Answer: check answers in pictures (2 p)
The resistance of the shunt required for a full-scale deflection of 20 A is 2.528 Ohm.
What is resistance?Resistance is a measure of an electrical circuit's resistance to current flow. Resistance is measured in ohms, which is represented by the Greek letter omega.
Full-scale deflection current = 0.015 A
Full-scale deflection current for 20 A = 20/0.015 = 1333.33 times full-scale deflection current
The current through the meter coil is given by:
Ic = Im * (Rm / (Rm + Rs))
At full scale, Ic = 1333.33 * 0.015 A = 20 A, Rm = 1.5 Ohm, and Rs = 3.5 Ohm.
Therefore:
20 A = Im * (1.5 Ohm / (1.5 Ohm + 3.5 Ohm))
Im = 20 A * (3.5 Ohm / 5 Ohm)
Im = 14 A
The current through the shunt resistor is therefore:
Ish = Im - Ic
Ish = 14 A - 20 A
Ish = -6 A
Since the shunt resistor is in parallel with the meter, its resistance can be calculated using the following formula:
Rs = Rm * (Im / Ish - 1)
Substituting the values, we get:
3.5 Ohm = 1.5 Ohm * (14 A / (-6 A) - 1)
3.5 Ohm = 1.5 Ohm * (-1.333 - 1)
3.5 Ohm = 1.5 Ohm * (-2.333)
Rs = 1.5 Ohm * (14 A / (-6 A) - 1) / (-2.333)
Rs = 2.528 Ohm
Therefore, the resistance of the shunt required for a full-scale deflection of 20 A is 2.528 Ohm.
Now, let's find the resistance required for a full-scale deflection of 250 V:
Full-scale deflection current = 0.015 A
Resistance required for full-scale deflection of 250 V = 250 V / 0.015 A
Resistance required for full-scale deflection of 250 V = 16666.67 Ohm
This resistance is in parallel with the meter coil, so the total resistance in the circuit will be:
Rtotal = Rm || Rext
Rtotal = (Rm * Rext) / (Rm + Rext)
Substituting the values, we get:
Rtotal = (1.5 Ohm * 16666.67 Ohm) / (1.5 Ohm + 16666.67 Ohm)
Rtotal = 1.43 Ohm
This resistance is in series with the meter coil, so the total resistance in the circuit will be:
Rtotal = Rm + Rext + Rs
Substituting the values we get:
1.43 Ohm = 1.5 Ohm + 16666.67 Ohm + Rs
Rs = 1.43 Ohm - 1.5 Ohm - 16666.67 Ohm
Rs = -16666.74 Ohm
Thus, the calculated value of Rs is negative, it means that the shunt resistor must be used instead of a series resistor to achieve a full-scale deflection of 250 V.
For more details regarding resistance, visit:
https://brainly.com/question/29427458
#SPJ2
If OSHA determines that an employer's response to a non-formal complaint is adequate, what options does the employee filing the non-formal complaint have?
Explain moment of inertia
Answer:
The moment of inertia is basically a physical quantity which describes how easy it is for a body to rotate itself around a given axis.
In easier wording: Moment of Inertia is a body and when it starts rotating or moving, it will keep doing so until we stop it by force.
Explanation:
For example, a car that is moving and active will continue to move even if you were to switch the engine off.
To avoid a possible collision with a manned airplane, you climb your unmanned aircraft to yield the right of way. In doing so, your unmanned aircraft reached an altitude greater than 600 feet AGL. To whom must you report the deviation?
Answer:
you have to report to the federal aviation administration upon request
Explanation:
An unmanned aircraft can also be a drone it is an aircraft that does not have passengers or a human pilot.
Such an aircraft could be fully autonomous but most times they have a human pilot who controls it remotely.
Now you have to report this deviation to the federal aviation administration. This body is responsible for the enforcement of regulations that have to do with the manufacture, operation and maintenance of aircrafts. The body makes sure there is an efficient and safe system for a navigation and they also control air traffic.
Solve using Matlab the problems:
One using the permutation of n objects formula
One using the permutation of r objects out of n objects
You can pick these problems from the textbook or you can make up your own questions.
Help me pleaseeeee
Answer:
Explanation:
% Clears variables and screen
clear; clc
% Asks user for input
n = input('Total number of objects: ');
r = input('Size of subgroup: ');
% Computes and displays permutation according to basic formulas
p = 1;
for i = n - r + 1 : n
p = p*i;
end
str1 = [num2str(p) ' permutations'];
disp(str1)
% Computes and displays combinations according to basic formulas
str2 = [num2str(p/factorial(r)) ' combinations'];
disp(str2)
=================================================================================
Example: check
How many permutations and combinations can be made of the 15 alphabets, taking four at a time?
