Answer:
Explanation:
How much force is acting on a certain area
A load of 25 kg is applied to the lower end and of a steal wire of length 25 m and thickness 3.0mm .The other end of wire is suspeded from a rigid support calculate strain and stress produced in the wire
Answer:
the weight of the wire + 25kg
Explanation:
the rate of cooling determines ....... and ......
Answer:
freezing point and melting point
4. A diver is 20 m underwater and they are startled by a shark. They are tempted to take a big breath of air, drop their gear, and swim to the surface while holding their breath. Explain why this is dangerous g
Answer:
Explanation:
The air enters their lungs at the same pressure as the water at that depth.
If they hold their breath as they rise to atmospheric pressure, the expanding volume of air (due to decreasing pressure) trapped in their lungs will hyperextend the alveoli in their lungs, likely tearing blood lines and risking death by drowning in their own blood.
ASK YOUR TEACHER An oil slick on water is 99.8 nm thick and illuminated by white light incident perpendicular to its surface. What color does the oil appear (what is the most constructively reflected wavelength, in nanometers), given its index of refraction is 1.38
Answer:
There will be a phase change at the 1-1.38 interface and no phase change at the 1.38-1.33 interface.
At a thickness of lambda / 4 (y/4) one should get constructive interference for the reflected light.
y = 4 * 99.8 * 10E-9 m = 400 nm (about) = 4 * 10E-7 m
The color of this light will be violet or blue
The first law of motion describes the principle of __________
Answer:
The first law of motion describes the principle of law of inertia.
If a marathon runner runs 9.5 miles in one direction, 8.89 miles in another direction, and 2.333 miles in a third direction, how much distance did the runner run?
We have that the total distance covered by the runner is
[tex]d_t=20.723miles[/tex]
The total distance covered by the runner is a sum of all miles covered by the runner
Therefore
With
[tex]d_t[/tex]=Total distance
[tex]d_t=d_1+d_2+d_3\\\\d_t=9.5+8.89+2.333[/tex]
[tex]d_t=20.723miles[/tex]
in conclusion
The total distance covered by the runner is
[tex]d_t=20.723miles[/tex]
For more information on this visit
https://brainly.com/question/12319416
A block with a mass of 0.26 kg is attached to a horizontal spring. The block is pulled back from its equilibrium position until the spring exerts a force of 1.2 N on the block. When the block is released, it oscillates with a frequency of 1.4 Hz. How far was the block pulled back before being released?
Answer:
2
Explanation:
pulling force because of it force
Answer:
5.9 cm
Explanation:
f: frequency of oscillation
frequency of oscillationk: spring constant
frequency of oscillationk: spring constantm: the mass
[tex]f = \frac{1}{2\pi} \sqrt{ \frac{k}{m} } [/tex]
in this problem we know,
F= 1.4 Hz
m= 0.26 kg
By re-arranging the formula we get
[tex]k = {(2\pi \: f )}^{2} m = {(2\pi(1.4hz))}^{2} 0.26kg = 20.1 \frac{n}{m} [/tex]
The restoring force of the spring is:
F= kx
where
F= 1.2 N
k= 20.1 N/m
x: the displacement of the block
[tex]x = \frac{f}{k} = \frac{1.2 \: n}{20.1 \frac{n}{m} } = 0.059m \: = 5.9 \: cm[/tex]
Consider a box with two gases separated by an impermeable membrane. The membrane can move back and forth, but the gases cannot penetrate the membrane. The left side is filled with gas A and the right side is filled with gas B. We will assume that equipartition applies to both gases, but gas A has an excluded volume due to large molecules so its entropy has a different formula.
SA=NAkln(VA+ bNA)+f(UA,NA)
SB=NBkln(VB)+f(UB,NB)
Required:
If NA= 1 moles, NB = 2 moles, the total volume of the box is 1 m3, and b= 4 × 10-4 m3/mole, then find the equilibrium value of VA by maximizing the total entropy.
Answer:
The answer is "[tex]0.3336\ m^3[/tex]"
Explanation:
Using the Promideal gas law:
[tex]P_A=P_B\\\\P_A(V_A-\eta_A b)= \eta_A RT......(1)\\\\P_B V_B=\eta_B \bar{R}T........(2)\\\\From (1) \zeta (2)\\\\[/tex]
[tex]\frac{\eta_A}{V_A-\eta_A b}=\frac{\eta B}{V B}\\\\ \frac{V A- \eta_A b}{V B}=\frac{\eta A}{\eta B }\\\\ \frac{V A-b}{V B}=\frac{1}{2}\\\\V A+V B=1\\\\V B =1- V A\\\\\frac{V A-b}{1-V A}=\frac{1}{2}\\\\2V A-2b=1-V A\\\\3 V A=1+2b\\\\V A=\frac{1+2b}{3}\\\\[/tex]
[tex]=\frac{1+2(4\times 10^{-4})}{3}\\\\=0.3336\ m^3[/tex]
The equilibrium value of Va is 0.3336 m³.
