Power output = volts x amps
Power output = 170 volts x 0.1 amps
Power output = 18 watts
The following contribute to accidents when a teen driver has other teens as passengers
Answer:
When a teen driver drives with a lot of his peers as passengers they may lead to distraction which may later end up in accident as the driver was distracted
Overconfidence, lack of focus, and phone while driving are the factors contribute to accidents when a teen driver controls other teens as passengers,
What are the factors contribute to accidents when a teen driver has other teens as passengers?When a teen driver drives with a lot of his peers as passengers they may direct to distraction which may later end up in casualty as the driver was distracted.
Several studies have indicated that passengers substantially increase the chance of crashes for young, novice drivers. This improved risk may result from distractions that young passengers complete for drivers.Teens driving with a teen or young adult passengers existence of teen or young adult passengers raises the crash risk of unsupervised teen drivers. This risk grows with each additional teen or a young adult passenger.
Crash risk is two- to six times more significant for those who utilize a cellphone while driving resembled for drivers who are not distracted. Using a phone delays reaction time increases lane deviations, and forces drivers to look away from the road for extended times.
Overconfidence, lack of focus, and phone while driving are the factors contribute to accidents when a teen driver controls other teens as passengers,
To learn more about factors contribute to accidents refer to:
https://brainly.com/question/4853141
#SPJ2
Mary and her younger brother Alex decide to ride the carousel at the State Fair. Mary sits on one of the horses in the outer section at a distance of 2.0 m from the center. Alex decides to play it safe and chooses to sit in the inner section at a distance of 1.1 m from the center. The carousel takes 5.8 s to make each complete revolution.
Required:
a. What is Mary's angular speed %u03C9M and tangential speed vM?
b. What is Alex's angular speed %u03C9A and tangential speed vA?
Answer:
you can measure by scale beacause we dont no sorry i cant help u but u can ask me some other Q
if Petrol diesel etc catches fire one should never try to extinguish in using water why?
Answer:
because both petrol and diesel are oil
Explanation:
oil floats on water that's why if we will try to extinguish with water so the fire will float on water
hope u like my answer
please mark methe brainest
The pressure exerted at the bottom of a column of liquid is 30 kPa. The height of the
column is 3,875 m. What type of liquid is used?
Answer:
For example, the pressure acting on a dam at the bottom of a reservoir is ... pressure = height of column × density of the liquid × gravitational field ... The density of water is 1,000 kg/m 3.
Define measurements.
Answer:
act or process of measuring
Explanation:
Explanation:
the comparison of an unknown quantity with a known quantity.
Which level of government relies the most on income tax?
OA.
federal
state
OC.
local
Answer:
Its the Federal government
d. On the afternoon of January 15, 1919, an unusually warm day in Boston, a 17.7-m-high, 27.4-m-diameter cylindrical metal tank used for storing molasses ruptured. Molasses flooded into the streets in a 5-m-deep stream, killing pedestrians and horses and knocking down buildings. The molasses had a density of 1600 kg>m3 . If the tank was full before the accident, what was the total outward force the molasses exerted on its sides
Answer:
F = 1.638 x 10⁸ N = 163.8 MN
Explanation:
The total force exerted by the molasses is given as:
F = PA
where,
F = Force exerted by the molasses = ?
P = Pressure = ρgh
ρ = density of molasses = 1600 kg/m³
g = acceleration due to gravity = 9.81 m/s²
h = height of tank = 17.7 m
A = cross-sectional area of tank = πr²
r = radius of tank = 27.4 m/2 = 13.7 m
Therefore,
[tex]F = \rho ghA = \rho gh(\pi r^2)\\\\F = (1600\ kg/m^3)(9.81\ m/s^2)(17.7\ m)(\pi)(13.7\ m)^2[/tex]
F = 1.638 x 10⁸ N = 163.8 MN
Infrared radiation from young stars can pass through the heavy dust clouds surrounding them, allowing astronomers here on Earth to study the earliest stages of star formation, before a star begins to emit visible light. Suppose an infrared telescope is tuned to detect infrared radiation with a frequency of 4.39 THz. Calculate the wavelength of the infrared radiation.
Answer:
[tex]\lambda=6.83\times 10^{-5}\ m[/tex]
Explanation:
Given that,
An infrared telescope is tuned to detect infrared radiation with a frequency of 4.39 THz.
We know that,
1 THz = 10¹² Hz
So,
f = 4.39 × 10¹² Hz
We need to find the wavelength of the infrared radiation.
