A ball is thrown from the ground so that it’s initial vertical and horizontal components of velocity are 40m/s and 20m/s respectively. Find the ball’s total time of flight and distance it traverses before hitting the ground.

Answers

Answer 1

Answer:

8 seconds

160 meters

Explanation:

Given in the y direction:

Δy = 0 m

v₀ = 40 m/s

a = -10 m/s²

Find: t

Δy = v₀ t + ½ at²

0 m = (40 m/s) t + ½ (-10 m/s²) t²

0 = 40t − 5t²

0 = 5t (8 − t)

t = 0 or 8

Given in the x direction:

v₀ = 20 m/s

a = 0 m/s²

t = 8 s

Find: Δx

Δx = v₀ t + ½ at²

Δx = (20 m/s) (8 s) + ½ (0 m/s²) (8 s)²

Δx = 160 m


Related Questions

A 180-km-long high-voltage transmission line 2.00 cm in diameter carries a steady current of 1,050 A. If the conductor is copper with a free charge density of 8.50 1028 electrons per cubic meter, how many years does it take one electron to travel the full length of the cable

Answers

Answer:

27yrs

Explanation:

h= difference in height between the initial position and the bottom position

We are told that the rope is L = 2.30 m long and inclined at 45.0° from the vertical

h=L-Lcos(x)= L(1-cosx)=2.30(1-cos45)

=0.674m

Potential Energy = 28× 9.8×0.674

=184.9J

B)we can see that at the bottom of the motion, all the initial potential energy of the child has been converted into kinetic energy:

E= 0.5mv^2

Changing the speed of a synchronous generator changes A) the frequency and amplitude of the output voltage. B) only the frequency of the output voltage. C) only the amplitude of the output voltage. D) only the phase of the output voltage.

Answers

Answer:

A) the frequency and amplitude of the output voltag

Explanation:

Changing the speed of a synchronous generator changes both the output voltage (amplitude of the wave) and frequency as they tend to increase.

Changing the speed regulator will change the engine throttle setting to maintain the speed.

While the power, torque, current, fuel flow rate and torque angle will have decreased.

A Van de Graaff generator produces a beam of 2.02-MeV deuterons, which are heavy hydrogen nuclei containing a proton and a neutron.
A) If the beam current is 10.0 μA, how far apart are the deuterons?
B) Is the electrical force of repulsion among them a significant factor in beam stability? Explain.

Answers

Answer:

A)  The distance of the deuterons from one another  = 2.224× 10⁻⁷ m

B)  The electrical force of repulsion among them shows a small effect  in beam stability.

Explanation:

Given that:

A Van de Graaff generator produces a beam of 2.02-MeV deuterons

If the beam current is 10.0 μA, the distance of the deuterons from one another can be determined by using the concept of kinetic energy of the generator.

[tex]\mathtt{K.E = \dfrac{1}{2}mv^2}[/tex]

2 K.E = mv²

[tex]\mathtt{v^2 = \dfrac{2 K.E }{m}}[/tex]

[tex]\mathtt{v =\sqrt{ \dfrac{2 K.E }{m}}}[/tex]

so, v is the velocity of the deuterons showing the distance of the deuterons apart from one another.

[tex]\mathtt{v =\sqrt{ \dfrac{2 (2.02 \ MeV) \times \dfrac{10^6 \ eV}{ 1 \ MeV} \times \dfrac{1.60 \times 10^{-19} \ J }{1 \ eV} }{ 3.34 \times 10^ {-27} \ kg}}}[/tex]

[tex]\mathtt{v =\sqrt{ \dfrac{6.464 \times 10^{-13} \ J }{ 3.34 \times 10^ {-27} \ kg}}}[/tex]

v = 13911611.49  m/s

v = 1.39 × 10⁷ m/s

So, If the beam current is 10.0 μA.

We all know that:

[tex]I = \dfrac{q}{t}[/tex]

[tex]t = \dfrac{q}{I}[/tex]

[tex]\mathtt{ t = \dfrac{1.6 * 10 ^{-19} \ C}{10.0 * 10^{-6} \ A}}[/tex]

t = 1.6 × 10⁻¹⁴ s

Finally, the distance of the deuterons from one another  = v × t

the distance of the deuterons from one another  = (1.39 × 10⁷ m/s × 1.6 × 10⁻¹⁴ s)

the distance of the deuterons from one another  = 2.224× 10⁻⁷ m

B) Is the electrical force of repulsion among them a significant factor in beam stability? Explain.