The answer is:
32760 permutations
1365 combinations
==================================================================================
Question in Statistics and Probability 2
Petrol samples were taken at three different stations along a national highway to determine whether the octane rating varied from one station to another. Six petrol specimens of the same category were randomly selected at each station in different days. We are interested to know if there is sufficient evidence to indicate a difference in the mean octane rating at the different stations.
State the Null and the Alternative Hypotheses.
A one electron species, Xm, where m is the charge of the one electron species and X is the element symbol, loses its one electron from its ground state when it absorbs 7.84×10−17 J of energy. Using the prior information, the charge of the one electron species is?
Answer:
c +5
Explanation:
we have difference in energy =
2.18x10⁻¹⁸ x z² / n²
now n = 1
amount of energy absorbed Δdelta = 7.84×10−17 J
7.84×10⁻¹⁷ = 2.18x10⁻¹⁸ x z²
we divide through by 2.18x10⁻¹⁸
z² = 7.84×10⁻¹⁷ / 2.18x10⁻¹⁸
z² = 35.9633
z = √35.9633
z = 5.9969
≈ 6
charge = atomic number 6 - number of electrons available in the element 1
= 6-1 = 5
from the calculations above, the charge of the one electron specie would be c +5
Different metabolic control systems have different characteristic time scales for a control response to be achieved. Match the time scale with the control system.
a. Covalent modification
b. Allosteric control
c. Gene expression
1. Seconds to minutes
2. Milliseconds
3. Hours
Answer:
a. Covalent modification = Seconds to minutes
b. Allosteric control = Milliseconds
c. Gene expression = Hours
Explanation:
Covalent modifications refer to the addition and/or removal of chemical groups by the action of particular enzymes such as methylases, acetylases, phosphorylases, phosphatases, etc. For example, histones are chromatin-associated proteins covalently modified by enzymes that add methyl groups (histone methylation), acetyl groups (histone acetylation), phosphate groups (histone phosphorylation), etc. Moreover, allosteric control, also known as allosteric regulation, is a type of regulation of the enzyme activity by binding an effector molecule (allosteric modulator) at a different site than the enzyme's active site, thereby triggering a conformational change on the enzyme upon binding of an effector. Finally, gene expression encompasses the cellular processes by which genetic information flows from genes to proteins (i.e., transcription >> translation). In metabolic pathways, enzymes that are able to catalyze irreversible reactions represent sites of control (for example, during glycolysis, pyruvate kinase is an enzyme that catalyzes an irreversible reaction, thereby serving as a control site). In turn, enzymatic activity is modulated by covalent modifications or reversible binding of allosteric effectors. Finally, metabolic pathways are also modulated by gene regulatory mechanisms that control the transcription of specific enzymes required for such pathways. During these processes, the times required for allosteric regulation, covalent modification (e.g., phosphorylation) and transcriptional control can be counted in milliseconds, seconds, and hours, respectively.
Can you help me check on which platform is this website created on -
https://www.virtualoplossing.info/
Answer:
It is created on Microsoft Edge
Explanation:
what is the term Self-induced EMF (Induction)
Self induction and Mutual induction
If the current through the coil changes, the flux through the coil changes and an emf is induced. Since the emf is induced in the coil due to its own field, it is called self–induced emf and the phenomenon is called self–induction.
Answer:
Self induced EMF is the electro-motive force that is generated due to change in flux in the coil caused by the change in current in the same coil.
Which of the following is not a category of electrical burns
The load on a bolt consists of an axial pull of 10 KN together with a transverse shear force of 5 KN. Find the diameter of bolt required according to I. Maximum principal stress theory; 2. Maximum shear stress theory; 3. Maximum principal strain theory, 4. Maximum strain energy theory, and 5 Maximum distortion energy theory. Take permissible tensile stress at elastic limit = 100 MPa and poisson's ratio = 0.3
Answer:
hey. its a big question. solved from *c hegg
Explanation:
The input sin(20) is sampled at 20 ms intervals by using impulse train sampling: i. Construct the input and sampled signal spectra.
Solution :
Let [tex]$x(t) = \frac{\sin (20 \pi t)}{\pi t}$[/tex]
[tex]$T_s = 20$[/tex] ms, so [tex]$f_s=\frac{1}{T_s}[/tex]
[tex]$=\frac{1}{20}$[/tex]
= 0.05 kHz
[tex]$f_s=50 $[/tex] Hz , ws = [tex]$2 \pi f_s = 100 \pi$[/tex] rad/s
We know that,
FT → [tex]$\frac{\sin (20 \pi \omega)}{\pi \omega}$[/tex]
The sampled signal is :
[tex]$XS(\omega) = \frac{1}{T_s} \sum_{k=- \infty}^{\infty}X (\omega-k\omega S)[/tex]
So, [tex]$XS(\omega) = \frac{1}{20 \times 10^{-3}} \sum_{k=- \infty}^{\infty}X (\omega-100 k \pi)[/tex]
[tex]$XS(\omega) = 50 \sum_{k=- \infty}^{\infty}X (\omega-100 k \pi)[/tex]
Question # 1
Fill in the Blank
Complete the following sentence.
