Answer:
a) θ = 14.23º, b) θ₂ = 75.77, c) t = 0.6019 s
Explanation:
This is a missile throwing exercise.
a) the reach of the ball is the distance traveled for the same departure height
R = [tex]\frac{v_o^2 \ sin 2 \theta }{g}[/tex]
sin 2θ = [tex]\frac{Rg}{v_o^2}[/tex]
sin 2θ = 7.00 9.8 / 12.0²
2θ = sin⁻¹ (0.476389) = 28.45º
θ = 14.23º
the complementary angle that gives the same range is the angle after 45 that the same value is missing to reach 90º
θ ’= 90 -14.23
θ’= 75.77º
b) the two angles that give the same range are
θ₁ = 14.23
θ₂ = 75.77
the greater angle has a much greater height so the time of the movement is greater and has a greater chance of being intercepted by the other team.
C) the time of the pass can be calculated with the expression
x = v₀ₓ t
t = x / v₀ₓ
t = 7 / 11.63
t = 0.6019 s
A projectile is fired into the air from the top of a 200-m cliff above a valley as shown below. Its initial velocity is 60 m/s at 60° above the horizontal. Calculate (a) the maximum height, (b) the time required to reach its highest point, (c) the total time of flight, (d) the components of its velocity just before striking the ground, and (e) the horizontal distance traveled from the base of the cliff.
a) y(max) = 337.76 m
b) t₁ = 5.30 s the time for y maximum
c)t₂ = 13.60 s time for y = 0 time when the fly finish
d) vₓ = 30 m/s vy = - 81.32 m/s
e)x = 408 m
Equations for projectile motion:
v₀ₓ = v₀ * cosα v₀ₓ = 60*(1/2) v₀ₓ = 30 m/s ( constant )
v₀y = v₀ * sinα v₀y = 60*(√3/2) v₀y = 30*√3 m/s
a) Maximum height:
The following equation describes the motion in y coordinates
y = y₀ + v₀y*t - (1/2)*g*t² (1)
To find h(max), we need to calculate t₁ ( time for h maximum)
we take derivative on both sides of the equation
dy/dt = v₀y - g*t
dy/dt = 0 v₀y - g*t₁ = 0 t₁ = v₀y/g
v₀y = 60*sin60° = 60*√3/2 = 30*√3
g = 9.8 m/s²
t₁ = 5.30 s the time for y maximum
And y maximum is obtained from the substitution of t₁ in equation (1)
y (max) = 200 + 30*√3 * (5.30) - (1/2)*9.8*(5.3)²
y (max) = 200 + 275.40 - 137.64
y(max) = 337.76 m
Total time of flying (t₂) is when coordinate y = 0
y = 0 = y₀ + v₀y*t₂ - (1/2)* g*t₂²
0 = 200 + 30*√3*t₂ - 4.9*t₂² 4.9 t₂² - 51.96*t₂ - 200 = 0
The above equation is a second-degree equation, solving for t₂
t = [51.96 ±√ (51.96)² + 4*4.9*200]/9.8
t = [51.96 ±√2700 + 3920]/9.8
t = [51.96 ± 81.36]/9.8
t = 51.96 - 81.36)/9.8 we dismiss this solution ( negative time)
t₂ = 13.60 s time for y = 0 time when the fly finish
The components of the velocity just before striking the ground are:
vₓ = v₀ *cos60° vₓ = 30 m/s as we said before v₀ₓ is constant
vy = v₀y - g *t vy = 30*√3 - 9.8 * (13.60)
vy = 51.96 - 133.28 vy = - 81.32 m/s
The sign minus means that vy change direction
Finally the horizontal distance is:
x = vₓ * t
x = 30 * 13.60 m
x = 408 m
A 1050 kg car accelerates from 11.3 m/s to 26.2 m/s . What impulse does the engine give?
Answer:
I = 15,645. kg*m/s or 15,645 N*s
Explanation:
I = m(^v)
I = 1050kg((26.2m/s-11.3m/s)
I = 15,645. kg*m/s
If a proton and electron both move through the same displacement in an electric field, is the change in potential energy associated with the proton equal in magnitude and opposite in sign to the change in potential energy associated with the electron?
a. The magnitude of the change is smaller for the proton.
b. The magnitude of the change is larger for the proton.
c. The signs Of the two changes in potential energy are opposite.
d. They are equal in magnitude.
e. The signs of the two changes in potential energy are the same.
