Answer:
We can think the water stream as a solid object that is fired.
The distance between the fireperson and the building is 50m. (i consider that the position of the fireperson is our position = 0)
The angle is 30 above the horizontal. (yo wrote 300, but this has no sense because 300° implies that he is pointing to the ground).
The initial speed of the stream is 40m/s.
First, using the fact that:
x = R*cos(θ)
y = R*sin(θ)
in this case R = 40m/s and θ = 30°
We can use the above relation to find the components of the velocity:
Vx = 40m/s*cos(30°) = 34.64m/s
Vy = 20m/s.
First step:
We want to find the time needed to the stream to hit the buildin.
The horizontal speed is 34.64m/s and the distance to the wall is 50m
So we want that:
34.64m/s*t = 50m
t = 50m/(34.64m/s) = 1.44 seconds.
Now we need to calculate the height of the stream at t = 1.44s
Second step:
The only force acting on the water is the gravitational one, so the acceleration of the stream is:
a(t) = -g.
g = -9.8m/s^2
For the speed, we integrate over time and we get:
v(t) = -g*t + v0
where v0 is the initial speed: v0 = 20m/s.
The velocity equation is:
v(t) = -g*t + 20m/s.
For the position, we integrate again over time:
p(t) = -(1/2)*g*t^2 + 20m/s*t + p0
p0 is the initial height of the stream, this data is not known.
Now, the height at the time t = 1.44s is
p(1.44s) = -5.9m/s^2*(1.44s)^2 + 20m/s*1.44s + po
= 16.57m + p0
So the height at wich the stream hits the building is 16.57 meters above the initial height of the fire hose.
At what minimum angle will you get total internal reflection of light traveling in diamond and reflected from ethanol? °
Answer:
34°
Using the relation
θᶜ = sin^-1(n₂/n₁),
where n1= the refractive index of light is propagating from a medium
And n2 = refractive index of medium into which light is entering
So we know that
refractive index of diamond at 589nm = 2.41= n₁
refractive index of ethanol at 589nm and 20°C = 1.36= n₂
Thus. θᶜ = sin^-1(1.361/2.417) = 0.58radians = 34°
Explanation:
Rod cells in the retina of the eye detect light using a photopigment called rhodopsin. 1.8 eV is the lowest photon energy that can trigger a response in rhodopsin. Part A What is the maximum wavelength of electromagnetic radiation that can cause a transition
Answer:
The maximum wavelength of the e-m wave is 6.9 x 10^-7 m
Explanation:
Energy required to trigger a response = 1.8 eV
we convert to energy in Joules.
1 eV = 1.602 x 10^-19 J
1.8 eV = [tex]x[/tex] J
[tex]x[/tex] = 1.8 x 1.602 x 10^-19 = 2.88 x 10^-19 J
The energy of an electromagnetic wave is gotten as
E = hf
where
h is the Planck's constant = 6.63 x 10^-34 J-s
and f is the frequency of the wave.
substituting values, we have
2.88 x 10^-19 = 6.63 x 10^-34 x f
f = (2.88 x 10^-19)/(6.63 x 10^-34)
f = 4.34 x 10^14 Hz
We know that the frequency of an e-m wave is given as
f = c/λ
where
c is the speed of light = 3 x 10^8 m/s
λ is the wavelength of the e-m wave
From this we can say that
λ = c/f
λ = (3 x 10^8)/(4.34 x 10^14)
λ = 6.9 x 10^-7 m
Water pressurized to 3.5 x 105 Pa is flowing at 5.0 m/s in a horizontal pipe which contracts to 1/2 its former radius. a. What are the pressure and velocity of the water after the contraction
Answer:
Explanation:
Using the Continuity equation
v X A = v' xA'
so if A is 1/2of A' then A velocity must be 2 times the A'
after-contraction v = 2 x 5.0m/s = 10m/s
Using the Bernoulli equation
p₁ + ½ρv₁² + ρgh₁ = p₂ + ½ρv₂² + ρgh₂
, the "h" terms cancel
3.5 x 10^ 5Pa + ½ x 1000kg/m³x (5.0m/s)² = p₂ + ½ x 1000kg/m³ x (10m/s)²
p₂ = 342500pa
Which of the following explains why a “control” is important in a case-control study of a disease? The researchers need to control the bias that those who contracted the disease may create when they talk to others. The researchers need to compare those who contracted the disease to those who did not. The researchers need to compare those who contracted the disease to those who contracted previous diseases. The researchers need to control the disease so that it is not spread further.
