Answer:
[tex]D_o=11.9inch[/tex]
Explanation:
From the question we are told that:
Thickness [tex]T=0.5[/tex]
Internal Pressure[tex]P=2.2Ksi[/tex]
Shear stress [tex]\sigma=12ksi[/tex]
Elastic modulus [tex]\gamma= 35000[/tex]
Generally the equation for shear stress is mathematically given by
[tex]\sigma=\frac{P*r_1}{2*t}[/tex]
Where
r_i=internal Radius
Therefore
[tex]12=\frac{2.2*r_1}{2*0.5}[/tex]
[tex]r_i=5.45[/tex]
Generally
[tex]r_o=r_1+t[/tex]
[tex]r_o=5.45+0.5[/tex]
[tex]r_o=5.95[/tex]
Generally the equation for outer diameter is mathematically given by
[tex]D_o=2r_o[/tex]
[tex]D_o=11.9inch[/tex]
Therefore
Assuming that the thin cylinder is subjected to integral Pressure
Outer Diameter is
[tex]D_o=11.9inch[/tex]
Use a truth table to verify the first De Morgan law ¬(p ∧ q) ≡ ¬p ∨ ¬q.
Answer:
p q output ¬(p ∧ q)
0 0 1
0 1 1
1 0 1
0 0 0
p q output ¬p ∨ ¬q
0 0 1
0 1 1
1 0 1
0 0 0
Explanation:
We'll create two separate truth tables for both sides of the equation, and see if they match.
The expressions in the question use AND, OR and NOT operators.
The AND operation needs both inputs to be 1 to return a 1.The OR operation needs at least 1 of the inputs to be 1 to return a 1. The NOT operation takes a 1 and turns it into a 0, or takes a 0 and turns it into a 1.Let's start with ¬(p ∧ q)
NOT (0 AND 0) = NOT (0) = 1NOT (0 AND 1) = NOT (0) = 1NOT (1 AND 0) = NOT (0) = 1NOT (1 AND 1) = NOT (1) = 0Now let's move on to the second expression ¬p ∨ ¬q
NOT(0) OR NOT(0) = 1 OR 1 = 1NOT(0) OR NOT(1) = 1 OR 0 = 1NOT(1) OR NOT(0) = 0 OR 1 = 1NOT(0) OR NOT(0) = 0 OR 0 = 0Therefore we can say the two expressions are equivalent.
Attached the truth table to verify the first De Morgan's law ¬(p ∧ q) ≡ ¬p ∨ ¬q:
What is the explanation of the truth table?As you can see from the attached truth table, the truth values for ¬(p ∧ q) and ¬p ∨ ¬q are the same for all combinations of p and q, confirming the validity of the first De Morgan's law.
De Morgan's law is a fundamental principle in propositional logic.
It states that the negation of a conjunction (AND) is equivalent to the disjunction (OR) of the negations of the individual propositions.
Learn more about truth table at:
https://brainly.com/question/28605215
#SPJ3
Different metabolic control systems have different characteristic time scales for a control response to be achieved. Match the time scale with the control system.
a. Covalent modification
b. Allosteric control
c. Gene expression
1. Seconds to minutes
2. Milliseconds
3. Hours
Answer:
a. Covalent modification = Seconds to minutes
b. Allosteric control = Milliseconds
c. Gene expression = Hours
Explanation:
Covalent modifications refer to the addition and/or removal of chemical groups by the action of particular enzymes such as methylases, acetylases, phosphorylases, phosphatases, etc. For example, histones are chromatin-associated proteins covalently modified by enzymes that add methyl groups (histone methylation), acetyl groups (histone acetylation), phosphate groups (histone phosphorylation), etc. Moreover, allosteric control, also known as allosteric regulation, is a type of regulation of the enzyme activity by binding an effector molecule (allosteric modulator) at a different site than the enzyme's active site, thereby triggering a conformational change on the enzyme upon binding of an effector. Finally, gene expression encompasses the cellular processes by which genetic information flows from genes to proteins (i.e., transcription >> translation). In metabolic pathways, enzymes that are able to catalyze irreversible reactions represent sites of control (for example, during glycolysis, pyruvate kinase is an enzyme that catalyzes an irreversible reaction, thereby serving as a control site). In turn, enzymatic activity is modulated by covalent modifications or reversible binding of allosteric effectors. Finally, metabolic pathways are also modulated by gene regulatory mechanisms that control the transcription of specific enzymes required for such pathways. During these processes, the times required for allosteric regulation, covalent modification (e.g., phosphorylation) and transcriptional control can be counted in milliseconds, seconds, and hours, respectively.
