Answer:
The partial pressure will be "100 torr".
Explanation:
Given:
[tex]P_{Ar} = 300 \ torr[/tex]
By assuming Ar and Ne having 50 gm each, we get
mol of Ne = [tex]\frac{50}{20}[/tex]
= [tex]2.5 \ mol[/tex]
mol of Ar = [tex]\frac{50}{40}[/tex]
= [tex]1.25 \ mol[/tex]
now,
[tex]n_T= mol.A_r+mol.N_e[/tex]
[tex]=1.25+2.5[/tex]
[tex]=3.75[/tex]
then,
[tex]X_{Ar}=\frac{n_{Ar}}{n_T}[/tex]
[tex]=\frac{1.25}{3.75}[/tex]
[tex]=0.33[/tex]
hence,
The partial pressure of Ar will be:
⇒ [tex]P_{Ar} = P_T\times X_{AT}[/tex]
By substituting the values, we get
[tex]=300\times 0.33[/tex]
[tex]=100 \ torr[/tex]
The partial pressure of Ar in the mixture is 99.9 torr
Let the mass of both gas be 10 g
Next, we shall determine mole of each gas.
For Ne:Mass = 10 g
Molar mass of Ne = 20 g/mol
Mole of Ne =?Mole = mass / molar mass
Mole of Ne = 10 / 20
Mole of Ne = 0.5 mole For Ar:Mass = 10 g
Molar mass of Ar = 40 g/mol
Mole of Ar =?Mole = mass / molar mass
Mole of Ar = 10 / 40
Mole of Ar = 0.25 moleNext, we shall determine the mole fraction of Ar
Mole of Ne = 0.5 mole
Mole of Ar = 0.25 mole
Total mole = 0.5 + 0.25 = 0.75 mole
Mole fraction of Ar =?[tex]mole \: fraction \: = \frac{mole}{total \: mole} \\ \\ mole \: fraction \: of \:Ar = \frac{0.25}{0.75} \\ \\ mole \: fraction \: of \:Ar = 0.333 \\ \\ [/tex]
Finally, we shall determine the partial pressure of Ar
Mole fraction of Ar = 0.333
Total pressure = 300 torr
Partial pressure of Ar =?Partial pressure = mole fraction × total pressure
Partial pressure of Ar = 0.333 × 300
Partial pressure of Ar = 99.9 torrLearn more on partial pressure: https://brainly.com/question/15577259
1. What is uncertainty in measurements?
Answer:
In metrology, measurement uncertainty is the expression of the statistical dispersion of the values attributed to a measured quantity.By international agreement, this uncertainty has a probabilistic basis and reflects incomplete knowledge of the quantity value. It is a non-negative parameter.
Hope it helps you.Four atoms and/or ions are sketched below in accordance with their relative atomic and/or ionic radii. Which of the following sets of species are compatible with the sketch?
Explain. (a) C,Ca2+,Cl−,Br−;
(b) Sr4, Cl,Br−,Na+
(d) Al,Ra2+,Zr2+
(c) Y,K,Ca,Na+, Mg2+;
e) Fe,Rb,Co,Cs
Answer:
Hence the correct option is an option (b) Sr4, Cl,Br−,Na+.
Explanation:
Bromine and chlorine belong to an equivalent group. As we go down the group the dimensions increases which too there's a charge on the bromine atom. therefore the size of the Br- is going to be larger in comparison to the chlorine atom.
Sr atom is within the second group, and also it's below the above-mentioned atoms.so Sr is going to be the larger one among all the atoms.
Sodium and chlorine belong to an equivalent period .size decrease from left to right. but due to the charge on sodium its size decreases and there's an opportunity that Na+ size could be adequate for Cl.
Here we finally assume that two atoms are of an equivalent size (Na+ and Cl) which are less in size compared to the opposite two(Sr and Br-) during which one is greater (Sr)and the opposite is smaller(Br-).