We know that,
[tex]\lambda=\dfrac{c}{f}\\\\\lambda=\dfrac{3\times 10^8}{4.39\times 10^{12}}\\\\=6.83\times 10^{-5}\ m[/tex]
So, the wavelength of the infrared radiation is [tex]6.83\times 10^{-5}\ m[/tex].
a. Give an example of the conversion of light energy to electrical energy.
b. Give an example of chemical energy converting to heat energy.
c. Give an example of mechanical energy converting to heat energy.
Explanation:
a) photovoltaic cell is a semiconductor device and it converts light energy to electrical energy
b) burning of coal converts chemical energy to heat energy
c) rubbing of both hands against each other converts mechanical to heat energy
Answer:
a. solar cells
b.coal,wood,petroleum
c.rubbing ours palms
how did kepler discoveries contribute to astronomy
Answer:
They established the laws of planetary motion. They explained how the Sun rises and sets. They made astronomy accessible to people who spoke Italian.
Explanation:
a concrete has a height of 5m and has unit area 3m² supports a mass of 30000kg.
Determine the stress, strain and change in height
Answer:
stress = 98000 N/m^2
strain = 3.92 x 10^-6
change in height = 0.0196 mm
Explanation:
Height, h = 5 m
Area, A = 3 m²
mass, m = 30000 kg
Stress is defined as the force per unit area.
[tex]stress = \frac{mg}{A}\\\\stress = \frac{30000\times 9.8}{3}\\\\stress = 98000 N/m^2[/tex]
Young's modulus of concrete is Y = 2.5 x 10^10 N/m^2
Young's modulus is defined as the ratio of stress to the strain.
[tex]Y = \frac{stress}{strain}\\\\2.5\times 10^{10}= \frac{98000}{strain}\\\\strain = 3.92\times 10^{-6}[/tex]
let the change in height is h'.
Strain is defined as the ratio of change in height to the original height.
[tex]3.92\times 10^{-6} = \frac{h'}{5}\\\\h' = 1.96\times 10^{-5}m = 0.0196 mm[/tex]
Drawing a shows a displacement vector (450.0 m along the y axis). In this x, y coordinate system the scalar components are Ax 0 m and Ay 450.0 m. Suppose that the coordinate system is rotated counterclockwise by 35.0, but the magnitude (450.0 m) and direction of vector remain unchanged, as in drawing b. What are the scalar components, Ax and Ay, of the vector in the rotated x, y coordinate system
Answer:
x ’= 368.61 m, y ’= 258.11 m
Explanation:
To solve this problem we must find the projections of the point on the new vectors of the rotated system θ = 35º
x’= R cos 35
y’= R sin 35
The modulus vector can be found using the Pythagorean theorem
R² = x² + y²
R = 450 m
we calculate
x ’= 450 cos 35
x ’= 368.61 m
y ’= 450 sin 35
y ’= 258.11 m
Question 8 a-e plz
Answer:
(a) t = 0 s
(b) t = 0 s, 30 s, 55 s
(c) t = 40 s to t = 60 s
(d) t = 10 s to t = 15 s
(e) a = 6 m/s^2
Explanation:
(a) The car is at starting position at t = 0 s and v = 0 m/s.
(b) The velocity of car is zero when the time is t = 0 s, 30 s and 55 s.
(c) from t = 40 s to 60 s the car is moving in the negative direction.
(d) The fastest speed is 60m/s from t = 10 s to t = 15 s.
(e) The slope of the velocity time graph gives acceleration.
a = (60 - 0) / (10 - 0) = 6 m/s^2
You are on an airplane that is landing. The plane in front of your plane blows a tire. The pilot of your plane is advised to abort the landing, so he pulls up, moving in a semicircular upward-bending path. The path has a radius of 450 m with a radial acceleration of 17 m/s^2.
Required:
What is the plane's speed?
Answer:
v = 87.46 m/s
Explanation:
The radial acceleration is the centripetal acceleration, whose formula is given as:
[tex]a_c = \frac{v^2}{r}[/tex]
where,
[tex]a_c[/tex] = centripetal acceleration = 17 m/s²
v = planes's speed = ?
r = radius of path = 450 m
Therefore,
[tex]17\ m/s^2 = \frac{v^2}{450\ m}\\\\v^2 = (17\ m/s^2)(450\ m)\\\\v = \sqrt{7650\ m^2/s^2}[/tex]
v = 87.46 m/s
If the electron has half the speed needed to reach the negative plate, it will turn around and go towards the positive plate. What will its speed be, in meters per second, when it reaches the positive plate in this case
Answer:
v = -v₀ / 2
Explanation:
For this exercise let's use kinematics relations.