Question # 1
Fill in the Blank
Complete the following sentence.
Mobility refers to the ability to _____.
to move or walk freely and easly
định khoản nghiệp vụ sau : tạm ứng cho nhân viên A đi công tác bằng tiền mặt 50.000
Answer:
report on a fight you have witnessed
Biết op-amp có Vsat = 12V, R1=R2=R3=R4=R, dạng sóng điện áp Vi(t) được cho như
hình 2.16b
a. Tính V0 theo Vi, độ lợi áp AV
b. Vẽ lại dạng sóng điện áp V0(t) khi Vm= 3
8 V
c. Vẽ lại dạng sóng điện áp V0(t) khi Vm = 5V
Answer:
Hello bro
Explanation:
I think i can help you something but can you translate it on english plzz
How many numbers multiple of 3 are in the range [2,2000]?
What are three types of land reform
Answer:
Abolition of intermediaries (rent collectors under the pre-Independence land revenue system); Tenancy regulation (to improve the contractual terms including the security of tenure); A ceiling on landholdings (to redistributing surplus land to the landless);
Types of Land Reform
Abolition of Intermediaries
The first step taken by the Indian government under land reforms post-independence was passing the Zamindari Abolition Act. The primary reason of a backward agrarian economy was the presence of intermediate entities like, jagirdars and zamindar who primarily focussed on collecting sky-rocketing rents catering to their personal benefits, without paying attention to the disposition of farms and farmers. Abolition of such intermediaries not only improved conditions of farmers by establishing their direct connection with the government but also improved agricultural production.
Regulation of Rents
This was in direct response to the unimaginably high rents which were charged by intermediaries during British rule, which resulted in a never-ending cycle of poverty and misery for tenants. Indian government implemented these regulations to protect farmers and labourers from exploitation by placing a maximum limit on the rent that could be charged for land.
Tenure Security
Legislations were passed in all states of the country to grant tenants with permanent ownership of lands and protection from unlawful evictions on expiry of the lease. This law protects tenants from having to vacate a property immediately after their tenure is over unless ordered by law. Even in that case, ownership can be regained by tenants with the excuse of personal cultivation.
Race cars at the Indianapolis Speedway average speeds of 185 mi/h. After determining the altitude of Indianapolis, find the Mach number of these cars and estimate whether compressibility might affect their aerodynamics.
Answer:
- the Mach number is 0.24.
- Compressibility becomes effective when Mach number is greater than 0.3, the Mach number of the race cars is less than 0.3, hence, compressibility will not affect their aerodynamics.
Explanation:
Given the data in the question;
Average speed V = 185 miles per hour = ( 185 /2.237 ) m/s = 82.7 m/s
From Almanac, we can find that Indianapolis is at 220 m altitude.
So from table, at that altitude, the standard speed of sound will be 339.4 m/s .
Mach number of the race car will be;
Mach Number = Velocity / sound speed
we substitute
Mach Number = ( 82.7 m/s ) / ( 339.4 m/s )
Mach Number = 0.24
Therefore the Mach number is 0.24.
We know that, compressibility becomes effective when the Mach number is greater than 0.3.
Since the Mach number of the race cars is less than 0.3, compressibility will not affect their aerodynamics.
A binary system of species 1 and 2 consists of vapor and liquid phases in equilibrium
at temperature T. The overall mole fraction of species 1 in the system is z1 = 0.65. At
temperature T, lnγ1 = 0.67 x2
2; lnγ2 = 0.67 x1
2; P1
sat = 32.27 kPa; and P2
sat = 73.14 kPa.
Assuming the validity of Eq. (13.19),
Final PDF to printer
13.10. Problems 511
smi96529_ch13_450-523.indd 511 01/06/17 03:27 PM
(a) Over what range of pressures can this system exist as two phases at the given T and z1?
(b) For a liquid-phase mole fraction x1 = 0.75, what is the pressure P and what molar
fraction of the system is vapor?
(c) Show whether or not the system exhibits an azeotrope
Question in Probability and Statistics 2
The host at the end of the video claims that ___________ is crucial to his success as a driver. A. Reaction time B. A safe space C. His seat belt
Answer:
answer is C. his seat belt
What is working fluid and mention five example of working fluid.