Convert the concentration of 0.700 M Na2SO4 to g/mol
To convert from mass concentration to molar concentration we use the formula;
Mass concentration = molar concentration * molar mass
Molar concentration of Na2SO4 = 0.700 M
Molar mass of Na2SO4 = 2(23) + 32 + 4(16) = 142 gmol-1
Hence;
Mass concentration = 0.700 M * 142 gmol-1
Mass concentration = 99.4 g/mol
To know more about concentration, see
https://brainly.com/question/23437000
11. An isotope Q has 18 neutrons a mass number of 34. (a) (i) What is an isotope? An isotope is one of two or C (b) Write its electron arrangement. Mass number=34 Number of neutrons=18 Number of Protons = 34-15-16 (c) To which period and group does Q belong? Protors - Electons - Atomic number Period - Group (d) How does Q form its ion?
An isotope is an element with the same atomic number but different mass number due to differences in number of neutrons.
electron configuration is 2,8,6.
Belongs to group 6 and period group 3.
It forms an ion by accepting 2 electrons
3. HNO3 + NaHCO3 → NaNO3 + H2O + CO2
4. AgNO3 +CaCl2 → AgCl + Ca(NO3)2
5. 3 H2(g) + N2(g) → 2 NH3(g)
6. 2 H202 → 2 H2O + O2
Write word equation and type of reaction
Answer:
hydrogen nitrate + sodium hydrochlorate- sodium nitrate+ water + co2 (acid base reaction)
silver nitrate + calcium chloride - silver chloride+ calcium nitrate ( double displacement reaction)
hydrogen + nitrogen - ammonia gas ( simple contact reaction)
hydrogen peroxide - water + oxygen ( single displacement reaction)
Hope it helps :)
Part A
3.75 mol of LiCl in 3.36 L of solution
Express the molarity in moles per liter to three significant figures
Answer:
1.12 mol/L.
Explanation:
From the question given above, the following data were obtained:
Mole of LiCl = 3.75 moles
Volume = 3.36 L
Molarity =?
Molarity is simply defined as the mole of solute per unit litre of the solution. Mathematically, it is expressed as:
Molarity = mole / Volume
With the above formula, we can obtain the molarity of the solution as follow:
Mole of LiCl = 3.75 moles
Volume = 3.36 L
Molarity =?
Molarity = mole /Volume
Molarity = 3.75 / 3.36
Molarity = 1.12 mol/L
Thus, the molarity of the solution is 1.12 mol/L
The decomposition of ammonia is: 2 NH3(g) ⇌ N2(g) + 3 H2(g). If Kp is 1.5 × 103 at 400°C, what is the partial pressure of ammonia at equilibrium when N2 is 0.20 atm and H2 is 0.15 atm?
Answer:
"[tex]6.7\times 10^{-4} \ atm[/tex]" is the right answer.
Explanation:
Given:
Partial pressure of [tex]N_2[/tex],
= 0.20 atm
Partial pressure of [tex]H_2[/tex],
= 0.15 atm
[tex]K_p = 1.5\times 10^3[/tex] at [tex]400^{\circ} C[/tex]
As we know,
⇒ [tex]K_p = \frac{pN_2\times pH_2^3}{pNH_3^2}[/tex]
By putting the values, we get
[tex]1.5\times 10^3=\frac{0.20\times (0.15)^3}{pNH_3^2}[/tex]
[tex]pNH_3^2 = \frac{0.000675}{1.5\times 10^3}[/tex]
[tex]=6.7\times 10^{-4} \ atm[/tex]
Part A
When the following liquids are poured into the same container, they separate as shown in the image. Based on the data
in the table below, what caused the order of the layers?
rubbing alcohol
vegetable oil
water
corn syrup
Mass
Liquid
corn syrup
water
Volume Used
95 cm
90 cm
85 cm
105 cm?
130.158
90.00 8
77.358
81.908
Density
1.37 g/cm
1 g/cm
0.91 g/cm
0.78 g/cm
vegetable oil
rubbing alcohol
I
B
X
Font Sizes
A- A -
E 3
Answer: The layers are ordered by density, with the least dense layer on top, and the densest layer on the bottom.
