80 grams of iron at 100°C is dropped into 200 of water at 20°C contained in an iron vessel of mass 50 gram find the resulting temperature.​

Answers

Answer 1

Answer:

the resulting temperature is 23.37 ⁰C

Explanation:

Given;

mass of the iron, m₁ = 80 g = 0.08 kg

mass of the water, m₂ = 200 g = 0.2 kg

mass of the iron vessel, m₃ = 50 g = 0.05 kg

initial temperature of the iron, t₁ = 100 ⁰C

initial temperature of the water, t₂ = 20 ⁰C

specific heat capacity of iron, c₁ = 462 J/kg⁰C

specific heat capacity of water, c₂ = 4,200 J/kg⁰C

let the temperature of the resulting mixture = T

Apply the principle of conservation of energy;

heat lost by the hot iron = heat gained by the water

[tex]m_1c_1 \Delta t_1 = m_2c_2\Delta t_2\\\\m_1c_1 (100 - T) = m_2c_2 (T- 20)\\\\0.08 \times 462 (100-T) = 0.2 \times 4,200 (T-20)\\\\36.96 (100-T) = 840 (T-20) \\\\100 - T = 22.72 (T-20)\\\\100-T = 22.72 T - 454.4 \\\\554.4 = 23.72T\\\\T = \frac{554.4}{23.72} \\\\T = 23.37 \ ^0C[/tex]

Therefore, the resulting temperature is 23.37 ⁰C


Related Questions

what effect does the force of gravity have on a stone thrown vertically upwards​

Answers

Answer:

rock go down

Explanation:

what comes up must come down.

A projectile is fired into the air from the top of a 200-m cliff above a valley as shown below. Its initial velocity is 60 m/s at 60° above the horizontal. Calculate (a) the maximum height, (b) the time required to reach its highest point, (c) the total time of flight, (d) the components of its velocity just before striking the ground, and (e) the horizontal distance traveled from the base of the cliff.​

Answers

a) y(max)  = 337.76 m

b) t₁ = 5.30 s  the time for y maximum

c)t₂ =  13.60 s  time for y = 0 time when the fly finish

d) vₓ = 30 m/s        vy = - 81.32 m/s

e)x = 408 m

Equations for projectile motion:

v₀ₓ = v₀ * cosα          v₀ₓ = 60*(1/2)     v₀ₓ = 30 m/s   ( constant )

v₀y = v₀ * sinα           v₀y = 60*(√3/2)     v₀y = 30*√3  m/s

a) Maximum height:

The following equation describes the motion in y coordinates

y  =  y₀ + v₀y*t - (1/2)*g*t²      (1)

To find h(max), we need to calculate t₁ ( time for h maximum)

we take derivative on both sides of the equation

dy/dt  = v₀y  - g*t

dy/dt  = 0           v₀y  - g*t₁  = 0    t₁ = v₀y/g

v₀y = 60*sin60°  = 60*√3/2  = 30*√3

g = 9.8 m/s²

t₁ = 5.30 s  the time for y maximum

And y maximum is obtained from the substitution of t₁  in equation (1)

y (max) = 200 + 30*√3 * (5.30)  - (1/2)*9.8*(5.3)²

y (max) = 200 + 275.40 - 137.64

y(max)  = 337.76 m

Total time of flying (t₂)  is when coordinate y = 0

y = 0 = y₀  + v₀y*t₂ - (1/2)* g*t₂²

0 = 200 + 30*√3*t₂  - 4.9*t₂²            4.9 t₂² - 51.96*t₂ - 200 = 0

The above equation is a second-degree equation, solving for  t₂

t =  [51.96 ±√ (51.96)² + 4*4.9*200]/9.8

t =  [51.96 ±√2700 + 3920]/9.8

t =  [51.96 ± 81.36]/9.8

t = 51.96 - 81.36)/9.8         we dismiss this solution ( negative time)

t₂ =  13.60 s  time for y = 0 time when the fly finish

The components of the velocity just before striking the ground are:

vₓ = v₀ *cos60°       vₓ = 30 m/s  as we said before v₀ₓ is constant

vy = v₀y - g *t        vy = 30*√3  - 9.8 * (13.60)

vy = 51.96 - 133.28         vy = - 81.32 m/s

The sign minus means that vy  change direction

Finally the horizontal distance is:

x = vₓ * t

x = 30 * 13.60  m

x = 408 m


The temperature of a body falls from 30°C to 20°C in 5 minutes. The air
temperature is 13°C. Find the temperature after a further 5 minutes.