Ideal gas lawThe equilibrium value of Va is determine by applying ideal gas law as shown below;
Pressure of gas A = Pressure of gas B
Pa = Pb
Pa(Va - nab) = naRT----(1)
PbVb = nbRT -----(2)
Solve equation (1) and (2)
[tex]\frac{P_b}{RT} = \frac{n_b}{V_b} \\\\\frac{P_b}{P_a(V_a- n_ab)/n_a} = \frac{n_b}{V_b}\\\\\frac{n_a}{V_a - n_ab} = \frac{n_b}{V_b} \\\\\frac{V_a - n_ab}{V_b} = \frac{n_a}{n_b} \\\\\frac{V_a - b}{V_b} = \frac{1}{2}[/tex]
Va + Vb = 1
Vb = 1 - Va
[tex]\frac{V_a - b}{1 - V_a} = \frac{1}{2}[/tex]
2Va - 2b = 1 - Va
3Va = 1 + 2b
[tex]V_ a = \frac{1 + 2b}{3} \\\\V_a = \frac{1 + (2 \times 4\times 10^{-4})}{3} \\\\V_a = 0.3336 \ m^3[/tex]
Thus, the equilibrium value of Va is 0.3336 m³.
Learn more about equilibrium value here: https://brainly.com/question/22569960
Ashley, a psychology major, remarks that she has become interested in the study of intelligence. In other words, Ashley is interested in?
Group of answer choices.
a) the capacity to learn from experience, solve problems, and to adapt to new situations.
b) how behavior changes as a result of experience.
c) the factors directing behavior toward a goal.
d) the ability to generate novel
Answer:
a) the capacity to understand the world, think rationally, and use resources effectively.
Explanation:
Psychology can be defined as the scientific study of both the consciousness and unconsciousness of the human mind such as feelings, emotions and thoughts, so as to understand how it functions and affect human behaviors in contextual terms.
This ultimately implies that, psychology focuses on studying behaviors and the mind that controls it.
In this scenario, Ashley who is a psychology major, stated that she's interested in the study of intelligence.
Intelligence can be defined as a measure of the ability of an individual to think, learn, proffer solutions to day-to-day life problems and effectively make informed decisions.
In other words, Ashley is interested in the capacity of humans to understand the world, think rationally, and use resources effectively to produce goods and services that meet the unending requirements, needs or wants of the people (consumers or end users) living around the world.
two objects A and B vertically thrown up with velocities 80m/s and 100m/s at two sec interval.where and when will they meet each other?
Answer:
hcbvdgsyyvjusvbxjxu usbsbhsi
Explanation:
ysggsghxuxgscsixigdvgsibxhdhshshjf
MULTIPLE CHOICE
What is the role of the Sun in a forest ecosystem?
What is the Role of the sun in a forest ecosystem?
Answer:
It is to produce sunlight in the forest plants
A kind of variable that a researcher purposely changes in investigation is
Answer:
independent variable
Explanation:
i don't understand this, can someone help please??
Explanation:
N2 + H2 --> NH3
balance them:
N2 + 3 H2 --> 2 NH3
so if 6 moles of N2 react, 12 moles of NH3 will form.
(you have to look at the big number in front, in this case its N2 and 2 NH3, therefore the amount of N2 will produce double the amount of NH3 )
tìm thời điểm vật đạt tốc độ 25\pi cm/s lần thứ 2021
Answer:
una ufx vek cintos kavres millianto
Explanation:
vekas moriqn5o siveria il a ola ola micanese ma n8 aou ko sevyaera
A parallel plate capacitor is constructed using two square metal sheets, each of side L = 10 cm. The plates are separated by a distance d = 2 mm and a voltage applied between the plates. The electric field strength within the plates is E = 4000 V/m. The energy stored in the capacitor is
Answer:
The energy stored is 1.4 x 10^-9 J.
Explanation:
Side of square, L = 10 cm = 0.1 m
Distance, d = 2 mm = 0.002 m
Electric field, E = 4000 V/m
The energy stored in the capacitor is
[tex]U = 0.5 C V^2[/tex]
The capacitance is given by
[tex]C = \frac{\varepsilon o A}{d}\\\\So \\\\U = 0.5\frac{\varepsilon o A}{d}\times E^2 d^2\\\\U = 0.5\times 8.85\times 10^{-12}\times 0.1\times 0.1\times 4000\times 4000\times 0.002\\\\U = 1.4\times10^{-9} J[/tex]
What is the maximum speed at which a car can round a curve of 25-m radius on a level road if the coefficient of static friction between the tires and road is 0.80?