The researchers need to compare those who contracted the disease to those who did not.
Consider a series RLC circuit where R=25.0 Ω, C=35.5 μF, and L=0.0940 H, that is driven at a frequency of 70.0 Hz. Determine the phase angle ϕ of the circuit in degrees.
Answer:
137.69°Explanation:
The phase angle of an RLC circuit ϕ is expressed as shoen below;
ϕ = [tex]tan^{-1} \dfrac{X_l-X_c}{R}[/tex]
Xc is the capacitive reactance = 1/2πfC
Xl is the inductive reactance = 2πfL
R is the resistance = 25.0Ω
Given C = 35.5 μF, L = 0.0940 H, and frequency f = 70.0Hz
Xl = 2π * 70*0.0940
Xl = 41.32Ω
For the capacitive reactance;
Xc = 1/2π * 70*35.5*10⁻⁶
Xc = 1/0.0156058
Xc = 64.08Ω
Phase angle ϕ = [tex]tan^{-1} \frac{41.32-64.08}{25} \\\\[/tex]
ϕ = [tex]tan^{-1} \frac{-22.76}{25} \\\\\\\\[/tex]
[tex]\phi = tan^{-1} -0.9104\\\\\phi = -42.31^0[/tex]
Since tan is negative in the 2nd quadrant;
[tex]\phi = 180-42.31^0\\\\\phi = 137.69^0[/tex]
Hence the phase angle ϕ of the circuit in degrees is 137.69°
The phase angle ϕ of the series RLC circuit that is driven at a frequency of 70.0 Hz is ϕ = 137.69°
Phase angle:Given that:
capacitance C = 35.5 μF,
Inductance L = 0.0940 H,
The resistance R = 25.0Ω
and frequency f = 70.0Hz
The capacitive reactance is given by:
Xc = 1/2πfC
Xc = 1/2π × 70 × 35.5× 10⁻⁶
Xc = 1/0.0156058
Xc = 64.08Ω
The inductive reactance is given by:
Xl = 2πfL
Xl = 2π × 70 × 0.0940
Xl = 41.32Ω
The phase angle of an RLC circuit ϕ is given by:
[tex]\phi=tan^{-1}\frac{X_l-X_c}{R}\\\\\phi=tan^{-1}\frac{41.32-64.08}{25}[/tex]
Ф = -42.31°
Since tan is negative in the 2nd quadrant, thus:
ϕ = 180° - 42.31°
ϕ = 137.69°
Learn more about RLC circuit:
https://brainly.com/question/372577?referrer=searchResults
Water pressurized to 3.5 x 105 Pa is flowing at 5.0 m/s in a horizontal pipe which contracts to 1/3 its former area. What are the pressure and velocity of the water after the contraction
Answer:
the pressure after contraction is 2×10^5 Pa
the speed after contraction is 15m/s
Explanation:
We were given Pressure P to be 3.5 x 10^5 that is Flowing with speed of 5.0 m/s,
For us to calculate pressure we need to calculate the area first as;
Let initial Area = A₁
And Final area A₂
We were told that in a horizontal pipe it contracts to 1/3 its former area. Which means
A₂= A₁/3.................
