mean

Explanation:

sorry

plz write in English

You are given a pot of hot tea (350 mL) at a temperature of 85°C and a quantity of ice at -12°C. Determine the absolute minimum amount of ice you can add to the hot tea so that at equilibrium you have iced tea (ie. a very, very small amount of ice and some water). You can assume tea has the same density (1.00 g/mL) and specific heat (4190 J/kgK) as liquid water. The heat of fusion of H2O is 3.33x10^5 J/kg. The specific heat of ice is 2090 J/kgK.

Answers

Answer:

348 g

Explanation:

The heat gained by the ice equals the heat lost by the hot tea.

Also, since we require a very, very small amount of ice and some water, to still have some ice, the temperature of the hot tea has to decrease to the melting point of ice which is 0°C. So, the final temperature of the mixture is 0 °C.

So, mc(T - T') + mL = -MC(T - T") where m = mass of ice, c =  specific heat of ice = 2090 J/kgK., T = final temperature of mixture = 0 °C, T' = initial temperature of ice = -12 °C, L = heat of fusion of H2O = 3.33 × 10⁵ J/kg, M = mass of hot tea = ρV where ρ = density of tea = 1.00 g/mL and V = volume of hot tea = 350 mL. So, M = ρV = 1.00 g/mL × 350 mL = 350 g = 0.350 kg, C = specific heat of tea = 4190 J/kgK and T" = initial temperature of tea = 85 °C.

Making m subject of the formula, we have

mc(T - T') + mL = -MC(T - T")

m[c(T - T') + L] = -MC(T - T")  

m = -MC(T - T")/[c(T - T') + L]

substituting the values of the variables into the equation, we have

m = -MC(T - T")/[c(T - T') + L]

m = -0.350 kg × 4190 J/kgK(0 °C - 85 °C.)/[2090 J/kgK(0 °C. - (-12 °C)) + 3.33 × 10⁵ J/kg]

m = -1466.5 J/kK(- 85 °C)/[2090 J/kgK(0 °C + 12 °C)) + 3.33 × 10⁵ J/kg]

m = 124652.5 J/[2090 J/kgK(12 °C) + 3.33 × 10⁵ J/kg]

m = 124652.5 J/[25080 J/kg + 3.33 × 10⁵ J/kg]

m = 124652.5 J/358080 J/kg

m = 0.3481 kg

m = 348.1 g

m ≅ 348 g

So, the minimum amount of ice to be added is 348 g.

Explain the 11 sections that a typical bill of quantity is divided into​

Answers

Answer:

The main sections included in the bill of quantities are Form of Tender, Information, Requirements, Pricing schedule, Provisional sums, and Day works.

what does mean setbacks with MRT station?

Answers

The term “setback” refers to the distance (measured in feet) a house or structure must be from the front, side and rear property lines. Setbacks allow for access to underground utilities and distance between properties.

Uses of P-N junction

Answers

Answer:

Explanation:

Two that come to mind:

a semiconductor diode is essentially a PN junctiona transistor is made of two pn junctions.

Cho biết tác dụng chung của các hệ giằng khung ngang nhà công nghiệp nhẹ 1 tầng 1 nhịp.

Answers

I don’t know how to speak the laungue or know this language

If a corporation is socially responsible, it will develop and implement a sustainability plan and communicate it to stakeholders.

True
False

Answers

Answer:

True

Explanation:

All big companies are pretty much required in today's day and ages to complete these reports whether they truly believe it.

Why is logging done during drilling?

Answers

Answer:

Logging while drilling (LWD) is a technique of conveying well logging tools into the well borehole downhole as part of the bottom hole assembly (BHA). ... In these situations, the LWD measurement ensures that some measurement of the subsurface is captured in the event that wireline operations are not possible

Other Questions
For all the years I knew my grandma, she could barely see. Grandma was legally blind, and yet she knew, by feel, the location of every dish in her kitchen and every work of literature on the bookcase in the living room. I remember especially the bird-like way she peered at things. I'd bring her a copy of my latest school picture, and she'd hold the photo an inch or two from her face, tilt her head to one side, and inspect it before saying, "Very pretty." I used to think she was just being polite, that she really couldn't see me in the picture. But then she'd add, "That pin you're wearing was your mother's." How did she see that little blur on my jacket? The things she could see never failed to amaze me. Watching television with Grandma, I never failed to learn something. Usually it was the complicated plot twist of one of her favorite soap operasThe Guiding Light or As the World Turns. We grandkids would curl up on the big couch while Grandma pulled up a footstool and planted herself right next to the TV, elbows on her knees, to watch the screen. At the commercial break, she'd explain who was marrying whom and who was in the hospital and who had recently come back from the dead. She seemed to have no trouble identifying the characters whom she could barely see. Whether or not she could bring them into sharp focus, they were as real to her as her giggling grandkids. For a treat, we'd sometimes pile into our grandparent's black car for a drive around town: my grandfather at the wheel, my long-legged older brother in the front seat, and Grandma sandwiched between me and my little brother in the backbut sitting so far forward she was practically in the front. I'd imagined all she could see was a blur of images rushing past, yet she could always tell when Grandpa had missed a turn or forgotten to turn on his headlights. Returning home, Grandma would wave at the boy who mowed their lawn and point out the new fruit on the plum tree in their yard. In later years, when I visited from college, Grandma would always be waiting when I pulled up in my old orange car (that's admittedly hard to miss, no matter how bad one's vision). She'd greet me with a bear hug. Then she'd surprise me, every time, with what she could see. Holding my face in her hands, she'd turn my head from side to side and announce, "You got your hair cut!" as if I had won the lottery and forgotten to tell her. I began to wonder if we rely on our eyes too muchif maybe, with our perfect sight, we're actually missing the details my grandma and her poor vision never failed to catch.This story makes the reader think about what we can and cannot see. What question does the author ask us to think about at the end? A. Was life just a blur of images racing past our eyes? B. Could Grandma see the things she said she could see? C. Do people with perfect vision miss out on the details of life? D. Do blind people enjoy life more than people who can see? Which equation can be solved using the one-to-one property?3X = 104In x = 2 log x = 54* = 47x+2 Briefly summarize the arguments for and against animal experimentation? What is Legal Process of Khula in Pakistan what is the area of the figure below? Simplify the following expression:(15b^5)^2-(5b^2)^3 what is the full form of ATP? She...be at home .I saw her scooter in front of her house .put the correct model verb What is the slope-intercept equation of the line below? Find the length of the segment indicated. circles 4 The most significant event of the Roman period was the birth,life,and death of Jesus Christi In the equation 11 - 4(x +4) = 6x, the first step is to simplify 11 - 4.TrueFalse Please help me I will make brain list Yesenia drove 45.3 miles on Monday and 3.8miles more on Tuesday. How many miles did shedrive in all? Indian historians believe that chalukyas were _____ please help with this on the picture Help ASAP I need answer soon as possible A. Rearrange the words in the following sentences to make sens1. Of ice cream are fond children.Ice Cream2.Good to cook is because it helps us fire.3.Like another he will John where friend find?4.The look wall on at the shadowSocks up his told was to pull hehe was fold to pull his Sices The entrance ticket for a carnival costs $89.97, which includes a royal mealthat costs $10.85, 1 play station game, and 3 water rides (Each water ridecosts the same price). The cost of a water ride is twice as that of a playstation game. Find the cost of a water ride. Estimate to the nearest tenths. If an object has a mass of 200kg but its Ke is 40J, what is its speed?