Answer:
The acceleration of the payload is 26 m/s2.
Explanation:
length, L = 65 cm = 0.65 m
angular acceleration = 40 rad/s^2
The acceleration is given by
a = angular acceleration x length
a = 40 x 0.65
a = 26 m/s^2
Hi can someon help me how to answer this?
Btw I'm from Philippines
Answer:
Test 1
1.True
2.True
3.True
4.False
5.True
6.True
7.False
8.True
9.True
10.True
yung iba nasa pic
In a television set the power needed to operate the picture tube comes from the secondary of a transformer. The primary of the transformer is connected to a 120-V receptacle on a wall. The picture tube of the television set uses 76 W, and there is 5.5 mA of current in the secondary coil of the transformer to which the tube is connected. Find the turns ratio Ns/Np of the transformer.
Ns/Np = ______.
Answer:
c) N_s / N_p = 115.15
Explanation:
Let's look for the voltage in the secondary, they do not indicate the power dissipated
P = V_s i
V_s = P / i
V_s = 76 / 5.5 10⁻³
V_s = 13.818 10³ V
the relationship between the primary and secondary of a transformer is
[tex]\frac{V_p}{N_p} = \frac{V_s}{N_s}[/tex]
[tex]\frac{N_s}{N_p} = \frac{V_s}{V_p}[/tex]
Ns / Np = 13,818 10³ /120
N_s / N_p = 115.15
How do the magnitudes of the currents through the full circuits compare for Parts I-III of this exercise, in which resistors are combined in series, in parallel, and in combination
Answer: hello tables and data related to your question is missing attached below are the missing data
answer:
a) I = I₁ = I₂ = I₃ = 0.484 mA
b) I₁ = 0.016 amps
I₂ = 0.0016 amps
I₃ = 7.27 * 10^-4 amps
c) I₁ = 1.43 * 10^-3 amp
I₂ = 0.65 * 10^-3 amps
Explanation:
A) magnitude of current for Part 1
Resistors are connected in series
Req = r1 + r2 + r3
= 3300 Ω ( value gotten from table 1 ) ,
V = 1.6 V ( value gotten from table )
hence I ( current ) = V / Req = 1.6 / 3300 = 0.484 mA
The magnitude of current is the same in the circuit
Vi = I * Ri
B) magnitude of current for part 2
Resistors are connected in parallel
V = 1.6 volts
Req = [ ( R1 * R2 / R1 + R2 ) * R3 / ( R1 * R2 / R1 + R2 ) + R3 ]
= [ ( 100 * 1000 / 100 + 1000) * 2200 / ( 100 * 1000 / 100 + 1000 ) + 2200]
= 87.30 Ω
For a parallel circuit the current flow through each resistor is different
hence the magnitude of the currents are
I₁ = V / R1 = 1.6 / 100 = 0.016 amps
I₂ = V / R2 = 1.6 / 1000 = 0.0016 amps
I₃ = V / R3 = 1.6 / 2200 = 7.27 * 10^-4 amps
C) magnitude of current for part 3
Resistors are connected in combination
V = 1.6 volts
Req = R1 + ( R2 * R3 / R2 + R3 )
= 766.66 Ω
Total current ( I ) = V / Req = 1.6 / 766.66 = 2.08 * 10^-3 amps
magnitude of currents
I₁ = ( I * R3 ) / ( R2 + R3 ) = 1.43 * 10^-3 amps
I₂ = ( I * R2 ) / ( R2 + R3 ) = 0.65 * 10^-3 amps
PLEASE HELP ME WITH THIS ONE QUESTION
What is the rest energy of a proton? (c = 2.9979 x 10^9 m/s, mp = 1.6726 x 10^-27)
[tex]E_0=1.5033×10^{-10}\:\text{J}[/tex]
Explanation:
The rest energy [tex]E_0[/tex] of a proton of mass [tex]m_p[/tex] is given by
[tex]E_0 = m_pc^2[/tex]
[tex]\:\:\:\:\:\:\:=(1.6726×10^{-27}\:\text{kg})(2.9979×10^8\:\text{m/s})^2[/tex]
[tex]\:\:\:\:\:\:\:=1.5033×10^{-10}\:\text{J}[/tex]
When a golfer tees off, the head of her golf club which has a mass of 158 g is traveling 48.2 m/s just before it strikes a 46.0 g golf ball at rest on a tee. Immediately after the collision, the club head continues to travel in the same direction but at a reduced speed of 32.7 m/s. Neglect the mass of the club handle and determine the speed of the golf ball just after impact.
