Answer:
ωf = 8.8 rad/s
v = 2.2 m/s
Explanation:
We will use the third equation of motion to find the maximum angular velocity of the wheel:
[tex]2\alpha \theta = \omega_f^2 -\omega_I^2[/tex]
where,
α = angular acceleration = 6 rad/s²
θ = angular displacemnt = 1 rev = 2π rad
ωf = max. final angular velocity = ?
ωi = initial angular velocity = 1.5 rad/s
Therefore,
[tex]2(6\ rad/s^2)(2\pi\ rad)=\omega_f^2-(1.5\ rad/s)^2\\\omega_f^2=75.4\ rad/s^2+2.25\ rad/s^2\\\omega_f = \sqrt{77.65\ rad/s^2}[/tex]
ωf = 8.8 rad/s
Now, for linear velocity:
v = rω = (0.25 m)(8.8 rad/s)
v = 2.2 m/s
A cylindrical swimming pool has a radius 2m and depth 1.3m .it is completely filled with salt water of specific gravity 1.03.The atmospheric preassure is 1.013 x 10^5 Pa.
a.calculate the density of salt water.
Answer:
the density of the salt water is 1030 kg/m³
Explanation:
Given;
radius of the cylindrical pool, r = 2 m
depth of the pool, h = 1.3 m
specific gravity of the salt water, γ = 1.03
The atmospheric pressure, P₀ = 1.013 x 10⁵ Pa
Density of fresh water, [tex]\rho _w[/tex] = 1000 kg/m³
The density of the salt water is calculated as;
[tex]Specific \ gravity \ of \ salt\ water \ (\gamma _s_w) = \frac{density \ of \ salt \ water \ (\rho_{sw})}{density \ of \ fresh \ water \ (\rho_{w})} \\\\1.03 = \frac{\rho_{sw}}{1000 \ kg/m^3}\\\\\rho_{sw} = 1.03 \times 1000 \ kg/m^3\\\\\rho_{sw} = 1030 \ kg/m^3[/tex]
Therefore, the density of the salt water is 1030 kg/m³
What is the volume of a metal block 3cm long by 2cm wide by 4cm high? What would be the volume of a block twice as long, wide, and high?
Answer:
Volume of a metal block = 24 cm^3
Volume of a block twice as long, wide and high = 192 cm^3
Explanation:
Volume of a block is measured in l*w*h and in the first block, the sides are 3, 2 and 4 and 3*2*4 = 24
Second block, just double each of the lengths to get 6*4*8 = 192
A man standing in an elevator holds a spring scale with a load of 5 kg suspended from it. What would be the reading of the scale, if the elevator is accelerating downward with an acceleration 3.8 m/s?.
Answer:
3.1 kg
Explanation:
Applying,
R = m(g-a)..................... Equation 1
Where R = weight of the scale when the elevator is coming down, a = acceleration of the elevator, g = acceleration due to gravith.
From the question,
Given: m = 5 kg, a = 3.8 m/s²
Constant: g = 9.8 m/s²
Substitute these values into equation 1
R = 5(9.8-3.8)
R = 5(6)
R = 30 N
Hence the spring scale is
m' = R/g
m' = 30/9.8
m' = 3.1 kg
Cuando el pistón tiene un volumen de 2x10^-4 m^3, el gas en el pistón está a una presión de 150 kPa. El área del pistón es 0.00133 m^2. Calcular la fuerza que el gas ejerce sobre el embolo del pistón.
Answer:
F = 1.128 10⁸ Pa
Explanation:
Pressure is defined by
P = F / A
If the gas is ideal for equal force eds on all the walls, so on the piston area we have
F = P A
We reduce the pressure to the SI system
P = 150 kpa (1000 Pa / 1kPa = 150 103 Pa
we calculate
F = 150 10³ / 0.00133
F = 1.128 10⁸ Pa
A space ship has four thrusters positioned on the top and bottom, and left and right as shown below. The thrusters can be operated independently or together to help the ship navigate in all directions.
Initially, the Space Probe is floating towards the East, as shown below, with a velocity, v. The pilot then turns on thruster #2.
Select one:
a.
Space ship will have a velocity to the West and will be speeding up.
b.
Space ship will have a velocity to the East and will be speeding up.
c.
Space ship will have a velocity to the East and will be slowing down.
d.
Space ship will have a velocity to the West and will be slowing down.
e.
Ship experiences no change in motion.
Answer:
The correct answer is - c. Spaceship will have a velocity to the East and will be slowing down.
