It would take approximately 161 minutes to raise the temperature of the air in the living room by 10.0°C using the given heater.
Using the formula P = IV, where P is power, I is current, and V is voltage, we can find the current flowing through the heating coil,
I = P/V = 1500 W/120 V = 12.5 A
To find the resistance of the heater, we can use Ohm's law, which states that V = IR, where V is voltage and R is resistance,
R = V/I = 120 V/12.5 A = 9.6 ohms
To calculate the amount of heat required to raise the temperature of the air in the living room, we can use the formula Q = mcΔT, where Q is heat, m is mass, c is specific heat, and ΔT is the change in temperature.
First, we need to find the mass of the air in the living room. The volume of the living room is 3.00 m × 5.00 m × 8.00 m = 120.00 m^3. Since the density of air is 1.20 kg/m^3, the mass of the air in the living room is,
m = density × volume = 1.20 kg/m^3 × 120.00 m^3 = 144 kg
Next, we can calculate the amount of heat required,
Q = mcΔT = (144 kg)(1006 J/(kg·°C))(10.0°C) = 1.45 × 10^7 J
Finally, we can use the formula Q = Pt, where t is time, to find the time required to generate this amount of heat,
t = Q/P = (1.45 × 10^7 J)/(1500 W) = 9667 seconds ≈ 161 minutes.
To know more about resistance, here
brainly.com/question/30720709
#SPJ4
basic behavior: according to your data, does this resistance increase or decrease with voltage? a reasonable (and correct) thought is that the impact is really with temperature, as the light bulb heats up with more power going into it. how does your data imply resistance varies with temperature?
Based on the given question, the resistance will: increase with the increase in voltage.
The reason behind this is that resistance and voltage have a direct relationship. As the voltage increases, the resistance also increases. This can be explained by Ohm’s Law which states that V= IR where V is voltage, I is current and R is resistance. As per the second part of the question, it is implied that the resistance varies with temperature.
The resistance of any material depends upon temperature, and a rise in temperature increases the resistance of the material. The light bulb acts as a resistor, and its resistance will increase as the temperature increases due to an increase in the temperature of the filament of the bulb.
The resistance is directly proportional to the temperature of the bulb, and it is represented by the equation
R = R₀ (1 + αt),
where R is resistance, R₀ is the resistance at a particular temperature, α is the temperature coefficient of resistance, and t is the temperature difference in Celsius.
Therefore, based on the data provided, it can be concluded that resistance increases with the increase in temperature which results in the heating of the light bulb, which is a resistor.
To know more about resistance refer here:
https://brainly.com/question/29427458#
#SPJ11
What are water droplets that act as a prism?
O a
Ob
OC
Od
mirage
rainbow
filter
concave mirror
Water droplets that act as prism are phenomenon known as : b) rainbow.
What are water droplets that act as prism?When light enters water droplet and is refracted, it is dispersed into its component colors due to difference in the index of refraction of each color of light. This results in band of colors in the shape of arc with red on outer edge and violet on inner edge, with other colors of spectrum in between. This is the same effect as prism which disperses light in the same way.
Rainbows appear in seven colors because water droplets break sunlight into seven colors of spectrum and you get the same result when sunlight passes through prism. Water droplets in the atmosphere act as prism though traces of light are very complex.
To know more about rainbow, refer
https://brainly.com/question/1550509
#SPJ1
Which of the following statements is true about the relationship between the two forms of Newton's second law (Fnet = dp/dt and Fnet = m.a) Select the correct answer
a. Fnet = dp/dt reduces to Fnet = m.a if the O acceleration of the object does not change with time. b. Fnet = m.a reduces to Fnet = dp/dt if the acceleration of the object does not change with time. c. Fnet = m.a reduces to Fnet = dp/dt if the mass of the object Answer dt does not change with time. d. Fnet = m.a reduces to Fnet = m.a if the dt momentum of the object does not change with time. e. Fnet = dp/dt reduces to Fnet = m.a if the mass of the object does not change with time. f. Fnet = m.a reduces to Fnet = dp/dt if the momentum of the object does not change with time.
The correct statement about the relationship between the two forms of Newton's second law (Fnet = dp/dt and Fnet = m.a) is option D "Fnet = m.a reduces to Fnet = dp/dt if the momentum of the object does not change with time.
What is Newton's second law?Newton's second law of motion states that the acceleration of an object is directly proportional to the force applied to it and inversely proportional to its mass. In other words, Fnet = m.a, where Fnet is the net force acting on an object, m is its mass, and a is its acceleration. This law can also be written as Fnet = dp/dt, where dp/dt is the rate of change of momentum with time.
Since momentum is the product of mass and velocity, it can be rewritten as dp/dt = m.dv/dt + v.dm/dt, where v is the velocity of the object. If the mass of the object remains constant over time, then v.dm/dt is zero and dp/dt reduces to m.dv/dt, which is equal to Fnet.