Answer: They are equal in magnitude.
- The signs of the two changes in potential energy are opposite
Explanation:
When the proton and electron both move through the same displacement in an electric field, the change in potential energy that is associated with the proton is equal in magnitude.
Also, it should be noted that the signs of the two changes in potential energy are opposite.
trong cùng một nhiệt độ, lượng năng lượng trên mỗi mol của chất khí nào lớn nhất
a) Khí đơn nguyên tử
b) Khí có từ ba nguyên tử
c) Khí lưỡng nguyên tử
A parallel-plate capacitor consists of two plates, each with an area of 29 cm2cm2 separated by 3.0 mmmm. The charge on the capacitor is 7.8 nCnC . A proton is released from rest next to the positive plate. Part A How long does it take for the proton to reach the negative plate
Answer:
t = 2.09 10⁻³ s
Explanation:
We must solve this problem in parts, first we look for the acceleration of the electron and then the time to travel the distance
let's start with Newton's second law
∑ F = m a
the force is electric
F = q E
we substitute
q E = m a
a = [tex]\frac{q}{m} \ E[/tex]
a = [tex]\frac{1.6 \ 10^{-19}}{ 9.1 \ 10^{-31} } \ 7.8 \ 10^{-9}[/tex]
a = 1.37 10³ m / s²
now we can use kinematics
x = v₀ t + ½ a t²
indicate that rest starts v₀ = 0
x = 0 + ½ a t²
t = [tex]\sqrt{\frac{2x}{a} }[/tex]
t = [tex]\sqrt{\frac {2 \ 3 \ 10^{-3}}{ 1.37 \ 10^3} }[/tex]
t = 2.09 10⁻³ s
A plastic dowel has a Young's Modulus of 1.50 ✕ 1010 N/m2. Assume the dowel will break if more than 1.50 ✕ 108 N/m2 is exerted. What is the maximum force (in kN) that can be applied to the dowel assuming a diameter of 2.30 cm?
A.
52.3 kN
B.
62.3 kN
C.
72.3 kN
D.
42.3 N
Answer:
cobina
Explanation:
me 2
For example, we can take Water
In (A) Water has same mass and great volume
In (B) Water has same mass and lower volume
Will there be any change in its density then?
Answer:
yes there will be change in its density
A mass is tired to spring and begins vibration periodically the distance between it's lowest position is 48cm what is the Amplitude of the vibration
Answer:
The amplitude of vibration of the spring is "24 cm"
The periodic vibrating body's motion follows a sinusoidal path. This sinusoidal path is illustrated in the attached picture.
From the picture, it can be clearly seen that the amplitude of the periodic vibration motion is the distance from its mean position to the highest point.
Since the distance of both the highest and the lowest points from the mean position is the same. Therefore, the distance between the lowest and the highest point must be equal to two times the amplitude of the wave.
Amplitude = 24 cm
Rays of light coming from the sun (a very distant object) are near and parallel to the principal axis of a concave mirror. After reflecting from the mirror, where will the rays cross each other at a single point?
The rays __________
a. will not cross each other after reflecting from a concave mirror.
b. will cross at the center of curvature.
c. will cross at the point where the principal axis intersects the mirror.
d. will cross at the focal point. will cross at a point beyond the center of curvature.
A concave mirror is an example of curved mirrors. So that the appropriate answer to the given question is option D. The rays will cross at the focal point.
A concave mirror is a type of mirror in which its inner part is the reflecting surface, while its outer part is the back of the mirror. This mirror reflects all parallel rays close to the principal axis to a point of convergence. It can also be referred to as the converging mirror.
In this type of mirror, all rays of light parallel to the principal axis of the mirror after reflection will cross at the focal point.
Therefore, the required answer to the given question is option D. i.e The rays will cross at the focal point.
