The rate of heat energy exhausted to the river is 600.96 MW.
What is efficiency?The ratio of usable output to total input can be used to objectively measure efficiency. The efficiency of the device is defined as the ratio of energy converted to a useable form to the original amount of energy supplied.
Given parameters:
Efficiency of the power plant; η = 31 %
Output electric power; O = 270 MW.
We know that, Efficiency of the power plant;
η = (Output electric power/ input power)× 100%
⇒ input power = (Output electric power × 100)/η
⇒ input power = (270 × 100)/31 MW
= 870.96 MW.
So, the rate of heat energy exhausted to the river that cools the plant = Input power- output power
= (870.96 - 270) MW
= 600.96 MW.
Hence, heat energy exhausted to the river that cools the plant is 600.96 MW.
Learn more about efficiency here:
https://brainly.com/question/14502027
#SPJ1
Find the work done by the force field F in moving an object from A to B. F(x, y) = 6y3/2i + 9x y j A(1, 1), B(3, 4)
Answer:
138
Explanation:
(since there's a blank next to "9x y j", I'm assuming the y of F(x, y) is 9x[tex]\sqrt{y}[/tex] j)
1) find the partial derivative of each:
[tex](6y^{\frac{3}{2} })i + (9x\sqrt{y} )j[/tex]
[tex]f_{x} =(6y^{\frac{3}{2} })_{x} = \int\limits{6y^{\frac{3}{2} }} \, dx = 6xy^{\frac{3}{2} } +c \\\\f_{y} = (9x\sqrt{y} )_{y} = \int\limits{9xy^{\frac{1}{2} } } \, dy = 9x(\frac{2}{3} )y^{\frac{3}{2} } +c = 6xy^{\frac{3}{2} } +c[/tex]
2) use partial integrals to make gradient of f:
take whatever you got from partial integral and add them together (if they repeat, just use it once)
[tex]F =[/tex] Vf (V = gradient of)
[tex]F(x, y) = 6xy^{\frac{3}{2} }[/tex]
3) Evaluate the integrals with given points:
Integral of F dotted with dr = F(point B) - F(point A) = F(3, 4) - F(1, 1)
[tex]F(point B) = 6(3)(4)^{\frac{3}{2} }\\F(Point A) = 6(1)(1)^{\frac{3}{2}}\\F(point B) - F(pointA) = 6(3)(4)^{\frac{3}{2} }-(6(1)(1)^{\frac{3}{2}})[/tex]
= 144 - 6 = 138 units of work
Work done by the force field F in moving an object from A to B = 138 J
Given data :
Force field F(x,y) = [tex]6y^{\frac{3}{2} }i + (9x\sqrt{y} ) j[/tex]
Step 1 : determine the partial derivatives of the vector quantity
Fx = ∫ [tex]6y^{\frac{3}{2} }i = 6xy^{\frac{3}{2} } + c[/tex]
Fy = ∫ [tex](9x \sqrt{y})_{y} = 9x(\frac{2}{3})y^{\frac{3}{2} } + c[/tex]
Equating the partial derivatives :
[tex]9x(\frac{2}{3})y^{\frac{3}{2} } + c[/tex] = [tex]6xy^{\frac{3}{2} } + c[/tex]
therefore the gradient of F i.e. F = vF = F( x,y ) = [tex]6xy^{\frac{3}{2} }[/tex]
Next step : Determine the work done
Work done ( F.dr ) = [ F(point b ) = F( 3,4 ) ] - [ F(point A) = F( 1,1 ) ]
F(3,4 ) = 6(3)(4)[tex]^{\frac{3}{2} }[/tex] = 144
F( 1,1 ) = 6(1)(1)[tex]^{\frac{3}{2} }[/tex] = 6
Therefore the work done by the force field = 144 - 6 = 138 J
Hence we can conclude that the work done by the force field F is = 138 J
Learn more about work done : https://brainly.com/question/21854305
A 27 kg chair initially at rest on a horizontal
floor requires a 173 N horizontal force to set
it in motion. Once the chair is in motion, a
148 N horizontal force keeps it moving at a
constant velocity.