The electrical force of repulsion among them shows a small effect  in beam stability. This is because, one nucleus tends to put its nearest neighbor at potential V = (k.E × q) / r = 7.3e⁻⁰³ V. This is very small compared to the 2.02-MeV accelerating potential, Thus, repulsion within the beam is a small effect.

Which one of the following actions would make the maxima in the interference pattern from a grating move closer together?
A. Increasing the number of lines per length.
B. Decreasing the number of lines per length.
C. Increasing the distance to the screen.
D. Increasing the wavelength of the laser.

Answers

Answer:

Answer:

A. Increasing the number of lines per length.

Suppose you exert a force of 185 N tangential to the outer edge of a 1.73-m radius 76-kg grindstone (which is a solid disk).

Required:
a. What torque is exerted?
b. What is the angular acceleration assuming negligible opposing friction?
c. What is the angular acceleration if there is an opposing frictional force of 20.0 N exerted 1.50 cm from the axis?

Answers

Answer:

a. 320.06 Nm b. 2.814 rad/s² c. 2.811 rad/s².

Explanation:

a. The torque exerted τ = Frsinθ where F = tangential force exerted = 185 N, r = radius of grindstone = 1.73 m and θ = 90° since the force is tangential to the grindstone.

τ = Frsinθ

= 185 N × 1.73 m × sin90°

= 320.05 Nm

So, the torque τ = 320.05 Nm

b. Since torque τ = Iα where I = moment of inertia of grindstone = 1/2MR² where M = mass of grindstone = 76 kg and R = radius of grindstone = 1.73 m

α = angular acceleration of grindstone

τ = Iα

α = τ/I = τ/(MR²/2) = 2τ/MR²

substituting the values of the variables, we have

α = 2τ/MR²

= 2 × 320.05 Nm/[76 kg × (1.73 m)²]

= 640.1 Nm/227.4604 kgm²

= 2.814 rad/s²

So, the angular acceleration α = 2.814 rad/s²

c. The opposing frictional force produces a torque τ' = F'r' where F' = frictional force = 20.0 N and r' = distance of frictional force from axis = 1.50 cm = 0.015 m.

So  τ' = F'r' = 20.0 N × 0.015 m = 0.3 Nm

The net torque on the grindstone is thus τ'' = τ - τ' = 320.05 Nm - 0.3 Nm = 319.75 Nm

Since τ'' = Iα

α' = τ''/I where α' = its new angular acceleration

α' = 2τ/MR²

= 2 × 319.75 Nm/[76 kg × (1.73 m)²]

= 639.5 Nm/227.4604 kgm²

= 2.811 rad/s²

So, the angular acceleration α' = 2.811 rad/s²

Consider two parallel wires where the magnitude of the left currentis 2 I0(io) and that of the right current is I0(io). Point A is midway between the wires,and B is an equal distance on the other side of the wires.
The ratio ofthe magnitude of the magnetic field at point A to that at point Bis________

Answers

Answer:

Explanation:

At the point midway between wires

magnetic field due to wire having current 2I₀

= 10⁻⁷ x 2 x2I₀ / r     where 2r is the distance between wires .

magnetic field due to wire having current I₀

= 10⁻⁷ x 4 I₀ / r

magnetic field due to wire having current I₀

= 10⁻⁷ x 2I₀ / r    

= 10⁻⁷ x 2 I₀ / r     where 2r is the distance between wires .

these fields are in opposite direction as direction of current is same in both .

net magnetic field = (4 - 2 )x 10⁻⁷ x I₀ / r

= 2 x 10⁻⁷ x  I₀ / r

At point A net magnetic field = 2 x 10⁻⁷ x  I₀ / r

At point B , we shall calculate magnetic field

magnetic field due to nearer wire having current  2 I₀ = 10⁻⁷ x 4 I₀ / r

magnetic field due to wire far away = 10⁻⁷ x 2 I₀ / 3r

These magnetic fields act in the same direction so they will add up

net magnetic field = [ (4 I₀ / r)  + (2 I₀ / 3r) ] x 10⁻⁷

= (14 I₀ / 3r ) x 10⁻⁷

Magnetic field at point B = (14 I₀ / 3r ) x 10⁻⁷

Ratio of field at A and B

= 3 / 7 . Ans

The ratio of the magnitude of the magnetic field at point A to point B is :

3 / 7

Given data :

Magnitude of the left current is  2I₀

Magnitude of the right current is  I₀

First step : Determine the magnetic field at point A  

The magnetic field due to the left current ( 2I₀ )

10⁻⁷ * 2 * 2I₀ / r       ( 2r = distance between wires )