Explanation:
Plato
FORMULAS OF IONIC COMPOUNDS
FIND: POSITIVE ION, NEGATIVE ION AND FORMULA IN:
NAME:
Sodium chloride
Magnesium chloride
Calcium oxide
Lithium phosphide
Aluminum sulfide
Calcium nitride
Iron(III)chloride
Iron(II)oxide
Copper(I)sulfide
Copper(II)nitride
Zinc oxide
Silver sulfide
Potassium carbonate
Sodium nitrate
Calcium bicarbonate
Aluminum hydroxide
Lithium phosphate
Potassium sulfate
Answer:
NaCl, Na⁺,Cl⁻.
MgCl₂, Mg²⁺, Cl⁻.
CaO, Ca²⁺, O²⁻.
Li₃P, Li⁺, P³⁻.
Al₂S₃, Al³⁺, S²⁻.
Ca₃N₂, Ca²⁺, N³⁻.
FeCl₃, Fe³⁺, Cl⁻.
FeO, Fe²⁺, O²⁻.
Cu₂S, Cu⁺, S²⁻.
Cu₃N₂, Cu²⁺, N³⁻.
ZnO, Zn²⁺, O²⁻.
Ag₂S, Ag⁺, S²⁻.
K₂CO₃, K⁺, CO₃²⁻.
NaNO₃, Na⁺, NO₃⁻.
Ca(HCO₃)₂, Ca²⁺, HCO₃⁻.
Al(OH)₃, Al³⁺,OH⁻.
Li₃PO₄, Li⁺, PO₄³⁻.
K₂SO₄, K⁺, SO₄²⁻.
Explanation:
Sodium chloride. NaCl, formed by the cation Na⁺ and the anion Cl⁻.
Magnesium chloride. MgCl₂, formed by the cation Mg²⁺ and the anion Cl⁻.
Calcium oxide. CaO, formed by the cation Ca²⁺ and the anion O²⁻.
Lithium phosphide. Li₃P, formed by the cation Li⁺ and the anion P³⁻.
Aluminum sulfide. Al₂S₃, formed by the cation Al³⁺ and the anion S²⁻.
Calcium nitride. Ca₃N₂, formed by the cation Ca²⁺ and the anion N³⁻.
Iron(III)chloride. FeCl₃, formed by the cation Fe³⁺ and the anion Cl⁻.
Iron(II)oxide. FeO, formed by the cation Fe²⁺ and the anion O²⁻.
Copper(I)sulfide. Cu₂S, formed by the cation Cu⁺ and the anion S²⁻.
Copper(II)nitride. Cu₃N₂, formed by the cation Cu²⁺ and the anion N³⁻.
Zinc oxide. ZnO, formed by the cation Zn²⁺ and the anion O²⁻.
Silver sulfide. Ag₂S, formed by the cation Ag⁺ and the anion S²⁻.
Potassium carbonate. K₂CO₃, formed by the cation K⁺ and the anion CO₃²⁻.
Sodium nitrate. NaNO₃, formed by the cation Na⁺ and the anion NO₃⁻.
Calcium bicarbonate. Ca(HCO₃)₂, formed by the cation Ca²⁺ and the anion HCO₃⁻.
Aluminum hydroxide. Al(OH)₃, formed by the cation Al³⁺ and the anion OH⁻.
Lithium phosphate. Li₃PO₄, formed by the cation Li⁺ and the anion PO₄³⁻.
Potassium sulfate. K₂SO₄, formed by the cation K⁺ and the anion SO₄²⁻.
The correct geometry around oxygen in CH3OCH3 is
(a). linear. (b). bent. C). tetrahedral/(a). trigonal planar
Explanation:
the force of the lone pairs from the bottom would cancel out the force of the lone pairs from the top. Thus, the molecule will be linear.
Where do reactions in a solid generally take place?
A. At the center of the solid.
B. All throughout the solid
C. Only on opposite sides of the solid due to repelling forces.
D. On the surface of the solid.
Answer:
It's D. On the surface of the solid.