Answer:
For fluid power, a working fluid is a gas or liquid that primarily transfers force, motion, or mechanical energy. ... Examples without phase change include air or hydrogen in hot air engines such as the Stirling engine, air or gases in gas-cycle heat pumps, etc.
Explanation:
Answer:
A working fluid is a gas or liquid that primarily transfers force, motion or mechanical energy
Examples:Air, pentane, chlorofluorocarbons, butane, propane and ammonia
Explain the LWD process why is it important in drilling operations?
Answer:
Logging while drilling (LWD) is a technique of conveying well logging tools into the well borehole downhole as part of the bottom hole assembly (BHA). ... In these situations, the LWD measurement ensures that some measurement of the subsurface is captured in the event that wireline operations are not possible.
Explanation:
pls mark brainliest
Hot air is to be cooled as it is forced to flow through the tubes exposed to atmospheric air. Fins are to be added in order to enhance heat transfer. Would you recommend attaching the fins inside or outside the tubes? Why? When would you recommend auaching fins both inside and outside the tubes?
Answer:
Fins should be attached outside the tube Fins can be attached on both sides when convection coefficient of air inside the tube is equal to the convection coefficient of atmospheric air outside the tubeExplanation:
The main function of the fins that are to be added is to ensure the speedy transfer of heat from the Hot air.
The fins should be attached outside the tube because the convection coefficient of air is higher inside the tube than the convection coefficient of the outside air ( atmospheric air ), BUT
When convection coefficient of air inside the tube is equal to the atmospheric air outside the tube, it is recommended that the fins can be added on both sides of the tube ( i.e. in and outside the tube )
Future solution for air pollution in new zealand
Answer:
New Zealand may use some of these solutions to prevent air pollution
Explanation:
Using public transports.
Recycle and Reuse
No to plastic bags
Reduction of forest fires and smoking
Use of fans instead of Air Conditioner
Use filters for chimneys
Avoid usage of crackers
What is the built-in pollution control system in an incinerator called
Explanation:
hbyndbnn☝️
Cho thanh có tiết diện thay đổi chịu tải trọng dọc trục (hình 1).
Biết d1 = 5 cm, d2 = 8 cm, a= 15 cm, b=10cm, P1 =400kN, P2 =200kN, E= 2.104 kN/cm2.
a) Vẽ biểu đồ lực dọc.
b) Kiểm tra bền của thanh AC, [ϭ] =10 (kN/cm2).
c) Xác định chuyển vị theo phương dọc trục của tâm tiết diện C
Answer:
saay in English language
Design a ductile iron pumping main carrying a discharge of 0.35 m3/s over a distance of 4 km. The elevation of the pumping station is 140 m and that of the exit point is 150 m. The required terminal head is 10 m. Estimate the pipe diameter and pumping head using the explicit design procedure g
Answer:
[tex]D=0.41m[/tex]
Explanation:
From the question we are told that:
Discharge rate [tex]V_r=0.35 m3/s[/tex]
Distance [tex]d=4km[/tex]
Elevation of the pumping station [tex]h_p= 140 m[/tex]
Elevation of the Exit point [tex]h_e= 150 m[/tex]
Generally the Steady Flow Energy Equation SFEE is mathematically given by
[tex]h_p=h_e+h[/tex]
With
[tex]P_1-P_2[/tex]
And
[tex]V_1=V-2[/tex]
Therefore
[tex]h=140-150[/tex]
[tex]h=10[/tex]
Generally h is give as
[tex]h=\frac{0.5LV^2}{2gD}[/tex]
[tex]h=\frac{8Q^2fL}{\pi^2 gD^5}[/tex]
Therefore
[tex]10=\frac{8Q^2fL}{\pi^2 gD^5}[/tex]
[tex]D=^5\frac{8*(0.35)^2*0.003*4000}{3.142^2*9.81*10}[/tex]
[tex]D=0.41m[/tex]
A route for a proposed 8-m-wide highway crosses a region with a 4-m-thick saturated, soft, normally consolidated clay (CH) above impermeable rock. Groundwater level is 1 m below the surface. The geotechnical data available during the preliminary design stage consist of Atterberg limits (LL 5 68% and PL 5 32%) and the natural water content (w 5 56%). Based on experience, the geotechnical engineer estimated the coefficient of consolidation at 8 m2 per year. To limit settlement, a 4-m-high embankment will be constructed as a surcharge from fill of unit weight 16 kN/m3.
(a) Estimate the compression and recompression indices.
(b) Estimate the total primary consolidation settlement under the center of the embankment.