For reference: https://brainly.com/question/20380620
A car is traveling at 118 km/h when the driver sees an accident 85 m ahead and slams on the brakes. What minimum constant deceleration is required to stop the car in time to avoid a pileup
Answer:
The constant minimum deceleration required to stop the car in time to avoid pileup is 6.32 m/s²
Explanation:
From the question, the car is traveling at 118 km/h, that is the initial velocity, u = 118km/h
The distance between the car and the accident at the moment when the driver sees the accident is 85 m, that is s = 85 ,
Since the driver slams on the brakes and the car will come to a stop, then the final velocity, v = 0 km/h = 0 m/s
First, convert 118 km/h to m/s
118 km/h = (118 × 1000) /3600 = 32.7778 m/s
∴ u = 32.7778 m/s
Now, to determine the deceleration, a, required to stop,
From one of the equations of motion for linear motion,
v² = u² + 2as
Then
0² = (32.7778)² + 2×a×85
0 = 1074.3841 + 170a
∴ 170a = - 1074.3841
a = - 1074.3841 / 170
a = - 6.3199
a ≅ - 6.32 m/s²
Hence, the constant minimum deceleration required to stop the car in time to avoid pileup is 6.32 m/s²
The temperature of a body falls from 30°C to 20°C in 5 minutes. The air
temperature is 13°C. Find the temperature after a further 5 minutes.
Answer:
15.88
is the correct answer
An object of mass 80 kg is released from rest from a boat into the water and allowed to sink. While gravity is pulling the object down, a buoyancy force of 1/50 times the weight of the object is pushing the object up (weight=mg). If we assume that water resistance exerts a force on the abject that is proportional to the velocity of the object, with proportionality constant 10 N-sec/m, find the equation of motion of the object. After how many seconds will the velocity of the object be 40 m/s? Assume that the acceleration due to gravity is 9.81 m/sec^2.
Answer:
a) Fnet = mg - Fb - Fr
b) 8.67 secs
Explanation:
mass of object = 80 kg
Buoyancy force = 1/50 * weight ( 80 * 9.81 ) = 15.696
Proportionality constant = 10 N-sec/m
a) Calculate equation of motion of the object
Force of resistance on object due to water = Fr ∝ V
= Fr = Kv = 10 V
Given that : Fb( due to buoyancy ) , Fr ( Force of resistance ) acts in the positive y-direction on the object while mg ( weight ) acts in the negative y - direction on the object.
Fnet = mg - Fb - Fr
∴ Equation of motion of the object ( Ma = mg - Fb - Fr )
b) Calculate how long before velocity of the object hits 40 m/s
Ma = mg - Fb - Fr
a = 9.81 - 0.1962 - 0.125 V = 9.6138 - 0.125 V
V = u + at ---- ( 1 )
u = 0
V = 40 m/s
a = 9.6138 - 0.125 V
back to equation 1
40 = 0 + ( 9.6138 - 0.125 (40) ) t
40 = 4.6138 t
∴ t = 40 / 4.6138 = 8.67 secs
Describe sound and record
Answer:
record is information created, received and maintained as evidence and information by an organization or person.in simpler terms it's a collection of of fields probably of different data types.
sound is however something loud or soft.which can be defined as vibrations that travel through the air or another medium.
I hope this helps
A diffraction grating has 6000 lines per centimeter ruled on it. What is the angular separation (in degrees) between the second and the third orders on the same side of the central bright fringe when the grating is illuminated with a beam of light of wavelength 500 nm
Explanation:
Hope it Will help he hsuejwoamxgehanwpalasmbwfwfqoqlmdbehendalmZbgevzuxwllw. yeh we pabdvddxhspapalw. X
The angular separation (in degrees) between the second and the third orders on the same side of the central bright fringe if the wavelength is 500 nm and A diffraction grating has 6000 lines per centimeter ruled on it, is 27.29°.
What is diffraction?Waves spreading outward around obstructions are known as diffraction. Sound, electromagnetic radiation like light, X-rays, and gamma rays, as well as very small moving particles like atoms, neutrons, and electrons that exhibit wavelike qualities all exhibit diffraction.