Answer:
v₂ = 53.23 m/s
Explanation:
Given that,
The mass of a golf club, m₁ = 158 g = 0.158 kg
The initial speed of a golf club, u₁ = 48.2 m/s
The mass of a golf ball, m₂ = 46 g = 0.046 kg
It was at rest, u₂ = 0
Immediately after the collision, the club head continues to travel in the same direction but at a reduced speed of 32.7 m/s, v₁ = 32.7 m/s
We use the conservation of energy to find the speed of the golf ball just after impact as follows :
[tex]m_1u_1+m_2u_2=m_1v_1+m_2v_2\\\\v_2=\dfrac{m_1u_1-m_1v_1}{m_2}\\\\v_2=\dfrac{0.158(48.2)-0.158(32.7)}{0.046}\\\\=53.23\ m/s[/tex]
So, the speed of the golf ball just after the impact is equal to 53.23 m/s.
Light with a wavelength of 5.0 · 10-7 m strikes a surface that requires 2.0 ev to eject an electron. Calculate the energy, in joules, of one incident photon at this frequency. _____ joules 4.0 x 10 -19 4.0 x 10 -49 9.9 x 10 -32 1.1 x 10 -48
Answer:
pretty sure its 6.2 x 10^-13
Explanation:
I looked it up I'm not a bigbrain but want to help
A gymnast falls from a height onto a trampoline. For a moment, both the gymnast’s kinetic energy and gravitational potential energy are zero. How is the gymnast’s mechanical energy stored for that moment? Question 12 options: rest energy chemical energy elastic energy thermal energy
Answer:
elastic energy
Explanation:
When a gymnast falls on a trampoline from a height, after coming in contact with the trampoline, both the gymnast and the trampoline start to move down due to the elastic property of the trampoline.
During this stretching of the trampoline there comes a maximum point up to which the trampoline is stretched. At this point, both the kinetic energy and the gravitational potential energy of the gymnast are zero due to zero speed and zero height, respectively.
The only energy stored in the gymnast's body at this point is the elastic potential energy due to stretching of the trampoline. Hence,the correct option is:
elastic energy
Explain why the flow from the battery increases when the switch is closed. Give the label of the concept(s) that you use from the model of electricity. [
Answer:
Due to the applied filed the electrons move in a particular direction.
Explanation:
Initially when the switch is off, the free electrons move here and there in any random directions in the conductor with the random speeds called thermal velocity. So, tat the net flow is almost zero.
When the battery is connected is switch is ON, the random motion of the electrons aligned in a particular direction due to the force applied by the electric filed, so the net flow is not zero it increases and thus the current flow.
If one lawn mower causes an 80-dB sound level at a point nearby, four lawnmowers together would cause a sound level of ____________ at that point. a.92 dB b.84 dB c.86 dB d.none of the above
Answer:
The intensity of 4 lawn movers is 86 dB.
Explanation:
Intensity of one lawnmower = 80 dB
Let the intensity is I.
Use the formula of intensity
[tex]dB = 10 log\left ( \frac{I}{Io} \right )\\\\80=10log\left ( \frac{I}{Io} \right )\\\\10^8 = \frac{I}{10^{-12}}\\\\I = 10^{-4} W/m^2[/tex]
Now the intensity of 4 lawn movers is
[tex]dB = 10 log\left ( \frac{4I}{Io} \right )\\\\dB=10log\left ( \frac{4\times10^{-4}}{10^{-12}} \right )\\\\dB = 86 dB\\[/tex]
when blueshift occurs,the preceived frequency of the wave would be?
Answer:
When blueshift happens, the perceived frequency of the wave would be higher than the actual frequency.
Explanation:
As the name suggests, when blueshift happens to electromagnetic waves, the frequency of the observed wave would shift towards the blue (high-frequency) end of the visible spectrum. Hence, there would be an increase to the apparent frequency of the wave.
Blueshifts happens when the source of the wave and the observer are moving closer towards one another.
Assume that the wave is of frequency [tex]f\; {\rm Hz}[/tex] at the source. In other words, the source of the wave sends out a peak after every [tex](1/f)\; {\text{seconds}}[/tex].
Assume that the distance between the observer and the source of the wave is fixed. It would then take a fixed amount of time for each peak from the source to reach the observer.
The source of this wave sends out a peak after each period of [tex](1/f)\; {\text{seconds}}[/tex]. It would appear to the observer that consecutive peaks arrive every [tex](1/f)\; {\text{seconds}}\![/tex]. That would correspond to a frequency of [tex]f\; {\rm Hz}[/tex].