Answers

Answer:

15.88

is the correct answer

Susan is quite nearsighted; without her glasses, her far point is 34 cm and her near point is 17 cm . Her glasses allow her to view distant objects with her eye relaxed. With her glasses on, what is the closest object on which she can focus?

Answers

Answer:

[tex]u=34cm[/tex]

Explanation:

From the question we are told that:

Far point is [tex]V=34 cm[/tex]

Near point is [tex]u=17 cm[/tex]

Therefore

Focal Length

[tex]f=-34cm[/tex]

Generally the equation for the Lens is mathematically given by

[tex]\frac{1}{u}=\frac{1}{f}-\frac{1}{v}[/tex]

[tex]\frac{1}{u}=\frac{1}{-34}-\frac{1}{-17}[/tex]

[tex]u=34cm[/tex]

A car is traveling at 118 km/h when the driver sees an accident 85 m ahead and slams on the brakes. What minimum constant deceleration is required to stop the car in time to avoid a pileup

Answers

Answer:

The constant minimum deceleration required to stop the car in time to avoid pileup is 6.32 m/s²

Explanation:

From the question, the car is traveling at 118 km/h, that is the initial velocity, u = 118km/h

The distance between the car and the accident at the moment when the driver sees the accident is 85 m, that is s = 85 ,

Since the driver slams on the brakes and the car will come to a stop, then the final velocity, v = 0 km/h = 0 m/s

First, convert 118 km/h to m/s

118 km/h = (118 × 1000) /3600 = 32.7778 m/s

∴ u = 32.7778 m/s

Now, to determine the deceleration, a, required to stop,

From one of the equations of motion for linear motion,

v² = u² + 2as

Then

0² = (32.7778)² + 2×a×85

0 = 1074.3841 + 170a

∴ 170a = - 1074.3841

a = - 1074.3841 / 170

a = - 6.3199

a ≅ - 6.32 m/s²

Hence, the constant minimum deceleration required to stop the car in time to avoid pileup is 6.32 m/s²

May someone help...please. Pretty please...

If a person is 18 % shorter than average, what is the ratio of his walking pace (that is, the frequency 'f' of his motion) to the walking pace of a person of average height? Assume that a person's leg swings like a pendulum and that the angular amplitude of everybody's stride is about the same.
f(short)/f(avg)=?

Answers

We have that  the ratio of his walking pace  to the walking pace of a person of average height is

[tex]\frac{V_2}{V_1}=1.10[/tex]

given the assumption and the calculation given below

From the question we are told that:

Consider a person 18\% shorter than average

Let average height of a person be [tex]10m[/tex]

Therefore

The height of an [tex]18\%[/tex] shorter man is mathematically given as

H=10*0.18

H=8.2m

Generally, the equation for velocity is mathematically given by

[tex]v=\frac{1}{2\pi} \sqrt{{g}{l}}[/tex]

Where we have the  Assumption that a person's leg swings like a pendulum and that the angular amplitude of everybody's stride is about the same

Therefore

[tex]\frac{V_1}{V_2}=\frac{l_1}{l_2}[/tex]

[tex]\frac{V_1}{V_2}={82}{100}[/tex]

[tex]\frac{V_2}{V_1}=1.10[/tex]

In conclusion

The ratio of his walking pace (that is, the frequency 'f' of his motion) to the walking pace of a person of average height is

[tex]\frac{V_2}{V_1}=1.10[/tex]

For more information on this visit

https://brainly.com/question/21196186

an alternating voltage of 100V, 50HZ Is Applied across an impedance of (20-j30) calculate the resistance, the capacitance, current, the phase angle between current and voltage

Answers

The resistance R = 20 Ω

The capacitance C = 106.1 μF

The current, I is 2.773 A at 56.31°.