Given:
The number of lines = 6000 per cm,
The Wavelength, λ = 500 nm = 500 × 10 ⁻⁹ m
Calculate the diffraction grating,
[tex]d = 1 / no\ of\ lines[/tex]
d = 10⁻² / 6000 m,
Calculate the second-order maxima angle and third-order maxima angle by the formula given below,
[tex]dsin\theta_1 = n_1 \lambda[/tex]
[tex]sin\theta_1 = n_1\lambda / d[/tex]
[tex]\theta _1 = sin^{-1}[2\times 500\times 10 ^{-9}/10^{-2}\times 6000][/tex]
θ₁ = sin⁻¹(0.6)
θ₁ = 36.87°
Similarly, for θ₂,
θ₂ = sin⁻¹(3 × 500 × 10 ⁻⁹ / 10⁻² × 6000)
θ₂ = sin⁻¹(0.9)
θ₂ = 64.16°
Calculate the separation as follows,
θ₂ - θ₁ = 64.16° - 36.87°
θ₂ - θ₁ = 27.29°
Therefore, the angular separation (in degrees) between the second and the third orders on the same side of the central bright fringe if the wavelength is 500 nm and A diffraction grating has 6000 lines per centimeter ruled on it, is 27.29°.
To know more about diffraction:
https://brainly.com/question/12290582
#SPJ2
a volcano that may erupt again at some time in the distant future is
The voltage in an EBW operation is 45 kV. The beam current is 50 milliamp. The electron beam is focused on a circular area that is 0.50 mm in diameter. The heat transfer factor is 0.87. Calculate the average power density in the area in watt/mm2.
Answer:
[tex]P_d=6203.223062W/mm^2[/tex]
Explanation:
From the question we are told that:
Voltage [tex]V=45kV[/tex]
Current [tex]I=50mAmp[/tex]
Diameter [tex]d=0.50mm[/tex]
Heat transfer factor [tex]\mu= 0.87.[/tex]
Generally the equation for Power developed is mathematically given by
[tex]P=VI\\\\P=45*10^3*50*10^{-3}[/tex]
[tex]P=2.250[/tex]
Therefore
Power in area
[tex]P_a=1400*0.87[/tex]
[tex]P_a=1218watt[/tex]
Power Density
[tex]P_d=\frac{P_a}{Area}[/tex]
[tex]P_d=\frac{1218}{\pi(0.5^2/4)}[/tex]
[tex]P_d=6203.223062W/mm^2[/tex]
herical piece of candy is suspended in flowing water. The candy has a density of 1950 kg/m3 and has a 1.0 cm diameter. The water velocity is 1.0 m/s, the water density is assumed to be 1000.0 kg/m3, and the water viscosity is 1.010-3 kg/m/s. The diffusion coefficient of the candy solute in water is 2.010-9 m2/s, and the solubility of the candy solute in water is 2.0 kg/m3. Calculate the mass tran
Answer: Below is the complete question
A spherical piece of candy is suspended in flowing water. The candy has a density of 1950 kg/m3 and has a 1.0 cm diameter. The water velocity is 1.0 m/s, the water density is assumed to be 1000.0 kg/m3, and the water viscosity is 1.0x10-3 kg/m/s. The diffusion coefficient of the candy solute in water is 2.0x10-9 m2/s, and the solubility of the candy solute in water is 2.0 kg/m3. Calculate the mass transfer coefficient (m/s)
answer:
mass transfer coefficient = 9.56 * 10^-5 m/s
Explanation:
Candy density = 1950 kg/m^3
Candy diameter = 1 cm
Velocity of water = 1 m/s
water density = 1000 kg/m^3
Viscosity of water = 1 * 10^-3 kg/m/s
diffusion coefficient of candy in water = 2 * 10^-9 m^2/s
solubility of candy = 2 kg/m^3
Determine the mass transfer coefficient ( m/s )
( Sh) mass transfer coefficient ( flow across sphere ) = 2 + 0.6Re^1/2 * SC^1/3
where : Re = vdp / μ , Sh = KLd / Deff
attached below is the remaining solution .