The magnetic field due to the right current ( I₀ )

10⁻⁷ * 2 I₀ / r

From the expressions above the magnetic fields are in  opposite direction

∴ Net magnetic field = (4 - 2 )* 10⁻⁷ * I₀ / r =   2 * 10⁻⁷ *  I₀ / r

Hence The magnetic field at point A = 2 * 10⁻⁷ *  I₀ / r

Next step : determine the magnetic field at point B

Magnetic field due to the closest wire to point B ( i.e.2I₀ ) = 10⁻⁷ * 4 I₀ / r

Magnetic field due to the wire away from point A = 10⁻⁷ * 2 I₀ / 3r

Since the fields acts in the same directions

The net magnetic field =  (4 I₀ / r)  + (2 I₀ / 3r) ] * 10⁻⁷ = ( 14 I₀ / 3r ) * 10⁻⁷

Hence The magnetic field at point A = ( 14 I₀ / 3r ) * 10⁻⁷

Therefore the ratio of the magnitude of the magnetic field at point A to point B  =  3/ 7

Hence we can conclude that the ratio of the magnitude of the magnetic field at point A to point B  = 3 / 7

Learn more : https://brainly.com/question/22403676

If the x-position of a particle is measured with an uncertainty of 1.00×10-10 m, then what is the uncertainty of the momentum in this same direction? (Useful constant: h-bar = 1.05×10-34 Js.)

Answers

Answer:

The uncertainty in momentum is 5.25x 10^25Jsm

Explanation:

We know that

h bar = h/2π

So

1.05x 10^34=h/2pπ

h=1.05x 10^ 34(2π)=6.597x 10^-34Js

dp=(6.597x10^-34/4pπ)/(1x10^-10)

=5.25x10^-25 Jsm

A light beam has a wavelength of 330 nm in a material of refractive index 1.50. In a material of refractive index 2.50, its wavelength will be In a material of refractive index 2.50, its wavelength will be:_________
a. 495 nm .
b. 330 nm .
c. 220 nm .
d. 198 nm .
e. 132 nm .

Answers

Answer:

The wavelength of the ligt beam in a material of refractive index 2.50 is 198 mm

d. 198 mm

Explanation:

Refractive index is given by;

[tex]\mu= \frac{\lambda_{vacuum}}{\lambda _{medium}}[/tex]

where;

[tex]\lambda_{vacuum}[/tex] is the wavelength of the light beam in vacuum

[tex]\lambda_{medium}[/tex] is the wavelength of the beam in a material

[tex]\mu= \frac{\lambda_{vacuum}}{\lambda _{medium}} \\\\\lambda_{vacuum} = \mu *\lambda _{medium}\\\\\ the \ wavelength \ of \ the \ light \ beam \ is \ constant \ in \ a \ vacuum\\\\ \mu_1 *\lambda _{medium}_1 = \mu_2 *\lambda _{medium}_2\\\\\lambda _{medium}_2 = \frac{ \mu_1 *\lambda _{medium}_1 }{ \mu_2} \\\\\lambda _{medium}_2 =\frac{1.5*330}{2.5} \\\\\lambda _{medium}_2 = 198 \ mm[/tex]

Therefore, the wavelength of the ligt beam in a material of refractive index 2.50 is 198 mm.

d. 198 mm

Experiment to find ways to make rainbows.
a) Insert at least one setup where light passing through a prism gives a rainbow and describe why a rainbow is formed.
b) Explain why only some types of light will yield rainbows.

Answers

Answer:

Explanation:

a) To get a rainbow from a prism arrangement, we will need

A triangular prismA black cardboard boxA source of white light (light from the window will suffice)A pocket knife

First, you cut a slit in one end of the cardboard with the pen knife.

Next you open up a space on top of the cardboard through which you can observe the experiment and its result.

Next, you place the triangular prism with its slant face facing the the cut slit.

Finally, position the slit to face the light from the open window, and adjust the prism till the projected bands of colored light (rainbow) is very much obvious on the other end of the box, opposite the slit.

b) For a light to yield rainbow, it most be composed of different component colors of light. The colors of light is due to the difference in wavelength, and dispersion is due to the different in the wavelengths of the component light. So to get rainbow from a light source, the light must not be monochromatic. This means that only light composed of component light of different colors can produce rainbow. Light from the sun for example is composed of 7 distinct colors of light, and white light can be created with just three colors; blue, green, and red light.