The phase angle of the between the current and the voltage is 56.31° leading.

Since the impedance Z = 20 - j30 Ω, the resistance, R is the real part of the impedance. So R = ReZ = 20 Ω

So, the resistance R = 20 Ω

To find the capacitance, we need first to find the reactance of the capacitor X. Since the impedance Z = 20 - j30, the reactance of the capacitor X. is the imaginary part of the impedance. So X = ImZ = 30 Ω.

Now the reactance of the capacitor X = 1/ωC where ω = angular frequency of the circuit = 2πf where f = frequency of the circuit = 50 Hz and C = capacitance  

So, C = 1/ωX = 1/2πfX

Substituting the values of the variables into the equation, we have

C = 1/2πfX

C = 1/(2π × 50 Hz × 30 Ω)

C = 1/3000π

C = 1/9424.778

C = 1.061 × 10⁻⁴ F

C = 106.1 × 10⁻⁶ F

C = 106.1 μF

So, the capacitance is 106.1 μF

The current I = V/Z where V = voltage = 100 V at 0° and Z = impedance.

The magnitude of Z = √(20² + (-30)²)

= √(400 + 900)

= √1300

= 36.06 Ω

and its angle Φ = tan⁻¹(ImZ/ReZ)

= tan⁻¹(-30/20)

= tan⁻¹(-1.5) = -56.31°

So, V = 100 ∠ 0° and Z = 36.06 ∠ -56.31°

So, the current, I = V/Z =  (100 ∠ 0°)/36.06 ∠ -56.31°

= 100/36.06 ∠(0° - (-56.31° ))

= 2.773 ∠ 56.31° A

So, the current is 2.773 A at 56.31°.

Since the current is 2.773 A at 56.31°, the phase angle of the between the current and the voltage is 56.31° leading.

So, the phase angle of the between the current and the voltage is 56.31° leading.

Learn more about alternating voltage here:

https://brainly.com/question/20345565

When a charged particle moves at an angle of 26.1 with respect to a magnetic field, it experiences a magnetic force of magnitude F. At what angle (less than 90o) with respect to this field will this particle, moving at the same speed?

Answers

Answer:

The angle is 153.9 degree.

Explanation:

Let the magnetic field is B and the charge is q. Angle = 26.1 degree

The force is F.

Let the angle is A'.

Now equate the magnetic forces

[tex]q v B sin 26.1 = q v B sin A'\\\\A' = 180 - 26.1 = 153.9[/tex]

: A fan is placed on a horizontal track and given a slight push toward an end stop 1.80 meters away. Immediately after the push, the fan of the cart engages and slows the cart with an acceleration of -0.45 m/s2. What is the maximum possible velocity (magnitude) the cart can have after the push so that the cart turns around just before it hits the end-stop

Answers

Answer:

The initial velocity is 1.27 m/s.

Explanation:

distance, s = 1.8 m

acceleration, a = - 0.45 m/s^2

final velocity, v = 0

let the initial velocity is u.

Use third equation of motion

[tex]v^2 = u^2 + 2 a s \\\\0 = u^2 - 2 \times 0.45\times 1.8\\\\u = 1.27 m/s[/tex]

We have that the Initial velocity  is mathematically given as

u=1.27m/s

Maximum possible velocity

Question Parameters:

a slight push toward an end stop 1.80 meters away

he fan of the cart engages and slows the cart with an acceleration of -0.45 m/s2

Generally the equation for the  third equation of motion    is mathematically given as

Vf^2 = Vi^2 + 2ad

Therefore

0=u^2+0.45*1.8

u=1.27m/s

For more information on velocity visit

https://brainly.com/question/17617636

a bullet is dropped from the same height when another bullet is fired horizontally. they will hit the ground

Answers

Answer:

it will drop simultaneously

a stone is thrown vertically upwards with a velocity of 20 m per second determine the total time of flight of stone in air​

Answers

Answer:

Explanation:

The best way to do this is to remember the rule about the halfway mark in a parabolic path. At a trajectory's half way point in its travels, it will be at its max height. To get the total time in the air, we take that time at half way and double it. Here's what we know that we are told:

initial velocity is 20 m/s

Here's what we know that we are NOT told:

a = -9.8 m/s/s and

final velocity is 0 at an object's max height in parabolic motion.