Mobility refers to the ability to _____.
to move or walk freely and easly
Carbon dioxide at a temperature of 0oC and a pressure of 600 kPa (abs) flows through a horizontal 40-mm- diameter pipe with an average velocity of 2 m/s. Determine the friction factor if the pressure drop is 235 N/m2 per 10-m length of pipe.
Answer:
f = 0.04042
Explanation:
temperature = 0°C = 273k
p = 600 Kpa
d = 40 millemeter
e = 10 m
change in P = 235 N/m²
μ = 2m/s
R = 188.9 Nm/kgk
we solve this using this formula;
P = ρcos*R*T
we put in the values into this equation
600x10³ = ρcos * 188.9 * 273
600000 = ρcos51569.7
ρcos = 600000/51569.7
=11.63
from here we find the head loss due to friction
Δp/pg = feμ²/2D
235/11.63 = f*10*4/2*40x10⁻³
20.21 = 40f/0.08
20.21*0.08 = 40f
1.6168 = 40f
divide through by 40
f = 0.04042
Tech A says that the voltage regulator controls the strength of the rotor s magnetic field. Tech B says that the voltage regulator is installed between the output terminal of the alternator and the positive terminal of the battery. Who is correct?
Answer:
Voltage Regulator
Technician A is correct.
Explanation:
Technician B is not correct. The voltage regulator is not installed between the output terminal of the alternator and the positive terminal of the battery as claimed by Technician B. Technician A's opinion that the voltage regulator controls the strength of the rotor's magnetic field is correct. The computer can also be used to control the output of the alternator by controlling the field current.
5-2 discussion: the role of communication in success
Answer:
Answer to the following question is as follows;
Explanation:
It is critical to communicate well during negotiations and conversation in order to attain your objectives. Communication also becomes essential in business and corporation . Effective communication may help you as well as your employees develop a strong professional relationship, which can boost morale and efficiency.
“Snow Cover Area change Analysis for Kabul Basin”
Summarize how GIS & Remote Sensing is incorporated in this study.
GIS
The full for GIS is : Geographic Information System.
The GIS is a system of mapping that is used to create, analyze, manage and map all the types of data.
It is a method capturing, checking as well as displaying all the data that is related to the position of the surface of earth.
Remote Sensing
Remote sensing is defined as a process where the various physical characteristics of an area are constantly monitored and detected by a process of measuring the reflection of the emitted radiations at ta distance.
The snow covered areas of the Kabul basin can be monitored and analyzed by using the process of GIS and remote sensing.
They provide a continuous source of information and data about snow covered peaks, the amount of snow to the authorities.
Learn More :
https://brainly.in/question/1556256?__cf_chl_captcha_tk__=pmd_2d2d9994422ca43d3cbbcf6322e6c34da175405a-1628654009-0-gqNtZGzNAvijcnBszQ3i
Consider CO at 500 K and 1000 kPa at an initial state that expands to a final pressure of 200 kPa in an isentropic manner. Report the final temperature in units of K and using three significant digits.
Answer:
[tex]T_2=315.69k[/tex]
Explanation:
Initial Temperature [tex]T_1=500K[/tex]
Initial Pressure [tex]P_1=1000kPa[/tex]
Final Pressure [tex]P_2=200kPa[/tex]
Generally the gas equation is mathematically given by
[tex]\frac{T_2}{T_1}=\frac{P_2}{P_1}^{\frac{n-1}{n}}[/tex]
Where
n for [tex]CO=1.4[/tex]
Therefore
[tex]\frac{T_2}{500}=\frac{200}{1000}^{\frac{1.4-1}{1.4}}[/tex]
[tex]T_2=315.69k[/tex]
Which statement describes the relay between minerals and rocks ?
Answer:
•○●□■hey hi!■□●○•Explanation:
Minerals and rocks are the same. Aggregates of minerals form rocks. Minerals determine the texture of a rock. Most rocks are made of a single mineral type.