An inductor is connected to the terminals of a battery that has an emf of 12.0 VV and negligible internal resistance. The current is 4.96 mAmA at 0.800 msms after the connection is completed. After a long time the current is 6.60 mAmA. Part A What is the resistance RR of the inductor

Answers

i

CHECK COMPLETE QUESTION BELOW

inductor is connected to the terminals of a battery that has an emf of 12.0 VV and negligible internal resistance. The current is 4.96 mAmA at 0.800 msms after the connection is completed. After a long time the current is 6.60 mAmA.

Part A)What is the resistance RR of the inductor

PART B) what is inductance L of the conductor

Answer:

A)R=1818.18 ohms

B)L=1.0446H

Explanation:

We were given inductor L with resistance R , there is a connection between the battery and the inductor with Emf of 12V, we can see that the circuit is equivalent to a simple RL circuit.

There is current of 4.96mA at 0.8ms, at the end of the connection the current increase to 6.60mA,

.

a)A)What is the resistance RR of the inductor?

The current flowing into RL circuit can be calculated using below expresion

i=ε/R[1-e⁻(R/L)t]

at t=∞ there is maximum current

i(max)= ε/R

Where ε emf of the battery

R is the resistance

R=ε/i(max)

= 12V/(6.60*10⁻³A)

R=1818.18 ohms

Therefore, the resistance R=1818.18 ohms

b)what is inductance L of the conductor?

i(t=0.80ms and 4.96mA

RT/L = ⁻ln[1- 1/t(max)]

Making L subject of formula we have

L=-RT/ln[1-i/i(max)]

If we substitute the values into the above expresion we have

L= -(1818.18 )*(8.0*10⁻⁴)/ln[1-4.96/6.60)]

L=1.0446H

Therefore, the inductor L=1.0446H

An electric heater draws 13 amperes of current when connected to 120 volts. If the price of electricity is $0.10/kWh, what would be the approximate cost of running the heater for 8 hours?
(A) $0.19
(B) $0.29
(C) $0.75
(D) $1.25
(E) $1.55

Answers

Answer:

C $0.75 my friend I wish it is right answer

What is the frequency of the fundamental mode of vibration of a steel piano wire stretched to a tension of 440 N? The wire is 0.630 m long and has a mass of 5.69 g.

Answers

Answer:

220.698Hz

Explanation:

The fundamental frequency f₀ is expressed as f₀ =V/2L where;

V is the speed of the string = [tex]\sqrt{\frac{T}{M} }[/tex]

m is the mass of the string

L is the length of the string

T is the tension in the string

f₀ = [tex]\frac{1}{2L} \sqrt{\frac{T}{m} }[/tex]

Given datas

m = 5.69g = 0.00569 kg

T = 440N

L = 0.630 m

Required

Fundamental frequency of the steel piano wire f₀

[tex]f_0 = \frac{1}{2(0.630)}\sqrt{\frac{440}{0.00569} } \\ \\f_0 = \frac{1}{1.26}\sqrt{77,328.65 } \\\\f_0 = \frac{1}{1.26} * 278.08\\\\f_0 = 220.698Hz[/tex]

Hence the frequency of the fundamental mode of vibration of the steel piano wire stretched to a tension of 440N is 220.698Hz

You perform a double‑slit experiment in order to measure the wavelength of the new laser that you received for your birthday. You set your slit spacing at 1.11 mm and place your screen 8.63 m from the slits. Then, you illuminate the slits with your new toy and find on the screen that the tenth bright fringe is 4.71 cm away from the central bright fringe (counted as the zeroth bright fringe). What is your laser's wavelength lambda expressed in nanometers?

Answers

Answer:

 λ = 605.80 nm

Explanation:

These double-slit experiments the equation for constructive interference is

          d sin θ = m λ

where d is the distance between the slits, λ the wavelength of light and m an integer that determines the order of interference.

In this case, the distance between the slits is d = 1.11 mm = 1.11 10⁻³ m, the distance to the screen is L = 8.63 m, the range number m = 10 and ay = 4.71 cm

Let's use trigonometry to find the angle

         tan θ = y / L

as the angles are very small

          tan θ = sin θ / cos θ = sin θ

we substitute

         sin θ = y / L

we substitute in the first equation

         d y / L = m λ          

          λ = d y / m L

let's calculate

           λ = 1.11 10⁻³ 4.71 10⁻²/ (10 8.63)

           λ = 6.05805 10⁻⁷ m

let's reduce to nm

          λ = 6.05805 10⁻⁷ m (10⁹ nm / 1m)

          λ = 605.80 nm

The power lines are at a high potential relative to the ground, so there is an electric field between the power lines and the ground. To maximize the potential difference between one end of the fluorescent tube and the other, how should the tube be held?a. The tube should be held horizontally, parallel to the ground b. The potential difference between the ends of the tube does not depend on the tube's orientation. c. The tube should be held vertically perpendicular to the ground

Answers

Answer:

b) True. potencial diferencie does not depend on orientation

Explanation:

In this exercise we are asked to show which statements are true.

