Answer:
5.25 m/s to the east
Explanation:
Applying,
MV = mv.............. Equation 1
Where M = mass of the launcher, V = recoil velocity of the launcher, m = mass of the balloon, v = velocity of the balloon
make V the subject of the equation
V = mv/M............ Equation 2
From the question,
M = 2 kg, m = 0.75 kg, v = 14 m/s
Substitute these values into equation 2
V = (0.75×14)/2
V = 5.25 m/s to the east
Think about a thermos bottle. It consists of an inner bottle with a shiny silver surface separated from an outer container by a space with no air. In what ways does it block conduction, convection, and radiation?
Answer:
Radiation
Explanation:
Conduction, convection and radiation are the three modes of heat transfer.
1. Conduction: When the one end is heated of any rod, the heat transfer to the other end by the vibrational motion of the molecules, it is called conduction.
The heat transfer in a solid is due to the conduction.
2. Convection: When the liquid or gas is heated, the molecules which is in contact to the heat, heated first and due to the decrease in density they moves up and the molecules on the upper side are higher in density so they moves down. These are called convection currents. The process continues till the entire liquid becomes heated. It generally takes place in liquids and gases.
3. Radiation: The process of heat transfer in which no molecules takes place is called radiation. The heat coming from sun is due to the radiation. It does not require any medium.
In the thermos bottle, as there is no air between the two layers, so the heat transfer is due to the radiation.
The following contribute to accidents when a teen driver has other teens as passengers
Answer:
When a teen driver drives with a lot of his peers as passengers they may lead to distraction which may later end up in accident as the driver was distracted
Overconfidence, lack of focus, and phone while driving are the factors contribute to accidents when a teen driver controls other teens as passengers,
What are the factors contribute to accidents when a teen driver has other teens as passengers?When a teen driver drives with a lot of his peers as passengers they may direct to distraction which may later end up in casualty as the driver was distracted.
Several studies have indicated that passengers substantially increase the chance of crashes for young, novice drivers. This improved risk may result from distractions that young passengers complete for drivers.Teens driving with a teen or young adult passengers existence of teen or young adult passengers raises the crash risk of unsupervised teen drivers. This risk grows with each additional teen or a young adult passenger.
Crash risk is two- to six times more significant for those who utilize a cellphone while driving resembled for drivers who are not distracted. Using a phone delays reaction time increases lane deviations, and forces drivers to look away from the road for extended times.
Overconfidence, lack of focus, and phone while driving are the factors contribute to accidents when a teen driver controls other teens as passengers,
To learn more about factors contribute to accidents refer to:
https://brainly.com/question/4853141
#SPJ2
When an automobile moves with constant velocity the power developed is used to overcome the frictional forces exerted by the air and the road. If the power developed in an engine is 50.0 hp, what total frictional force acts on the car at 55 mph (24.6 m/s)
P = F v
where P is power, F is the magnitude of force, and v is speed. So
50.0 hp = 37,280 W = F (24.6 m/s)
==> F = (37,280 W) / (24.6 m/s) ≈ 1520 N
TIME REMAINING
45:43
What are possible units for impulse? Check all that apply.
kg • m
kg • meters per second
N • s
N • m
StartFraction Newtons times meters per second EndFraction
Answer:
n.m maby
Explanation:
i think or its kg m/s
Answer:
answer (B) & (C)
Explanation:
kg • /N • s
Physical quantities expresed only by their magnitude is
Answer:
Scalar quantity is the Physical quantity expresed only by their magnitude.
The cavity within a copper [β = 51 × 10-6 (C°)-1] sphere has a volume of 1.180 × 10-3 m3. Into this cavity is placed 1.100 × 10-3 m3 of benzene [β = 1240 × 10-6 (C°)-1]. Both the copper and the benzene have the same temperature. By what amount ΔT should the temperature of the sphere and the benzene within it be increased, so that the liquid just begins to spill out?
Answer:
The answer is "[tex]60.74^{\circ}[/tex]".
Explanation:
Cavity and benzene should be extended in equal quantities.