Explanation:
If the reactant is a solid, the surface area of the solid will impact how fast the reaction goes. This is because the two types of molecule can only bump into each other at the liquid solid interface, i.e. on the surface of the solid. So the larger the surface area of the solid, the faster the reaction will be.
CaCl2 has which bond?
Answer:
CaCl2 has ionic bond because here calcium gives its electron to the chlorine atom and becomes positivetly charged ion.
which of the following measurements is equivalent to 5.461x10^-7m?
Answer:
B. 0.0000005461m
I used the method of moving the decimal.
A sample of gas occupies 10.0 L at 240°C under a pressure of
80.0 kPa. At what temperature would the gas occupy 20.0 L if
we increased the pressure to 107 kPa?
Answer: 1090°C
Explanation: According to combined gas laws
(P1 × V1) ÷ T1 = (P2 × V2) ÷ T2
where P1 = initial pressure of gas = 80.0 kPa
V1 = initial volume of gas = 10.0 L
T1 = initial temperature of gas = 240 °C = (240 + 273) K = 513 K
P2 = final pressure of gas = 107 kPa
V2 = final volume of gas = 20.0 L
T2 = final temperature of gas
Substituting the values,
(80.0 kPa × 10.0 L) ÷ (513 K) = (107 kPa × 20.0 L) ÷ T2
T2 = 513 K × (107 kPa ÷80.0 kPa) × (20.0 L ÷ 10.0 L)
T2 = 513 K × (1.3375) × (2)
T2 = 1372.275 K
T2 = (1372.275 - 273) °C
T2 = 1099 °C
1090 degree Celsius
hope it helps
An individual was injected with 80 mg of inulin and 960,000 counts per min (cpm) of tritium-labeled water (3H20) to determine the volume of various body fluid compartments. After equilibration a blood sample was obtained and the plasma inulin concentration was 0.5 mg% and the plasma activity (concentration) of tritium was 20 cpm/ml. The volumes of which body compartments can be determined?
The measurement of body fluid compartments can be achieved by the dilution of chemical compounds that only circulate and disperse in the region of selected areas in the body. The dilution process is dependent on how the concentration is defined.
Given that:
the concentration of plasma insulin after equilibrium = 0.5 mg %∴
Concentration C = 0.5 mg/100
Concentration C = 0.005 mg/ml
The mass of insulin = 80 mgSince the mass amount of the chemical compound(i.e. insulin) and the concentration is known.
The volume of the body fluid compartment can be calculated as:
[tex]\mathbf{volume = \dfrac{\text{mass of the marker }}{concentration }}[/tex]
[tex]Volume = \dfrac{80 \ mg}{0.005 \ mg/ml}[/tex]
Volume = 16000 ml
Thus, it is known that insulin is generally utilized for the measurement of the extracellular fluid volume and serves as a cell impermeant marker.
As a result;
The volume of the extracellular fluid compartment is 16000 ml.
However, the tritium-labeled water is a good marker for the entire body fluid compartment due to the fact that:
its diffusion occurs throughout the entire body,it is identical to water and;the equilibrium concentration is typically easy to measure due to the radioactive characteristics of tritium.Given that:
plasma activity of tritium = 20 cpm/ml
i.e.
In 1 ml of plasma, 20 cpm of tritium is present.
As such, in 960,000 counts per min (cpm) of tritium-labeled water, the volume of the whole body compartment is:
[tex]\mathbf{= \dfrac{960000}{20} ml \plasma}[/tex]
= 48000 ml of plasma
Therefore, we can conclude that the volumes of the body compartment that can be determined are:
The volume of the extracellular fluid compartment, which is 16000 ml.The volume of the whole body compartment, which is 48000 mlLearn more about body fluid compartments here:
https://brainly.com/question/6791522?referrer=searchResults
Given the following balanced reaction: 2Na(s) + F2(g) --> 2NaF(s)
a) How many moles of NaF will be made from 2.6 moles of F2?
b) How many moles of NaF will be made from 4.8 moles of Na?
Answer:
yes it is corrwect iyt is absolitle correct
Explanation:
In water, a substance that ionizes completely in solution is called a
Answer:
please mark me brainliest
Explanation:
In water, a substance that ionizes completely in solution is called a weak electrolyte.