The expression the potential with respect to earth or the electric field with respect to earth refers to the potential or electric charge of the planet that is assumed to be very large and does not change in value during work.

It does not refer to the height of the system.

We can now review the claims

a) False. Potential not to be refers to height

b) True. Does not depend on orientation

c) False The potential does not refer to the altitude but to the Earth's charge

A 70 kg man floats in freshwater with 3.2% of his volume above water when his lungs are empty, and 4.85% of his volume above water when his lungs are full.

Required:
a. Calculate the volume of air he inhales - called his lung capacity - in liters.
b. Does this lung volume seem reasonable?

Answers

Answer:

Explanation:

A) Vair = 1.3 L

B) Volume is not reasonable

Explanation:

A)

Assume

m to be total mass of the man

mp be the mass of the man that pulled out of the water

m1 be the mass above the water with the empty lung

m2 be the mass above the water with full lung

wp be the weight that the buoyant force opposes as a result of the air.

Va be the volume of air inside man's lungs

Fb be the buoyant force due to the air in the lung

given;

m = 78.5 kg

m1 = 3.2% × 78.5 = 2.5 kg

m2 = 4.85% × 78.5 = 3.8kg

But, mp = m2- m1

mp = 3.8 - 2.5

mp = 1.3kg

So using

Archimedes principle, the relation for formula for buoyant force as;

Fb = (m_displaced water)g = (ρ_water × V_air × g)

Where ρ_water is density of water = 1000 kg/m³

Thus;

Fb = wp = 1.3× 9.81

Fb = 12.7N

But

Fb = (ρ_water × V_air × g)

So

Vair = Fb/(ρ_water × × g)

Vair = 12.7/(1000 × 9.81)

V_air = 1.3 × 10^(-3) m³

convert to litres

1 m³ = 1000 L

Thus;

V_air = 1.3× 10^(-3) × 1000

V_air = 1.3 L

But since the average lung capacity of an adult human being is about 6-7litres of air.

Thus, the calculated lung volume is not reasonable

Explanation:

Select from the following for the next two questions:
A virtual, inverted and smaller than the object
B real, inverted and smaller than the object
C virtual, upright and smaller than the object
D real, upright and larger than the object
E virtual, upright and larger than the object
F real, inverted and larger than the object
G virtual, inverted and larger than the object
H real, upright and smaller than the object
An object is placed 46.9 cm away from a converging lens. The lens has a focal length of 10.0 cm. Select the statement from the list above which best describes the image an objesthse place 46.9 cm away from a spherical convex mirror. The radius of curvature of the mirror is 20.0 cm. Select the statement from the An object is placed 46.9 cm away from a spherical convex mirror. The radius of curvature of the mirror is 20.0 cm. Select the statement from the list above which best describes the image.

Answers

Answer:

Explanation:

1 )

An object is placed 46.9 cm away from a converging lens. The lens has a focal length of 10.0 cm.

Since the object is placed at a distance more than twice the focal length , its image will be inverted , real  and will be of the size less than the size of object . So option B is applied .

B)  real, inverted and smaller than the object.

2 )

An object is placed 46.9 cm away from a spherical convex mirror. The radius of curvature of the mirror is 20.0 cm.

The object is placed at a point beyond its radius of curvature, its image will be formed at a point between f and C   or between focal point and centre of curvature . Its size will be smaller than size of object and it will be real and inverted .

B)  real, inverted and smaller than the object.

You are walking around your neighborhood and you see a child on top of a roof of a building kick a soccer ball. The soccer ball is kicked at 31° from the edge of the building with an initial velocity of 15 m/s and lands 63 meters away from the wall. How tall, in meters, is the building that the child is standing on?

Answers

Answer:

69.58 m tall

Explanation:

Pls see attached file

Sammy is 5 feet and 5.3 inches tall.tall.what is sammy's height in metres?

Answers

Answer:

65.3

Explanation:

1 foot = 12 inches

Sammy is 5 feet tall.

5 feet = ? inches

Multiply the feet value by 12 to find in inches.

5 × 12

= 60

Add 5.3 inches to 60 inches.

