A frictionless spring with a 9-kg mass can be held stretched 1.8 meters beyond its natural length by a force of 80 newtons. If the spring begins at its equilibrium position, but a push gives it an initial velocity of 1.5 m/sec, find the position of the mass after tt seconds. meters

Answer:The radioactive waste

Explanation:Fission is the splitting of a heavy unstable nucleus into two Lighter nuclei

Answer:

the change in the kinetic energy of the system is -42.47 J

Explanation:

Given;

mass A, Ma = 2 kg

initial velocity of mass A, Ua = 15 m/s

Mass M, Mm = 4 kg

initial velocity of mass M, Um = 7 m/s

Let the common velocity of the two masses after collision = V

Apply the principle of conservation of linear momentum, to determine the final velocity of the two masses;

[tex]M_aU_a + M_mU_m = V(M_a + M_m)\\\\(2\times 15 )+ (4\times 7) = V(2+4)\\\\58 = 6V\\\\V = \frac{58}{6} = 9.67 \ m/s[/tex]

The initial kinetic of the two masses;

[tex]K.E_i = \frac{1}{2} M_aU_a^2 \ + \ \frac{1}{2} M_mU_m^2\\\\K.E_i = (0.5 \times 2\times 15^2) \ + \ (0.5 \times 4\times 7^2)\\\\K.E_i = 323 \ J[/tex]

The final kinetic energy of the two masses;

[tex]K.E_f = \frac{1}{2} M_aV^2 \ + \ \frac{1}{2} M_mV^2\\\\K.E_f = \frac{1}{2} V^2(M_a + M_m)\\\\K.E_f = \frac{1}{2} \times 9.67^2(2+ 4)\\\\K.E_f = 280.53 \ J[/tex]

The change in kinetic energy is calculated as;

[tex]\Delta K.E = K.E_f \ - \ K.E_i\\\\\Delta K.E = 280.53 \ J \ - \ 323 \ J\\\\\Delta K.E = -42.47 \ J[/tex]

Therefore, the change in the kinetic energy of the system is -42.47 J

Answer:

Types of tidal turbines

Axial turbines.

Crossflow turbines.

Flow augmented turbines.

Oscillating devices.

Venturi effect.

Tidal kite turbines.

Turbine power.

Resource assessment.

Answer:

Axial turbines

Crossflow turbines

flow augmented turbines

Answer:

1.84 hours

I hope it's helps you

Answer:

5 m/s I hope it will help you

Explanation:

mark me as a brainlist answer

Answer:

a)   R₁ = 14.1 Ω,   b)  R₂ =  19.9 Ω

Explanation:

For this exercise we must use ohm's law remembering that in a series circuit the equivalent resistance is the sum of the resistances

all resistors connected

           V = i (R₁ + R₂)

with R₁ connected

           V = (i + 0.5) R₁

with R₂ connected

           V = (i + 0.25) R₂

We have a system of three equations with three unknowns for which we can solve it

We substitute the last two equations in the first

           V = i ( [tex]\frac{V}{ i+0.5} + \frac{V}{i+0.25}[/tex] )

           1 = i ( [tex]\frac{1}{i+0.5} + \frac{1}{i+0.25}[/tex] )

           1 = i ( [tex]\frac{i+0.5+i+0.25}{(i+0.5) \ ( i+0.25) }[/tex] ) =  [tex]\frac{i^2 + 0.75i}{i^2 + 0.75 i + 0.125}[/tex]

           i² + 0.75 i + 0.125 = 2i² + 0.75 i

           i² - 0.125 = 0

           i = √0.125

           i = 0.35355 A

with the second equation we look for R1

          R₁ = [tex]\frac{V}{i+0.5}[/tex]

          R₁ = 12 /( 0.35355 +0.5)

          R₁ = 14.1 Ω

with the third equation we look for R2

          R₂ = [tex]\frac{V}{i+0.25}[/tex]

          R₂ =[tex]\frac{12}{0.35355+0.25}[/tex]

          R₂ =  19.9 Ω

Answer:

233.33°F

Explanation:

(385K - 273.15) * 9/5 + 32 = 233.33°F

Answer:

The pressure of water progressively increases as the depth of the water increases. The pressure increases as the depth of a point in a liquid increases. The walls of the vessel in which liquids are held are likewise subjected to pressure. The sideways pressure exerted by liquids increases as the liquid depth increases.