Let's use the initial conditions to find the acceleration of the electron
v² = v₀² - 2a y
when the initial velocity is vo it reaches just the negative plate so v = 0
a = v₀² / 2y
now they tell us that the initial velocity is half
v’² = v₀’² - 2 a y’
v₀ ’= v₀ / 2
at the point where turn v = 0
0 = v₀² /4 - 2 a y '
v₀² /4 = 2 (v₀² / 2y) y’
y = 4 y'
y ’= y / 4
We can see that when the velocity is half, advance only ¼ of the distance between the plates, now let's calculate the velocity if it leaves this position with zero velocity.
v² = v₀² -2a y’
v² = 0 - 2 (v₀² / 2y) y / 4
v² = -v₀² / 4
v = -v₀ / 2
We can see that as the system has no friction, the arrival speed is the same as the exit speed, but with the opposite direction.
The mass per unit length of the rope is 0.0500 kg/m. Find the tension. Express your answer in newtons.
Complete question:
A transverse wave on a rope is given by [tex]y \ (x, \ t) = (0.75 \ cm) \ cos \ \pi[(0.400 \ cm^{-1}) x + (250 \ s^{-1})t][/tex]. The mass per unit length of the rope is 0.0500 kg/m. Find the tension. Express your answer in newtons.
Answer:
The tension on the rope is 1.95 N
Explanation:
The general equation of a progressive wave is given as;
[tex]y \ (x,t) = A \ cos(kx \ + \omega t)[/tex]
Compare the given equation with the general equation of wave, the following parameters will be deduced.
A = 0.75 cm
k = 0.400π cm⁻¹
ω = 250π s⁻¹
The frequency of the wave is calculated as;
ω = 2πf
2πf = 250π
2f = 250
f = 250/2
f = 125 Hz
The wavelength of the wave is calculated as;
[tex]\lambda = \frac{2\pi}{k} \\\\\lambda = \frac{2\pi }{0.4 \pi} = 5 \ cm = 0.05 \ m[/tex]
The velocity of the wave is calculated as;
v = fλ
v = 125 x 0.05
v = 6.25 m/s
The tension on the rope is calculated as;
[tex]v = \sqrt{\frac{T}{\mu}} \\\\where;\\\\T \ is \ the \ tension \ of \ the \ rope\\\\\mu \ is \ the \ mass \ per \ unit \ length = 0.05 \ kg/m\\\\v^2 = \frac{T}{\mu} \\\\T = v^2 \mu\\\\T = (6.25)^2\times (0.05)\\\\T = 1.95 \ N[/tex]
Therefore, the tension on the rope is 1.95 N
An electron in a hydrogen atom is in a p state. Which of the following statements is true?
a.
The electron’s wavefunction has at least one node (i.e., at least one place in space where it goes to zero).
b.
The electron has an energy of -13.6 eV.
c.
The electron has a total angular momentum of ħ.
d.
The electron has a z-component of angular momentum equal to sqrt(2)* ħ.
Answer:
The electron’s wavefunction has at least one node (i.e., at least one place in space where it goes to zero).
Explanation:
We know that the p-orbitals have nodes. A node is a region where the probability of finding an electron goes down to zero.
P orbitals are oriented along the x,y,z Cartesian axes and are known to have angular nodes along the axes.
Hence, if an electron in a hydrogen atom is in a p state, the electron’s wavefunction has at least one node
how do you calculate voltage drop
Answer:
Multiply current in amperes by the length of the circuit in feet to get ampere-feet. Circuit length is the distance from the point of origin to the load end of the circuit.
Divide by 100.
Multiply by proper voltage drop value in tables. The result is voltage drop.
Explanation:
1.Lõi thép máy biến áp được ghép từcác lá thép là để:
(a) Giảm tổn hao công suất do dòng điện xoáy
(b) Giảm tổn hao công suất do từ trễ
(c) Giảm tổn hao công suất do dòng điện chạy qua dây quấn
(d) Giảm tất cảcác loại tổn hao công suất.