[tex]\to 1.18 \times 10^{-3}\times (1+ \Delta T \times 0.000051) = 1.1\times 10^{-3} \times (1+ \Delta T \times 0.00124)\\\\\to (\frac{1.18}{1.1})\times (1+ \Delta T \times 0.000051) = 1+ \Delta T \times 0.00124\\\\ \to 1.072\times (1+ \Delta T \times 0.000051) = 1+ \Delta T \times 0.00124\\\\ \to 1.072+ \Delta T \times 0.000054672 = 1+ \Delta T \times 0.00124\\\\ \to 1.072+ \Delta T \times 0.000054672 - 1- \Delta T \times 0.00124=0\\\\[/tex]
[tex]\to 0.072+ \Delta T \times 0.000054672 - \Delta T \times 0.00124=0\\\\ \to 0.072+ \Delta T ( 0.000054672 -0.00124)=0\\\\ \to \Delta T ( 0.000054672 -0.00124)= -0.072\\\\ \to \Delta T = -\frac{0.072}{( 0.000054672 -0.00124)}\\\\ \to \Delta T = -\frac{0.072}{-0.001185328 }\\[/tex]
[tex]\to \Delta T = \frac{0.072}{0.001185328 }\\\\ \to \Delta T = 60.74^{\circ}\\[/tex]
Test your prediction through calculation for the situations of the clay bob and the bouncy ball. Assume each has a mass of 100 grams, and each has an initial velocity of 20 m/s straight at the door. Ignore the effects of gravity. Calculate the change in momentum of
Answer:
a) Δp = -2.0 kgm / s, b) Δp = -4 kg m / s
Explanation:
In this exercise the change in moment of a ball is asked in two different cases
a) clay ball, in this case the ball sticks to the door and we have an inelastic collision where the final velocity of the ball is zero
Δp = p_f - p₀
Δp = 0 - m v₀
Δp = - 0.100 20
Δp = -2.0 kgm / s
b) in this case we have a bouncing ball, this is an elastic collision, as the gate is fixed it can be considered an object of infinite mass, therefore the final speed of the ball has the same modulus of the initial velocity, but address would count
v_f = - v₀
Δp = p_f -p₀
Δp = m v_f - m v₀
Δp = m (v_f -v₀)
Δp = 0.100 (-20 - 20)
Δp = -4 kg m / s
A long, straight, vertical wire carries a current upward. Due east of this wire, in what direction does the magnetic field point
The magnetic field of the wire will be directed towards west. Using right thumb rule one can get the direction of field lines.
A wave pulse travels along a stretched string at a speed of 200 cm/s. What will be the speed if:
a. The string's tension is doubled?
b. The string's mass is quadrupled (but its length is unchanged)?
c. The string's length is quadrupled (but its mass is unchanged)?
d. The string's mass and length are both quadrupled?
Answer:
a. 282.84 cm/s b. 100 cm/s c. 400 cm/s d. 200 cm/s
Explanation:
The speed of the wave v = √(T/μ) where T = tension and μ = mass per unit length = m/l where m = mass of string and l = length of string.
So, v = √(T/μ)
v = √(T/m/l)
v = √(Tl/m)
a. The string's tension is doubled?
If the tension is doubled, T' = 2T the new speed is
v' = √(T'l/m)
v' = √(2Tl/m)
v' = √2(√Tl/m)
v' = √2v
v' = √2 × 200 cm/s
v' = 282.84 cm/s
b. The string's mass is quadrupled (but its length is unchanged)?
If the mass is quadrupled, m' = 4m the new speed is
v' = √(Tl/m')
v' = √(Tl/4m)
v' = (1/√4)(√Tl/m)
v' = v/2
v' = 200/2 cm/s
v' = 100 cm/s
c. The string's length is quadrupled (but its mass is unchanged)?
If the length is quadrupled, l' = 4l the new speed is
v' = √(Tl'/m)
v' = √(T(4l)/m)
v' = √4)(√Tl/m)
v' = 2v
v' = 200 × 2 cm/s
v' = 400 cm/s
d. The string's mass and length are both quadrupled?
If the length is quadrupled, l' = 4l and mass quadrupled, m' = 4m, the new speed is
v' = √(Tl'/m')
v' = √(T(4l)/4m)
v' = √(Tl/m)
v' = v
v' = 200 cm/s
Pure water is an example of alan
A. Insulator
B. Metalloid
C. Conductor
D. Nonmetal
Answer: I think its A or C I'm not sure though sorry.
~~~~~NEED HELP ASAP~~~~~
A point on a rotating wheel (thin loop) having a constant angular velocityy of 300 rev/min, the wheel has a radius of 1.5m and a mass of 30kg. (I = mr^2)
a.) Determine the linear regression
b.) At this given angular velocity, what is the rotational kinetic energy?