Answer: strong electrolyte.
Explanation: In water, a substance that ionizes completely in solution is called a. a. weak electrolyte.
Consider the following chemical reaction:
2SO2 (g) + O2 (g) -----------> 2SO3 (g)
1.50 L. of sulfur trioxide at the pressure of 1.20 atm. and temperature of 25 oC is mixed with excess of oxygen.
Calclate volume of the product in L. at STP.
A. 11.2 L.
B. 1.65 L.
C. 16.5 L.
D. 0.129 L.
Answer:
B. 1.65 L
Explanation:
Step 1: Write the balanced equation
2 SO₂(g) + O₂(g) ⇒ 2 SO₃(g)
Step 2: Calculate the moles of SO₂
The pressure of the gas is 1.20 atm and the temperature 25 °C (298 K). We can calculate the moles using the ideal gas equation.
P × V = n × R × T
n = P × V / R × T
n = 1.20 atm × 1.50 L / (0.0821 atm.L/mol.K) × 298 K = 0.0736 mol
Step 3: Calculate the moles of SO₃ produced
0.0736 mol SO₂ × 2 mol SO₃/2 mol SO₂ = 0.0736 mol SO₃
Step 4: Calculate the volume occupied by 0.0736 moles of SO₃ at STP
At STP, 1 mole of an ideal gas occupies 22.4 L.
0.0736 mol × 22.4 L/1 mol = 1.65 L
Determine what product will be produced at the negative electrode for the following reaction:
2KCl(aq) + 2H20(1) -> H2(g) + Cl2(g) + 2KOH(aq)
A. H2
B. Cl2
с. КОН
D. K
Answer:
Choice A. [tex]\rm H_{2}[/tex] would be produced at the negative electrode.
Explanation:
Ionic equation for this reaction:
[tex]2\, {\rm K^{+}} + 2\, {\rm Cl^{-}} + {2\, \rm H_{2} O} \to {\rm H_{2}} + {\rm Cl_{2}} + 2\, {\rm K^{+}} + {\rm 2\, OH^{-}}[/tex].
Net ionic equation:
[tex]2\, {\rm Cl^{-}} + 2\, \rm H_{2} O} \to {\rm H_{2}} + {\rm Cl_{2}} + 2\, {\rm OH^{-}}[/tex].
Half-equations:
[tex]2\, {\rm Cl^{-}} \to {\rm Cl_{2}} + 2\, {e^{-}}[/tex].
(Electrons travel from the solution to an electrode.)
[tex]2\, {\rm \overset{+1}{H}_{2} O} + 2\, {e^{-}} \to \overset{0}{\rm H}_{2} + 2\, {\rm O\overset{+1}{H}\!^{-}}[/tex].
(An electrode supply electrons to the solution to reduce some of the [tex]\rm H[/tex] atoms from [tex]\rm H_{2}O[/tex].)
In a DC circuit, electrons always enter the circuit from the negative terminal of the power supply and return to the power supply at the positive terminal.
The negative electrode is connected to the negative terminal of the power supply. Electrons from the power supply would flow into the solution through this electrode.
This continuous supply of electrons at the negative electrode would drive a reduction half-reaction. In this question, that corresponds to the reduction of water: [tex]2\, {\rm \overset{+1}{H}_{2} O} + 2\, {\rm e^{-}} \to \overset{0}{\rm H}_{2} + 2\, {\rm O\overset{+1}{H}\!^{-}}[/tex]. Hence, [tex]\rm H_{2}[/tex] would be produced at the negative electrode.
What is the basic unit of chemistry?
O A. The bond
O B. The atom
O C. The sun
O D. The cell
Answer:
B. The atom
Explanation:
Cells are the most basic unit of structure and the smallest unit of matter is the atom.
Answer:
B. The atom
Explanation:
yeee it was right
During electrophilic aromatic substitution, a resonance-stabilized cation intermediate is formed. Groups, already present on the benzene ring, that direct ortho/para further stabilize this intermediate by participating in the resonance delocalization of the positive charge. Assume that the following group is present on a benzene ring at position 1 and that you are brominating the ring at positon 4. Draw the structure of the resonance contributor that shows this group actively participating in the charge delocalization.