mass transfer coefficient = 9.56 * 10^-5 m/s
A refrigerator has a coefficient of performance equal to 4.00. The refrigerator takes in 110 J of energy from a cold reservoir in each cycle. (a) Find the work required in each cycle. J (b) Find the energy expelled to the hot reservoir. J
Answer:
The correct answer is:
(a) 27.5 Joules
(b) 141.5 Joules
Explanation:
Given:
Energy,
[tex]Q_c = 110 \ J[/tex]
Coefficient of performance refrigerator,
[tex]Cop(refrig)=4[/tex]
(a)
As we know,
⇒ [tex]Cop(refrig) = \frac{Q_c}{Work}[/tex]
or,
⇒ [tex]Work=\frac{Q_c}{Cop(refrig)}[/tex]
[tex]=\frac{110}{4}[/tex]
[tex]=27.5 \ Joules[/tex]
(b)
⇒ [tex]Heat \ expelled = Heat \ removed +Work \ done[/tex]
or,
⇒ [tex]Q_h = Q_c+Work[/tex]
[tex]=114+27.5[/tex]
[tex]=141.5 \ Joules[/tex]
: A fan is placed on a horizontal track and given a slight push toward an end stop 1.80 meters away. Immediately after the push, the fan of the cart engages and slows the cart with an acceleration of -0.45 m/s2. What is the maximum possible velocity (magnitude) the cart can have after the push so that the cart turns around just before it hits the end-stop
Answer:
The initial velocity is 1.27 m/s.
Explanation:
distance, s = 1.8 m
acceleration, a = - 0.45 m/s^2
final velocity, v = 0
let the initial velocity is u.
Use third equation of motion
[tex]v^2 = u^2 + 2 a s \\\\0 = u^2 - 2 \times 0.45\times 1.8\\\\u = 1.27 m/s[/tex]
We have that the Initial velocity is mathematically given as
u=1.27m/s
Maximum possible velocity
Question Parameters:
a slight push toward an end stop 1.80 meters away
he fan of the cart engages and slows the cart with an acceleration of -0.45 m/s2
Generally the equation for the third equation of motion is mathematically given as
Vf^2 = Vi^2 + 2ad
Therefore
0=u^2+0.45*1.8
u=1.27m/s
For more information on velocity visit
https://brainly.com/question/17617636
An ink-jet printer steers charged ink drops vertically. Each drop of ink has a mass of 10-11 kg, and a charge due to 500,000 extra electrons. It goes through two electrodes that gives a vertical acceleration of 104 m/s2. The deflecting electric field is _____ MV/m.
Answer:
E = 1.25 MV / m
Explanation:
For this exercise let's use Newton's second law
F = m a
where the force is electric
F = q E
we substitute
q E = m a
E = m a / q
indicate there are 500,000 excess electrons
q = 500000 e
q = 500000 1.6 10⁻¹⁹
q = 8 10⁻¹⁴ C
the mass is m = 10⁻¹¹ kg and the acceleration a = 10⁴ m / s²
let's calculate
E = 10⁻¹¹ 10⁴ / 8 10⁻¹⁴
E = 0.125 10⁷ V / m = 1.25 10⁶ V / m
E = 1.25 MV / m
A circular parallel-plate capacitor whose plates have a radius of 25 cm is being charged with a current of 1.3 A. What is the magnetic field 11 cm from the center of the plates
The magnetic field at 11 cm from the center of the plates is 2.364 x 10⁻⁷ T.
Given;
radius of the circular plate, d = 25 cm = 0.25 m
current in the plate, I = 1.3 A
distance from the center of the circular plate, r = 11 cm = 0.11 m
To find:
magnetic field (B)The magnetic field from the given distance is calculated as from Biot Savart equation:
[tex]B = \frac{\mu_o I}{2\pi r} \\\\where;\\\\\mu_o \ is \ permeability \ of \ free \ space \ 4\pi \times 10^{-7} \ T.m/A\\\\B = \frac{(4\pi \times 10^{-7} ) \times (1.3)}{2\pi \times 0.11} \\\\B = 2.364 \ \times 10^{-6} \ T[/tex]
Therefore, the magnetic field 11 cm from the center of the plates is 2.364 x 10⁻⁷ T.
Learn more here: https://brainly.com/question/17035710
Vector a has a magnitude of 8 and makes an angle of 45 with positive x axis vector B has also the same magnitude of 8 units and direction along the
Answer:
prove that Sin^6 ϴ-cos^6ϴ=(2Sin^2ϴ-1)(cos^2ϴ+sin^4ϴ)
please sove step by step with language it is opt maths question
May someone help...please. Pretty please...