Therefore, Fnet = dp/dt reduces to Fnet = m.a if the object's acceleration does not change with time. If the momentum of the object does not change with time, then dp/dt is zero, and Fnet = dp/dt reduces to zero, which means that Fnet = m.a is also zero. Therefore, Fnet = m.a reduces to Fnet = dp/dt if the momentum of the object does not change with time.
To know more about Newton's second law:
https://brainly.com/question/13447525
#SPJ11
When you hear the sound from a vehicle that is moving toward you, the pitch is higher than it would be if the vehicle were stationary. The pitch sounds higher because the
a. sound waves arrive more frequently
b. sound from the approaching vehicle travels faster
c. wavelength of the sound waves becomes greater
d. amplitude of the sound waves increases
Option (A) "sound waves arrive more frequently" is the correct answer. This is because when the sound from a vehicle that is moving toward you is heard, the pitch is higher than it would be if the vehicle were stationary.
What is pitch?Pitch is defined as the highness or lowness of a sound. In other words, pitch is a perception of the frequency of a sound. The pitch of a sound is determined by the number of sound wave cycles per second, which is measured in hertz (Hz).
What are sound waves?Sound waves are a type of energy that is propagated through the air or other mediums. Sound waves are created when an object vibrates and transmits sound energy through the air molecules around it. These vibrations create alternating regions of high and low air pressure that propagate as a sound wave.
A wavelength is defined as the distance between two successive peaks of a sound wave, and it is proportional to the frequency of the sound. When a sound wave's frequency increases, its wavelength becomes shorter, and vice versa. Therefore the correct option is A, sound waves do arrive more frequently.
To know more about the sound wave, click the link: brainly.com/question/1417453
#SPJ11
A 1. 1 kg box drops two meters from a shelf and comes to rest after 0. 021 s on the floor. What force did the box hit the floor
A 1 kg box falls two metres from a shelf and lands on the ground after 0.021 seconds. The box impacted the ground with a force of around 524.7 N.
The box impacted the ground with a force of around 524.7 N.
Explanation: We can determine the force using the equation F = m * (v/t), where m is the box's mass, v is the velocity change (which is the ultimate velocity because the box starts at rest and comes to a halt), and t is the time it takes for the box to stop.
Given that the box falls 2 metres and its terminal velocity is 0 m/s, v = 2 m/s.
524.7 N is equal to F = 1.1 kg * (2 m/s / 0.021 s).
learn more about force here:
https://brainly.com/question/13191643
#SPJ4
Burl and Paul have a total weight of 1300 N. The tensions in the ropes that support the scaffold they stand on add to 1800 N. The weight of the scaffold itself must beA. 400 NB. 500 NC. 600 ND. 800 N
Burl and Paul have a total weight of 1300 N. The tensions in the ropes that support the scaffold they stand on add to 1800 N. The weight of the scaffold itself must be 500 N.
What is a scaffold?A scaffold is a temporary structure that is erected to support workers and their equipment when they are performing a job at a height above the ground. In the construction sector, it is widely used, and it is made up of one or more platforms that are supported by a system of frames and poles.
In order to solve the given problem, we'll have to use some mathematical concepts such as addition and subtraction. The total weight of Burl and Paul = 1300 N
The tensions in the ropes that support the scaffold they stand on = 1800 N
Let us suppose that the weight of the scaffold is x.
So, from the given data, we can write down the following equation:
Total weight of Burl, Paul, and the scaffold = Tensions in the ropes + weight of the scaffold
1300 + x = 1800x = 1800 - 1300= 500 N
Therefore, the weight of the scaffold is 500 N.
To learn more about scaffold follow
https://brainly.com/question/14962055
#SPJ11
Let the mass of the sled be m and the magnitude of the net force acting on the sled be Fnet . The sled starts from rest. Consider an interval of time during which the sled covers a distance s and the speed of the sled increases from v1 to v2 . We will use this information to find the relationship between the work done by the net force (otherwise known as the net work) and the change in the kinetic energy of the sled. Use W = F s cos (theta) to find the net work Wnet done on the sled. Express your answer in terms of some or all of the variables m ,v1 and v2 .
Total work done is Wnet = 1/2mv₂² - 1/2mv₁²
Let the mass of the sled be m and the magnitude of the net force acting on the sled be Fnet .
The sled starts from rest. Consider an interval of time during which the sled covers a distance s and the speed of the sled increases from v₁ to v₂ . We will use this information to find the relationship between the work done by the net force (otherwise known as the net work) and the change in the kinetic energy of the sled.
Use W = F s cos (theta) to find the net work Wnet done on the sled. Express your answer in terms of some or all of the variables m ,v₁ and v₂.Using the work-energy principle, we can calculate the work done on an object in terms of its change in kinetic energy. Consider the sled being acted upon by a force Fnet.