Answer:

About 37.70 radians.

Explanation:

1 revolution = 2[tex]\pi[/tex] radians

∴ 6 revolutions = (6)(2[tex]\pi[/tex] radians)

6 revolutions = 37.6991 or ≈ 37.70 radians

Explanation:

Those tools that helps to make our work easier ,faster and more convenient in our daily life it is called simple Machine.

Answer:

the initial velocity of the car is 12.04 m/s

Explanation:

Given;

force applied by the break, f = 1,398 N

distance moved by the car before stopping, d = 25 m

weight of the car, W = 4,729 N

The mass of the car is calculated as;

W = mg

m = W/g

m = (4,729) / (9.81)

m = 482.06 kg

The deceleration of the car when the force was applied;

-F = ma

a = -F/m

a = -1,398 / 482.06

a = -2.9 m/s²

The initial velocity of the car is calculated as;

v² = u² + 2ad

where;

v is the final velocity of the car at the point it stops = 0

u is the initial velocity of the car before the break was applied

0 = u² + 2(-a)d

0 = u² - 2ad

u² = 2ad

u = √2ad

u = √(2 x 2.9 x 25)

u =√(145)

u = 12.04 m/s

Therefore, the initial velocity of the car is 12.04 m/s

Answer:

Explanation:

The law of reflection says that the reflected angle (measured from a vertical line to the surface  called the normal) is equal to the reflected angle measured from the same normal line.

All other properties of reflection flow from this one statement.

Answer:

[tex]F=133N[/tex]

Explanation:

From the question we are told that:

Length [tex]l=3.0m[/tex]

Mass [tex]m=24kg[/tex]

Distance from Tip [tex]d=35cm[/tex]

Generally, the equation for Torque Balance is mathematically given by

[tex]mg(l/2)=F(l-d)[/tex]

[tex]2*9.81(3/2)=F(3-35*10^-2)[/tex]

Therefore

[tex]F=133N[/tex]

i'm pretty sure the answer is A wider

Electric lines of force where intensity of electric field is maximum when its wider.

The physical field that surrounds electrically charged particles and exerts force on all other charged particles in the field, either attracting or repelling them, is known as an electric field (also known as an E-field. It can also refer to a system of charged particles' physical field.

Electric charges and time-varying electric currents are the building blocks of electric fields. The electromagnetic field, one of the four fundamental interactions (also known as forces) of nature, manifests itself in both electric and magnetic fields.

Electrical technology makes use of electric fields, which are significant in many branches of physics. For instance, in atomic physics and chemistry, the electric field acts as an attracting force to hold atoms' atomic nuclei and electrons together.

Therefore, Electric lines of force where intensity of electric field is maximum when its wider.

To learn more about electric field, refer to the link:

https://brainly.com/question/1443103

#SPJ2

Answer:

Explanation:

Given force between 2 currents carrying

wires = F₀

Magnetic force between the2 wires =F₀= (μ₀/4π) x ( 2 (μ₀/4π) x ( 2I₁I₂ / μ) x L

where I₁=Current in wire 1

           I₂= Current in wire 2

           L= Length of the wire

when one current is doubled and the other is halved

I₁= 2 I₁

I₂=    I₂/2

F₀ = (μ₀/4π) x ( 2× (2I₁) (I₂/2) / μ) x L

Answer:

(A) Gravity is you're answer.

Explanation:

When an object or human is falling at an increased rate, The force of gravity is taking place.

Answer:

approaches infinity

Explanation:

There are two momentums, the classical momentum which is equal to the product of mass and velocity, and the relativistic momentum, the one we should look at when we work with high speeds, and this happens because massive objects have a speed limit, in this case, we are approaching the speed of light, so we need to work with the relativistic momentum instead of the classical momentum.

The relativistic momentum can be written as:

[tex]p = \frac{1}{\sqrt{1 - \frac{u^2}{c^2} } } *m*u[/tex]

where

u = speed of the object relative to the observer, in this case we have that u tends to c, the speed of light.

m = mass of the object

c = speed of light.