On the other hand, for a blueshift to be observed, the source of the wave needs to move towards the observer. Assume that the two are moving towards one another at a constant speed of [tex]v \; {\rm m \cdot s^{-1}}[/tex].
Again, the source of this wave would send out a peak after each period of [tex](1/f)\; {\text{seconds}}[/tex]. However, by the time the source sends out the second peak, the source would have been [tex]v \cdot (1 / f) \; { \rm m}= (v / f)\; {\rm m}[/tex] closer to the observer then when the source sent out the first peak.
When compared to the first peak, the second peak would need to travel a slightly shorter distance before it reach the observer. Hence, from the perspective of the observer, the time difference between the first and the second peak would be shorter than [tex](1/f)\; {\text{seconds}}[/tex]. The observed frequency of this wave would be larger than the original [tex]f\; {\rm Hz}[/tex].
A submarine has a "crush depth" (that is, the depth at which
water pressure will crush the submarine) of 400 m. What is
the approximate pressure (water plus atmospheric) at this
depth? (Recall that the density of seawater is 1025 kg/m3, g=
9.81 m/s2, and 1 kg/(m-s2) = 1 Pa = 9.8692 x 10-6 atm.)
Answer:
P =40.69 atm
Explanation:
We need to find the approximate pressure at a depth of 400 m.
It can be calculated as follows :
P = Patm + ρgh
Put all the values,
[tex]P=1\ atm+1025 \times 9.81\times 400\times 9.8692\times 10^{-6}\ atm/Pa\\\\P=40.69\ atm[/tex]
So, the approximate pressure is equal to 40.69 atm.
Cold air rises because it is denser than water, is this true?
Answer:
true
Explanation:
im not sure please dont attack me
Solids diffuse because the particles cannot move.
A. Can
B. Not enough info
C. Cannot
D. Sometimes will
Solids cannot diffuse.
Part of your electrical load is a 60-W light that is on continuously. By what percentage can your energy consumption be reduced by turning this light off
Answer:
Following are the solution to the given question:
Explanation:
Please find the complete question in the attached file.
The cost after 30 days is 60 dollars. As energy remains constant, the cost per hour over 30 days will be decreased.
[tex]\to \frac{\$60}{\frac{30 \ days}{24\ hours}} = \$0.08 / kwh.[/tex]
Thus, [tex]\frac{\$0.08}{\$0.12} = 0.694 \ kW \times 0.694 \ kW \times 1000 = 694 \ W.[/tex]
The electricity used is continuously 694W over 30 days.
If just resistor loads (no reagents) were assumed,
[tex]\to I = \frac{P}{V}= \frac{694\ W}{120\ V} = 5.78\ A[/tex]
Energy usage reduction percentage = [tex](\frac{60\ W}{694\ W} \times 100\%)[/tex]
This bulb accounts for [tex]8.64\%[/tex] of the energy used, hence it saves when you switch it off.
A person with a near point of 85 cm, but excellent distant vision, normally wears corrective glasses. But he loses them while traveling. Fortunately, he has his old pair as a spare.
(a) If the lenses of the old pair have a power of +2.25 diopters, what is his near point (measured from his eye) when he is wearing the old glasses if they rest 2.0 cm in front of his eye?
(b) What would his near point be if his old glasses were contact lenses instead?
Answer:
a) p = 95.66 cm, b) p = 93.13 cm
Explanation:
For this problem we use the constructor equation
[tex]\frac{1}{f} = \frac{1}{p} + \frac{1}{q}[/tex]
where f is the focal length, p and q are the distances to the object and the image, respectively
the power of the lens is
P = 1 / f
f = 1 / P
f = 1 / 2.25
f = 0.4444 m
the distance to the object is
[tex]\frac{1}{p} = \frac{1}{f} -\frac{1}{q}[/tex]
the distance to the image is
q = 85 -2
q = 83 cm
we must have all the magnitudes in the same units
f = 0.4444 m = 44.44 cm
we calculate
[tex]\frac{1}{p} = \frac{1}{44.44} - \frac{1}{83}[/tex]
1 / p = 0.010454
p = 95.66 cm
b) if they were contact lenses
q = 85 cm
[tex]\frac{1}{p} = \frac{1}{44.44} - \frac{1}{85}[/tex]
1 / p = 0.107375
p = 93.13 cm
a vechile having a mass of 500kg is moving with a speed of 10m/s.Sand is dropped into it at the rate of 10kg/min.What force is needed to keep the vechile moving with uniform speed
Answer:
1.67 N
Explanation:
Applying,
F = u(dm/dt)+m(du/dt)................ Equation 1
Where F = force, m = mass of the vehicle, u = speed.