W = ΔK is used to calculate the work done on the sled as it moves from rest to velocity v₁ and then to velocity v₂ over a distance s.
Considering the sled to be the system under study, we can write the net work done on the sled as Wnet = ΔK.Wnet = 1/2mv₂² - 1/2mv₁² = Fnet s cos θWnet = Fnet s cos θ = 1/2mv₂² - 1/2mv₁²
To know more about net force click on below link:
https://brainly.com/question/29261584#
#SPJ11
fundamental questions early astronomers tried to answer were: 1) what is the shape and size of earth? 2) what are the distances from earth to the sun and moon? and 3) blank ?
The third fundamental question early astronomers tried to answer was: What are the motions of the planets and stars in the night sky?
The shape of the Earth is an oblate spheroid, and its approximate diameter is 12,742 km. The average distance from Earth to the Sun is 149,598,262 km, and the average distance from Earth to the Moon is 384,400 km. 3) What are the motions of the planets? The motions of the planets were observed by ASTRONOMES to be elliptical, with the Sun at one focus.
Early astronomers were curious to understand the shape and size of Earth, as well as the distances from Earth to the Sun and Moon. Additionally, they were interested in determining the motions of the planets and stars in the night sky.
The ancient Greeks believed that the universe was a series of concentric spheres with the Earth in the center. Aristotle, a Greek philosopher, believed that the Earth was at the center of the universe, and that everything else, including the stars and planets, orbited around it. The Greek philosopher Eratosthenes was the first to calculate the Earth's circumference. He did so by measuring the angle of the sun's rays at noon on the summer solstice at two different locations and using the difference to estimate the distance between the two places.
In conclusion, early astronomers attempted to answer fundamental questions regarding the shape and size of Earth, the distances from Earth to the sun and moon, and the motion of stars and planets in the sky .
To know more about Motion please visit :
https://brainly.com/question/28205978
#SPJ11
standard number of bones in the appendicular skeleton
The standard number of bones in the appendicular skeleton varies slightly among individuals, but it is generally accepted that there are 126 bones in the appendicular skeleton of an adult human.
The appendicular skeleton includes all the bones that are attached to the axial skeleton, which includes the skull, vertebrae, and ribcage. The appendicular skeleton consists of the bones of the arms, legs, pelvis, and shoulder girdle. Here is a breakdown of the number of bones in each part of the appendicular skeleton: Arms: 60 bones (30 in each arm) Legs: 60 bones (30 in each leg) Pelvis: 2 bones Shoulder girdle: 4 bones Adding up these numbers gives a total of 126 bones in the appendicular skeleton. However, this number can vary slightly among individuals due to differences in bone structure and development.
Learn more about bones here:
https://brainly.com/question/29606469
#SPJ4
In the absence of external forces, momentum is conserved ina. quadrupledb. Yes, force will be less on a carpetc. The component of the weight of the block of ice that is parallel to the slope.d. in both elastic and inelastic collisions
In both elastic and inelastic collisions, momentum is conserved in the absence of external forces. Option d is the correct answer.
In the absence of external forces (such as friction, air resistance, or other external influences), the total momentum of a system remains constant. This is known as the law of conservation of momentum. It applies to all types of collisions, including elastic and inelastic collisions.
In an elastic collision, the total kinetic energy of the system is conserved, in addition to the momentum. In an inelastic collision, some of the kinetic energy is transformed into other forms of energy (such as heat or deformation), but the total momentum is still conserved. The conservation of momentum is a fundamental principle in physics and has many applications, from understanding the behavior of subatomic particles to predicting the trajectories of spacecraft. Hence option d is correct.
To know more about momentum, here
brainly.com/question/12941951
#SPJ4
g as a prank, someone drops a water-filled balloon out of a window. the balloon is released from rest at a height of 10.0 m above the ears of a man who is the target. then, because of a guilty conscience, the prankster shouts a warning after the balloon is released. the warning will do no good, however, if shouted after the balloon reaches a certain point, even if the man could react infinitely quickly. assuming that the air temperature is 20 c and ignoring the effect of air resistance on the balloon, determine how far above the man's ears this point is.
The point at which the warning will do no good is 7.50 m above the man's ears.
When a water-filled balloon is released from rest at a height of 10.0 m above the ears of a man, the warning will do no good if shouted after the balloon reaches a certain point. Assuming that the air temperature is 20°C and ignoring the effect of air resistance, this point is 7.50 m above the man's ears.
The vertical displacement (d) can be determined using the equation [tex]d = \frac{vf2}{2g}[/tex], where vf is the final velocity and g is the acceleration due to gravity (9.81 m/s2).
Since the balloon was released from rest, the initial velocity is 0 m/s. Therefore, [tex]d = \frac{02 }{ 2} (\frac{9.81 m}{s2} ) = 0[/tex]m. Since the initial height was 10.0 m, the final height is 10.0 m + 0 m = 10.0 m.