60 + 5.3

= 65.3

Answer:

It will be 》》》》1.664716m

hi guys!!! i have no more points, can someone nice guess all of these for me? :)
1.What happens to the ocean water before the precipitation part of the water cycle
2.During which stage of the water cycle does water from the ocean form clouds?
3.what is a runoff??
4.Which statement about oceans is incorrect? A.Evaporation occurs when water is warmed by the sun. B.Most evaporation and precipitation occur over the ocean. C.97 percent of Earth's water is fresh water from the ocean. D.Water leaves the ocean by the process of evaporation
5.How does most ocean water return to the ocean in the water cycle

tysm to u who answers :)

Answers

1. The ocean water collects back in the ocean.

2. Condensation is the process by which water vapor in the air is changed into liquid water. Condensation is crucial to the water cycle because it is responsible for the formation of clouds.

3. an excessive amount of water flowing from downslope along earths surface

4. A.Evaporation occurs when water is warmed by the sun.

5. The water returns into the ocean by the water cycle . It evaporates , then it condensates , then it participates ( Rains ) and then goes back into the ocean.

Hope this answer correct ✌️

We've seen that for thermal radiation, the energy is of the form AVT4, where A is a universal constant, V is volume, and T is temperature. 1) The heat capacity CV also is proportional to a power of T, Tx. What is x

Answers

Answer:

this raise the temperature is x = 3

Explanation:

Heat capacity is the relationship between heat and temperature change

          C = Q / ΔT

if the heat in the system is given by the change in energy and we carry this differential formulas

          [tex]c_{v}[/tex] = dE / dT

In this problem we are told that the energy of thermal radiation is

        E = A V T⁴

Let's look for the specific heat

        c_{v} = AV 4 T³

the power to which this raise the temperature is x = 3

In a front-end collision, a 1500 kg car with shock-absorbing bumpers can withstand a maximumforce of 80 000 N before damage occurs. If the maximum speed for a non-damaging collision is4.0 km/h, by how much must the bumper be able to move relative to the car

Answers

Answer:

The bumper will be able to move by 0.01155m.

Explanation:

The magnitude of deceleration of the car in the front end collision.

[tex]a = \frac{F_m}{m} \\[/tex]

[tex]a = \frac{80000}{1500} \\[/tex]

[tex]a = 53.33[/tex]

This is the deceleration of the car that is generated to stop due to a front end collision.

4 km/h = 1.11 m/s

Now, the initial speed of the bumper in the relation of car, Vi = 0

Now, the initial speed of the bumper in the relation of car, Vf = 1.11 m/s

Use the below equation:

[tex]s = \frac{(Intitial \ speed)^2 – (Final \ speed)^2}{2a} \\[/tex]

[tex]s = \frac{(1.11)^2 – (0)}{2 \times 53.33} \\[/tex]

[tex]s = 0.01155 \\[/tex]

Thus, the bumper can move relative to the car is 0.01155 m .

A lens is made with a focal length of -40 cm using a material with index of refraction 1.50. A second lens is made with the SAME GEOMETRY as the first lens, but using a material having refractive index of 2.00. What is the focal length of the second lens

Answers

Answer:

 f = - 20 cm

Explanation:

This exercise asks us for the focal length, which for a lens in air is

                  1 / f = (n₂-n₁) (1 / R₁ - 1 / R₂)

where n₂ is the refractive index of the material, n₁ is the refractive index of the medium surrounding the lens, R₁ and R₂ are the radii of the two surfaces.

In this exercise the medium that surrounds the lens is air n₁ = 1 and the lens material has an index of refraction n₂ = n = 1.50, let's substitute in the expression

                 - 1/40 = (n-1) (1 / R₁ -1 / R₂)

                (1 / R₁ - 1 / R₂) = - 1/40 (n-1)

let's calculate

               (1 / R₁ -1 / R₂) = - 1/40 (1.50 -1)

               (1 / R₁ -1 / R₂) = -1/20

 Now we change the construction material for one with refractive index

n = 2, keeping the radii,

              1 / f = (n-1) (1 / R₁-1 / R₂)

              1 / f = (n-1) (-1/20)

               

let's calculate

             1 / f = (2.00-1) (-1/20)

              1 / f = -1/20

              f = - 20 cm

Types of friction in physics ​

Answers

-- static friction

-- kinetic friction

-- fluid friction

-- sliding friction

-- air resistance

-- drag

-- professional debate

By what length will a slab of concrete that is originally 18 m long contract when the temperature drops from 24°C to -16°C? The coefficient of linear thermal expansion for this concrete is 1.0 × 10-5 C-1.