I assume the curve is flat and not banked. A car making a turn on the curve has 3 forces acting on it:
• its weight, mg, pulling it downward
• the normal force from contact with the road, n, pushing upward
• static friction, f = µn, directed toward the center of the curve (where µ is the coefficient of static friction)
By Newton's second law, the net forces on the car in either the vertical or horizontal directions are
∑ F (vertical) = n - mg = 0
∑ F (horizontal) = f = ma
where a is the car's centripetal acceleration, given by
a = v ²/r
and where v is the maximum speed you want to find and r = 25 m.
From the first equation, we have n = mg, and so f = µmg. Then in the second equation, we have
µmg = mv ²/r ==> v ² = µgr ==> v = √(µgr )
So the maximum speed at which the car can make the turn without sliding off the road is
v = √(0.80 (9.80 m/s²) (25 m)) = 14 m/s
Two forces are acting on a body. One acts east, the other at 35° north of east. If the
two forces are equal in magnitude of 50 N, find the resultant using the Law of Sines
and the Law of Cosines. Please answer with full solution. Thanks
A=B=50NAngle=theta=35°
We know
[tex]\boxed{\sf R=\sqrt{A^2+B^2+2ABcos\Theta}}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{50^2+50^2+2(50)(50)cos35}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{2500+2500+2(2500)\times (-0.9)}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{5000+5000(-0.9)}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{5000+(-4500)}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{5000-4500}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{-500}[/tex]
[tex]\\ \sf\longmapsto R=22.4i[/tex]
Resultant using the Law of Sines and the Law of Cosines will be R=95 N
What is force?Force is an external agent applied on any object to displace it from its position. Force is a vector quantity, so with magnitude it also requires direction. Direction is necessary to examine the effect of the force and to find the equilibrium of the force.
The Magnitude of two forces =50 N
Angle between the forces = 35
By using the resultant formula
[tex]\rm R=\sqrt{A^2+B^2+2ABCos\theta}[/tex]
[tex]\rm R=\sqrt{50^2+50^2+2(50)(50)Cos35}[/tex]
[tex]\rm R=\sqrt{5000+5000(0.81)}[/tex]
[tex]\rm R=\sqrt{5000+4500}[/tex]
[tex]\rm R=95\ N[/tex]
Hence the Resultant using the Law of Sines and the Law of Cosines will be R=95 N
To know more about force follow
https://brainly.com/question/25239010
What happens to the temperature of matter as distance is increased? Explain why.
Answer:
The tempature of the matter increases.
Explanation:
The matter is heated by friction, weather that is through the air or if its touching the ground like a car.
please mark me as brainliest of this is right, thanks
The kinetic energy of a particle of mass 500g is 4.8j. Determine the velocity of the particle
Answer:
4.38 m/s
Explanation:
A motor is designed to operate on 117 V and draws a current of 17.7 A when it first starts up. At its normal operating speed, the motor draws a current of 2.78 A. Obtain (a) the resistance of the armature coil, (b) the back emf developed at normal speed, and (c) the current drawn by the motor at one-third normal speed.
Answer:
Resistance of the armature coil = 6.61 ohms
Back emf developed at normal speed = 98.62 V (Approx.)
Current drawn by the motor at one-third normal speed = 12.73 A
Explanation:
Given:
Potential difference V = 117 V
Current = 17.7 A
Motor drawn current = 2.78 A
Find:
Resistance of the armature coil
Back emf developed at normal speed
Current drawn by the motor at one-third normal speed
Computation:
A] Resistance of the armature coil R = V/ I
Resistance of the armature coil = 117 / 17.7
Resistance of the armature coil = 6.61 ohms
B] Back emf developed at normal speed = V- IR
Back emf developed at normal speed = 117 V - (2.78 A)(6.61 ohms)
Back emf developed at normal speed = 117 V - 18.37
Back emf developed at normal speed = 98.62 V (Approx.)
C] Current drawn by the motor at one-third normal speed = 17.7 A - (98.62/3)/(6.61 ohms)
Current drawn by the motor at one-third normal speed = 17.7 - 4.97
Current drawn by the motor at one-third normal speed = 12.73 A
Proper physical exercise makes bones _[blank 1]_.
People with stronger muscles and bones have better _[blank 2]_.
Which option shows the words that correctly fill in blank 1 and blank 2, in that order?
longer, flexibilitylonger, flexibility , ,
stronger, posturestronger, posture , ,
longer, posturelonger, posture , ,
stronger, flexibility
stronger, posturestronger, posture
hope that helped
A steel cable with Cross Sectional Area 3.00cm² has an elastic limit of 2.40 x 10^8pascals. Find the maximum upward acceleration that can be given a 1200kg elevated supported by the cable if the stress is not to exceed one-third of the elastic limit.