The point at which the warning will do no good is 7.50 m above the man's ears, so the final height of the balloon must be 10.0 m - 7.50 m = 2.50 m.
Therefore, the point at which the warning will do no good is 7.50 m above the man's ears.
Learn more about vertical displacement: brainly.com/question/2289543
#SPJ11
Proton 1 moves with a speed v from the east coast to the west coast in the continental United States; proton 2 moves with the same speed from the southern United States toward Canada. Is the magnitude of the magnetic force experienced by proton 2 greater than, less than, or equal to the force experienced by proton 1? O greater than the force experienced by proton 1 O less than the force experienced by proton 1 equal to the force experienced by proton 1
The magnitude of the magnetic force experienced by proton 2 will be less than the force experienced by proton 1. This is because the force experienced by a proton is related to the direction of its motion relative to the direction of the magnetic field.
As proton 1 is travelling from east to west, its motion is parallel to the magnetic field, which is aligned in a north-south direction in the continental United States. This means that proton 1 will experience a greater force due to the magnetic field than proton 2, which is travelling in a north-south direction and thus has a motion perpendicular to the magnetic field.
To understand this more clearly, we can consider the equation for the magnetic force:
F = qvB sin θ.
In this equation, the force experienced by a particle is related to the charge (q), velocity (v), and magnetic field strength (B). The sine of the angle between the velocity and magnetic field (θ) is also important as it determines how much of the force will be experienced by the particle. As proton 1's motion is parallel to the magnetic field, it will experience the full force due to the magnetic field, whereas proton 2's motion is perpendicular to the magnetic field and it will only experience a fraction of the force. The magnitude of the force experienced by proton 2 will be lower than the force experienced by proton 1.
For similar question magnitude of the magnetic force
https://brainly.com/question/29237710
#SPJ11
a ball is dropped a from a height of 16ft each time it hits the ground what is the total vertical distance it traveled after it came to rest
The total vertical distance that the ball traveled after it came to rest is 32 feet. This is because each time it hits the ground, it has to travel the initial 16 feet.
Given, a ball is dropped from a height of 16ft. When it hits the ground each time, it bounces back to a height of 8ft. Now, we need to find the total vertical distance that the ball travels after it comes to rest. After the first drop, the ball travels a total distance of 16ft + 8ft = 24ft. After the second drop, the ball travels a total distance of 8ft + 8ft = 16ft.
After the third drop, the ball travels a total distance of 8ft + 8ft = 16ft. After the fourth drop, the ball travels a total distance of 8ft + 8ft = 16ft.S ince the ball has come to rest after the fourth drop, the total distance it has traveled vertically is 24ft + 16ft + 16ft + 16ft = 72ft. The ball travels a total vertical distance of 72ft in four drops.
However, since it comes to rest after the fourth drop, we only consider the distance traveled in three drops, which is 24ft + 16ft + 16ft = 56ft. Therefore, the ball would travel a total vertical distance of 32 feet after coming to rest.
Learn more about distance and rates: https://brainly.com/question/24659604
#SPJ11
a skater of mass 70.0 kg initially moves in a straight line at a speed of 4.80 m/s. the skater approaches a child of mass 39.5 kg, whom he lifts on his shoulders. assuming there are no external horizontal forces, what is the skater's final velocity?
The final velocity of the skater (with the child on their shoulders) is 3.08 m/s.
A skater of mass 70.0 kg initially moves in a straight line at a speed of 4.80 m/s.
When the skater lifts a child of mass 39.5 kg onto their shoulders, their final velocity (assuming there are no external horizontal forces) can be calculated using the law of conservation of momentum.
Momentum is defined as the product of mass and velocity. Therefore, the final momentum of the skater and child can be expressed as:
Final Momentum = (70.0 kg x 4.80 m/s) + (39.5 kg x 0 m/s) = 336 kg m/s
To find the final velocity, we must first find the total mass of the skater and child:
Total Mass = 70.0 kg + 39.5 kg = 109.5 kg
Using the law of conservation of momentum and the total mass, the final velocity of the skater can be expressed as:
Final Velocity = Final Momentum / Total Mass = 336 kg m/s / 109.5 kg = 3.08 m/s
To know more about "final velocity" refer here:
https://brainly.com/question/9163788#
#SPJ11
determine the greatest load p that can be applied to the truss in (figure 1) so that none of the members are subjected to a force exceeding either 2.2 kn in tension or 1.9 kn in compression.
Hence, we can write:1.9 kN > RCD⇒ 1.9 kN > 4.1 kN - P⇒ P < 4.1 kN - 1.9 kN⇒ P < 2.2 kN
Therefore, the maximum load P that can be applied to the truss is P < 2.2 kN.So, the greatest load that can be applied to the truss in Figure 1 is 2.2 kN.