The acceleration of gravity is 9.81 m/s.
a) What is the coefficient of static friction
between the chair and the floor?
Answer:
4653
4565445655687568677667876
9. The acceleration (a)-time (t) graph of a particle moving in a straight line is as shown in figure. At time t = 0, the velocity of particle is 10 m/s. What is the velocity at t = 8 s?
(1) 2 m/s
(2) 4 m/s
(3) 10 m/s
(4) 12 m/s
Answer:Acceleration - time graph for a particle moving in a straight line is as shown in figure. Change in velocity of the particle from t = 0 to t = 6s is:-.
1 answer
·
Top answer:
Change in velocity = (sum of area of graph) = ( 12 × 4 × 4 ) + ( 12 × ( + 2) ( - 1) ) - 4 = 8 - 4 = 4 x
Explanation:
Name two environmental factors, one natural and one human-made, that could account for the trend or pattern in bird (quail, wren) and rodent (mice, rabbits) populations before 1997. Help!
Factors such as more crops, fewer predators, invasive species, and changes in the environment explain a decrease or increase in the birds and rodent populations.
Before 1997, both rodents and birds populations increased due to different factors. Moreover, these factors can be classified as natural or human-made factors. Here are the factors that mainly affected these animals:
Bird population:
Increase:
Decrease in predators that increase birds chances to survive (natural factor)
Increase in crops that improve food access for birds (human factor)
Decrease:
Invasive species or increase of predators (natural factor)
Destruction of natural habitats due to an increase in industry and extraction (human factor)
Rodent population:
Increase:
More adaptability that increased rodents chances to survive (natural factor)Increase in crops that improve food access for rodents (human factor)Decrease:
Invasive species or increase of predators (natural factor)Increase in rabbit consumption and use of rodent control products (human factor)Learn more in: https://brainly.com/question/18123593
9
are things that you can achieve quickly.
O A.
Dreams
OB.
Long-term goals
O c.
Short-term goals
OD.
Plans
Answer:
d
Explanation:
A dreams
.......wkkwkwkwkwkwnwnsksk
Answer:
C. short term goal
Explanation:
took a midterm quiz on canvas, Hope this helps <3
What is friction ???
Answer:
Frictional force is produced when two bodies are rubbed against each other. It is the force that oppose the motion and therefore it stops or slow down a moving body.It depends upon the roughness or smoothness of the surface of the body in contact.Rough surface have more friction that the smooth surface. Similarly, the heavier body produces more friction than a lighter body. Frictional force acts in the opposite direction of the motion of the body.
WILL MARK BRAINLIEST
1. What is the difference between distance and displacement?
A. Distance is measured in feet. Displacement is measured in meters
B. Distance is the difference between how quickly you move between two points. Displacement is the average of that motion
C. Distance is a measure of length of travel. Displacement is the measure of the time it takes to move that length
D. Distance is the length of travel. Displacement is the straight line distance between the starting point and the ending point
2. When forces are in opposite directions, they subtract from one another
A. True
B. False
3. When two forces are in opposite directions, and they are the exact same magnitude, the forces will
A. Subtract from each other
B. Cancel Out
C. Go on Infinitely
D. eventually reach equilibrium
4. Acceleration is a change in motion over time
True or False
Answer:
1. C
2. True
3. D
4. True
Explanation:
While distance refers to “how much land an object has traversed throughout its journey,” displacement measures “how far an object is out of place.” In this post, let's look at the difference between distance and displacement. Thus, option C is correct.
What are the distance and displacement?Displacement and distance are two distinct ideas. The total distance travelled is larger than the displacement between those two points if an object changes direction while travelling.
Distance is the length of any path connecting any two places. Displacement is the straight-line distance between any two points when calculated along the shortest route.
Therefore, The direction is ignored when calculating distance. The direction is accounted for in the displacement calculation.
Learn more about displacement here:
https://brainly.com/question/11934397
#SPJ2
I will mark brainlist
If a wave’s amplitude is 2cm, then its height is equal to:
5 cm.
0 cm
4 cm.