We will use the equation:

[tex]v=v_0+at[/tex] where v is final velocity and v0 is initial velocity. Filling in:

0 = 20 + (-9.8)t and

-20 = -9.8t so

t = 2 seconds. The stone reaches its max height 2 seconds after it is thrown; that means that after another 2 seconds it will be on the ground. Total air time is 4 seconds.

HELP ME PLZ FAST
There is more than 1 answer,
The picture is down

Answers

Answer:

test her prototype and collect data about its flight

Your little sister (mass 25 kg) is sitting in her little red wagon (mass
8.5 kg) at rest. You begin pulling her forward, accelerating her with a
constant force for 2.35 s to a speed of 1.8 m/s. Calculate the impulse
you imparted to the wagon and its passenger.

Answers

Answer:

p = 60.6N*s

Explanation:

v_f = v_0+a*t

a = (v_f-v_0)/t

a = (1.8m/s)/2.35s

a = 0.77m/s²

F = m*a

F = (25kg+8.5kg)*0.77m/s²

F = 25.8N

^p = F*t

p = 25.8N*2.35s

p = 60.6N*s

2. What is the average speed of an athlete who runs 1500 m in 4 minutes?

Answers

Answer:

375 is the answer.

Explanation:

Speed : Distance / Time taken

S: m/ s

s: 1500/4

375 m / s answer

Answer:

375m per minute

Explanation:

if you are looking for a diffrent unit just multiply your answer by however many minutes are in that time frame

what is the major difference between the natural frequency and the damped frequency of oscillation.​

Answers

Answer:

This causes the amplitude of the oscillation to decay over time. The damped oscillation frequency does not equal the natural frequency. Damping causes the frequency of the damped oscillation to be slightly less than the natural frequency

A mass is hanging from the end of a horizontal bar that pivots around an axis through its center, but it is being held stationary. The bar is then released and begins to rotate. As the bar rotates from horizontal to vertical, the magnitude of the torque on the bar: ________

Answers

Answer:

The torque decreases because as the hanging mass goes down, the moment arm about the pivot point decreases. Since the torque is directly proportional to the length of the moment arm, torque decreases.

The torque decreases because as the hanging mass goes down, the moment arm about the pivot point decreases. Since the torque is directly proportional to the length of the moment arm, torque decreases.

What is the difference between atomic number and atomic mass ?

Atomic number of an element  is defined as total number of protons present in the nucleus,  neutrons carry no net electrical charge, so it is the charge number of the nucleus.

atomic mass of an element can be defined as the atomic weight is measured total mass of an element’s atom, the total number of neutrons and protons in the nucleus of an atom.

Both Atomic mass and an atomic number of elements are closely related if  atomic number is high, then the atomic mass is also said to be high.

For more details regarding fire mass , visit

brainly.com/question/16858932

#SPJ2

A train starts from rest (at position zero) and moves with constant acceleration. On the first observation, its velocity is 20m/s and 80seconds later the velocity became 60m/s. At 80s calculate the position, average velocity, and the constant acceleration over the interval.(7-points)

Answers

The value of the acceleration is a = 0.5 m/s². The position at 80 s is x = 3200 m and finally the average velocity is v = 40 m/s.

Acceleration:

We can use the fallowing kinematic equation to get the acceleration at 80 s.

[tex]a=\frac{v_{f}-v_{i}}{t}[/tex]            

Where:

v(i) is the initial velocity (20 m/s)v(f) is the final velocity (60 m/s)t is the interval (80 s)

The, we have:

[tex]\vec{a}=\frac{60-20}{80}[/tex]

[tex]\vec{a}=0.5\: m/s^{2}[/tex]

Position:

Knowing the acceleration we can find the position using the falling equation.