V₁ is the speed
the pressure and speed of the water after the contraction can be calculated using equation of continuity below
A₂V₂ = A₁V₁
But
If we substitute given value in the expresion we have
V₂ = (3A *5)/A
V₂ = 15m/s
Therefore, the speed after contraction is 15m/s
Now we can calculate the pressure using
Bernoulli's equation
p₁ + ½ρv₁² + ρgh₁ = p₂ + ½ρv₂² + ρgh₂
But we know that the pipe is horizontal, then "h" terms cancel out then
p₁ + ½ρv₁² = p₂ + ½ρv₂²
Making P₂ subject of formula we have
p₂ = 0.5ρ( V ₁² - v₂² ) + P₁
P₂=. 0.5 × 1000 (5² -15² ) + 3*10^5
=2×10^5 Pa
Therefore, the pressure after contraction is 2×10^5 Pa
(a) the final speed of the water after contraction is 15 m/s.
(b) The final pressure of the water after contraction is 2.5 x 10⁵ Pa.
The given parameters;
initial pressure, P₁ = 3.5 x 10⁵ Painitial speed, v₁ = 5 m/sdensity of water, ρ = 1000 kg/m³Let the initial area of the pipe = A₁
Apply the continuity equation to determine the final speed of the water after contraction as follows;
[tex]A_1 V_1 = A_2 V_2\\\\V_2 = \frac{A_1V_1}{A_2} \\\\V_2 = \frac{A_1 \times 5}{\frac{1}{3} A_1 } \\\\V_2 = 15 \ m/s[/tex]
The final pressure of the water after contraction is determined by applying Bernoulli's equation for horizontal pipe;
[tex]P_1 + \frac{1}{2} \rho V_1^2= P_2 + \frac{1}{2} \rho V_2^2\\\\P_2 = \frac{1}{2} \rho (V_1^2 - V_2^2) + P_1\\\\P_2 = \frac{1}{2} \times 1000(5^2 - 15^2) + 3.5 \times 10^5\\\\P_2 = 2.5 \times 10^5 \ Pa[/tex]
Learn more here:https://brainly.com/question/19566865
A fish is 80 cm below the surface of a pond. What is the apparent depth (in cm) when viewed from a position almost directly above the fish
Answer:
Apparent depth (Da) = 60.15 cm (Approx)
Explanation:
Given:
Distance from fish (D) = 80 cm
Find:
Apparent depth (Da)
Computation:
We know that,
Refractive index of water (n2) = 1.33
So,
Apparent depth (Da) = D(n1/n2)
Apparent depth (Da) = 80 (1/1.33)
Apparent depth (Da) = 60.15 cm (Approx)
The apparent depth of the fish is 60 cm.
To calculate the apparent depth of the fish, we use the formula below.
Formula:
R.F(water) = Real depth(D)/Apparent depth(D')R.F = D/D'.................... Equation 1Where:
R.F = Refractive index of waterMake D' The subject of the equation.
D' = D/R.F................... Equation 2From the question,
Given:
D = 80 cmR.F = 1.333Substitute these values into equation 2
D' = 80/1.33D' = 60.01D' = 60 cmHence, the apparent depth of the fish is 60 cm
Learn more about apparent depth here: https://brainly.com/question/24319677
A red card is illuminated by red light. Part A What color will the card appear? What color will the card appear? a. Red b. Black c. White d. Green
The color that is reflected when a red card is illuminated by red light is white.
The color an object is perceived to have, depends on the frequency of light it reflects.
If white light incidents on a red filter, red is transmitted while blue and green are absorbed.
Consequently, when a red card is illuminated by red light, the red card will reflect back almost all the incident light on it, causing it to appear brighter which creates an illusion of white color to the eyes.
Thus, we can conclude the color that is reflected when a red card is illuminated by red light is white.
Learn more here:https://brainly.com/question/3495999
If you wish to observe features that are around the size of atoms, say 5.5 × 10^-10 m, with electromagnetic radiation, the radiation must have a wavelength of about the size of the atom itself.