2 cm
Answer:
4 cm
Explanation:
Amplitude is the measure from the MIDLINE to the peak of the wave....so the wave HEIGHT is twice the ampltude
2 x 2 cm = 4 cm
Ryder is testing the change in motion for an object that weighs 25 kg and an object that weighs 30 kg. He will push each object with the same force. Ryder predicts the object that weighs 25 kg will have a greater change in motion. Is this correct?
Yes, the object with the smaller mass will have a greater change in motion.
No, the change in motion for both objects will be the same.
Yes, the mass is greater, and the object will have a greater change of motion.
No, neither of the objects will have a change in motion.
Ryder is testing the change in motion for an object that weighs 25 kg and an object that weighs 30 kg. Then, the greater change in motion is due to the greater mass of the object, and the object will have a greater change of motion. Thus, the correct option is C.
Motion is the phenomenon in which an object changes its position with respect to the time taken. Motion of an object is mathematically described in terms of the displacement covered by the object, the distance, velocity, acceleration, speed and the frame of reference to an observer and measurement of the change in the position of the body of an object relative to that particular frame with the change in time taken.
The motion of an object is proportional to the mass of the object. The mass is greater in this case, and therefore the objects will have a greater change of motion.
Therefore, the correct option is C.
Learn more about Motion here:
https://brainly.com/question/22810476
#SPJ1
What are the two factors that affect the frictional force between objects
Why does the sky appear red and yellow during sunsets.
1. The reds and yellows are caused by the Sun's light having to pass through dust particles near closer to the horizon than when the Sun is higher in the sky.
2. At sunset the prismatic effect of the atmosphere at low angles produces longer red and yellow wavelengths.
3. At sunset blue light is scattered by air molecules at higher altitudes. The longer red and yellow wavelengths must travel further through the atmosphere when the Sun is near the horizon. At some point the reds and yellows finally scatter in the lower atmosphere causing the reds and yellows.
4. The red and yellows are appear at sunset because the light must pass through more atmosphere which slows down the wavelength frequency turning it to slower red and yellow frequencies.
Answer:
The answer should be 3-At sunset blue light is scattered by air molecules at higher altitudes. The longer red and yellow wavelengths must travel further through the atmosphere when the Sun is near the horizon. At some point the reds and yellows finally scatter in the lower atmosphere causing the reds and yellows.
Answer:
3. At sunset blue light is scattered by air molecules at higher altitudes. The longer red and yellow wavelengths must travel further through the atmosphere when the Sun is near the horizon. At some point the reds and yellows finally scatter in the lower atmosphere causing the reds and yellows.
2.(01.01 LC)
Which of the following is true for gravitational force? (3 points)
Decreases with increase in mass
Increases with increase in mass
Increases with increase in distance
Decreases with decrease in distance
Answer:
Increases with increase in mass
Explanation:
gravity is proportional to mass and inversely proportional to the square of the distance between them
F = GMm/d²
PLEASE HELP ME GET THIS RIGHT
Explanation:
I'm not sure, but I would go for the more than A since its orbital speed is at its fastest and the sweep occurs in about the same period of days.
Which of the following best describes an achievement test that is given at the end of a learning segment to evaluate mastery of objectives?
Answer
An Achievement test is an assessment of developed knowledge or skill. ... Achievement tests are developed to measure skills and knowledge learned in a given grade level, usually through planned instruction, such as training or classroom instruction. Achievement tests are often contrasted with aptitude tests.
Explanation:
what is translator disadvantage?
Machine translators:
Level of accuracy can be very low.
Accuracy is also very inconsistent across different languages.
Machines can't translate context.
Mistakes are sometimes costly.
Sometimes translation simply doesn't work.
Human translators:
Turnaround time is longer.
Translators rarely work for free.
Unless you use a translation agency, with access to thousands of translators, you're limited to the languages any one translator can work with.
Please write a paragraph explaining the bible verse below in your own words.
Exodus 16:19-20
Answer:
Moses had told them to not keep the food till morning but some kept some anyways because they probably thought they were going to starve or not have food the next morning but what I think it means is that you have to trust in God that he will provide for you and so when the people kept the food cuz he thought they were probably going to start of the next day it got maggots
What happened when a lobster release a claw? a. The lobster attacks with the claw. b. The lobster let the claw go. C. The lobster bites off the claw. D. The lobster eats with the claw.