(c) Plot a time–settlement curve under the center of the embankment.
(d) How many years will it take for 50% consolidation to occur?
(e) Explain how you would speed up the consolidation.
(f) Estimate the rebound (heave) when the surcharge is removed.
Sketch a settlement profile along the base of the embankment. Would the settlement be uniform along the base? Explain your answer.A route for a proposed 8-m-wide highway crosses a
4.3
While a train is standing still, its smoke blows 12 m/s north.
What will the resulting velocity be of the smoke relative to the train if the train
is moving at 25 m/s south?
(3)
Assignment Using Perman's equation, estimate the potential evapotranspiration for the month of August in locality with the following data
latitude 20 degrees north
Elevation 200m
• Mean monthly temperature 20 degreeso
• Mean relative humidity: 75%
• Mean sunshine hour= 9hrs
Wind at 2 m height equal 85 km per day
nature of surface cover =green grass
Answer:
what do you need help with
Explanation:
A(n) ____ combines two planetary gearsets to provide more gear ratio possibilities. A)compound planetary gearset B)orifice C)detent D)lock-up torque converter
Answer:
The answer is A. Compound Planetary Gearset.
Explanation:
The Compound Planetary Gear block represents a planetary gear train with composite planet gears. Each composite planet gear is a pair of rigidly connected and longitudinally arranged gears of different radii. One of the two gears engages the centrally located sun gear while the other engages the outer ring gear.
Compound planetary gear sets have at least two planet gears attached in line to the same shaft, rotating and orbiting at the same speed while meshing with different gears. Compounded planets can have different tooth numbers, as can the gears they mesh with.
a basketball player pushes down with a force of 50N on a basketball that is indlated to a gage pressure of 8.0x10^4 Pa. What is the diameter of comtact between the ball nad the floor
Answer:
The diameter of the contact area between the ball and the floor is approximately 28 milimeters.
Explanation:
The basketball experiments a normal stress ([tex]\sigma[/tex]), in pascals, due to normal force from the floor ([tex]N[/tex]). By definition of normal stress, we have the following equation:
[tex]\sigma = \frac{4\cdot N}{\pi\cdot D^{2}}[/tex] (1)
Where [tex]D[/tex] is the diameter of the contact area between the ball and the floor, in meters.
Please notice that magnitude of the normal force equals the magnitude of external force given by the basketball player and weight is negligible in comparison with normal and external forces.
If we know that [tex]N = 50\,N[/tex] and [tex]\sigma = 8.0\times 10^{4}\,Pa[/tex], then the diameter of the contact area is:
[tex]\sigma = \frac{4\cdot N}{\pi\cdot D^{2}}[/tex]
[tex]D^{2} = \frac{4\cdot N}{\pi\cdot \sigma}[/tex]
[tex]D = 2\cdot \sqrt{\frac{N}{\pi\cdot \sigma} }[/tex]
[tex]D = 2\cdot \sqrt{\frac{50\,N}{\pi\cdot (8\times 10^{4}\,Pa)} }[/tex]
[tex]D\approx 0.028\,m[/tex] [tex](28\,mm)[/tex]
The diameter of the contact area between the ball and the floor is approximately 28 milimeters.
Select the correct statement(s) regarding IEEE 802.16 WiMAX BWA. a. WiMAX BWA describes both 4G Mobile WiMAX and fixed WiMax b. DSSS and CDMA are fundamental technologies used with WiMAX BWA c. OFDM is implemented to increase spectral efficiency and to improve noise performance d. all of the statements are correct
Answer:
d. all of the statements are correct.
Explanation:
WiMAX Broadband Wireless Access has the capacity to provide service up to 50 km for fixed stations. It has capacity of up to 15 km for mobile stations. WiMAX BWA describes both of 4G mobile WiMAX and fixed stations WiMAX. OFMD is used to increase spectral efficiency of WiMAX and to improve noise performance.
4) A steel tape is placed around the earth at the equator when the temperature is 0 C. What will the clearance between the tape and the ground (assumed to be uniform) be if the temperature of the tape rises to 30 C. Neglect the expansion of the earth (the radius of the earth is 6.37 X 106 m)
Answer:
2102.1 m
Explanation:
Temperature at the equator = 0⁰
Radius of the earth = 6.37x10⁶
Required:
We how to find out what the clearance between tape and ground would be if temperature increases to 30 degrees.