Required:
a. What is its frequency?
b. What type of electromagnetic radiation might this be?
Answer:
a) 5.5×10^17 Hz
b) visible light
Explanation:
Since the wavelength of the electromagnetic radiation must be about the size of the about itself, this implies that;
λ= 5.5 × 10^-10 m
Since;
c= λ f and c= 3×10^8 ms-1
f= c/λ
f= 3×10^8/5.5 × 10^-10
f= 5.5×10^17 Hz
The electromagnetic wave is visible light
A windmill on a farm rotates at a constant speed and completes one-half of a rotation in 0.5 seconds. What is its rotation speed
Answer:
v = 6.28 m/s
Explanation:
It is given that,
A windmill on a farm rotates at a constant speed and completes one-half of a rotation in 0.5 seconds,
Number of revolution is half. It means angular velocity is 3.14 radians.
Let v is the angular speed. So,
[tex]v=\dfrac{\omega}{t}\\\\v=\dfrac{3.14}{0.5}\\\\v=6.28\ m/s[/tex]
So, the rotation speed is 6.28 m/s.
The angular velocity is the rotation speed, which is the angle of rotation
of the windmill per second, which is 2·π radians.
Response:
The rotation speed is 2·π rad/sHow can the rotational speed of the windmill be calculated?The given parameter are;
The angle of rotation the windmill rotates in 0.5 seconds = One-half a
rotation.
Required:
The rotational speed (angular velocity)
Solution:
The angle of one rotation = 2·π radians
Angle of one-half ration = [tex]\frac{1}{2}[/tex] × 2·π radians = π radians
[tex]Rotational \ speed = \mathbf{\dfrac{Angle \ of \ rotation}{Time}}[/tex]
Which gives;
[tex]Rotational \ speed, \omega = \dfrac{\pi}{0.5 \ s} = \mathbf{2 \cdot \pi \ rad/s}[/tex]
The rotation speed is 2·π rad/sLearn more about rotational speed here:
https://brainly.com/question/6969329
An electric train operates on 800 V. What is its power consumption when the current flowing through the train's motor is 2,130 A?
Answer:
1704 kWExplanation:
To solve for the power consumed by the trains motor we have to employ the formula for power which is
Power= current * voltage
Given that
voltage V= 800 V
current I= 2130 A
Substituting in the formula for power we have
Power= 2130*800= 1704000 watt
Power = 1704 kW
This is the amount of energy consumed, transferred or converted per unit of time
Hence the power consumed by the trains motor is 1704 kW
Terms to describe the opposition by a material.to being magnetised is
Answer:
Repulsion
Explanation:
Convert 76.2 kilometers to meters?
Answer
76200meters
Explanation:
we know that 1km=1000meters
to convert km into meters we we divide km by meters
=76.2/1000
=76200meters
Which is one criterion that materials of a technological design should meet? They must be imported. They must be affordable. They must be naturally made. They must be locally produced.
Answer:
they must be affordable because they have to pay for it or they wont get the stuff they are bying.
Explanation:
need a brainliest please.
Answer: B, they must be affordable.
Explanation:
A baseball (m=145g) traveling 35 m/s moves a fielder's glove backward 23 cm when the ball is caught. What was the average force exerted by the ball on the glove?
Answer:
386.13 N
Explanation:
The kinetic energy of the baseball is converted into workdone in moving the glove backward( work energy theorem).
Therefore, KE of the ball
[tex]\frac{1}{2} mv^2 =\frac{1}{2}(0.145)35^2\\ = 88.81 \text{J}[/tex]
Now, workdone in moving the glove
W= Fd
where F = Force applied, d = displacement of the glove= 0.23 cm.
88.81 = F×0.23
F= 88.81/0.23 = 386.13 N
A golfer hits a 42 g ball, which comes down on a tree root and bounces straight up with an initial speed of 15.6 m/s. Determine the height the ball will rise after the bounce. Show all your work.