-----OCH3
Answer:
See explanation and image attached
Explanation:
Aromatic compounds undergo electrophilic aromatic substitution reactions in which the aromatic ring is maintained.
Substituted benzenes may be more or less reactive towards electrophilic aromatic substitution than benzene depending on the nature of the substituent present in the ring.
Substituents that activate the ring towards electrophilic substitution such as -OCH3 are ortho-para directing.
The major products of the bromination of anisole are p-bromoanisole and o-bromoanisole. The resonance structures leading to these products are shown in the image attached.
The density of toluene (C7H8) is 0.867 and that of thiophene (C4H4S) is 1.065 g/ml. A solution is made by dissolving 10.00g thiophene in 250.00ml of toluene. a)Calculate the molarity of the solution
b)Assuming the volume are addictive ,calculate the molarity of the solution
Answer:
Calcular la molaridad de una solución que se preparó disolviendo 14 g de KOH en suficiente
agua para obtener 250 mL de solución. (masa molar del KOH = 56 g/mol).
Resolución: de acuerdo a la definición de “molaridad” debemos calcular primero, el número de mol de soluto (KOH) que
se han disuelto en el volumen dado, es decir, “se transforma g de soluto a mol de soluto” por medio de la masa molar,
así:
56 g de KOH 14 g de KOH
----------------- = ------------------- X = 0,25 mol de KOH
1 mol X
Ahora, de acuerdo con la definición de molaridad, el número de mol debe estar contenido en 1000 mL (o 1 L) de
solución, que es el volumen estándar para esta unidad de concentración, lo que se determina con el siguiente planteamiento:
0,25 mol X
----------------------- = ------------------------- X = 1 mol de KOH
250 mL de solución 1000 mL de solución
Explanation:
Is Trygliceride a saturated or unsaturated molecule? Please explain.
Fats may be either saturated or unsaturated. A saturated fat is a fat that consists of triglycerides whose carbon chains consist entirely of carbon-carbon single bonds. ... An unsaturated fat is a fat that consists of triglycerides whose carbon chains contain one or more carbon-carbon double bonds.
What functional group is found in an alcohol?
A. Ester
B. Amino
C. Carbonyl
D. Hydroxyl
Answer:
an alcohol is a Hydroxyl group due to the OH~ that is associated with it's molecules
The functional group found in an alcohol is Hydroxyl . Therefore, the correct option is option D.
What is functional group?A functional group in organic chemistry is a substituent and moiety inside a molecule that triggers the molecule's distinctive chemical processes. No matter how the rest of a molecule is made up, the very same functional group would experience the same or a similar set of chemical events.
This permits the design of synthetic chemistry as well as the methodical forecasting of chemical reactions as well as the behaviour of chemical molecules. Other functional groups close by can affect a functional group's reactivity. Retrosynthetic analysis can be used to design organic synthesis by using functional group interconversion. The functional group found in an alcohol is Hydroxyl .
Therefore, the correct option is option D.
To know more about functional group, here:
https://brainly.com/question/29263610
#SPJ7
A functional group introduces heteroatoms into a carbon chain to increase
polarity.
chain length.
molecular mass.
reactivity.
Answer:
reactivaty
Explanation:
here you go for the answer
For centuries scientists found evidence that supports the theory of spontaneous generation. Which of the following
supported this theory?
A. The sun rising in the east and seeing in the west.
B. Maggots appearing on rotten meat.
C. The swan-next flask experiment.
D. All living things are made of cells.
Spontaneous generation theory is that living organisms can arise by non living things.
This theory follows the concept of abiogenesis where there is non living parent for a living child.
The appearance of maggots from rotten meat is the idea of abiogenesis, this creates a living organism with a dead parent.
The rotten piece of meat is a non living object but still maggots were formed from this.
Therefore the correct answer is B.
Answer:
a
Explanation:
What volume of 1.50 mol/L stock solution is needed to make 125 mL of 0.60 mol/L solution?