Since u is constant,
Therefore, du/dt = 0
F = u(dm/dt)............... Equation 2
From the question,
Given: u = 10 m/s, dm/dt = 10 kg/min = (10/60) kg/s
Substitute these values into equation 2
F = 10(10/60)
F = 100/60
F = 1.67 N
A car is moving at a speed of 60 mi/hr (88 ft/sec) on a straight road when the driver steps on the brake pedal and begins decelerating at a constant rate of 10ft/s2 for 3 seconds. How far did the car go during this 3 second interval?
Answer:
219 ft
Explanation:
Here we can define the value t = 0s as the moment when the car starts decelerating.
At this point, the acceleration of the car is given by the equation:
A(t) = -10 ft/s^2
Where the negative sign is because the car is decelerating.
To get the velocity equation of the car, we integrate over time, to get:
V(t) = (-10 ft/s^2)*t + V0
Where V0 is the initial velocity of the car, we know that this is 88 ft/s
Then the velocity equation is:
V(t) = (-10 ft/s^2)*t + 88ft/s
To get the position equation we need to integrate again, this time we get:
P(t) = (1/2)*(-10 ft/s^2)*t^2 + (88ft/s)*t + P0
Where P0 is the initial position of the car, we do not know this, but it does not matter for now.
We want to find the total distance that the car traveled in a 3 seconds interval.
This will be equal to the difference in the position at t = 3s and the position at t = 0s
distance = P(3s) - P(0s)
= ( (1/2)*(-10 ft/s^2)*(3s)^2+ (88ft/s)*3s + P0) - ( (1/2)*(-10 ft/s^2)*(0s)^2 + (88ft/s)*0s + P0)
= ( (1/2)*(-10 ft/s^2)*9s^2+ (88ft/s)*3s + P0) - ( P0)
= (1/2)*(-10 ft/s^2)*9s^2+ (88ft/s)*3s = 219ft
The car advanced a distance of 219 ft in the 3 seconds interval.
A 0.20 mass on a horizontal spring is pulled back a certain distance and released. The maximum speed of the mass is measured to be 0.20 . If, instead, a 0.40 mass were used in this same experiment, choose the correct value for the maximum speed.
a. 0.40 m/s.
b. 0.20 m/s.
c. 0.28 m/s.
d. 0.14 m/s.
e. 0.10 m/s.
Answer:
d
Explanation:
Ya gon find the Kenitic Energy first
K=½mv²===> K=½×0.2×(0.2)²===> 0.1(0.04)===> 0.004
and now the replacement:
0.004=½×0.4V²====> v²=0.02===> V=0.14m/s
A typical incandescent light bulb consumes 75 W of power and has a mass of 20 g. You want to save electrical energy by dropping the bulb from a height great enough so that the kinetic energy of the bulb when it reaches the floor will be the same as the energy it took to keep the bulb on for 2.0 hours. From what height should you drop the bulb, assuming no air resistance and constant g?
Answer:
h = 2755102 m = 2755.102 km
Explanation:
According to the given condition:
Potential Energy = Energy Consumed by Bulb
[tex]mgh = Pt\\\\h = \frac{Pt}{mg}[/tex]
where,
h = height = ?
P = Power of bulb = 75 W
t = time = (2 h)(3600 s/1 h) = 7200 s
m = mass of bulb = 20 g = 0.02 kg
g = acceleration due to gravity = 9.8 m/s²
Therefore,
[tex]h = \frac{(75\ W)(7200\ s)}{(0.02\ kg)(9.8\ m/s^2)}[/tex]
h = 2755102 m = 2755.102 km
A mass attached to the end of a spring is oscillating with a period of 2.25 s on a horizontal frictionless surface. The mass was released from rest at
t = 0
from the position
x = 0.0480 m.
Determine the location of the mass at
t = 5.85 s?