Given Data:Maximum tension load that each bar can bear = 2.2 kN Maximum compressive load that each bar can bear = 1.9 kNTo find:The greatest load P that can be applied to the truss in Figure 1
Approach:First of all, we need to find the bar which is subjected to maximum tension or compression force.Then, we can calculate the maximum load that the bar can bear.Using the method of joints, we can find the load in each bar of the truss.Finally, we can compare the load in each bar with the maximum load that it can bear, to find the maximum load P that can be applied to the truss.
Calculation:First, we will find the bar which is subjected to maximum tension or compression force.We can see that the bars AD and CD will have maximum tensile and compressive forces respectively in bar AD and CD.Using the method of joints,
we can calculate the force in each bar:∑Fy = 0⇒ RCD + RDA = P⇒ RDA = P - RCD∑FCD = 0⇒ RCD - 2.2 - 1.9 = 0⇒ RCD = 4.1 kNSo, we have found the force in bar DA as:RDA = P - RCDWe know that bar AD can bear a maximum load of 2.2 kN in tension. Hence, we can write:2.2 kN > RDA⇒ 2.2 kN > P - RCD⇒ P < RCD + 2.2 kN⇒ P < 4.1 + 2.2 kN = 6.3 kNWe also know that bar CD can bear a maximum load of 1.9 kN in compression.
for such more questions on compressive forces
https://brainly.com/question/13875956
#SPJ11
A set of beliefs can be said to be pseudoscientific if it lacks one or more of the three features of science and _____.
A set of beliefs can be said to be pseudoscientific if it lacks one or more of the three features of science and empirical evidence.
Pseudoscience is a set of claims, beliefs, or practices that are presented as scientific but lack empirical evidence, are inconsistent with scientific facts, or are based on incorrect assumptions. Pseudoscience can be seen in a variety of fields, including medicine, psychology, and the paranormal.
Science is defined by three characteristics: empiricism, theory construction, and parsimony or simplicity. Empiricism is the use of evidence to establish scientific facts, while theory construction is the development of a conceptual framework that explains and predicts these facts.
Parsimony is the principle that the simplest explanation is the best one, meaning that theories should not include unnecessary assumptions or complexity. However, pseudoscientific practices often lack one or more of these characteristics. They may fail to use empirical evidence or instead rely on anecdotal evidence or personal experience. Their theories may not be testable or may be inconsistent with established scientific facts. They may also be unnecessarily complex or based on assumptions that have no basis in reality.
Hence, a set of beliefs can be said to be pseudoscientific if it lacks one or more of the three features of science and empirical evidence.
To know about Pseudoscience, refer here:
https://brainly.com/question/12257058#
#SPJ11
for a given mass of gas at constant temperature, the volume of the gas varies inversely with pressure.a. 3Pb. P/3c. 3P/Td. 9P
The volume of the gas varies inversely with pressure, and the correct answer is (b) P/3.
According to Boyle's Law, at a constant temperature, the volume of a gas is inversely proportional to its pressure. Mathematically, this can be expressed as:
PV = k
where P is the pressure of the gas, V is its volume, and k is a constant.
If we assume that the mass of the gas remains constant, then k is also constant. So we can write:
[tex]P_1V_1 = k and P_2V_2 = k[/tex]
where[tex]P_1 and V_1[/tex] are the initial pressure and volume, and [tex]P_2 and V_2[/tex] are the final pressure and volume.
If we divide these two equations, we get:
[tex]P_1V_1/P_2V_2 = 1[/tex]
Since[tex]V_1[/tex] is inversely proportional to [tex]P_1[/tex], we can write:
[tex]V_1 = k/P_1[/tex]
Similarly, [tex]V_2 = k/P_2.[/tex]
Substituting these values in the above equation, we get:
[tex](k/P_1)/(k/P_2) = 1[/tex]
Simplifying this, we get:
[tex]P_2/P_1 = V_1/V_2[/tex]
Since we are given that the temperature remains constant, we can assume that k is constant, and therefore:
[tex]V_1/P_1 = V_2/P_2[/tex]
If we let [tex]P_2 = 3P_1[/tex], then we get:
[tex]V_1/P_1 = V_2/(3P_1)[/tex]
Simplifying this, we get:
[tex]V_1/V_2 = 1/3[/tex]
for such more question on volume
https://brainly.com/question/14197390
#SPJ11
a runner sprints around a circular track of radius 100 m at a constant speed of 7 m/s. the runner's friend is standing at a distance 200 m from the center of the track. how fast is the distance between the friends changing when the distance between them is 200 m? (round your answer to two decimal places.) m/s
The change in the distance between the friends changing when the distance between them is 200 m is 7.85m.
What is the distance?Consider a right-angled triangle with the radius of the circular track as one side of the right angle. Then the other two sides are the distance covered by the runner (in a single lap) and the distance between the runner and his friend.
Since the radius is perpendicular to the line connecting the friend and the center of the track, we can call it the hypotenuse of the triangle.