Final temperature = ∆T = 303-273 = 30
S = 11x10^-6
The clearance R = Ro*S*∆T
=6.37x10⁶x 11x10^-6x30
= 2102.1m
Or 2.102 kilometers
Thank you
The value of universal gas constant is same for all gases?
a) yes
b)No
Answer:
The answer of these questions is
Explanation:
b) NO
A balanced three-phase inductive load is supplied in steady state by a balanced three-phase voltage source with a phase voltage of 120 V rms. The load draws a total of 10 kW at a power factor of 0.85 (lagging). Calculate the rms value of the phase currents and the magnitude of the per-phase load impedance. Draw a phasor diagram showing all tlme voltages and currents.
Answer:
Following are the solution to the given question:
Explanation:
Line voltage:
[tex]V_L=\sqrt{3}V_{ph}=\sqrt{3}(120) \ v[/tex]
Power supplied to the load:
[tex]P_{L}=\sqrt{3}V_{L}I_{L} \cos \phi[/tex]
[tex]10\times 10^3=\sqrt{3}(120 \sqrt{3}) I_{L}\ (0.85)\\\\I_{L}= 32.68\ A[/tex]
Check wye-connection, for the phase current:
[tex]I_{ph}=I_L= 32.68\ A[/tex]
Therefore,
Phasor currents: [tex]32.68 \angle 0^{\circ} \ A \ ,\ 32.68 \angle 120^{\circ} \ A\ ,\ and\ 32.68 -\angle 120^{\circ} \ A[/tex]
Magnitude of the per-phase load impedance:
[tex]Z_{ph}=\frac{V_{ph}}{I_{ph}}=\frac{120}{32.68}=3.672 \ \Omega[/tex]
Phase angle:
[tex]\phi = \cos^{-1} \ (0.85) =31.79^{\circ}[/tex]
Please find the phasor diagram in the attached file.
Car B is traveling a distance dd ahead of car A. Both cars are traveling at 60 ft/s when the driver of B suddenly applies the brakes, causing his car to decelerate at ft/s^2. It takes the driver of car A 0.75 s to react (this is the normal reaction time for drivers). When he applies his brakes, he decelerates at 18 ft/s^2.
Required:
Determine the minimum distance d between the cars so as to avoid a collision.
Answer:
Explanation:
Using the kinematics equation [tex]v = v_o + a_ct[/tex] to determine the velocity of car B.
where;
[tex]v_o =[/tex] initial velocity
[tex]a_c[/tex] = constant deceleration
Assuming the constant deceleration is = -12 ft/s^2
Also, the kinematic equation that relates to the distance with the time is:
[tex]S = d + v_ot + \dfrac{1}{2}at^2[/tex]
Then:
[tex]v_B = 60-12t[/tex]
The distance traveled by car B in the given time (t) is expressed as:
[tex]S_B = d + 60 t - \dfrac{1}{2}(12t^2)[/tex]
For car A, the needed time (t) to come to rest is:
[tex]v_A = 60 - 18(t-0.75)[/tex]
Also, the distance traveled by car A in the given time (t) is expressed as:
[tex]S_A = 60 * 0.75 +60(t-0.75) -\dfrac{1}{2}*18*(t-0.750)^2[/tex]
Relating both velocities:
[tex]v_B = v_A[/tex]
[tex]60-12t = 60 - 18(t-0.75)[/tex]
[tex]60-12t =73.5 - 18t[/tex]
[tex]60- 73.5 = - 18t+ 12t[/tex]
[tex]-13.5 =-6t[/tex]
t = 2.25 s
At t = 2.25s, the required minimum distance can be estimated by equating both distances traveled by both cars
i.e.
[tex]S_B = S_A[/tex]
[tex]d + 60 t - \dfrac{1}{2}(12t^2) = 60 * 0.75 +60(t-0.75) -\dfrac{1}{2}*18*(t-0.750)^2[/tex]
[tex]d + 60 (2.25) - \dfrac{1}{2}(12*(2.25)^2) = 60 * 0.75 +60((2.25)-0.75) -\dfrac{1}{2}*18*((2.25)-0.750)^2[/tex]
d + 104.625 = 114.75
d = 114.75 - 104.625
d = 10.125 ft
What statement about the print() function is true?
print() has a variable number of parameters.
print() can have only one parameter.
print() can be used to obtain values from the keyboard.
print() does not automatically add a line break to the display.
Explanation:
print() has a variable number of parameters. this is the answer.
hope this helps you
have a nice day
Why water parameters of Buriganga river vary between wet and dry seasons?
Explain.