Answer:
[tex]X=0.0389m[/tex]
Explanation:
From the question we are told that:
Period of spring [tex]T_s=2.25s[/tex]
Initial Position of Mass [tex]x=0.0480m[/tex]
Final Mass period [tex]T_f=5.85s[/tex]
Generally the equation for the Mass location is mathematically given by
[tex]X=xcos*\frac{2\pi T_s}{T_f}[/tex]
[tex]X=0.048*cos*\frac{2\pi 5.85}{2.25}[/tex]
[tex]X=0.0389m[/tex]
g As they reach higher temperatures, most semiconductors... Selected Answer: have an increased resistance. Answers: have a constant resistance. have an increased resistance. have a decreased resistance.
Answer:
have an increased resistance
Stars have different colors. What causes stars to have colors?
A. location
B. temperature
C. oxygen
D. carbon dioxide
Answer:
temperature
Explanation:
temperature change forms different elements and different element sustain different colour
1. Which one of the following is not an organic compound? Why? CH4 C2H6O CaO
2. Fill in the chart below to identify and describe the functional groups associated with organic chemistry. Name General Structure Properties/Uses Alcohol Aldehyde Ketone Fatty acid Ether
3. Explain why carbon is called “the backbone” molecule of organic chemistry and why organic molecules couldn't easily be based on H or O instead.
Answer:
1. CaO is not an organic compound because it doesn’t contain a carbon molecule.
2.
Name General Structure Properties/Uses
Alcohol R-OH (contains a hydroxyl group) Can be poisonous, can be made from fermentation or distillation
Aldehyde R-COH (contains a carbon atom double-bonded to an oxygen and single-bonded to a hydrogen) Makes up formaldehyde and acetaldehyde
Ketone R-CO-R (contains a carbon atom double-bonded to an oxygen atom and then connected to carbon chains through the other two single bonds) Makes up acetone
Fatty acid R-COOH (contains a carbon atom double-bonded to an oxygen atom, single-bonded to a hydroxyl, and single-bonded to the carbon chain) Makes up fatty acids like acetic acid and stearic acid; used to form esters
Ether R-O-R (contains double carbon chains connected to an oxygen atom through single bonds) Ethyl ether is very volatile and flammable, used in veterinary medicine
3. Carbon is able to make four covalent bonds with other elements. This gives it a lot of diversity and the ability to form differently shaped molecules that perform specific functions or fit specific cell receptors in the body. H can form only one bond, and oxygen forms only two bonds, so they don't have as much potential to form a good starting point for organic molecules.
Explanation:
pf
CaO is not an organic compound because it doesn’t contain a carbon molecule.
Name General Structure Properties/Uses(which contains a hydroxyl group) Can be poisonous, can be made from fermentation or distillation
Aldehyde R-COH (contains a carbon atom double-bonded to oxygen and single-bonded to hydrogen) Makes up formaldehyde and acetaldehyde
Ketone R-CO-1R (contains a carbon atom double-bonded to an oxygen atom and then connected to carbon chains through the other two single bonds) Makes up acetone
Fatty acid R-COOH (contains a carbon atom double-bonded to an oxygen atom, single-bonded to a hydroxyl, and single-bonded to the carbon chain) Makes up fatty acids like acetic acid and stearic acid; used to form esters11
Ether -O-R (contains double carbon chains connected to an oxygen atom through single bonds) Ethyl ether is very volatile and flammable, used in veterinary medicine
Carbon can make four covalent bonds with other elements. This gives it a lot of diversity and the ability to form differently shaped molecules that perform specific functions or fit specific cell receptors in the body. H can form only one bond, and oxygen forms only two bonds, so they don't have as much potential to form a good starting point for organic molecules.
Learn more about organic molecules.
https://brainly.com/question/24225576
#SPJ2
Topic: Chapter 10: Projectory or trajectile?
Projectile range analysis:
A projectile is launched from the ground at 10 m/s, at
an angle of 15° above the horizontal and lands 5.1 m away.
What other angle could the projectile be launched at, with the same velocity,
and land 5.1 m away?
90°
75°
45
50°
30°
Answer:
The other angle is 75⁰
Explanation:
Given;
velocity of the projectile, v = 10 m/s
range of the projectile, R = 5.1 m
angle of projection, 15⁰
The range of a projectile is given as;
[tex]R = \frac{u^2sin(2\theta)}{g}[/tex]
To find another angle of projection to give the same range;
[tex]5.1 = \frac{10^2 sin(2\theta)}{9.81} \\\\100sin(2\theta) = 50\\\\sin(2\theta) = 0.5\\\\2\theta = sin^{-1}(0.5)\\\\2\theta = 30^0\\\\\theta = 15^0\\\\since \ the \ angle \ occurs \ in \ \ the \ first \ quadrant,\ the \ equivalent \ angle \\ is \ calculated \ as;\\\\90- \theta = 15^0\\\\\theta = 90 - 15^0\\\\\theta = 75^0[/tex]
Check:
sin(2θ) = sin(2 x 75) = sin(150) = 0.5
sin(2θ) = sin(2 x 15) = sin(30) = 0.5
Give an example of a substance with an amorphous structure.
