Answer:
34.64 cm
Explanation:
Given that:
The depth of the hole h = 10 cm
height of the water holding in the tank H = 40 cm
For a stream of flowing water, the distance (x) at which the stream strikes the floor can be computed by using the formula;
[tex]x = 2 \sqrt{h(H-h)}[/tex]
[tex]x = 2 \sqrt{10(40-10)}[/tex]
[tex]x = 2 \sqrt{10(30)}[/tex]
[tex]x = 2 \sqrt{300}[/tex]
[tex]x = 2 \times 17.32[/tex]
x = 34.64 cm
herical piece of candy is suspended in flowing water. The candy has a density of 1950 kg/m3 and has a 1.0 cm diameter. The water velocity is 1.0 m/s, the water density is assumed to be 1000.0 kg/m3, and the water viscosity is 1.010-3 kg/m/s. The diffusion coefficient of the candy solute in water is 2.010-9 m2/s, and the solubility of the candy solute in water is 2.0 kg/m3. Calculate the mass tran
Answer: Below is the complete question
A spherical piece of candy is suspended in flowing water. The candy has a density of 1950 kg/m3 and has a 1.0 cm diameter. The water velocity is 1.0 m/s, the water density is assumed to be 1000.0 kg/m3, and the water viscosity is 1.0x10-3 kg/m/s. The diffusion coefficient of the candy solute in water is 2.0x10-9 m2/s, and the solubility of the candy solute in water is 2.0 kg/m3. Calculate the mass transfer coefficient (m/s)
answer:
mass transfer coefficient = 9.56 * 10^-5 m/s
Explanation:
Candy density = 1950 kg/m^3
Candy diameter = 1 cm
Velocity of water = 1 m/s
water density = 1000 kg/m^3
Viscosity of water = 1 * 10^-3 kg/m/s
diffusion coefficient of candy in water = 2 * 10^-9 m^2/s
solubility of candy = 2 kg/m^3
Determine the mass transfer coefficient ( m/s )
( Sh) mass transfer coefficient ( flow across sphere ) = 2 + 0.6Re^1/2 * SC^1/3
where : Re = vdp / μ , Sh = KLd / Deff
attached below is the remaining solution .
mass transfer coefficient = 9.56 * 10^-5 m/s
1 A thing ring has a mass of 6kg and a radius of 20cm. calculate the rotational inertia.
Answer:
2400kgm²
Explanation:
Rotational inertia=mass x radius²
A rugby player passes the ball 7.00 m across the field, where it is caught at the same height as it left his hand.
(a) At what angle was the ball thrown if its initial speed was 12.0 m/ s, assuming that the smaller of the two possible angles was used?
(b) What other angle gives the same range, and why would it not be used?
(c) How long did this pass take?
Answer:
a) θ = 14.23º, b) θ₂ = 75.77, c) t = 0.6019 s
Explanation:
This is a missile throwing exercise.
a) the reach of the ball is the distance traveled for the same departure height
R = [tex]\frac{v_o^2 \ sin 2 \theta }{g}[/tex]
sin 2θ = [tex]\frac{Rg}{v_o^2}[/tex]
sin 2θ = 7.00 9.8 / 12.0²
2θ = sin⁻¹ (0.476389) = 28.45º
θ = 14.23º
the complementary angle that gives the same range is the angle after 45 that the same value is missing to reach 90º
θ ’= 90 -14.23
θ’= 75.77º
b) the two angles that give the same range are
θ₁ = 14.23
θ₂ = 75.77
the greater angle has a much greater height so the time of the movement is greater and has a greater chance of being intercepted by the other team.
C) the time of the pass can be calculated with the expression
x = v₀ₓ t
t = x / v₀ₓ
t = 7 / 11.63
t = 0.6019 s
Describe sound and record
Answer:
record is information created, received and maintained as evidence and information by an organization or person.in simpler terms it's a collection of of fields probably of different data types.
sound is however something loud or soft.which can be defined as vibrations that travel through the air or another medium.
I hope this helps
A circular parallel-plate capacitor whose plates have a radius of 25 cm is being charged with a current of 1.3 A. What is the magnetic field 11 cm from the center of the plates
The magnetic field at 11 cm from the center of the plates is 2.364 x 10⁻⁷ T.
Given;
radius of the circular plate, d = 25 cm = 0.25 m
current in the plate, I = 1.3 A
distance from the center of the circular plate, r = 11 cm = 0.11 m
To find:
magnetic field (B)The magnetic field from the given distance is calculated as from Biot Savart equation:
[tex]B = \frac{\mu_o I}{2\pi r} \\\\where;\\\\\mu_o \ is \ permeability \ of \ free \ space \ 4\pi \times 10^{-7} \ T.m/A\\\\B = \frac{(4\pi \times 10^{-7} ) \times (1.3)}{2\pi \times 0.11} \\\\B = 2.364 \ \times 10^{-6} \ T[/tex]
Therefore, the magnetic field 11 cm from the center of the plates is 2.364 x 10⁻⁷ T.