Let x be the distance between the runner and his friend. We are given that x = 200 m.Using the Pythagorean theorem, we can find the distance covered by the runner in a single lap of the track.
e can now differentiate the above expression with respect to time to find the rate of change of the distance covered by the runner (this will also be the rate of change of the distance between the runner and his friend).Hence,
2x(dx/dt) = 2 (distance covered by runner)(d(distance covered by runner)/dt)
dx/dt = (distance covered by runner)
(d(distance covered by runner)/dt) / x
Substituting x = 200 m and d(distance covered by runner)/dt = 7 m/s, we get:
dx/dt = (223.6 m)(7 m/s) / 200 m = 7.85 m/s.
Rounding off to two decimal places, we get:
dx/dt = 7.85 m/s.
Therefore, the answer is 7.85.
Read more about distance here:
https://brainly.com/question/26046491
#SPJ11
The volume of a sphere is increasing at the rate of 8cm3/s. Find the rate at which its surface area is increasing when the radius of the sphere is 12cm.
The rate at which the surface area of the sphere is increasing when the radius of the sphere is 12 cm is 1/226.5 cm/s.
What is the rate of surface area change?The volume of a sphere is increasing at the rate of 8 cm³/s.
Radius of the sphere is 12 cm.
So, we need to find the rate at which its surface area is increasing.
Let, V be the volume of the sphere and r be the radius of the sphere. The volume of a sphere of radius r is given by:
V = (4/3)πr³
Differentiating with respect to time t, we get:
dV/dt = 4πr²(dr/dt) ...(1)
Also, the surface area of the sphere is given by:
A = 4πr²
Differentiating with respect to time t, we get:
dA/dt = 8πr(dr/dt) ...(2)
From equations (1) and (2), we can write:
dr/dt = dV/dt ÷ 4πr²
dr/dt = 8 / (4π × 12²)
dr/dt = 8 / 1808
dr/dt = 1 / 226.5 cm/s
Therefore, the rate at which the surface area of the sphere is increasing when the radius of the sphere is 12 cm is 1/226.5 cm/s.
Learn more about Surface area here:
https://brainly.com/question/29101132
#SPJ11
Imagine you are viewing the other planets from Earth. Which planets (if any) will appear to pass directly in front of the Sun from your Earth-based perspective? Which planets (if any) will never transit the Sun? If you were able to view the Solar System from outside, how many planets could potentially transit the Sun? Will those planets transit the Sun no matter where outside the Solar System you are? Sketch and describe the required orientation of the Solar System in order for the maximum number of planets to transit the Sun.
Explanation:
Planets closer to the sun will appear to transit from time to time
= 2 Venus and Mercury ( I suppose you could include the Moon..an eclipse ....haha)
All of the planets further from the sun than earth will not transit
Potentially ALL of the planets could transit the sun (earth included) if observed outside solar system HOWEVER if you are not observing from near the orbital plane of
the planets NONE of them would transit
For maximum transits, the planets should all be in the same orbital plane and the observer should be very close to this plane also.
A 910-kg sports car collides into the rear end of a 2100-kg SUV stopped at a red light. The bumpers lock, the brakes are locked, and the two cars skid forward 2.5m before stopping. The police officer, estimating the coefficient of kinetic friction between tires and road to be 0.80, calculates the speed of the sports car at impact.
1.A 910-kg sports car collides into the rear end of a 2100-kgSUV stopped at a red light. The bumpers lock, the brakes are locked, and the two cars skid forward 2.5m before stopping. The police officer, estimating the coefficient of kinetic friction between tires and road to be 0.80, calculates the speed of the sports car at impact.
1.What was the speed sports car at impact?
The speed of the sports car at impact when kinetic friction between tires and road is 0.80 is 15.55 m/s.
It is given that Mass of sports car, ms = 910 kg, Mass of SUV, mSUV = 2100 kg, and Initial velocity of sports car, us = ?, Final velocity of sports car, v = 0, Initial velocity of SUV, uSUV = 0, Final velocity of SUV, vSUV = 0, and Coefficient of kinetic friction, μk = 0.80. Distance covered before stopping, s = 2.5 m.
We know that the total momentum of the system remains conserved, we can write:
ms * us + mSUV * uSUV = (ms + mSUV) * v
Thus,
ms * us = (ms + mSUV) * v
The speed of the sports car at impact when kinetic friction between tires and road is 0.80 is 15.55 m/s.
It is given that Mass of sports car, ms = 910 kg, Mass of SUV, mSUV = 2100 kg, and Initial velocity of sports car, us = ?, Final velocity of sports car, v = 0, Initial velocity of SUV, uSUV = 0, Final velocity of SUV, vSUV = 0, and Coefficient of kinetic friction, μk = 0.80. Distance covered before stopping, s = 2.5 m.