Answer:
12.2 m
Explanation:
Given:
v₀ = 15.6 m/s
v = 0 m/s
a = -10 m/s²
Find: Δy
v² = v₀² + 2aΔy
(0 m/s)² = (15.6 m/s)² + 2 (-10 m/s²) Δy
Δy = 12.2 m
[tex] \LARGE{ \boxed{ \rm{ \green{Answer:}}}}[/tex]
Given,
The initial speed is 15.6 m/s The mass of the ball is 42g = 0.042kgFinding the initial kinetic energy,
[tex]\large{ \boxed{ \rm{K.E. = \frac{1}{2}m {v}^{2}}}}[/tex]
⇛ KE = (1/2)mv²
⇛ KE = (1/2)(0.042)(15.6)²
⇛ KE = 5.11 J
|| ⚡By conservation of energy, the potential energy at the highest point will also be 5.11 J, since there is no kinetic energy at the highest point because the ball is not moving (we neglect energy lost due to air resistance, heat, sound, etc.) ⚡||
So, we have:
[tex] \large{ \boxed{ \rm{P.E. = mgh}}}[/tex]
⇛ h = PE/(mg)
⇛ h = 5.11 J /(0.042 × 9.8)
⇛ h = 12.41 m
✏The ball will rise upto a height of 12.41 m
━━━━━━━━━━━━━━━━━━━━
2. The nuclear model of the atom held that
a. electrons were randomly spread through "a sphere of uniform positive
electrification."
b. matter was made of tiny electrically charged particles that were smaller than the
atom
C. matter was made of tiny, indivisible particles.
d. the atom had a dense, positively charged nucleus.
Answer:
the atom had a dense, positively charged nucleus.
Explanation:
Ernest Rutherford, based on the experiment carried out by two of his graduate students, established the authenticity of the nuclear model of the atom.
According to the nuclear model, an atom is made up of a dense positive core called the nucleus. Electrons are found to move round this nucleus in orbits. This is akin to the movement of the planets round the sun in the solar system.
If the rods with diameters and lengths listed below are made of the same material, which will undergo the largest percentage length change given the same applied force along its length?a. d, 3L b. 3d, L c. 2d, 2L d. 4d, L
Answer:
The highest percentage of change corresponds to the thinnest rod, the correct answer is a
Explanation:
For this exercise we are asked to change the length of the bar by the action of a force applied along its length, in this case we focus on the expression of longitudinal elasticity
F / A = Y ΔL/L
where F / A is the force per unit length, ΔL / L is the fraction of the change in length, and Y is Young's modulus.
In this case the bars are made of the same material by which Young's modulus is the same for all
ΔL / L = (F / A) / Y
the area of the bar is the area of a circle
A = π r² = π d² / 4
A = π / 4 d²
we substitute
ΔL / L = (F / Y) 4 /πd²
changing length
ΔL = (F / Y 4 /π) L / d²
The amount between paracentesis are all constant in this exercise, let's look for the longitudinal change
a) values given d and 3L
ΔL = cte 3L / d²
ΔL = cte L /d² 3
To find the percentage, we must divide the change in magnitude by its value and multiply by 100.
ΔL/L % = [(F /Y 4/π 1/d²) 3L ] / 3L 100
ΔL/L % = cte 100%
b) 3d and L value, we repeat the same process as in part a
ΔL = cte L / 9d²
ΔL = cte L / d² 1/9
ΔL / L% = cte 100/9
ΔL / L% = cte 11%
c) 2d and 2L value
ΔL = (cte L / d ½ )/ 2L
ΔL/L% = cte 100/4
ΔL/L% = cte 25%
d) value 4d and L
ΔL = cte L / d² 1/16
ΔL/L % = cte 100/16
ΔL/L % = cte 6.25%
The highest percentage of change corresponds to the thinnest rod, the correct answer is a
1. What does the acronym LASER stand for? What characteristic of a laser makes it suitable for today's experiment?
Answer:Light Amplification by Stimulated Emission of Radiation. It is able to convert light or electrical energy into focused high energy beam to treat some sickness and diseases.