Answer:
Centripetal Acceleration 18.75 m/s^2, Rotational Kinetic Energy 843.75 J
Explanation:
a Linear acceleration (we cant find tangential acceleration with the givens so we will find centripetal)
a= ω^2*r
ω= 300rev/min
convert into rev/s
300/60= 5rev/s
a= 18.75m/s^2
b) use Krot= 1/2 Iω^2
plug in gives
1/2(30*2.25)(25)= 843.75 J
A pilot flies her route in two straight-line segments. The displacement vector A for the first segment has a magnitude of 243 km and a direction 30.0o north of east. The displacement vector for the second segment has a magnitude of 178 km and a direction due west. The resultant displacement vector is R = A + B and makes an angle ? with the direction due east. Using the component method, find (a) the magnitude of R and (b) the directional angle ?.
(a) R = km
(b) ? = degrees
Answer:
a) [tex]R=126Km[/tex]
b) [tex]\theta=74.6\textdegree[/tex]
Explanation:
From the question we are told that:
1st segment
243km at Angle=30
2nd segment
178km West
Resolving to the X axis
[tex]F_x=243cos30+178[/tex]
[tex]F_x=33.44Km[/tex]
Resolving to the Y axis
[tex]F_y=243sin30+178sin0[/tex]
[tex]R=\sqrt{F_y^2+F_x^2}[/tex]
[tex]F_y=121.5Km[/tex]
Therefore
Generally the equation for Directional Angle is mathematically given by
[tex]\theta=tan^{-1}\frac{F_y}{F_x}[/tex]
[tex]\theta=tan^{-1}\frac{121.5}{33.44}[/tex]
[tex]\theta=74.6\textdegree[/tex]
Generally the equation for Magnitude is mathematically given by
[tex]R=\sqrt{F_y^2+F_x^2}[/tex]
[tex]R=\sqrt{33.44^2+121.5^2}[/tex]
[tex]R=126Km[/tex]
A 10 kg box is at static equilibrium and the downward pull of gravity acting on the box is 98 Newton’s what is the minimum force that would require to just pick up the box
Explanation:
static equilibrium means its on the floor or something
so slightly greater than 98 newtons in the upward direction
You are stranded in a stationary boat. Your friend is on a dock, but the boat is just beyond his reach. There is a 5 kg anchor in the boat. You'd like to get the boat to move closer to the dock so your friend can rescue you. Select from the following list what effect each change will have on the position of the boat relative to the dock. A. The boat will move closer to the dock. B. The boat will move away from the dock. C. The position of the boat relative to the dock will not change.
Answer:
running away and launching the anchor that will give a greater speed towards the dock v₄.
Explanation:
To try to bring the boat closer to the dock, several cases can be carried out.
* move inside the ship so that the center of mass changes and since moving away you have a speed v, the ship will approach the dock at a speed v₂,
* Throw the anchor in the opposite direction to the dock so that using the conservation of the moment the boat moves towards it, it moves at a speed v₃
* A combination of the two processes running away and launching the anchor that will give a greater speed towards the dock v₄.
In all cases, the friction must be zero.
All other movements move the ship away from the dock
The current in a conductor is 2.5A .explain the meaning of this statement
Answer:
In 1 second the amount of charge flowing through the conductor is 2.5 Q.
Explanation:
why kg is a fundamental unit?
This above answer helps a lot.
A rock, initially at rest with respect to Earth and located an infinite distance away is released and accelerates toward Earth. An observation tower is built 3 Earth-radii high to observe the rock as it plummets to Earth. Neglecting friction, the rock's speed when it hits the ground is _________ its speed at the top of the tower.
Answer:
the rock speed is increased
A rock is initially at rest concerning the earth, but the speed of the rock will increase when it hits the ground.
What is Friction?The resistance to something rolling or moving over another solid object is called friction. Even though frictional forces can be helpful, like the traction needed to walk without slipping, they also present a considerable amount of resistance to motion. About 20% of the engine power in a car is used to combat frictional forces in the moving parts.
The primary cause of friction between metals appears to be the forces of attraction, also known as adhesion, between the contact zones of the surfaces, which are always microscopically unequal. Because of friction caused by the imperfections of the tougher surface rubbing up against the softer surface, these "welded" connections are sheared.
To know more about Friction :
https://brainly.com/question/13000653
#SPJ2
Help me plssssssss cause I’m struggling
Answer:
I am pretty sure it is C
Explanation:
It can be found all over the universe
A car is moving with a velocity of45m/s. Is brought to rest in 5s.the distance travelled by car before it comes to rest is
Answer:
The car travels the distance of 225m before coming to rest.