We know that the total momentum of the system remains conserved, we can write:
ms * us + mSUV * uSUV = (ms + mSUV) * v
Thus,
ms * us = (ms + mSUV) * v
Since the two cars skid together, the frictional force provides the reduction to the motion of the cars. The reduction force F = μk * N where N is the normal force acting on the cars, N = (ms + mSUV) * g where g is the acceleration due to gravity, g = 9.8 m/s².
We have to find the speed of the sports car at impact i.e. us. So, using the equations of motion with constant acceleration, we can write:
us² - 2 * μk * (ms + mSUV) * g * s / (ms + mSUV) = v²
us² = 2 * μk * (ms + mSUV) * g * s / ms
us = sqrt [2 * 0.80 * (910 + 2100) * 9.8 * 2.5 / 910]
us = 15.55 m/s
Therefore, the speed of the sports car at impact is 15.55 m/s.
Learn more about Kinetic friction:
https://brainly.com/question/20241845
#SPJ11
two forces are applied to a 12 kg cart on a frictionless surface as shown. at a certain instant, force a is 77 n to the right, and force b is 15 n to the left. what is the acceleration of the cart at this instant, in m/s2?
The acceleration of the cart at this instant is calculated to be 5.17 m/s² to the right.
What is Newton's second law?Newton's second law explains that acceleration of any object is directly related to net force and inversely related to the mass.
To determine the acceleration of the cart, we need to calculate the net force acting on it.
The net force is the vector sum of the two forces:
Net force = Force a + Force b = 77 N to the right - 15 N to the left = 62 N to the right
Using Newton's second law, F = ma, where F is the net force and m is the mass of the cart, we can calculate the acceleration:
a = F/m = 62 N / 12 kg = 5.17 m/s
Therefore, the acceleration of the cart at this instant is 5.17 m/s² to the right.
To know more about Newtons' law, refer
https://brainly.com/question/28171613
#SPJ1
if the leftover energy in the previous problem is 134.9 j (it's not, don't go back and try to use this value) and the mass is 2 kg, what speed (in m/s) does the block have at the bottom of its slide? revisit the definition of ke if needed.
The speed of the block at the bottom of its slide is 16.4 m/s.
In the previous problem, the kinetic energy of the block was found to be 135 J.
The formula for kinetic energy is
KE = 1/2mv²,
Where:
m is the mass of the object and v is its velocity.Now we can use the same formula to find the velocity of the block at the bottom of its slide.
KE = 1/2mv²
We know that the mass of the block is 2 kg, and the kinetic energy at the end of the slide is 135 J.
KE = 135 Jm = 2 kg1/2mv² = 135 Jv² = 2(135 J) / 2 kgv² = 270 JV = sqrt(270 J) / 2 kgV = 16.4 m/s
Therefore, the speed of the block at the bottom of its slide is 16.4 m/s.
Learn more about kinetic energy: https://brainly.com/question/8101588
#SPJ11
A train P covered a distance of 180 km in 4.5 hours and train Q covered 270 km in 6 hours. Which train is moving faster?
ans= train Q
Sol= 4.5×60= 270
6×60= 360
270÷180=1.5
360÷270=1.3...
1.3... <1.5
What is the goal of correlation?
A. to predict the trend of the types of rocks that will be deposited in the future
B. to gain a more comprehensive view of the geologic history of a region
C. to determine the completeness of the fossil record within a particular rock layer
D. to predict the sequence of rock types as one moves up a single rock column
E. to develop individual geologic time scales that pertain only to discreet geographic locations
The goal of correlation is to gain a more comprehensive view of the geologic history of a region. the correct option is B.
Correlation is the process of relating one set of rock layers to another set of rock layers by examining their stratigraphic relationships. It is important in geology to correlate rocks and fossils across regions to develop a better understanding of the Earth's history. Correlation is an important geological technique because it provides information with regard to changes that have taken place at various times in Earth's history. It also provides information about the times at which such changes have occurred.
To know more about Correlation: https://brainly.com/question/6454167
#SPJ11
Two charges, -2.1 μC and -5.6 μC , are located at (-0.50 m , 0) and (0.50 m , 0), respectively. There is a point on the x-axis between the two charges where the electric field is zero. Find the location of the point where the electric field is zero
The point on the x-axis between the two charges where the electric field is zero is 0.747 m, when the charges -2.1 μC and -5.6 μC are located at (-0.50 m , 0) and (0.50 m , 0), respectively.
An electric field is defined as the electric force per unit charge. It is a field of force surrounding electrically charged particles, such as electrons or protons in motion, that exerts force on surrounding matter. It is represented by the symbol E.