Explanation:
Answer:
Light amplification by stimulated emission of radiation
A professor, with dumbbells in his hands and holding his arms out, is spinning on a turntable with an angular velocity. What happens after he pulls his arms inwards
Answer:
His angular velocity will increase.
Explanation:
According to the conservation of rotational momentum, the initial angular momentum of a system must be equal to the final angular momentum of the system.
The angular momentum of a system = [tex]I[/tex]'ω'
where
[tex]I[/tex]' is the initial rotational inertia
ω' is the initial angular velocity
the rotational inertia = [tex]mr'^{2}[/tex]
where m is the mass of the system
and r' is the initial radius of rotation
Note that the professor does not change his position about the axis of rotation, so we are working relative to the dumbbells.
we can see that with the mass of the dumbbells remaining constant, if we reduce the radius of rotation of the dumbbells to r, the rotational inertia will reduce to [tex]I[/tex].
From
[tex]I[/tex]'ω' = [tex]I[/tex]ω
since [tex]I[/tex] is now reduced, ω will be greater than ω'
therefore, the angular velocity increases.
The ancient Greek Eratosthenes found that the Sun casts different lengths of shadow at different points on Earth. There were no shadows at midday in Aswan as the Sun was directly overhead. 800 kilometers north, in Alexandria, shadow lengths were found to show the Sun at 7.2 degrees from overhead at midday. Use these measurements to calculate the radius of Earth.
Answer:
The radius of the earth is [tex]r = 6365.4 \ km[/tex]
Explanation:
From the question we are told that
The distance at Alexandria is [tex]d_a = 800 \ km = 800 *10^{3} \ m[/tex]
The angle of the sun is [tex]\theta = 7.2 ^o[/tex]
So we want to first obtain the circumference of the earth
So let assume that the earth is circular ([tex]360 ^o[/tex])
Now from question we know that the sun made an angle of [tex]7.2 ^o[/tex] so with this we will obtain how many [tex](7.2 ^o)[/tex] are in [tex]360^o[/tex]
i.e [tex]N = \frac{360}{7.2}[/tex]
=> [tex]N = 50[/tex]
With this value we can evaluate the circumference as
[tex]c = 50 * 800[/tex]
[tex]c = 40000 \ km[/tex]
Generally circumference is mathematically represented as
[tex]c = 2\pi r[/tex]
[tex]40000 = 2 * 3.142 * r[/tex]
=> [tex]r = 6365.4 \ km[/tex]
light bulb is connected to a 110-V source. What is the resistance of this bulb if it is a 100-W bulb
Answer:
121ohmsExplanation:
Formula used for calculating power P = current * voltage
P = IV
From ohms law, V = IR where R is the resistance. Substituting V = IR into the formula for calculating power, we will have;
P = IV
P =(V/R)V
P = V²/R
Given parameters
Power rating of the bulb P = 100 Watts
Source voltage V = 110V
Required
Resistance of the bulb R
Substituting the given parameters into the formula for calculating power to get Resistance R;
P = V²/R
100 = 110²/R
R = 110²/100
R = 110 * 110/100
R = 12100/100
R = 121 ohms
Hence, the resistance of this bulb is 121 ohms
Astronomers think planets formed from interstellar dust and gases that clumped together in a process called? A. stellar evolution B. nebular aggregation C. planetary accretion D. nuclear fusion
Answer:
C. planetary accretion
Explanation:
Astronomers think planets formed from interstellar dust gases that clumped together in a process called planetary accretion.
Answer:
[tex]\boxed{\sf C. \ planetary \ accretion }[/tex]
Explanation:
Astronomers think planets formed from interstellar dust and gases that clumped together in a process called planetary accretion.