Answer:
Tempered glass
Explanation:
When warmed, an amorphous substance has a non-crystalline architecture that differentiates from its isochemical liquid, but this does not go through structural breakdown or the glass transition.
In the following calculations, be sure to express the answer in standard scientific notation with the appropriate number of
significant figures.
3.88 x 1079 - 4.701 x 1059
x 10
g
Answer:
-45,597.07
Explanation:
if not in scientific calculator and yung answer nung sa scientific sa comment na lang dinadownload ko ka eh
Two plastic bowling balls, 1 and 2, are rubbed with cloth until they each carry a uniformly distributed charge of magnitude 0.50 nC . Ball 1 is negatively charged, and ball 2 is positively charged. The balls are held apart by a 900-mm stick stuck through the holes so that it runs from the center of one ball to the center of the other.
Required:
What is the magnitude of the dipole moment of the arrangement?
Answer:
The right solution is "[tex]4.5\times 10^{-10} \ Cm[/tex]".
Explanation:
Given that,
q = 0.50 nC
d = 900 mm
As we know,
⇒ [tex]P=qd[/tex]
By putting the values, we get
⇒ [tex]=0.50\times 900[/tex]
⇒ [tex]=(0.50\times 10^{-9})\times 0.9[/tex]
⇒ [tex]=4.5\times 10^{-10} \ Cm[/tex]
Answer:
The dipole moment is 4.5 x 10^-10 Cm.
Explanation:
Charge on each ball, q = 0.5 nC
Length, L = 900 mm = 0.9 m
The dipole moment is defined as the product of either charge and the distance between them.
It is a vector quantity and the direction is from negative charge to the positive charge.
The dipole moment is
[tex]p = q L\\\\p = 0.5 \times 10^{-9}\times 0.9\\\\p = 4.5\times 10^{-10} Cm[/tex]
Question: A NEO distance from the Sun is 1.17 AU. What is the speed of the NEO (round your answer to 2 decimal places)
Answer:
v = 2.75 10⁴ m / s
Explanation:
For this exercise we must use Kepler's third law which is an application of Newton's second law to the solar system
F = ma
where force is the force of gravity
F = [tex]G \frac{m M}{r^2}[/tex]
acceleration is centripetal
a = [tex]\frac{v^2}{r}[/tex]
we substitute
G m M / r² = m v² / r
[tex]\frac{GM}{r}[/tex] = v²
v = [tex]\sqrt{GM/r}[/tex]
indicate that the radius of the orbit is r = 1.17 AU, let's reduce to the SI system
r = 1.17 AU (1.496 10¹¹ m / 1 AI) = 1.76 10¹¹ m
let's calculate
v = [tex]\sqrt{\frac{6.67 \ 10^{-11} 1.991 \ 10^{30} }{ 1.76 \ 10^{11}} }[/tex]Ra (6.67 10-11 1.991 10 30 / 1.76 10 11
v = [tex]\sqrt{7.5454 \ 10^8 }[/tex]ra 7.5454 10 8
v = 2.75 10⁴ m / s
Can you think of reasons why the charge on each ball decreases over time and where the charges might go
Answer:
By the principle of corona discharge.
Explanation:
The charge on each ball will decreases over time due to the electrical discharge in air.
According to the principle of corona discharge, when the curvature is small, the discharge of the charge takes placed form the pointed ends.
An object is 2.0 cm from a double convex lens with a focal length of 1.5 cm. Calculate the image distance
Answer:
0.857 cm
Explanation:
We are given that:
The focal length for a convex lens to be (f) = 1.5cm
The object distance (u) = - 2.0 cm
We are to determine the image distance (v) = ??? cm
By applying the lens formula:
[tex]\dfrac{1}{f} = \dfrac{1}{u}+\dfrac{1}{v}[/tex]
By rearrangement and making (v) the subject of the above formula:
[tex]v = \dfrac{uf}{u-f}[/tex]
replacing the given values:
[tex]v = \dfrac{(-2.0)(1.5)}{(-2.0 -1.5)}[/tex]
[tex]v = \dfrac{-3.0}{(-3.5)}[/tex]
v = 0.857 cm