[tex]\vec{x}=v_{i}t+0.5at^{2}[/tex]

[tex]\vec{x}=20*80+0.5*0.5*80^{2}[/tex]

[tex]\vec{x}=3200 m[/tex]

Average velocity:

The definition of the average velocity is:

[tex]\vec{v}=\frac{\Delta x}{t}[/tex]

[tex]\vec{v}=\frac{x_{f}-x_{i}}{t}[/tex]

[tex]\vec{v}=\frac{3200-0}{80}[/tex]

[tex]\vec{v}=40\: m/s[/tex]

Learn more about the kinematic equations here:

https://brainly.com/question/13143668

I hope it helps you!

Light takes 1.2 sec to get from the moon to the Earth. Assume you are looking at the moon with noticeable earth shine. If the Sun burned out, you would eventually see the crescent of the moon disappear. The earth shine part of the moon would disappear Answer 2.4 s after the crescent disappeared.

Answers

Answer:

1.2 seconds

Explanation:

Answer to the following question is 1.2 seconds

Because light from the moon takes 1.2 seconds to reach Earth, the light released from the crescent immediately before it vanishes will also take 1.2 seconds to reach Earth. As a result, the earth-shine portion of the moon will vanish 1.2 seconds after the crescent has vanished.

14. What's one of the two requirements electric current?
A. There must be an electric potential between two bodies
B. There must be no valence electrons that make their element unstable
C. There must be a carbon element present in the electric current
D. There must be a magnetic force between two bodies
Marko

Answers

One of the two requirements of electric current is there must be an electric potential between two bodies

For electric current to flow, there must be an electric potential between two bodies.

This is because electric charge flows from a higher electric potential to a lower electric potential just as, water flows from a higher gravitational potential to a lower gravitational potential.

The difference between the electric potential between the two bodies causes the electric charge to flow between the two bodies.

This flow of electric charge constitutes electric current and electric current will only flow when there is an electric potential between two bodies.

So, one of the two requirements of electric current is there must be an electric potential between two bodies.

So, the answer is A

Learn more about electric current here:

https://brainly.com/question/13562393

If a conducting loop of radius 10 cm is onboard an instrument on Jupiter at 45 degree latitude, and is rotating with a frequency 2 rev/s; What is the maximum emf induced in this loop? If its resistance is 0.00336 ohms, how much current is induced in this loop? And what is the maximum power dissipated in the loop due to its rotation in Jupiter's magnetic field?

Answers

Answer:

a)  fem = - 2.1514 10⁻⁴ V,  b) I = - 64.0 10⁻³ A, c)    P = 1.38  10⁻⁶ W

Explanation:

This exercise is about Faraday's law

         fem = [tex]- \frac{ d \Phi_B}{dt}[/tex]

where the magnetic flux is

        Ф = B x A

the bold are vectors

        A = π r²

we assume that the angle between the magnetic field and the normal to the area is zero

         fem = - B π 2r dr/dt = - 2π B r v

linear and angular velocity are related

        v = w r

        w = 2π f

        v = 2π f r

we substitute

        fem = - 2π B r (2π f r)

        fem = -4π² B f r²

For the magnetic field of Jupiter we use the equatorial field B = 428 10⁻⁶T

we reduce the magnitudes to the SI system

       f = 2 rev / s (2π rad / 1 rev) = 4π Hz

we calculate

       fem = - 4π² 428 10⁻⁶ 4π 0.10²

       fem = - 16π³ 428 10⁻⁶ 0.010

       fem = - 2.1514 10⁻⁴ V

for the current let's use Ohm's law

        V = I R

        I = V / R

         I = -2.1514 10⁻⁴ / 0.00336

         I = - 64.0 10⁻³ A

Electric power is

        P = V I

        P = 2.1514 10⁻⁴ 64.0 10⁻³

        P = 1.38  10⁻⁶ W

A diffraction grating has 6000 lines per centimeter ruled on it. What is the angular separation (in degrees) between the second and the third orders on the same side of the central bright fringe when the grating is illuminated with a beam of light of wavelength 500 nm

Answers

Explanation:

Hope it Will help he hsuejwoamxgehanwpalasmbwfwfqoqlmdbehendalmZbgevzuxwllw. yeh we pabdvddxhspapalw. X

The angular separation (in degrees) between the second and the third orders on the same side of the central bright fringe if the wavelength is 500 nm and A diffraction grating has 6000 lines per centimeter ruled on it, is  27.29°.