Explanation:
In this case, if turned on thruster #2 then it will exert force on the west side as thruster 2 is on the east side and it can be understood by Newton's third law that says each action has the same but opposite reaction.
As the spaceship engine applies force on the east side then according to the law the exhauster gas applies on towards west direction. It will try to decrease the velocity of the spaceship however, the direction of floating still be east side initally.
Q)what are convex mirrors?
Answer:
A curved mirror is a mirror with a curved reflecting surface. The surface may be either convex or concave. Most curved mirrors have surfaces that are shaped like part of a sphere, but other shapes are sometimes used in optical devices.
A convex mirror (or lens) is one constructed so that it is thicker in the middle than it is at the edge.
Suppose a 60-turn coil lies in the plane of the page in a uniform magnetic field that is directed out of the page. The coil originally has an area of 0.325 m2. It is stretched to have no area in 0.100 s. What is the magnitude (in V) and direction (as seen from above) of the average induced emf if the uniform magnetic field has a strength of 1.60 T
Answer:
emf = 312 V
Explanation:
In this exercise the electromotive force is asked, for which we must use Faraday's law
emf = [tex]- N \frac{d \Phi }{dt}[/tex]- N dfi / dt
Ф = B. A = B A cos θ
bold type indicates vectors.
They indicate that the magnetic field is constant, the angle between the normal to the area and the magnetic field is parallel by local cosine values 1
It also indicates that the area is reduced from a₀ = 0.325 me² to a_f = 0 in a time interval of ΔT = 0.100 s, suppose that this reduction is linear
emf = -N B [tex]\frac{dA}{dT}[/tex]
emf = - N B (A_f - A₀) / Dt
we calculate
emf = - 60 1.60 (0 - 0.325) /0.100
emf = 312 V
The direction of this voltage is exiting the page
5. Steve is driving in his car to take care of some errands. The first errand has him driving to a location 2 km East and 6 km North of his starting location. Once he completes that errand, he drives to the second one which is 4 km East and 2 km South of the first errand. What is the magnitude of the vector that describes how far the car has traveled from its starting point, rounded to the nearest km?
Answer:
gshshs
Explanation:
hshsksksksbsbbshd
A 1.5kg block slides along a frictionless surface at 1.3m/s . A second block, sliding at a faster 4.3m/s , collides with the first from behind and sticks to it. The final velocity of the combined blocks is 2.0m/s . What was the mass of the second block?
Answer:
The mass of the second block=0.457 kg
Explanation:
We are given that
m1=1.5 kg
v1=1.3m/s
v2=4.3 m/s
V=2.0 m/s
We have to find the mass of the second block.
[tex]m_1v_1+m_2v_2=(m_1+m_2)V[/tex]
Let m2=m
Substitute the values
[tex]1.5(1.3)+m(4.3)=(1.5+m)(2)[/tex]
[tex]1.95+4.3m=3+2m[/tex]
[tex]4.3m-2m=3-1.95[/tex]
[tex]2.3m=1.05[/tex]
[tex]m=\frac{1.05}{2.3}[/tex]
[tex]m=0.457 kg[/tex]
Hence, the mass of the second block=0.457 kg
. A ball of mass 0.50 kg is rolling across a table top with a speed of 5.0 m/s. When the ball reaches the edge of the table, it rolls down an incline onto the floor 1.0 meter below (without bouncing). What is the speed of the ball when it reaches the floor?
Answer:
4
Explanation:
the plane of a 5.0 cm by 8.0 cm rectangular loop wire is parallel to a 0.19 t magnetic field. if the loop carries a current of 6.2 amps, what is the magnitude of the torque on the loop
Why we use semiconductor instead of metal in thermopile.
Answer:
Semiconductors are not normal materials. They have special properties which conductors/metals cannot exhibit. The main reason for the behavior of semiconductors is that they have paired charge carriers-the electron-hole pair. This is not available in metals.
the rate of cooling determines ....... and ......
Answer:
freezing point and melting point
i don't understand this, can someone help please??
Explanation:
N2 + H2 --> NH3
balance them:
N2 + 3 H2 --> 2 NH3
so if 6 moles of N2 react, 12 moles of NH3 will form.