Answer:b
Explanation:
Answer:
The lobster let the claw go. so, B.
Explanation:
i hope this helps.
which of the following statements describes a perfectly inelastic collision
Answer: An ice hockey player picks up a trophy as he slides past it.
Two pool balls colliding precisely inelastically and rebounding off one another is an example. So, the correct option is A.
What is an Inelastic collision?Inelastic collisions are those in which the total kinetic energy is lower after the impact than it was before. The stick is travelling quickly in the direction of the ball before to the contact. The stick comes to a stop following the accident. It transfers some of its kinetic energy to the cue ball, which rolls forward.
The type of collision mentioned in the given example is known as an inelastic collision is one in which the system's momentum is preserved but its kinetic energy is not. In a ballistic pendulum, an example of an inelastic collision. Dropped ball of clay is another illustration of an inelastic collision.
Thus, the correct option is A.
Learn more about Inelastic collision, here:
https://brainly.com/question/15742157
#SPJ7
Your question is incomplete, most probably the complete question is:
Which of the following statements describes a perfectly inelastic collision?
A. Two billiard balls bounce off of each other,
B. A car crashes into a tree and rebounds in the other direction,
C. A wad of chewing gum is thrown and sticks to a moving truck,
D. Two ice skaters hit each other and fall over in opposite directions,
If work stays the same and the distance is increased, then less force is needed to do the work.
True
False
Answer:
False
Explanation:
This is because the work is the same so the force won't change
The force of earth’s gravity is 10N downward. What us the acceleration of a 15kg backpack if lifted with a a 15N force?
Answer:
F-F(gr) = ma
a= {F-F(gr)}/m =
=(15-10)/15=0.33 m/s² (upward)
Which event provides evidence that matter can reflect waves?
A. A dog's bark is barely heard through double-pane windows.
B. A bat finds a moth using echolocation.
C. A whale's song is heard hundreds of miles away,
D. A fish appears to be farther from a boat than it is.
Answer:
B. A bat finds a moth using echolocation
Explanation:
100% i just took that test today
On clear day, sunlight delivers approximately 1000 J each second to a 1 m2 surface; smaller areas receive proportionally less--half the area receives half the energy. A 12% efficient solar cell, a square 12 cm on a side, is in bright sunlight.
How much electric power does it produce?
The direct proportions rule allows to find the result for the energy produced by a solar cell is:
E = 1,728 J
The efficiency of a solar cell is the percentage of incident energy that transforms into electricity.
The direct proportions rule or three rule stable that if two quantities are proportional the product remains constant.
They indicate that the length of the solar cell is l = 12 cm = 0.12m. Let's find the area of the solar cell.
A = l²
A = 0.12²
A = 1.44 10⁻² m²
Let's use a direct proportion rule. If 1 m² receives 1000J of energy, how much does an area of 1.44 10⁻² m² receive?
Energy_cell = 1000 J ( [tex]\frac{1.44 \ 10^{-2}}{1}[/tex] )
Energy_ cell = 14.4 J
Let's use another direct ratio rule for efficiency.
[tex]Energy_{produced} = Energy_{cell} \frac{12}{100} \\Energy_{produced} = 14.4 0.12 \\Energy_{produced} = 1.728 J[/tex]
In conclusion using the direct proportions rule we can find the result for the energy produced by a solar cell is:
E = 1,728 J
Learn more here: https://brainly.com/question/11918400
Over half the global population faces a shortage of clean water. Which example is a point source water pollutant? pesticide run-off from farmers’ fields a sewer pipe draining directly into a river road oil washing into sewer drains, and eventually reaching waterways erosion from a denuded slope after a heavy rainfall
An example of a point source water pollutant is a sewer pipe draining directly into a river.
According to the United States Environmental Protection Agency, a point source pollution is defined as; “any single identifiable source of pollution from which pollutants are discharged, such as a pipe, ditch, ship or factory smokestack.”
Hence, an example of a point source water pollutant is a sewer pipe draining directly into a river. The pollution is coming from an easily identifiable source which is a sewer pipe connected to a river directly.