What is diffraction?

Waves spreading outward around obstructions are known as diffraction. Sound, electromagnetic radiation like light, X-rays, and gamma rays, as well as very small moving particles like atoms, neutrons, and electrons that exhibit wavelike qualities all exhibit diffraction.

Given:

The number of lines = 6000 per cm,

The Wavelength, λ = 500 nm = 500 × 10 ⁻⁹ m

Calculate the diffraction grating,

[tex]d = 1 / no\ of\ lines[/tex]

d = 10⁻² / 6000 m,

Calculate the second-order maxima angle and third-order maxima angle by the formula given below,

[tex]dsin\theta_1 = n_1 \lambda[/tex]

[tex]sin\theta_1 = n_1\lambda / d[/tex]

[tex]\theta _1 = sin^{-1}[2\times 500\times 10 ^{-9}/10^{-2}\times 6000][/tex]

θ₁ = sin⁻¹(0.6)

θ₁ = 36.87°

Similarly, for θ₂,

θ₂ = sin⁻¹(3 × 500 × 10 ⁻⁹ / 10⁻² × 6000)

θ₂ = sin⁻¹(0.9)

θ₂ = 64.16°

Calculate the separation as follows,

θ₂ - θ₁ = 64.16° - 36.87°

θ₂ - θ₁ =  27.29°

Therefore, the angular separation (in degrees) between the second and the third orders on the same side of the central bright fringe if the wavelength is 500 nm and A diffraction grating has 6000 lines per centimeter ruled on it, is  27.29°.

To know more about diffraction:

https://brainly.com/question/12290582

#SPJ2

The voltage in an EBW operation is 45 kV. The beam current is 50 milliamp. The electron beam is focused on a circular area that is 0.50 mm in diameter. The heat transfer factor is 0.87. Calculate the average power density in the area in watt/mm2.

Answers

Answer:

[tex]P_d=6203.223062W/mm^2[/tex]

Explanation:

From the question we are told that:

Voltage [tex]V=45kV[/tex]

Current [tex]I=50mAmp[/tex]

Diameter  [tex]d=0.50mm[/tex]

Heat transfer factor [tex]\mu= 0.87.[/tex]

Generally the equation for  Power developed is mathematically given by

[tex]P=VI\\\\P=45*10^3*50*10^{-3}[/tex]

[tex]P=2.250[/tex]

Therefore

Power in area

[tex]P_a=1400*0.87[/tex]

[tex]P_a=1218watt[/tex]

Power Density

[tex]P_d=\frac{P_a}{Area}[/tex]

[tex]P_d=\frac{1218}{\pi(0.5^2/4)}[/tex]

[tex]P_d=6203.223062W/mm^2[/tex]

A 1050 kg car accelerates from 11.3 m/s to 26.2 m/s . What impulse does the engine give?

Answers

Answer:

I = 15,645. kg*m/s or 15,645 N*s

Explanation:

I = m(^v)

I = 1050kg((26.2m/s-11.3m/s)

I = 15,645. kg*m/s

Determine the magnitude as well as direction of the electric field at point A, shown in the above figure. Given the value of k = 8.99 × 1012N/C.

Answers

Answer:

Electric field at A = 9.28 x 10¹² N/C

Explanation:

Given:

K = 8.99 x 10¹² N/C

Missing information:

Length = 11 cm = 11 x 10⁻² m

q = 12.5 C

Find:

Electric field at A

Computation:

Electric field = Kq / r²

Electric field at A = [(8.99 x 10¹²)(12.5)] / [11 x 10⁻²]²

Electric field at A = 9.28 x 10¹² N/C

A mass is tired to spring and begins vibration periodically the distance between it's lowest position is 48cm what is the Amplitude of the vibration

Answers

Answer:

The amplitude of vibration of the spring is "24 cm"

The periodic vibrating body's motion follows a sinusoidal path. This sinusoidal path is illustrated in the attached picture.

From the picture, it can be clearly seen that the amplitude of the periodic vibration motion is the distance from its mean position to the highest point.