Learn more here: https://brainly.com/question/17035710
A plastic dowel has a Young's Modulus of 1.50 ✕ 1010 N/m2. Assume the dowel will break if more than 1.50 ✕ 108 N/m2 is exerted. What is the maximum force (in kN) that can be applied to the dowel assuming a diameter of 2.30 cm?
A.
52.3 kN
B.
62.3 kN
C.
72.3 kN
D.
42.3 N
Answer:
cobina
Explanation:
me 2
A painter sets up a uniform plank so that he can paint a high wall. The plank is 2 m long and weighs 400 N. The two supports holding up the plank are placed 0.2 m from either end. Show that the upwards force on each of the planks is 200 N. Draw a sketch.
The upward force on each supporting plank is 200 N
The given parameters include;
weight of the plank, W₁ = 400 Nlength of the plank, l = 2 mupward force of each supporting plank, = W₂ and W₃To show that the upward force of each supporting plank is 200 N, make the following sketch.
W₂ W₃
↑ ↑
-----------------------------------------------------------------------
0.2m ↓ 0.2m
400 N
The two supporting planks keeps the 2m plank in equilibrium position. If the plank is in equilibrium position the sum of the upward forces equals sum of the downward force.W₂ + W₃ = 400 N
But the distance of each supporting plank from the end is equal, (0.2m).
Then, W₂ = W₃
2W₂ = 400 N
W₂ = 400N/2
W₂ = 200 N
W₃ = 200 N
Therefore, the upward force on each supporting plank that keeps the plank in equilibrium position is 200 N.
To learn more about equilibrium forces visit: https://brainly.com/question/12582625
List what sources of uncertainty go into calculating the wavelength of the laser (no explanation necessary here). (b) Accurately report the uncertainties for these quantities. (c) Explain which of these contributes the most to the final uncertainty on the laser wavelength
Answer:
thanks for da 5points hoi
Explanation: thanks dawg
There can be uncertainty in calculating the wavelength of a laser light due to experimental errors
All measurements have an uncertainty, in the case of direct measurements the uncertainty is equal to the precision of the given instrument.
What are uncertainity in measuring ?Uncertainty means the range of possible values within which the true value of the measurement lies.
What are errors?
The deviation in the value of the measured quantity from the actual quantity or true value is called an error
(a) For the calculation of wavelength of laser light , the sources which can lead to uncertainty are
1. least count of measuring instruments like spectrometer or interferometer
2. Parallax error in the measurement
3. Error in identifying the order of fringes
4.. unable to identify the accurate reading of Vernier or circular scales present in the measuring instruments.
5. Propagating errors
What is least count?
The least count of a measuring instrument is the smallest and accurate value in the measured quantity that can be measured by instrument.
What is propagating error?When you have derived variables, that is, when measurements are made with different instruments, each with a different uncertainty, the way to find the uncertainty or error is that all the errors add up. which increases the uncertainty
b. The uncertainty in measurement due to least count depends on the instrument used for measurement f wavelength. A Michelson's
interferometer has the least count of .0001mm. whereas spectrometer has a least count of 0.5⁰. Hence uncertainty in the measurement by Michelson's interferometer is very less as compared to any other instrument.
C. The maximum uncertainty arises due to the least count , as all other errors can be minimized by taking an average value of many observations but the least count of an instrument do not change so uncertainty within the least count arises.
To know more on errors and uncertainty in measurements here
https://brainly.com/question/24652157
#SPJ2
An ink-jet printer steers charged ink drops vertically. Each drop of ink has a mass of 10-11 kg, and a charge due to 500,000 extra electrons. It goes through two electrodes that gives a vertical acceleration of 104 m/s2. The deflecting electric field is _____ MV/m.
Answer:
E = 1.25 MV / m
Explanation:
For this exercise let's use Newton's second law
F = m a
where the force is electric
F = q E
we substitute
q E = m a
E = m a / q
indicate there are 500,000 excess electrons
q = 500000 e
q = 500000 1.6 10⁻¹⁹
q = 8 10⁻¹⁴ C
the mass is m = 10⁻¹¹ kg and the acceleration a = 10⁴ m / s²
let's calculate
E = 10⁻¹¹ 10⁴ / 8 10⁻¹⁴
E = 0.125 10⁷ V / m = 1.25 10⁶ V / m
E = 1.25 MV / m
1.2miles=__________km
Answer:
1.931 kilometres is the answer of 1.2 miles
Answer and Explanation:
1 mile = 1.609 km
Set up a fraction to cancel the miles to get the kilometers.
[tex]\frac{1.2mi}{?km} *\frac{1.609}{1mi} = 1.9308km[/tex] <- This is the answer.
#teamtrees #PAW (Plant And Water)
Rays of light coming from the sun (a very distant object) are near and parallel to the principal axis of a concave mirror. After reflecting from the mirror, where will the rays cross each other at a single point?
The rays __________
a. will not cross each other after reflecting from a concave mirror.
b. will cross at the center of curvature.
c. will cross at the point where the principal axis intersects the mirror.
d. will cross at the focal point. will cross at a point beyond the center of curvature.
A concave mirror is an example of curved mirrors. So that the appropriate answer to the given question is option D. The rays will cross at the focal point.