So, as u tends to c, we will have:

[tex]\lim_{u \to c} p = \frac{1}{\sqrt{1 - \frac{u^2}{c^2} } } *m*u[/tex]

Notice that when u tends to c, the denominator on the first term tends to zero, thus, the relativistic momentum of the object will tend to infinity.

Then the correct option is infinity, as the particle speed approaches the speed of light, the relativistic momentum of the particle tends to infinity.

Answer:

wegkwe fhkrbhefdb

Explanation:B

Answer:

The smallest and largest areas could be 6400 m and 7500 m, respectively.

Explanation:

The area of a rectangle is given by:

[tex] A = l*w [/tex]

Where:

l: is the length = 100 m

w: is the width

We can calculate the smallest area with the lower value of the width.

[tex] A_{s} = 100 m*64 m = 6400 m^{2} [/tex]                            

And the largest area is:

[tex] A_{l} = 100 m*75 m = 7500 m^{2} [/tex]  

Therefore, the smallest and largest areas could be 6400 m and 7500 m, respectively.            

I hope it helps you!                        

Answer:

the largest areas that the field could be is [tex]A_l[/tex]=7587.75 m

the smallest areas that the field could be is [tex]A_s[/tex]=6318.25 m

Explanation:

to the find the largest and the smallest area of the field measurement error is to be considered.

we have to find the greatest possible error, since the measurement was made nearest whole mile, the greatest possible error is half of 1 mile and that is 0.5m.

therefore to find the largest possible area we add the error in the mix of the formular for finding the perimeter with the largest width as shown below:

[tex]A_l[/tex]= (L+0.5)(W+0.5)

(100+0.5)(75+0.5) = (100.5)(75.5) = 7587.75 m

To find the smallest length we will have to subtract instead of adding the error factor value of 0.5 as shown below:

[tex]A_s[/tex]= (L-0.5)(W-0.5)

(100-0.5)(64-0.5) = (99.5)(63.5) = 6318.25 m

Answer:

D) 1003 N​

Explanation:

Given the following data;

Mass of man = 85 kg

Acceleration of elevator = 2 m/s²

Acceleration due to gravity, g = 9.8 m/s²

To find the force exerted by the man on the floor;

Force = mg + ma

Answer:

9 Brainly hahaha ............huh

One of the two requirements of electric current is there must be an electric potential between two bodies

For electric current to flow, there must be an electric potential between two bodies.

This is because electric charge flows from a higher electric potential to a lower electric potential just as, water flows from a higher gravitational potential to a lower gravitational potential.

The difference between the electric potential between the two bodies causes the electric charge to flow between the two bodies.

This flow of electric charge constitutes electric current and electric current will only flow when there is an electric potential between two bodies.

So, one of the two requirements of electric current is there must be an electric potential between two bodies.

So, the answer is A

Learn more about electric current here:

https://brainly.com/question/13562393

(a) The maximum height reached by the ball from the ground level is 75.87m

(b) The time taken for the ball to return to the elevator floor is 2.21 s

The given parameters include:

To calculate:

(a) the maximum height of the projectile

total initial velocity of the projectile = 10 m/s + 20 m/s  = 30 m/s (since the elevator is ascending at a constant speed)

at maximum height the final velocity of the projectile (ball), v = 0

Apply the following kinematic equation to determine the maximum height of the projectile.

[tex]v^2 = u^2 + 2(-g)h_3\\\\where;\\\\g \ is \ the \ acceleration \ due \ to\ gravity = 9.81 \ m/s^2\\\\h_3 \ is \ maximum \ height \ reached \ by \ the \ ball \ from \ the \ point \ of \ projection\\\\0 = u^2 -2gh_3\\\\2gh_3 = u^2 \\\\h_3 = \frac{u^2}{2g} \\\\h_3 = \frac{(30)^2}{2\times 9.81} \\\\h_3 = 45.87 \ m[/tex]

The maximum height reached by the ball from the ground level (h) = height of the elevator from the ground level + height of he boy above the elevator + maximum height reached by elevator from the point of projection

h = h₁ + h₂ + h₃

h = 28 m + 2 m  +  45.87 m

h = 75.87 m

(b) The time taken for the ball to return to the elevator floor

Final height of the ball above the elevator floor = 2 m + 45.87 m = 47.87 m

Apply the following kinematic equation to determine the time to return to the elevator floor.