Learn more: https://brainly.com/question/17638582
A magnet is located above circular current. What is the direction of the magnetic force on the magnet
The magnet is attracted to the ring since the north pole of the current loop is above the ring and the south pole is below the ring.
Croquet ball A moving at 8.3 m/s makes a head on collision with ball B of equal mass and initially at rest. Immediately after the collision ball B moves forward at 6.4 m/s .
What fraction of the initial kinetic energy is lost in the collision?
Answer:
0.25
Explanation:
That is the right answer.
The fraction of the initial kinetic energy is lost in the collision is 35.3%.
The given parameters:
Initial velocity of ball A = 8.3 m/sInitial velocity of ball B = 0Final velocity of ball B = 6.4 m/sThe initial kinetic energy of the system collision is calculated as follows;
[tex]K.E_i = \frac{1}{2} mv_1_i^2 + \frac{1}{2} mv_2_i^2\\\\K.E_i = \frac{1}{2} (m)(8.3)^2 + \frac{1}{2} (m) (0)^2\\\\K.E_i = 34.445 m[/tex]
The final velocity of ball A after collision is calculated as follows;
[tex]u_1 + v_1 = u_2 + v_2\\\\8.3 + v_1 = 0 + 6.4\\\\v_1 = 6.4 - 8.3\\\\v_1 = -1.9 \ m/s[/tex]
The final kinetic energy of the system after collision is calculated as follows;
[tex]K.E_f = \frac{1}{2} m(-1.9)^2 + \frac{1}{2} m(6.4)^2\\\\K.E_f = 22.285 \ m \[/tex]
The fraction of the initial kinetic energy is lost in the collision is calculated as follows;
[tex]= \frac{K_i - K_f}{K_i} \\\\= \frac{34.445 - 22.285}{34.445} \\\\= 0.353\\\\= 35.3\%[/tex]
Learn more about kinetic energy of elastic collision here: https://brainly.com/question/7694106
Example 4.16
An object of mass 3 kg rests on a plane. The coefficient of static friction and that of kinein
friction are given by Hs = 0.3 and pk = 0.2.
The plane is inclined at angle o to the horizontal.
(i) Find the maximum value of 0 for which the object remains at rest on the plane.
(ii) Find the acceleration of the object if it started sliding from rest down the plane at
angle Omax to the horizontal.
(ii) How long does it take the object to move, from rest, a distance of Imetre under the
conditions of (ii).
Answer:
Explanation:
(i) μs = F/N = mgsinθ/mgcosθ = tanθ
tanθ = 0.3
θ = 16.7°
(ii) a = F/m
a = (mgsinθ - (μk)mgcosθ) / m
a = g(sinθ - (μk)cosθ)
a = 9.8(sin16.7 - (0.2)cos16.7)
a = 0.94 m/s²
(iii) s = ½at²
t = √(2s/a)
t = √(2(1)/0.94)
t = 1.5 s
Question 3 of 20 :
Select the best answer for the question.
3. Which of the following accurately describes the behavior of water when subjected to
temperature change?
A. The volume of water will decrease if heated from 6°C to 7°C.
B. The volume of water will increase if cooled from 3°C to 2°C.
O C. A mass of water will contract if cooled from 1°C to 0°C.
D. A mass of water will expand if heated from 0°C to 2°C.
As water cools the volume expands.
Answer: B. The volume of water will increase if cooled from 3°C to 2°C.
HIHIHHHHHHHHIHIHIIHIHHHHIHIHIHIHIHIHIHIHIHIHIHIHIHIIH
Answer:
Ok thanks for the points though
Explanation:
The Greek root astro means "stars." Use the context clues to choose the correct definition of the word astronomer. According to the astronomer, the bigger the telescope, the more detail we can see in the images. O A. a person who studies astronauts O B. a person who studies the stars O C. a person who tells the future O D. a person who studies other people
Answer:
b, it's a pretty easy explanation
Calculate the torque produced by a 50.0 N perpendicular force at the end of a 0.300 m long wrench.
Answer:
Torque = 50N x 0.3m = 15Nm
Explanation:
Torque = Force x length of lever arm. To obtain the torque simply multiply the two given values.