Answers

Explanation:

According to Thermal Expansion of solids:

[tex]dl = \alpha \times l \times dt[/tex]

[tex]dl = {10}^{ - 5} \times 18 \times 40 [/tex]

[tex]dl = 7.2 \times {10}^{ - 3} [/tex]

A car travels at 45 km/h. If the driver breaks 0.65 seconds after seeing the traffic light turn yellow, how far will the car continue to travel before it begins to slow?

Answers

Answer:

8.1 m

Explanation:

Convert km/h to m/s.

45 km/h × (1000 m/km) × (1 h / 3600 s) = 12.5 m/s

Distance = speed × time

d = (12.5 m/s) (0.65 s)

d = 8.125 m

A clown 2 m tall looks at himself in a full-length mirror (floor-to-ceiling). Where in the mirror must he look to see his feet?

Answers

Answer:

Around the center of the mirror

Kinetic and
A brick is resting on a smooth wooden board that is at a 30° angle. What is one way to overcome the static friction that is holding the brick in place?
11 point)
O raise the board to a higher angle
O press down on the brick in a direction that is perpendicular to the board
O roughen up the texture of the wooden board
o lower the board so it's level with the ground

Answers

Answer:

raise the board to a higher angle

Explanation:

Static friction is the force opposite to the applied force.

Static friction is dependent on the angle of inclination, it means as the angle of incline increases, the force of friction will increases as normal force will decrease.

So, if the board will be raised to a higher angle, it will increase the angle of incline and will overcome the static friction and block will be able slide.

Hence, the correct option is "raise the board to a higher angle".

A circular conducting loop of radius 31.0 cm is located in a region of homogeneous magnetic field of magnitude 0.700 T pointing perpendicular to the plane of the loop. the loop is connected in series with a resistor of 265 ohms. The magnetic field is now increased at a constant rate by a factor of 2.30 in 29.0 s.

Calculate the magnitude of induced emf in the loop while the magnetic field is increasing.

With the magnetic field held constant a ts its new value of 1.61 T, calculate the magnitude of its induced voltage in the loop while it is pulled horizontally out of the magnetic field region during a time interval of 3.90s.

Answers

Answer:

(a) The magnitude of induced emf in the loop while the magnetic field is increasing is 9.5 mV

(b) The magnitude of the induced voltage at a constant magnetic field is 124.7 mV

Explanation:

Given;

radius of the circular loop, r = 31.0 cm = 0.31 m

initial magnetic field, B₁ = 0.7 T

final magnetic field, B₂ = 2.3B₁ = 2.3 X 0.7 T = 1.61 T

duration of change in the field, t = 29

(a) The magnitude of induced emf in the loop while the magnetic field is increasing.

[tex]E = A*\frac{\delta B}{\delta t} \\\\[/tex]

[tex]E = A*\frac{B_2 -B_1}{\delta t}[/tex]

Where;

A is the area of the circular loop

A = πr²

A = π(0.31)² = 0.302 m²

[tex]E = A*\frac{B_2 -B_1}{\delta t} \\\\E = 0.302*\frac{1.61-0.7}{29} \\\\E = 0.0095 \ V\\\\E = 9.5 \ mV[/tex]

(b) the magnitude of the induced voltage at a constant magnetic field

E = A x B/t

E = (0.302 x 1.61) / 3.9

E = 0.1247 V

E = 124.7 mV

Therefore, the magnitude of the induced voltage at a constant magnetic field is 124.7 mV

A laser emits photons having an energy of 3.74 × 10–19 J. What color would be expected for the light emitted by this laser? (c = 3.00 × 108 m/s, h = 6.63 × 10–34 J ⋅ s)

Answers

Answer:

The wavelength of the emitted photons 532 nm, corresponds to a visible light having GREEN color.

Explanation:

Given;

energy of the emitted photons, E = 3.74 x 10⁻¹⁹ J

speed of light, c = 3 x 10⁸ m/s

Planck's constant, h = 6.63 x 10⁻³⁴ J.s

The wavelength of the emitted light will be calculated by applying energy of photons;

[tex]E = hf[/tex]

where;

E is the energy emitted light

h is Planck's constant

f is frequency of the emitted photon

But f = c / λ

where;

λ is the wavelength of the emitted photons

[tex]E = \frac{hc}{\lambda} \\\\\lambda = \frac{hc}{E} \\\\\lambda = \frac{6.63*10^{-34} *3*10^{8}}{3.74*10^{-19}} \\\\\lambda = 5.318 *10^{-7} \ m\\\\\lambda = 531.8 *10^{-9} \ m\\\\\lambda = 531.8 \ nm[/tex]

λ ≅ 532 nm

the wavelength of the emitted photons is 532 nm.