[tex]h = vt + \frac{1}{2} gt^2\\\\where;\\\\v \ is \ the \ initial \ velocity \ of \ the \ ball \ at \ the \ maximum \ height = 0\\\\h = \frac{1}{2} gt^2\\\\gt^2 = 2h\\\\t^2 = \frac{2h}{g} \\\\t = \sqrt{\frac{2h}{g}} \\\\t = \sqrt{\frac{2\times 47.87}{9.81}} \\\\t = 2.21 \ s[/tex]

To learn more about projectile calculations please visit: https://brainly.com/question/14083704

This question is incomplete, the complete question is;

A solenoid has a length 11.34 cm , a radius 1.85 cm , and 1627 turns. The solenoid has a net resistance of 144.9 Ω . A circular loop with radius of 3.77 cm is placed around the solenoid, such that it lies in a plane whose normal is aligned with the solenoid axis, and the center of the outer loop lies on the solenoid axis. The outer loop has a resistance of 1651.6 Ω. At a time of 0 s , the solenoid is connected to a battery that supplies a potential 34.95 V. At a time 2.58 μs , what current flows through the outer loop?

Answer:

the current flows through the outer loop is 1.3 × 10⁻⁵ A

Explanation:

Given the data in the question;

Length [tex]l[/tex] = 11.34 cm = 0.1134 m

radius a = 1.85 cm = 0.0185 m

turns N = 1627

Net resistance [tex]R_{sol[/tex] = 144.9 Ω

radius b = 3.77 cm = 0.0377 m

[tex]R_o[/tex] = 1651.6 Ω

ε = 34.95 V

t = 2.58 μs = 2.58 × 10⁻⁶ s

Now, Inductance; L = μ₀N²πa² / [tex]l[/tex]

so

L = [ ( 4π × 10⁻⁷ ) × ( 1627 )² × π( 0.0185 )² ] / 0.1134

L = 0.003576665 / 0.1134

L = 0.03154

Now,

ε = d∅/dt = [tex]\frac{d}{dt}[/tex]( BA ) =  [tex]\frac{d}{dt}[/tex][ (μ₀In)πa² ]

so

ε = μ₀n [tex]\frac{dI}{dt}[/tex]( πa² )

ε = [ μ₀Nπa² / [tex]l[/tex] ] [tex]\frac{dI}{dt}[/tex]

ε = [ μ₀Nπa² / [tex]l[/tex] ] [ (ε/L)e^( -t/[tex]R_{sol[/tex]) ]

I = ε/[tex]R_o[/tex] = [ μ₀Nπa² / [tex]R_o[/tex][tex]l[/tex] ] [ (ε/L)e^( -t/[tex]R_{sol[/tex]) ]

so we substitute in our values;

I = [ (( 4π × 10⁻⁷ ) × 1627 × π(0.0185)²) / (1651.6 ×0.1134) ] [ ( 34.95 / 0.03154)e^( -2.58 × 10⁻⁶ / 144.9 ) ]

I = [ 2.198319 × 10⁻⁶ / 187.29144 ] [ 1108.116677 × e^( -1.7805 × 10⁻⁸ )

I = [ 1.17374 × 10⁻⁸ ] × [ 1108.116677 × 0.99999998 ]

I = [ 1.17374 × 10⁻⁸ ] × [ 1108.11665 ]

I = 1.3 × 10⁻⁵ A

Therefore, the current flows through the outer loop is 1.3 × 10⁻⁵ A

Answer:

1.28 *10^-5 A

Explanation:

Same work as above answer. Needs to be more precise

Answer:

960 nm

Explanation:

Given that:

wavelength = 640 nm

For the second (2nd) dark spot;  the order of interference m = 1

Thus, the path length difference is expressed by the formula:

[tex]d sin \theta = (m + \dfrac{1}{2}) \lambda[/tex]