Answer:
Option (c)
Explanation:
1.The transformer core is assembled from steel sheets to:
(a) Reduced power loss due to eddy current
(b) Reduced power loss due to hysteresis
(c) Reduced power loss due to current flowing through the winding
(d) Reduce all types of power loss.
A transformer is a device which converts the low voltage into high and vice versa.
There are two types of a transformer.
Step up: It is used to convert low voltage into high.
Step down It is used to convert high voltage into high.
It depends on the number of turns in primary and the secondary coil.
The core of the transformer is laminated and it is in the form of sheets.
By using such type of core, the power loss due to the windings is reduced.
option (c) .
If the source moves, the wavelength of the sound in front of the direction of motion is____than the wavelength behind the direction of motion.
a. the same.
b. smaller than.
c. unrealted to.
d. larger then.
Answer:
B. Smaller than
Explanation:
This question is from the Doppler effect. As the object which is in motion goes off from the other, there's a reduction in the frequency. This is due to the fact that successive soundwave get to be longer. So that the pitch will then be lowered. When the person observing moves towards what is making the sound, each soundwave that follows gets faster than the previous.
why is unit of power is called derived unit?
Distance travelled by a body in unit time is called speed. it is a scalar quantity because it can be specified only by magnitude.
Help me with my physics, please
Paauto A: Isulat sa papel ang alpabetong Ingles at bilang I hanggang 10 sa istilong
Roman ng pagleletra.
Answer:
Explanation:
English alphabets numbered fro 1 to 26
and the numbers 1 to10 so they are written in roman numbers as
1 - I
2 - II
3 - III
4 - IV
5 -V
6 - VI
7 -VII
8 - VIII
9 - IX
10 -X
11 - XI
12 - XII
13 - XIII
14 - XIV
15 - XV
16 - XVI
17 - XVII
18 - XVIII
19 - XIX
20- XX
21 - XXI
22 - XXII
23 - XXIII
24 - XXIV
25 - XXV
26 - XXVI
A 10 kg box is at static equilibrium and the downward pull of gravity acting on the box is 98 Newton’s what is the minimum force that would require to just pick up the box
Explanation:
static equilibrium means its on the floor or something
so slightly greater than 98 newtons in the upward direction
What best describes a societal law
Answer:
Societal laws are based on the behavior and conduct made by society or government.hope it helps.stay safe healthy and happy.~~~~NEED HELP ASAP~~~~
Block A slides into block B along a frictionless surface. They are moving in the direction from left o the right.
Block A= 3kg
Block B= 4kg
Block A velocity before collision =30m/s.
Block B velocity before collision = 15 m/s
The velocity of block B after the collision is 20m/s.
a.) What is the velocity of block A after collision?
b.) Is the collision elastic? Show work to explain answer why or why not.
Answer:
Block A velocity is 23.33 m/s and the collission is not elastic.
Explanation:
a) m1v1 + m2v2 = m1v1' + m2v2'
Plug in givens
90+60=3v1'+80
solve for v1'= 23.33m/s
b) Find the initial and final kinetic energy of Block B
Ki= 1/2(4)(15)^2 + 1/2(3)(30)^2 = 1800 J
Kf= 1/2(4)(20)^2 + 1/2(3)*(23.33)^2= 1616.433J
Since Ki does not equal Kf the collision is not elastic
The current in a conductor is 2.5A .explain the meaning of this statement
Answer:
In 1 second the amount of charge flowing through the conductor is 2.5 Q.
Explanation:
Action and reaction are equal in magnitude and opposite in direction.Then Why do not balance each other
Answer:
Action and reaction are equal in magnitude and opposite in direction but they do not balance each other because they act on different objects so they don't cancel each other out.
hope this will help you more
Name the electrolyte in the chemical method of generating electricity
~~~~~NEED HELP ASAP~~~~~
A point on a rotating wheel (thin loop) having a constant angular velocityy of 300 rev/min, the wheel has a radius of 1.5m and a mass of 30kg. (I = mr^2)
a.) Determine the linear regression
b.) At this given angular velocity, what is the rotational kinetic energy?
Answer:
Centripetal Acceleration 18.75 m/s^2, Rotational Kinetic Energy 843.75 J
Explanation:
a Linear acceleration (we cant find tangential acceleration with the givens so we will find centripetal)
a= ω^2*r
ω= 300rev/min
convert into rev/s
300/60= 5rev/s
a= 18.75m/s^2
b) use Krot= 1/2 Iω^2
plug in gives
1/2(30*2.25)(25)= 843.75 J