Since the distance of both the highest and the lowest points from the mean position is the same. Therefore, the distance between the lowest and the highest point must be equal to two times the amplitude of the wave.

Amplitude = 24 cm

Calculate the self-inductance (in mH) of a 45.0 cm long, 10.0 cm diameter solenoid having 1000 loops. mH (b) How much energy (in J) is stored in this inductor when 21.0 A of current flows through it? J (c) How fast (in s) can it be turned off if the induced emf cannot exceed 3.00 V? s

Answers

Answer:

(a) The self inductance, L = 21.95 mH

(b) The energy stored, E = 4.84 J

(c) the time, t = 0.154 s

Explanation:

(a) Self inductance is calculated as;

[tex]L = \frac{N^2 \mu_0 A}{l}[/tex]

where;

N is the number of turns = 1000 loops

μ is the permeability of free space = 4π x 10⁻⁷ H/m

l is the length of the inductor, = 45 cm = 0.45 m

A is the area of the inductor (given diameter = 10 cm = 0.1 m)

[tex]A = \pi r^2 = \frac{\pi d^2}{4} = \frac{\pi \times (0.1)^2}{4} = 0.00786 \ m^2[/tex]

[tex]L = \frac{(1000)^2 \times (4\pi \times 10^{-7}) \times (0.00786)}{0.45} \\\\L = 0.02195 \ H\\\\L = 21.95 \ mH[/tex]

(b) The energy stored in the inductor when 21 A current ;

[tex]E = \frac{1}{2}LI^2\\\\E = \frac{1}{2} \times (0.02195) \times (21) ^2\\\\E = 4.84 \ J[/tex]

(c) time it can be turned off if the induced emf cannot exceed 3.0 V;

[tex]emf = L \frac{\Delta I}{\Delta t} \\\\t = \frac{LI}{emf} \\\\t = \frac{0.02195 \times 21}{3} \\\\t = 0.154 \ s[/tex]

A sound wave made up of large number of unrelated frequencies superposted on each other is

Answers

Since the frequencies are unrelated, and there are a large number of them, I'll say this represents an example of noise.

Vặt nhỏ được ném lên từ điểm A trên mặt đất với vận tốc đầu 20m/s theo phương thẳng đứng. Xác định độ cao của điểm O mà vật đạt được. Bỏ qua ma sát

Answers

Explanation:

mặt đất với vận tốc ban đầu 20m/s. Bỏ qua mọi ma sát, lấy g = 10 m/s2. Độ cao cực đại mà vật đạt được là.

An object of mass 80 kg is released from rest from a boat into the water and allowed to sink. While gravity is pulling the object down, a buoyancy force of 1/50 times the weight of the object is pushing the object up (weight=mg). If we assume that water resistance exerts a force on the abject that is proportional to the velocity of the object, with proportionality constant 10 N-sec/m, find the equation of motion of the object. After how many seconds will the velocity of the object be 40 m/s? Assume that the acceleration due to gravity is 9.81 m/sec^2.

Answers

Answer:

a) Fnet = mg - Fb - Fr

b) 8.67 secs

Explanation:

mass of object = 80 kg

Buoyancy force = 1/50 * weight ( 80 * 9.81 ) = 15.696

Proportionality constant = 10 N-sec/m

a) Calculate  equation of motion of the object

Force of resistance on object  due to water = Fr ∝ V

                                                                         = Fr = Kv = 10 V

Given that : Fb( due to buoyancy ) , Fr ( Force of resistance ) acts in the positive y-direction on the object  while mg ( weight ) acts in the negative y - direction on the object.

Fnet = mg - Fb - Fr

∴ Equation of motion of the object ( Ma = mg - Fb - Fr )

b) Calculate how long before velocity of the object hits 40 m/s

Ma = mg - Fb - Fr

a = 9.81 - 0.1962 - 0.125 V = 9.6138 - 0.125 V

V = u + at ---- ( 1 )

u = 0

V = 40 m/s

a = 9.6138 - 0.125 V

back to equation 1

40 = 0 + ( 9.6138 - 0.125 (40) ) t

40 = 4.6138 t

∴ t = 40 / 4.6138 = 8.67 secs

trong cùng một nhiệt độ, lượng năng lượng trên mỗi mol của chất khí nào lớn nhất
a) Khí đơn nguyên tử
b) Khí có từ ba nguyên tử
c) Khí lưỡng nguyên tử