[tex]d sin \theta = (1 + \dfrac{1}{2}) 640[/tex]

[tex]d sin \theta = ( \dfrac{3}{2}) 640[/tex]

dsinθ = 960 nm

Answer:

W = 641.52 J

Explanation:

The work done here will be the sum of potential energy and the kinetic energy of the boy. Here potential energy accounts for vertical motion part while the kinetic energy accounts for the horizontal motion part:

[tex]Work\ Done = Kinetic\ Energy + Potential\ Energy\\\\W = K.E +P.E\\\\W = \frac{1}{2}mv^2+mgh\\\\[/tex]

where,

W = Work Done = ?

m = mass = 6 kg

v = speed = 4.2 m/s

g = acceleration dueto gravity = 9.81 m/s²

h = height = 10 m

Therefore,

[tex]W = \frac{1}{2}(6\ kg)(4.2\ m/s)^2+(6\ kg)(9.81\ m/s^2)(10\ m)[/tex]

W = 52.92 J + 588.6 J

W = 641.52 J

Answer:

simultaneously

Time taken to reach the ground depends on the vertical component of velocity, not horizontal component of velocity.

La energía que almacena el resorte cuando se comprime y estira 12 cm es 9,4 J.  

La energía potencial elástica del resorte se puede calcular con la siguiente ecuación:

[tex] E_{p} = \frac{1}{2}kx^{2} [/tex]

En donde:

k: es la constante del resorte = 1300 N/m

x: es la distancia de compresión o de elongación = 12 cm = 0,12 m

Dado que la energía es proporcional al cuadrado de la distancia recorrida por el resorte (x), la energía almacenada por el resorte durante la compresión será la misma que la energía almacenada por la elongación.

Por lo tanto, la energía almacenada es:

[tex]E_{p} = \frac{1}{2}kx^{2} = \frac{1}{2}1300 N/m*(0,12 m)^{2} = 9,4 J[/tex]                                                            

Entonces, la energía del resorte cuando se comprime y cuando se estira es la misma, a saber 9,4 J.                

Para saber más sobre energía potencial visita este link: https://brainly.com/question/156316?referrer=searchResults

Espero que te sea de utilidad!

Answer:

Al comprimirse o estirarse 12 centímetros desde su posición sin deformar, el resorte almacena 9,360 joules.

Explanation:

La Energía Potencial Elástica almacenada por el resorte ([tex]U_{e}[/tex]), en joules, se calcula a partir de la Ley de Hooke, la definición de Trabajo y el Teorema del Trabajo y la Energía, cuya expresión se presenta abajo:

[tex]U_{e} = \frac{1}{2}\cdot k\cdot (x_{f}^{2}-x_{o}^{2})[/tex] (1)

Donde:

[tex]k[/tex] - Constante elástica del resorte, en newtons por metro.

[tex]x_{o}[/tex] - Posición inicial del resorte, en metros.

[tex]x_{f}[/tex] - Posición final del resorte, en metros.

Nótese que el resorte sin deformar tiene una posición de cero, la tensión tiene un valor positivo y la compresión, negativo.

Asumiendo que en ambos casos el resorte se encuentra inicialmente sin deformar, se reduce (1) a una forma de función par, es decir, una función que cumple con la propiedad de que [tex]f(x) = f(-x)[/tex], se encuentra que al comprimirse o estirarse en la misma medida almacena la misma cantidad de energía.

La cantidad de energía a almacenar es:

[tex]U_{e} = \frac{1}{2}\cdot \left(1300\,\frac{N}{m} \right)\cdot (0,12\,m)^{2}[/tex]

[tex]U_{e} = 9,360\,J[/tex]

Al comprimirse o estirarse 12 centímetros desde su posición sin deformar, el resorte almacena 9,360 joules.

Explanation:

Energy utilization focuses on technologies that can lead to new and potentially more efficient ways of using electricity in residential, commercial and industrial settings—as well as in the transportation sector

Answer:

"the ratio of increase in the volume of a solid per degree rise of temperature to its initial volume" -web

Explanation:

tbh up above ✅

Answer:

cubic meter

Explanation:

Increase in volume of a body on heating is referred to as volumetric expansion or cubical expansion