Chemistry 11 Solutions
978Ͳ0Ͳ07Ͳ105107Ͳ1Chapter 8 Solutions and Their Properties • MHR | 85
Amount in moles, n, of the NaCl(s):
NaCl
2.5 g
m
n
M
58.44 g
2
4.2778 10 m l
ol
o
/m
u
Molar concentration, c, of the NaCl(aq):
–2 4.2778 × 10 mol
0.100
0.42778 mol/L
0.43 mol
L
/L
n
c
V
The molar concentration of the saline solution is 0.43 mol/L.
Check Your Solution
The units are correct and the answer correctly shows two significant digits. The
dilution of the original concentrated solution is correct and the change to mol/L
seems reasonable.
Section 8.4 Preparing Solutions in the Laboratory
Solutions for Practice Problems
Student Edition page 386
51. Practice Problem (page 386)
Suppose that you are given a stock solution of 1.50 mol/L ammonium sulfate,
(NH4)2SO4(aq).
What volume of the stock solution do you need to use to prepare each of the
following solutions?
a. 50.0 mL of 1.00 mol/L (NH4)2SO4(aq)
b. 2 × 102 mL of 0.800 mol/L (NH4)2SO4(aq)
c. 250 mL of 0.300 mol/L NH4
+
(aq)
What Is Required?
You need to calculate the initial volume, V1, of (NH4)2SO4(aq) stock solution
needed to prepare each given dilute solution.
The dilution gives the relationship between the molarity and the volume of the solution. The volume of stock solution with a molarity of 1.50 mol/L is 50 mL.
What is dilution?Dilution is said to be the addition of more volume to the concentrated solution to make it less in molar concentration. This tells about the inverse and indirect relationship between the volume and the molar concentration of the solution.
Given,
Initial volume = V₁
Initial molar concentration (M₁) = 1.50 mol/L
Final volume (V₂) = 125 mL = 0.125 L
Final molar concentration (M₂)= 0.60 mol/L
The dilution is calculated as:
M₁V₁ = M₂V₂
V₁ = M₂V₂ ÷ M₁
Substituting the values in the above formula as
V₁ = M₂V₂ ÷ M₁
V₁ = (0.60 mol/L × 0.125 L) ÷ 1.50 mol/ L
V₁ = 0.05 L
= 50 mL
Therefore, 50 mL of stock solution is needed to make a 0.60 mol/L solution.
Learn more about dilution, here:
https://brainly.com/question/15718488
#SPJ2
balance equation of aluminium chloride+ hydrogen
[tex]\boxed{\sf {AlCl_3\atop Aluminium\:Chloride}+{H_2\atop Hydrogen}\longrightarrow {Al\atop Aluminium}+{HCl\atop Hydrochloric\:acid}}[/tex]
Balanced Equation:-
[tex]\boxed{\sf {2AlCl_3\atop Aluminium\:Chloride}+{3H_2\atop Hydrogen}\longrightarrow {2Al\atop Aluminium}+{6HCl\atop Hydrochloric\:acid}}[/tex]
What is the Equation of Reduction in Mg+F2 gives MgF2, I WILL MARK YOU AS BRAINLIST
Answer:
Mg+F2= Mgf2
Explanation:
F 2 is an oxidizing agent, Mg is a reducing agent. ; Pale-yellow to greenish gas with a pungent, irritating odor.
Which of the following will affect the rate of a chemical reaction?
solution temperature
solution color
solute mass
solution volume
Answer:
Solution temperature.
Explanation:
Hello there!
In this case, considering this question about chemical kinetics, it will be possible for us to analyze two perspectives:
1. Molecular: here, we infer that the solution temperature will provide more energy to the molecules in order to undergo more effective crashes which will make more products and therefore, increase the rate constant.
2. Mathematical: by means of the Arrhenius equation, it will be possible to tell that the increase in the temperature of the system, the negative of the exponent present in such equation will increase and therefore turn the rate constant bigger.
In such way, we infer the answer is solution temperature.
Regards!