Answers

Ben works as a medical assistant. He needs to take a patient's vitals, but the patient is refusing to cooperate. He hasn't experienced this before, so he decides to ask a nurse for advice on how to handle it. This is making a decision by O a) delegation. O b) command. c) vote. O d) consult. Question
Other Questions
Help pls will give brainliest ITS IN THE PICTURE !!!!!! Help pls ?? I really dont know what to do 1. Ten times the sum of -270 and a number gives -20. not sure how to solve what is heavier ten tons of wool or ten tons of steel Question 1 Chapter 4[female] Dis, Raphal, quels sont tes projets pour le week-end prochain?[male] Vendredi aprs-midi, je pars avec mon pre, ma mre et mon frre la Nouvelle-Orlans.[female] Quest-ce que vous allez faire l-bas?[male] Nous allons voir ma sur. Elle habite avec son mari et son fils dans le Vieux Carr.[female] Tu as un neveu?[male] Oui. Il est encore tout petit. Il a trois mois et mes parents vont le voir trs souvent.[female] Tu as lintention de sortir?[male] Oui, bien sr! Vendredi soir, nous allons couter du jazz dans un petit caf sympa du quartier.[female] Et samedi?[male] On va se promener au bord du Mississipi. Il y a un trs beau parc le long du fleuve. Et aprs, on va aller prendre un caf et manger de dlicieux beignets avant de repartir pour Houston.[female] Quel week-end sympa! La vie est belle!1. Where is Raphal going for the weekend?Enter Text2. Who is he traveling with?Enter Text3. Why are they making the trip?Enter Text4. What are their plans for Friday night?Enter Text5. What is one of the things they will do on Saturday?Enter Text A specialized diet would be needed toA. help someone decide what kind of healthy foods they want to eatB. help someone make changes due to a medical issue or ethical concernC. help someone recognize when they are physically hungry instead of emotionally hungryD. help someone with fast results in losing weight without putting in much effort To find hot sauce in a large grocery store, you could systematically search every shelf in every store aisle. This best illustrates problem solving by means of the availability heuristic. functional fixedness. the representativeness heuristic. an algorithm. mental set. Simplify xy-5x+y^2xy5x+y 2 if x = -3 and y = 5. Which Venn Diagram is NOT correct? Determining the Domain and Range from a GraphDetermine the domain and range of the given function.The domain isty4The range is2-4-24Into The purpose of Mendel's experiments with dihybrid crosses was to determinewhether:A. an F2 generation could be produced from the Fi offspring.B. one of two traits could be transformed by DNA.O c. one trait would affect how another is inherited.D. traits are controlled by more than one gene. Which of the following sentences uses the present perfect correctly?Mi padre cubre la olla.Mi padre ha cubrido la olla.Mi padre ha cubierto la olla.Mi padre has cubrido la olla. A rental car company charges $29 per day to rent a car and $0.09 for every mile driven. Claire wants to rent a car, knowing that:She plans to drive 400 miles.She has at most $210 to spend.Use the drop-down menu below to write an inequality representing dd, the total number of days Claire can rent the car while staying within her budget. Help! ASAP. The question is in the attachment below Question 322.5 ptsThere are how many different types of respiration?onetwothreefour Group elements number 11 to 20 as either metallic, non metallic or metalloid. Why I Like Chocolate(1) There are many reasons why I like chocolate. (2) The first reason is that it tastes amazing. (3) Many people all over the world love chocolate and say that it is delicious. (4) Another reason why I like chocolate is that I can make other treats with it. (5) Chocolate pie, truffles, chocolate covered strawberries, and toffee are just a few of the treats that can be made with chocolate. (6) Finally, I like chocolate because it is good for your body. (7) I read many articles that say that dark chocolate is good for your heart. (8) The above reasons are just a few of the many reasons why I like chocolate.Identify the second main point.can someone please tell me if it's 1 2 3 4 5 6 7 or 8 Name three characteristics of a short story.