(you have to look at the big number in front, in this case its N2 and 2 NH3, therefore the amount of N2 will produce double the amount of NH3 )
Two forces are acting on a body. One acts east, the other at 35° north of east. If the
two forces are equal in magnitude of 50 N, find the resultant using the Law of Sines
and the Law of Cosines. Please answer with full solution. Thanks
A=B=50NAngle=theta=35°
We know
[tex]\boxed{\sf R=\sqrt{A^2+B^2+2ABcos\Theta}}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{50^2+50^2+2(50)(50)cos35}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{2500+2500+2(2500)\times (-0.9)}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{5000+5000(-0.9)}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{5000+(-4500)}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{5000-4500}[/tex]
[tex]\\ \sf\longmapsto R=\sqrt{-500}[/tex]
[tex]\\ \sf\longmapsto R=22.4i[/tex]
Resultant using the Law of Sines and the Law of Cosines will be R=95 N
What is force?Force is an external agent applied on any object to displace it from its position. Force is a vector quantity, so with magnitude it also requires direction. Direction is necessary to examine the effect of the force and to find the equilibrium of the force.
The Magnitude of two forces =50 N
Angle between the forces = 35
By using the resultant formula
[tex]\rm R=\sqrt{A^2+B^2+2ABCos\theta}[/tex]
[tex]\rm R=\sqrt{50^2+50^2+2(50)(50)Cos35}[/tex]
[tex]\rm R=\sqrt{5000+5000(0.81)}[/tex]
[tex]\rm R=\sqrt{5000+4500}[/tex]
[tex]\rm R=95\ N[/tex]
Hence the Resultant using the Law of Sines and the Law of Cosines will be R=95 N
To know more about force follow
https://brainly.com/question/25239010
When the drag force on an object falling through the air equals the force of gravity, the object has reached
terminal force.
terminal acceleration,
terminal illness.
terminal velocity
A 20 N south magnetic force pushes a charged particle traveling with a velocity of 4 m/s west through a 5 T magnetic field pointing downwards . What is the charge of the particle ?
Answer:
Charge of the particle is 1 coulomb.
Explanation:
Force, F:
[tex]{ \bf{F=BeV}}[/tex]
F is magnetic force.
B is the magnetic flux density.
e is the charge of the particle.
V is the velocity
[tex]{ \sf{20 = (5 \times e \times 4)}} \\ { \sf{20e = 20}} \\ { \sf{e = 1 \: coulomb}}[/tex]
A uniform magnetic field passes through a horizontal circular wire loop at an angle 15.1° from the normal to the plane of the loop. The magnitude of the magnetic field is 3.35 T , and the radius of the wire loop is 0.240 m . Find the magnetic flux Φ through the loop.
Answer:
0.5849Weber
Explanation:
The formula for calculating the magnetic flus is expressed as:
[tex]\phi = BAcos \theta[/tex]
Given
The magnitude of the magnetic field B = 3.35T
Area of the loop = πr² = 3.14(0.24)² = 0.180864m²
angle of the wire loop θ = 15.1°
Substitute the given values into the formula:
[tex]\phi = 3.35(0.180864)cos15.1^0\\\phi =0.6058944cos15.1^0\\\phi =0.6058944(0.9655)\\\phi = 0.5849Wb[/tex]
Hence the magnetic flux Φ through the loop is 0.5849Weber
if C is The vector sum of A and B C = A + B What must be true about The directions and magnitudes of A and B if C=A+B? What must be tre about the directions and magnitudes of A and B if C=0?
Check attached photo
Check attached photo
Answer:
Explanation:
1. If C = A + B then the lines A and B may have the same magnitude or they may not. The direction of A for example may be northwest ↖️ and the direction of B must be south ⬇️ because the arrow of A and the point of B must connect. Then C’s direction is west ⬅️ because it shouldn’t be as equilibrium.
2. If C = 0 t means the force is at equilibrium. That means all forces add up to zero. A’s direction for example may be northeast ↗️ and the direction of B may be south ⬇️ and the direction of C must be west if it has to be at equilibrium.
The magnitude of A and B must be equal
two bodies A and B with some asses 20 kg and 30 kg respectively above the ground which have greater potential
Answer:
B has greater potential
Explanation:
We know;
Potential Energy (PE) = mgh
where, m=mass of body
g=acceleration due to gravity
h=height of body
From the formula,
PE is directly proportional to the mass of the body
so the body with greater mass has greater potential.
The time delay between transmission and the arrival of the reflected wave of a signal using ultrasound traveling through a piece of fat tissue was 0.13 ms. At what depth did this reflection occur? (The average propagation speed for sound in body tissue is 1540 m/s)
Answer:
10.01 cm
Explanation:
Given that,
The time delay between transmission and the arrival of the reflected wave of a signal using ultrasound traveling through a piece of fat tissue was 0.13 ms.