☆♡hope this helps♡☆8.50 nC of charge is uniformly distributed along a thin rod of length L = 9.20 cm, which is then bent into a semicircle. What is the magnitude of the electric field at the center of the circle
định khoản nghiệp vụ sau : tạm ứng cho nhân viên A đi công tác bằng tiền mặt 50.000
Answer:
report on a fight you have witnessed
Use a truth table to verify the first De Morgan law ¬(p ∧ q) ≡ ¬p ∨ ¬q.
Answer:
p q output ¬(p ∧ q)
0 0 1
0 1 1
1 0 1
0 0 0
p q output ¬p ∨ ¬q
0 0 1
0 1 1
1 0 1
0 0 0
Explanation:
We'll create two separate truth tables for both sides of the equation, and see if they match.
The expressions in the question use AND, OR and NOT operators.
The AND operation needs both inputs to be 1 to return a 1.The OR operation needs at least 1 of the inputs to be 1 to return a 1. The NOT operation takes a 1 and turns it into a 0, or takes a 0 and turns it into a 1.Let's start with ¬(p ∧ q)
NOT (0 AND 0) = NOT (0) = 1NOT (0 AND 1) = NOT (0) = 1NOT (1 AND 0) = NOT (0) = 1NOT (1 AND 1) = NOT (1) = 0Now let's move on to the second expression ¬p ∨ ¬q
NOT(0) OR NOT(0) = 1 OR 1 = 1NOT(0) OR NOT(1) = 1 OR 0 = 1NOT(1) OR NOT(0) = 0 OR 1 = 1NOT(0) OR NOT(0) = 0 OR 0 = 0Therefore we can say the two expressions are equivalent.
Attached the truth table to verify the first De Morgan's law ¬(p ∧ q) ≡ ¬p ∨ ¬q:
What is the explanation of the truth table?As you can see from the attached truth table, the truth values for ¬(p ∧ q) and ¬p ∨ ¬q are the same for all combinations of p and q, confirming the validity of the first De Morgan's law.
De Morgan's law is a fundamental principle in propositional logic.
It states that the negation of a conjunction (AND) is equivalent to the disjunction (OR) of the negations of the individual propositions.
Learn more about truth table at:
https://brainly.com/question/28605215
#SPJ3
______ is not a type of digital signaling technique
Answer:
Data Rate Signaling
An apple, potato, and onion all taste the same if you eat them with your nose plugged
Answer:
I didn't understand your question or is it a fun fact
Flat plate collector can provide temperature upto_____
Answer:
80⁰C
Explanation:
80°C.
Normal flat plate collectors can deliver heat at temperatures up to 80°C. Deficiency rates for normal flat plate collectors can be classified as visual losses, which produce with cumulative angles of the incident sunshine, and thermal losses, which upsurge fast with the working temperature intensities
Question 1 of 8.
What should you do to drive safely in the station?
Turn on your hazard lights
Roll your windows down and turn off the radio
Maintain idle speed (below 5mph)
All of the above
Mark for follow up
Answer: all of the above
Explanation:
To drive safely in the station, the correct option is D. All of the above.
It should be noted that when a person is driving, it's essential for the person to drive carefully in a station.
One should not smoke in a station. Also, it's important that the driver should turn on their hazard lights
Furthermore, it's important for one to roll their windows down, turn off the radio and also maintain idle speed.
In conclusion, the correct option is D.
Read related link on:
https://brainly.com/question/18889428
once scientist has asked a question conducted an investigation and analyzed the data his or hwr goalis to
Answer:
hola
Explanation:
Explanation:
so its an question?..........
I want to explain what 2000 feet looks like to young children so that they can imagine it in class
Answer:
maybe take a really common toy kids play with or often see, find the average height for the toy and do the math to see how many of those toys stacked ontop of eachother would make up 2000 feet. For example (this isn't accurate btw just an idea of what it would sound like but) "Have you ever seen a barbie doll? well if you stack 400 barbie dolls ontop of their head it would be equal to 2000 feet."
Explanation:
sometimes taking common or beloved objects children have into your examples makes them have a better image of how small or how big something is.
Report of invertor to convert 12 volt to 220 volt.
Technician A says that a continuously variable transmission is an automatic transmission that does not shift gears. Technician B says that a continuously variable transmission has a maximum of six distinct gear ranges. Which technician is correct?
Answer:
Only Technician A
Explanation:
Continuously variable transmission (CVT) does not shift gears because it simply doesn't have gears. It instead uses 2 pulleys which change constantly and continuously in size, and they are linked by a belt. Continuously variable transmission (CVT) is automatic transmission as mentioned in the question above, largely due to the power the belt continuously transmits, making the vehicle's engine work in the optimum power range.
While Technician B saying, that a continuously variable transmission has a maximum of six distinct gear ranges, which is not correct because continuously variable transmission (CVT) works with an unlimited number of gear ratios within a fixed range.