Answer:
Stress = F / A force per unit area
A = 3.00 cm^2 = 3 E-4 m^2
F = 2.4E8 N/m^2 * 3E-4 m^2 = 7.2E4 N max force applied
F/3 = 2.4E4 N if force not to exceed limit (= f)
f = M a
a = 2.4 E4 N / 1.2 E3 kg = 20 m / s^2 about 2 g
Partial tides _______. Question 7 options: represent various components of local tides that are resolved mathematically are predicted individually are added together to predict the height and timing of astronomical tides All of the above are correct. Only a and c are correct.
Complete Question
Partial tides __________.
Question 7 options:
a. represent various components of local tides that are resolved mathematically
b. are added together to predict the height and timing of astronomical tides
c. consist of 4 components due to the influence of celestial bodies
d. consist of up to 60 components due to astronomical and non-astronomical factors
e. All of the above except c are correct.
Answer:
Option E
Explanation:
Generally
Partial tides represent various components of local tides that are resolved mathematically
Partial tides are added together to predict the height and timing of astronomical tides
Partial tides consist of up to 60 components due to astronomical and non-astronomical factors
But Partial tides do not consist of 4 components due to the influence of celestial bodies
Therefore
All of the above except c are correct.
Option E
A capacitor consists of two metal surfaces separated by an electrical insulator with no electrically conductive path through it. Why does a current flow in a resistor-capacitor circuit when the switch is closed?
Answer:
Displacement current flows in the dielectric material(insulated region)
Explanation:
Firstly a capacitor stores charge when a capacitor is charging (or discharging), current flows in the circuit. Also, there is no charge transfer in the dielectric material in the capacitor which is contradictory to the flow of current. Hence, displacement current is the current in the insulated region due to the changing electric flux.
What is a measure of how hard it is to stop a moving object?
25.
A. gravity
B. weight
C.
inertia
D. momentum
Answer:
C. inertia
Explanation:
inertia describes an object’s resistance to change in motion (or to get in motion due to a lack of motion), and momentum describes how much motion it has.
both are connected, as inertia depends on the object's momentum, but the answer here is inertia.
What is the incorrect statement regarding the isotopes of the same element?
1) Electronic configuration is equal
2) Mass number is equal
3) Number of protons are equal
4) Number of electrons are equal
Answer:
1231
Explanation:
Can Some1 help??
When using the "ball and stick" drawing method of drawing a compound, which element usually goes in the center of the model?
The propeller on a boat motor is initially rotating at 8 revolutions per second. As the boat captain reduces the boat speed, the propeller SLOWS at a steady rate of 0.9 revolutions per second per second. After 17 revolutions, how fast is the propeller spinning in revolutions per second
Answer: [tex]5.77\ rps[/tex]
Explanation:
Given
Initial angular velocity is [tex]\omega_i=8\ rps[/tex]
rate of reduction [tex]\alpha=0.9 rev/s^2[/tex]
after 17 revolution i.e. [tex]\theta =17\ rev[/tex]
using [tex]\Rightarrow \omega_f^2-\omega_i^2=2\alpha\theta[/tex]
Insert the values
[tex]\Rightarrow \omega_f^2=8^2-2\times (0.9)\times17\\\Rightarrow \omega_f^2=33.4\\\Rightarrow \omega_f=5.77\ rps[/tex]
Why we use semiconductor instead of metal in thermopile.
Answer:
Semiconductors are not normal materials. They have special properties which conductors/metals cannot exhibit. The main reason for the behavior of semiconductors is that they have paired charge carriers-the electron-hole pair. This is not available in metals.
Determine the acceleration of a pendulum bob as it passes through an angle of 15 degrees to the right of the equilibrium point.
Answer:
Explanation:
Since energy is conserved:
2
mu
2
=
2
mv
2
+mgh
⇒u
2
=v
2
+2gh
⇒(3)
2
=v
2
+2(9.8)(0.5−0.5cos60)
⇒v=2m/s
Acceleration of the simple pendulum is 2.62 m/s².
What is meant by a simple pendulum ?When a point mass is suspended from a fixed support by a light, non-extensible string, the instrument is said to be a simple pendulum.
Here,
Let the mass of the bob be m. The simple pendulum is attached to the fixed support with a string having length l. The pendulum makes an angle of 15° with the vertical from the equilibrium point.
Let T be the tension acting on the string.
As, the bob passes through the angle,
The weight of the bob becomes equal to the vertical component of the tension.
mg = T cos15°
Also, the horizontal component of the tension,
T sin15° = ma
By solving these two equations, we get that,
Acceleration of the simple pendulum,
a = g tan15°
a = 9.8 x 0.267
a = 2.62 m/s²
Hence,
Acceleration of the simple pendulum is 2.62 m/s².
To learn more about simple pendulum, click:
https://brainly.com/question/31816771
#SPJ3