The average propagation speed for sound in body tissue is 1540 m/s.
We need to find the depth when the reflection occur. We know that, the distance is double when transmitting and arriving. So,
[tex]v=\dfrac{2d}{t}\\\\d=\dfrac{vt}{2}\\\\d=\dfrac{1540\times 0.13\times 10^{-3}}{2}\\\\d= $$0.1001\ m[/tex]
or
d = 10.01 cm
So, the reflection will occur at 10.01 cm.
The paper dielectric in a paper-and-foil capacitor is 0.0785 mm thick. Its dielectric constant is 2.35, and its dielectric strength is 49.5 MV/m. Assume that the geometry is that of a parallel-plate capacitor, with the metal foil serving as the plates.
Required:
a. What area of each plate is required for for a 0.300 uF capacitor?
b. If the electric field in the paper is not to exceed one-half the dielectric strength, what is the maximum potential difference that can be applied across the compactor?
Answer:
a) required area is 1.1318 m²
b) the maximum potential difference that can be applied across the compactor is 1931.1 V
Explanation:
Given the data in the question;
dielectric constant εr = 2.35
distance between plates ( thickness ) d = 0.0785 mm = 7.85 × 10⁻⁵ m
dielectric strength = 49.5 MV/m
a)
given that capacity capacitor C = 0.3 uF = 0.3 × 10⁻⁶ F
To find the Area, we use the following the expression.
C = ε₀εrA / d
we know that The permittivity of free space, ε₀ = 8.854 x 10⁻¹² (F/m)
we substitute
0.3 × 10⁻⁶ = [ (8.854 x 10⁻¹²) × 2.35 × A ] / 7.85 × 10⁻⁵
A = [ (0.3 × 10⁻⁶) × (7.85 × 10⁻⁵) ] / [ 2.35 × (8.854 x 10⁻¹²) ]
A = 2.355 × 10⁻¹¹ / 2.08069 × 10⁻¹¹
A = 1.1318 m²
Therefore, required area is 1.1318 m²
b)
the maximum potential difference that can be applied across the compactor.
We use the following expression;
⇒ 1/2 × dielectric strength × thickness d
we substitute
⇒ 1/2 × ( 49.5 × 10⁶ V/m ) × ( 7.85 × 10⁻⁵ m )
⇒ 1931.1 V
Therefore, the maximum potential difference that can be applied across the compactor is 1931.1 V
A 34-m length of wire is stretched horizontally between two vertical posts. The wire carries a current of 68 A and experiences a magnetic force of 0.16 N. Find the magnitude of the earth's magnetic field at the location of the wire, assuming the field makes an angle of 72.0° with respect to the wire.
Answer:
7.28×10⁻⁵ T
Explanation:
Applying,
F = BILsin∅............. Equation 1
Where F = magnetic force, B = earth's magnetic field, I = current flowing through the wire, L = Length of the wire, ∅ = angle between the field and the wire.
make B the subject of the equation
B = F/ILsin∅.................. Equation 2
From the question,
Given: F = 0.16 N, I = 68 A, L = 34 m, ∅ = 72°
Substitute these values into equation 2
B = 0.16/(68×34×sin72°)
B = 0.16/(68×34×0.95)
B = 0.16/2196.4
B = 7.28×10⁻⁵ T
distance of distinct vision.
is placed at a distance less than the distance of near point, its image o
will be blurred. Hence human eye can not see such object clearly.
ADDITIONAL INFORMATION
distance of distinct vision for a normal eye of different age groups
Babies = 7 cm
Adults = 25 cm
erson of age 55 years and above = 100 cm
ever, in our discussion we are concerned with a normal eye of an adult so least
The foulart position of an ahiect from a human eve so that the sh
The least distance up to which we can see the objects clearly without any strain is called least distance of distinct vision. Least distance of distinct vision for a normal human being is 25cm. For young people, the least distance of distant vision will be within 25cm which however it varies with age.
Answer:
25 you said ? thats incorecct
Explanation:
What is the meant of by renewable energy and non-renewrable with example of each.
Answer:
Renewable energy is a type of energy that can be renewed easily, such as sunlight. By using Solar panels to collect the suns energy, we are not depleting it, so this source is renewable.
Non-renewable energy is something that cannot easily be replenished. An example would be oil because oil takes millions of years to form and cannot be renewed easily.