Planetary accretion is a process in which huge masses of solid rock or metal clump together to produce planets.
A 2.0 m × 4.0 m flat carpet acquires a uniformly distributed charge of −10 μC after you and your friends walk across it several times. A 5.0 μg dust particle is suspended in midair just above the center of the carpet.
Required:
What is the charge on the dust particle?
Answer:
The charge on the dust particle is [tex]q_d = 6.94 *10^{-13} \ C[/tex]
Explanation:
From the question we are told that
The length is [tex]l = 2.0 \ m[/tex]
The width is [tex]w = 4.0 \ m[/tex]
The charge is [tex]q = -10\mu C= -10*10^{-6} \ C[/tex]
The mass suspended in mid-air is [tex]m_a = 5.0 \mu g = 5.0 *10^{-6} \ g = 5.0 *10^{-9} \ kg[/tex]
Generally the electric field on the carpet is mathematically represented as
[tex]E = \frac{q}{ 2 * A * \epsilon _o}[/tex]
Where [tex]\epsilon _o[/tex] is the permittivity of free space with value [tex]\epsilon_o = 8.85*10^{-12} \ \ m^{-3} \cdot kg^{-1}\cdot s^4 \cdot A^2[/tex]
substituting values
[tex]E = \frac{-10*10^{-6}}{ 2 * (2 * 4 ) * 8.85*10^{-12}}[/tex]
[tex]E = -70621.5 \ N/C[/tex]
Generally the electric force keeping the dust particle on the air equal to the force of gravity acting on the particles
[tex]F__{E}} = F__{G}}[/tex]
=> [tex]q_d * E = m * g[/tex]
=> [tex]q_d = \frac{m * g}{E}[/tex]
=> [tex]q_d = \frac{5.0 *10^{-9} * 9.8}{70621.5}[/tex]
=> [tex]q_d = 6.94 *10^{-13} \ C[/tex]
A 58 g firecracker is at rest at the origin when it explodes into three pieces. The first, with mass 12 g , moves along the x axis at 37 m/s in the positive direction. The second, with mass 22 g , moves along the y axis at 34 m/s in the positive direction. Find the velocity of third piece.
Answer:
Explanation:
We shall apply conservation of momentum law in vector form to solve the problem .
Initial momentum = 0
momentum of 12 g piece
= .012 x 37 i since it moves along x axis .
= .444 i
momentum of 22 g
= .022 x 34 j
= .748 j
Let momentum of third piece = p
total momentum
= p + .444 i + .748 j
so
applying conservation law of momentum
p + .444 i + .748 j = 0
p = - .444 i - .748 j
magnitude of p
= √ ( .444² + .748² )
= .87 kg m /s
mass of third piece = 58 - ( 12 + 22 )
= 24 g = .024 kg
if v be its velocity
.024 v = .87
v = 36.25 m / s .
Which of these cannot be a resistor in a series or parallel circuit?
A)switch
B) battery
C) light bulb
D) all of these are resistors
Answer:
it is going to D. all of these are resistors
A resistance heater having 20.7 kW power is used to heat a room having 16 m X 16.5 m X 12.3 m size from 13.5 to 21 oC at sea level. The room is sealed once the heater is turned on. Calculate the amount of time needed for this heating to occur in min. (Write your answer in 3 significant digits. Assume constant specific heats at room temperature.)
Answer:
t = 23.6 min
Explanation:
First we need to find the mass of air in the room:
m = ρV
where,
m = mass of air in the room = ?
ρ = density of air at room temperature = 1.2041 kg/m³
V = Volume of room = 16 m x 16.5 m x 12.3 m = 3247.2 m³
Therefore,
m = (1.2041 kg/m³)(3247.2 m³)
m = 3909.95 kg
Now, we find the amount of energy consumed to heat the room:
E = m C ΔT
where,
E = Energy consumed = ?