If a person is 18 % shorter than average, what is the ratio of his walking pace (that is, the frequency 'f' of his motion) to the walking pace of a person of average height? Assume that a person's leg swings like a pendulum and that the angular amplitude of everybody's stride is about the same.
f(short)/f(avg)=?
We have that the ratio of his walking pace to the walking pace of a person of average height is
[tex]\frac{V_2}{V_1}=1.10[/tex]
given the assumption and the calculation given below
From the question we are told that:
Consider a person 18\% shorter than average
Let average height of a person be [tex]10m[/tex]
Therefore
The height of an [tex]18\%[/tex] shorter man is mathematically given as
H=10*0.18
H=8.2m
Generally, the equation for velocity is mathematically given by
[tex]v=\frac{1}{2\pi} \sqrt{{g}{l}}[/tex]
Where we have the Assumption that a person's leg swings like a pendulum and that the angular amplitude of everybody's stride is about the same
Therefore
[tex]\frac{V_1}{V_2}=\frac{l_1}{l_2}[/tex]
[tex]\frac{V_1}{V_2}={82}{100}[/tex]
[tex]\frac{V_2}{V_1}=1.10[/tex]
In conclusion
The ratio of his walking pace (that is, the frequency 'f' of his motion) to the walking pace of a person of average height is
[tex]\frac{V_2}{V_1}=1.10[/tex]
For more information on this visit
https://brainly.com/question/21196186
what is the major difference between the natural frequency and the damped frequency of oscillation.
Answer:
This causes the amplitude of the oscillation to decay over time. The damped oscillation frequency does not equal the natural frequency. Damping causes the frequency of the damped oscillation to be slightly less than the natural frequency
1 A thing ring has a mass of 6kg and a radius of 20cm. calculate the rotational inertia.
Answer:
2400kgm²
Explanation:
Rotational inertia=mass x radius²
HELP ME PLZ FAST
There is more than 1 answer,
The picture is down
Answer:
test her prototype and collect data about its flight
A painter sets up a uniform plank so that he can paint a high wall. The plank is 2 m long and weighs 400 N. The two supports holding up the plank are placed 0.2 m from either end. Show that the upwards force on each of the planks is 200 N. Draw a sketch.
The upward force on each supporting plank is 200 N
The given parameters include;
weight of the plank, W₁ = 400 Nlength of the plank, l = 2 mupward force of each supporting plank, = W₂ and W₃To show that the upward force of each supporting plank is 200 N, make the following sketch.
W₂ W₃
↑ ↑
-----------------------------------------------------------------------
0.2m ↓ 0.2m
400 N
The two supporting planks keeps the 2m plank in equilibrium position. If the plank is in equilibrium position the sum of the upward forces equals sum of the downward force.W₂ + W₃ = 400 N
But the distance of each supporting plank from the end is equal, (0.2m).
Then, W₂ = W₃
2W₂ = 400 N
W₂ = 400N/2
W₂ = 200 N
W₃ = 200 N
Therefore, the upward force on each supporting plank that keeps the plank in equilibrium position is 200 N.
To learn more about equilibrium forces visit: https://brainly.com/question/12582625
When a charged particle moves at an angle of 26.1 with respect to a magnetic field, it experiences a magnetic force of magnitude F. At what angle (less than 90o) with respect to this field will this particle, moving at the same speed?
Answer:
The angle is 153.9 degree.
Explanation:
Let the magnetic field is B and the charge is q. Angle = 26.1 degree
The force is F.
Let the angle is A'.
Now equate the magnetic forces
[tex]q v B sin 26.1 = q v B sin A'\\\\A' = 180 - 26.1 = 153.9[/tex]
A cylinder is given a push and then rolls up an inclined plane. If the origin is the starting point, sketch the position, velocity, and acceleration of the cylinder vs. time as it goes up and then down the plane.
Vặt nhỏ được ném lên từ điểm A trên mặt đất với vận tốc đầu 20m/s theo phương thẳng đứng. Xác định độ cao của điểm O mà vật đạt được. Bỏ qua ma sát
Explanation:
mặt đất với vận tốc ban đầu 20m/s. Bỏ qua mọi ma sát, lấy g = 10 m/s2. Độ cao cực đại mà vật đạt được là.