Therefore, the wavelength of the emitted photons 532 nm, corresponds to a visible light having GREEN color.

Calculate the density of the following material.

1 kg helium with a volume of 5.587 m³
700 kg/m³
5.587 kg/m³
0.179 kg/m³

Answers

Answer:

[tex]density \: = \frac{mass}{volume} [/tex]

1 / 5.587 is equal to 0.179 kg/m³

Hope it helps:)

Answer:

The answer is

0.179 kg/m³

Explanation:

Density of a substance is given by

[tex]Density \: = \frac{mass}{volume} [/tex]

From the

mass = 1 kg

volume = 5.583 m³

Substitute the values into the above formula

We have

[tex]Density \: = \frac{1 \: kg}{5.583 \: {m}^{3} } [/tex]

We have the final answer as

Density = 0.179 kg/m³

Hope this helps you

Other Questions
-Speed is a scalar, a quantity that isdescribed byalone. Jose needs to find out how to delete cells from his workbook.Which method is the quickest way for Jose to get step-by-step directions?O Do research on the internet.O Press F1 and type "delete cells in the search bar.O Click the ? on the top-right corner in the Backstage View.O Type "delete cells in the Tell me what you want to do bar. The sum of the ages of Noi's and Noy's is 26 years. The different between four times Noi's age and two times Noy's age is 28 years. Find the age of Noi and Noy.WRITE AS AN EQUATION Which quadratic equation would be used to solve for the unknown dimensions?0 = 2w2512 = w2512 = 2w2512 = 2l + 2w _______ students go to college in their teens every year. A. A plenty of B. A good many C. A great deal of D. A lots of When we sleep, what does the brain replenish its stock for? How does efficiency lead to conformity? HELP ME PLEASEEE NOW!Which event from the story is the complicating incident?The narrator's editor has a family emergency on thenarrator's first day as a reporter.The narrator's job search is challenging because thejob market is in bad shape.The narrator is not completely sure which questionsto ask the principals, teachers, and parents.The narrator interviews for a job as a reporter eventhough she does not have a journalism background. When the number of units in work in process and finished goods inventories decrease, absorption costing net operating income will typically be greater than variable costing net operating income.a. Trueb. False 1. "Do you usually cook at home?"She2. "They had never been to Scotland until last year"She3. "Make sure you arrive early!"She4. "I should have studied harder for the exam"She5. "Would you mind telling me how to get to the art gallery, please?"She6. "Please don't forget my book"She7. "Make sure you arrive at six!"She8. "Remember to study hard!"She9. "Where do you want to eat tonight?"She10. "I usually drink coffee in the mornings"She11. 16. "Do you like studying English?"She12. 17. "I'll come and help you on Saturday"She13. 18. "Please buy some bread on your way home"She14. 19. "Please give thi. o John"She15. 20. "Could you give me the glass on the table, please?" What to understand about Passive voice How do earth's system interact to cycle organic matter? Write a statement that responds to the question HELP! Normally, the buyer's offer in a commercial transaction takes the form of:____________. 1. a phone call with the parties directly speaking with each other. 2. a personal letter. 3. a purchase order. 4. an acknowledgment form. How would you write The difference of 9 and the square of a number Solve the consumers problem for Johns optimal demand for Germ-X and Purell. (You should find actual numbers representing the quantity of Germ-X chosen and the quantity of in writing prose, how can you make sure that readers have a clear understanding of your meaning? Given below are two independent scenarios: a. Dream Co. has budgeted sales of $500,000, fixed costs are $240,000, and variable costs are $375,000. What is its contribution margin ratio? Enter the percentage amount as a whole number (for example, enter 10% as "10"). % b. Pearl Company has sales of $825,000, variable costs are 30% of sales, and fixed costs are $360,000. What is its operating profit? $ Why do you think that when subtracting a negativenumber, in reality you are adding it? (For example: 1-(-1) = 1+1=2) Read the summary of the section of "The Beginnings of the Maasai, where the volcanic eruption and its results are described. As a result of a volcanic eruption, Enkai and the cattle were thrown into the sky. Enkai wanted to save his cattle. He grew a tree that bridged the sky and the earth. The cattle walked down the tree to Neiterkob. Neiterkob and the Maasai tribe took over caring for the cattle. Why does the summary need to be revised? The summary incorrectly restates the central idea. The summary includes too many minor details. The summary lacks transitions that connect ideas. The summary is missing important words and phrases. Find n for the arithmetic sequence for which sn=345, u1=12 and d = 5 .