C = Specific Heat of air at room temperature = 1 KJ/kg.⁰C
ΔT = Change in temperature = 21 °C - 13.5 °C = 7.5 °C
Therefore,
E = (3909.95 kg)(1 KJ/kg.°C)(7.5 °C)
E = 29324.62 KJ
Now, the time period can be calculated as:
P = E/t
t = E/P
where,
t = Time needed = ?
P = Power of heater = 20.7 KW
Therefore,
t = 29324.62 KJ/20.7 KW
t = (1416.65 s)(1 min/60 s)
t = 23.6 min
An electric device delivers a current of 5.0 A to a circuit. How many electrons flow through this circuit in 5 s?
Answer:
1.6×10²⁰
Explanation:
An ampere is a Coulomb per second.
1 A = 1 C / s
The amount of charge after 5 seconds is:
5.0 A × 5 s = 25 C
The number of electrons is:
25 C × (1 electron / 1.6×10⁻¹⁹ C) = 1.6×10²⁰ electrons
front wheel drive car starts from rest and accelerates to the right. Knowing that the tires do not slip on the road, what is the direction of the friction force the road applies to the rear tire
Answer:
The frictional force the road applies to the rear tire is static friction and it acts opposite to the direction in which the car is traveling.
Explanation:
This question suggests that the car is accelerating forward. Thus, the easiest way for us to know what friction is doing is for us to know what happens when we turn friction off.
Now, if there is no friction and the car is stopped, if we push down on the accelerator, it will make the front wheels to spin in a clockwise manner. This spin occurs on the frictionless surface with the rear wheels doing nothing while the car doesn't move.
Now, if we apply friction to just the front wheels, the car will accelerate forward while the back wheels would be dragging along the road and not be spinning. Thus, friction opposes the motion and as such, it must act im a direction opposite to where the car is going. This must be static friction.
The frictional force the road applies to the rear tire is static friction and it acts opposite to the direction in which the car is traveling.
Determine the next possible thickness of the film (in nm) that will provide the proper destructive interference. The index of refraction of the glass is 1.58 and the index of refraction of the film material is 1.48.
Answer:
I know the answer
Explanation:
We want to choose the film thickness such that destructive interference occurs between the light reflected from the air-film interface (call it wave 1) and from the film-lens interface (call it wave 2). For destructive interference to occur, the phase difference between the two waves must be an odd multiple of half-wavelengths.
You can think of the phases of the two waves as second hands on a clock; as the light travels, the hands tick-tock around the clock. Consider the clocks on the two waves in question. As both waves travel to the air-film interface, their clocks both tick-tock the same time-no phase difference. When wave 1 is reflected from the air-film boundary, its clock is set forward 30 seconds; i.e., if the hand was pointing toward 12, it's now pointing toward 6. It's set forward because the index of refraction of air is smaller than that of the film.
Now wave 1 pauses while wave two goes into and out of the film. The clock on wave 2 continues to tick as it travels in the film-tick, tock, tick, tock.... Clock 2 is set forward 30 seconds when it hits the film-lens interface because the index of refraction of the film is smaller than that of the lens. Then as it travels back through the film, its clock still continues ticking. When wave 2 gets back to the air-film interface, the two waves continue side by side, both their clocks ticking; there is no change in phase as they continue on their merry way.
So, to recap, since both clocks were shifted forward at the two different interfaces, there was no net phase shift due to reflection. There was also no phase shift as the waves travelled into and out from the air-film interface. The only phase shift occured as clock 2 ticked inside the film.
Call the thickness of the film t. Then the total distance travelled by wave 2 inside the film is 2t, if we assume the light entered pretty much normal to the interface. This total distance should equal to half the wavelength of the light in the film (for the minimum condition; it could also be 3/2, 5/2, etc., but that wouldn't be the minimum thickness) since the hand of the clock makes one revolution for each distance of one wavelength the wave travels (right?).