Wind instruments like trumpets and saxophones work on the same principle as the "tube closed on one end" that we examined in our last experiment. What effect would it have on the pitch of a saxophone if you take it from inside your house (at 76 degrees F) to the outside on a cold day when the outside temperature is 45 degrees F ?
Answer:
The correct answer would be - Low pitch.
Explanation:
As it is known that if frequency increases then pitch will be increase as well as pitch depends on frequency, Now for the question it is mentioned that the tube closed on one end frequency is:
f = v/2l
Where,
l = length of the tube
v = velocity of longitudinal wave of gas filled in the tube
Now increase with the temperature the density of the gas decreases and velocity v is inversely proportional to density of gas so velocity increases. So if there is an increase in frequency so pitch also increases. As the temperature inside the house is at 750 F more than outsideat 450 Fso pitch is more inside and the pitch is low outside.
derive expression for pressure exerted by gas
1) Consider an electric power transmission line that carries a constant electric current of i = 500 A. The cylindrical copper cable used to transmit this current has a diameter o = 2.00 cm and a length L = 150 km. If there are 8.43x10^28 free electrons per cubic meter (m^3 ) in the cable, calculate how long it would take for an electron to cross the entire length of the transmitter line.
Answer:
t = 1.27 x 10⁹ s
Explanation:
First, we will find the volume of the wire:
Volume = V = AL
where,
A = Cross-sectional area of wire = πr² = π(1 cm)² = π(0.01 m)² = 3.14 x 10⁻⁴ m²
L = Length of wire = 150 km = 150000 m
Therefore,
V = 47.12 m³
Now, we will find the number of electrons in the wire:
No. of electrons = n = (Electrons per unit Volume)(V)
n = (8.43 x 10²⁸ electrons/m³)(47.12 m³)
n = 3.97 x 10³⁰ electrons
Now, we will use the formula of current to find out the time taken by each electron to cross the wire:
[tex]I =\frac{q}{t}[/tex]
where,
t = time = ?
I = current = 500 A
q = total charge = (n)(chareg on one electron)
q = (3.97 x 10³⁰ electrons)(1.6 x 10⁻¹⁹ C/electron)
q = 6.36 x 10¹¹ C
[tex]500\ A = \frac{6.36\ x\ 10^{11}\ C}{t}\\\\t = \frac{6.36\ x\ 10^{11}\ C}{500\ A}[/tex]
Therefore,
t = 1.27 x 10⁹ s
A bird has a kinetic energy of 3 J and a potential energy of 25 J. What is the mechanical energy of the bird?
Answer:
28 j
Explanation:
because when you add you get 28
An ideal parallel plate capacitor with a cross-sectional area of 0.4 cm2 contains a dielectric with a dielectric constant of 4 and a dielectric strength of 2 x 108 V/m. The separation between the plates of the capacitor is 5 mm. What is the maximum electric charge (in nC) that can be stored in the capacitor before dielectric breakdown
Answer: [tex]283.2\times 10^{-9}\ nC[/tex]
Explanation:
Given
Cross-sectional area [tex]A=0.4\ cm^2[/tex]
Dielectric constant [tex]k=4[/tex]
Dielectric strength [tex]E=2\times 10^8\ V/m[/tex]
Distance between capacitors [tex]d=5\ mm[/tex]
Maximum charge that can be stored before dielectric breakdown is given by
[tex]\Rightarrow Q=CV\\\\\Rightarrow Q=\dfrac{k\epsilon_oA}{d}\cdot (Ed)\quad\quad [V=E\cdot d]\\\\\Rightarrow Q=k\epsilon_oAE\\\\\Rightarrow Q=4\times 8.85\times 10^{-12}\times 0.4\times 10^{-4}\times 2\times 10^8\\\\\Rightarrow Q=28.32\times 10^{-8}\\\\\Rightarrow Q=283.2\times 10^{-9}\ nC[/tex]
Answer:
The maximum charge is 7.08 x 10^-8 C.
Explanation:
Area, A = 0.4 cm^2
K = 4
Electric field, E = 2 x 10^8 V/m
separation, d = 5 mm = 0.005 m
Let the capacitance is C and the charge is q.
[tex]q = CV\\\\q=\frac{\varepsilon o A}{d}\times E d\\\\q = \varepsilon o A E\\\\q = 8.85\times 10^{-12}\times0.4\times 10^{-4}\times 2\times 10^8\\\\q = 7.08\times 10^{-8}C[/tex]