Explanation:
v = 45m/s
t = 5s
Therefore,
d = v*t
= 45*5
= 225m
Magnets produce _________ in the spaces surrounding them
Answer:
magnetic field
Explanation:
Alice and Tom dive from an overhang into the lake below. Tom simply drops straight down from the edge, but Alice takes a running start and jumps with an initial horizontal velocity of 25 m/s. Neither person experiences any significant air resistance. Compare the time it takes each of them to reach the lake below.
a. Alice reaches the surface of the lake first
b. Tom reaches the surface of the lake first
c. Alice and Tom will reach the surface of the lake at the same time.
A uniformly charged thin rod of length L and positive charge Q lies along the x-axis with its left end at the origin as shown in Figure 1.
a. Set up a correct integral expression for the potential at point A,which lies a distance H above the right end of the rod. Point A has coordinates (L, H). You need to give appropriate limits of integration and expressions for r and dq
b. Set up a correct integral expression for the potential at point B on the x-axis, a distance D from the left end of the rod with the appropriate limits of integration.You need to give appropriate limits of integration and expressions for r and dq.
Answer:
b)
Explanation:
The period of a pendulum is the time it takes the pendulum to swing back and forth once. If the only dimensional quantities that the period depends on are the acceleration of gravity, g, and the length of the pendulum, l, what combination of g and l must the period be proportional to
Explanation:
Let T is the period of a pendulum. The SI unit of time is seconds (s).
It depends on the acceleration of gravity, g, and the length of the pendulum, l.
The SI unit of acceleration of gravity, g and the length of the pendulum, l are m/s² and m respectively.
If we divide m and m/s², we left with s². If the square root of s² is taken, we get s only i.e. the SI unit of period of a pendulum.
So,
[tex]T\propto \sqrt{\dfrac{l}{g}}[/tex]
Hence, this is the required solution.
Action and reaction are equal in magnitude and opposite in direction.Then Why do not balance each other
Answer:
Action and reaction are equal in magnitude and opposite in direction but they do not balance each other because they act on different objects so they don't cancel each other out.
hope this will help you more
A mixture of gaseous reactants is put into a cylinder, where a chemical reaction turns them into gaseous products. The cylinder has a piston that moves in or out, as necessary, to keep constant pressure on the mixture of 1 atm. The cylinder is also submerged in a large insulated water bath. The temperature of the water bath is monitored, and it is determined from this data that 133.0 kJ of heat flows into the system during the reaction. The position of the piston is also monitored, and it is determined from the data that the piston does 241.0 kJ of work on the system during the reaction.
a. Does the temperature of the water bath go up or down?
b. Does the piston move in or out?
c. Does heat flow into or out of the gaseous mixture?
d. How much heat flows?
Name the electrolyte in the chemical method of generating electricity
If the electron has half the speed needed to reach the negative plate, it will turn around and go towards the positive plate. What will its speed be, in meters per second, when it reaches the positive plate in this case
Answer:
v = -v₀ / 2
Explanation:
For this exercise let's use kinematics relations.
Let's use the initial conditions to find the acceleration of the electron
v² = v₀² - 2a y
when the initial velocity is vo it reaches just the negative plate so v = 0
a = v₀² / 2y
now they tell us that the initial velocity is half
v’² = v₀’² - 2 a y’
v₀ ’= v₀ / 2
at the point where turn v = 0
0 = v₀² /4 - 2 a y '
v₀² /4 = 2 (v₀² / 2y) y’
y = 4 y'
y ’= y / 4
We can see that when the velocity is half, advance only ¼ of the distance between the plates, now let's calculate the velocity if it leaves this position with zero velocity.
v² = v₀² -2a y’
v² = 0 - 2 (v₀² / 2y) y / 4
v² = -v₀² / 4
v = -v₀ / 2
We can see that as the system has no friction, the arrival speed is the same as the exit speed, but with the opposite direction.
Question 4(Multiple Choice Worth 4 points)
(02.04 MC)
Which explanation justifies why the theory of evolution is a theory and not a law?
Predicts an organism's ability to adapt to its environment
It can be expressed as a simple mathematical statement
Explains the existence of diverse forms of life on Earth
O Additional evidence will change the theory into a law
Answer:
A(predicts an organisms ability to adapt to its enviroment, it is not a fact that each organization can adapt)
Explanation:
What best describes a societal law
Answer:
Societal laws are based on the behavior and conduct made by society or government.hope it helps.stay safe healthy and happy.7. If a load of 300N is pulled along the inclined plane shown in the figure, answer the following. B 200 N 0.5m 2m 300 N А i. Calculate the VR and MA of the inclined plane. Calculate the input work and output work. ii.what efficiency of inclined plane?iv.what should be the length of inclined plane if same load has to be pulled with a50N effort for the same efficiency as above
Explanation:
700n I think friend .. if worng