The electric field E at any point (x,y) on the x-axis due to the charge Q1 at (-0.50 m, 0) is
[tex]E1 = k * Q1 / r1^2[/tex]
where, k = Coulomb's constant = [tex]9 x 10^9 Nm^2/C^2[/tex]
Q1 = charge = -2.1 μC
r1 = distance between Q1 and
(x,y) = (0.50 + x) m
The electric field E at any point (x,y) on the x-axis due to the charge Q2 at (0.50 m, 0) is
[tex]E2 = k * Q2 / r2^2[/tex]
where,
Q2 = charge = -5.6 μC
r2 = distance between Q2 and (x,y) = (0.50 - x) m
The total electric field E at any point (x,y) on the x-axis due to both the charges is
[tex]E = E1 + E2 = k * Q1 / r1^2 + k * Q2 / r2^2[/tex]
[tex]E = k * (-2.1 * 10^-6) / (0.5 + x)^2 + k * (-5.6 * 10^-6) / (0.5 - x)^2[/tex]
At the point on the x-axis between the two charges where the electric field is zero,
[tex]E = 0k * (-2.1 * 10^-6) / (0.5 + x)^2 + k * (-5.6 * 10^-6) / (0.5 - x)^2 = 0[/tex]
Simplifying, we get [tex](0.5 + x)^2 / (0.5 - x)^2 = 2.667x^2 + 2.667x - 0.50 = 0[/tex]
Solving for x, we get
x = -1.74 m or
x = 0.747 m
We cannot have a negative value of x as the point has to be between the two charges. So, the location of the point where the electric field is zero is x = 0.747 m.
Learn more about electric field: https://brainly.com/question/14372859
#SPJ11
an airplane flies due west at an airspeed of 425 mph. the wind is blowing from the northeast at 40 mph. what is the ground speed of the airplane? what is the bearing of the airplane?
An airplane flies due west at an airspeed of 425 mph and the wind is blowing from the northeast at 40 mph, the ground speed of the airplane is 385 mph, and the bearing of the airplane is 285°.
We can use the equation
GS = AS + (Wind x cos(Θ)),
Where GS is the ground speed, AS is the airspeed, and Θ is the angle between the wind and the heading of the airplane. the airspeed is 425 mph, the wind is blowing from the northeast at 40 mph, and the heading of the airplane is due west. The angle Θ is 90°. Plugging these values into the equation, we get
GS = 425 + (40 x cos(90°)) = 385 mph.
To calculate the bearing of the airplane, we can use the equation
Bearing = 180° - (Θ + (Wind ÷ AS) x 180°).
Θ is 90°, the wind is 40 mph, and the airspeed is 425 mph.
Plugging these values into the equation, we get
Bearing = 180° - (90° + (40 ÷ 425) x 180°) = 285°.
Hence , airplane flies due west at an airspeed of 425 mph and the wind is blowing from the northeast at 40 mph, the ground speed of the airplane is 385 mph, and the bearing of the airplane is 285°.
To know more about Ground speed please visit :
https://brainly.com/question/24208048
#SPJ11
A student graphed the position of a cart during a 7-second time interval.
The correct option is D; The cart moved at a constant velocity of 0.5m/s for the entire 7 seconds.
Which graph best represents a constant acceleration?Constant acceleration is represented as a horizontal line on the acceleration graph. The slope of the velocity graph represents the acceleration. On the velocity graph, constant acceleration Equals constant slope = straight line.
Acceleration is represented in a velocity-time graph by the slope, or steepness, of the graph line. If the line slopes upward, as seen in the figure between 0 and 4 seconds, velocity increases, and acceleration is positive. The velocity-time graph will be a curve when the acceleration increases with time, as anticipated by the equation: v = u + at.
Learn more about velocity
https://brainly.com/question/24909693
#SPJ1
5x, 10x and 20x objective lenses. what is the maximum total magnification that can be achieved with this microscope?
The maximum total magnification that can be achieved with a microscope that has 5x, 10x, and 20x objective lenses can be found by multiplying the magnification of the objective lens by the magnification of the eyepiece lens.
What is Magnification?This can be expressed as:
Magnification = objective lens magnification × eyepiece lens magnification
The eyepiece lens magnification is typically 10x for most microscopes, so we can simply find the maximum total magnification by multiplying each objective lens magnification by 10 and then adding them together:
Maximum Total Magnification = (5 × 10) + (10 × 10) + (20 × 10)
Maximum Total Magnification = 50 + 100 + 200
Maximum Total Magnification = 350
Therefore, the maximum total magnification that can be achieved with this microscope is 350x.
Learn more about Magnification here:
https://brainly.com/question/3851549
#SPJ11
which unit is used to measure force?(1 point) responses watt watt kilogram kilogram newton newton joule
According to the International System of Units, Newton (N) is used to measure force. Thus Newton is the correct response.
A force is defined as a physical quantity that causes a change in the state of motion of a body.
Force is a vector quantity that has both magnitude and direction.
Newton is the unit of force in the International System of Units (SI).
One newton (N) is the amount of force required to give a mass of 1 kg and an acceleration of 1 m/s².
Learn more about Force here:
brainly.com/question/12785175
#SPJ11