A concave mirror is a type of mirror in which its inner part is the reflecting surface, while its outer part is the back of the mirror. This mirror reflects all parallel rays close to the principal axis to a point of convergence. It can also be referred to as the converging mirror.
In this type of mirror, all rays of light parallel to the principal axis of the mirror after reflection will cross at the focal point.
Therefore, the required answer to the given question is option D. i.e The rays will cross at the focal point.
For reference: https://brainly.com/question/20380620
It is easy to produce a potential difference of several thousand volts between your body and the floor by scuffing your shoes across a nylon carpet. When you touch a metal doorknob, you get a mild shock. Yet contact with a power line of comparable voltage would probably be fatal. Why is there a difference?
Answer:
In sof the friction with the nylon is very small and the current with the line e is largeummary
Explanation:
When we rub the shoes against the carpet, static electricity is produced, when you touch the metal knob you close the circuit and the current can circulate to three of the body, the value of this current is of the order of micro volts, for which a small discharge, the power that circulates through the body is very small of the order of 0.005 A
When you touch the power line, the voltage may be small, but the amount of current that can generate them is of the order of tens of amps, the electric shock is much greater per location.
In general there is a rule that if the body resumes more than P = 4000W the discharge could be fatal.
In sof the friction with the nylon is very small and the current with the line e is largeummary, the difference is that the current at the stop , so the paper that passes through the body is large and can be dangerous.
In contact with metal doorknob, get a mild shock while with power line of same voltage, fatal the body as the amount of current is more.
What is charging by friction?When the two materials are rubbed each other, then the electric charged generated between them.
This charging of materials, due to the rubbing of two materials against each other, is called the charging by friction.
It is easy to produce a potential difference of several thousand volts between the body and the floor by scuffing your shoes across a nylon carpet.
In this case, the potential difference may be higher, but the value of current is very low. Thus, when the body touches a metal doorknob, it will get a mild shock.
Now, in another case, the contact with a power line of comparable voltage would probably be fatal. This is because in the power line the amount of current is much higher.
Hence, in contact with metal doorknob, get a mild shock while with power line of same voltage, fatal the body as the amount of current is more.
Learn more about the charging by friction here;
https://brainly.com/question/8418256
A parallel-plate capacitor consists of two plates, each with an area of 29 cm2cm2 separated by 3.0 mmmm. The charge on the capacitor is 7.8 nCnC . A proton is released from rest next to the positive plate. Part A How long does it take for the proton to reach the negative plate
Answer:
t = 2.09 10⁻³ s
Explanation:
We must solve this problem in parts, first we look for the acceleration of the electron and then the time to travel the distance
let's start with Newton's second law
∑ F = m a
the force is electric
F = q E
we substitute
q E = m a
a = [tex]\frac{q}{m} \ E[/tex]
a = [tex]\frac{1.6 \ 10^{-19}}{ 9.1 \ 10^{-31} } \ 7.8 \ 10^{-9}[/tex]
a = 1.37 10³ m / s²
now we can use kinematics
x = v₀ t + ½ a t²
indicate that rest starts v₀ = 0
x = 0 + ½ a t²
t = [tex]\sqrt{\frac{2x}{a} }[/tex]
t = [tex]\sqrt{\frac {2 \ 3 \ 10^{-3}}{ 1.37 \ 10^3} }[/tex]
t = 2.09 10⁻³ s
SI units are used for the scientific works,why?
Answer:
SI is used in most places around the world, so our use of it allows scientists from disparate regions to use a single standard in communicating scientific data without vocabulary confusion
A cylinder is given a push and then rolls up an inclined plane. If the origin is the starting point, sketch the position, velocity, and acceleration of the cylinder vs. time as it goes up and then down the plane.
For example, we can take Water
In (A) Water has same mass and great volume
In (B) Water has same mass and lower volume
Will there be any change in its density then?
Answer:
yes there will be change in its density
If a proton and electron both move through the same displacement in an electric field, is the change in potential energy associated with the proton equal in magnitude and opposite in sign to the change in potential energy associated with the electron?
a. The magnitude of the change is smaller for the proton.
b. The magnitude of the change is larger for the proton.
c. The signs Of the two changes in potential energy are opposite.
d. They are equal in magnitude.
e. The signs of the two changes in potential energy are the same.
Answer: They are equal in magnitude.
- The signs of the two changes in potential energy are opposite
Explanation:
When the proton and electron both move through the same displacement in an electric field, the change in potential energy that is associated with the proton is equal in magnitude.
Also, it should be noted that the signs of the two changes in potential energy are opposite.
a volcano that may erupt again at some time in the distant future is
Assume that a friend hands you a 10-newton box to hold for her. If you hold the box without moving it at a height of 10 meters above the ground, how much work do you do
Answer:
100 Joules
Explanation:
Applying,
W = mgh................... Equation 1
Where W = workdone to hold the box above the ground, mg = weight of the box, h = height of the box.
From the question,
Given: mg = 10 newtons, h = 10 meters.
Substitute these values into equation 1
W = 10×10
W = 100 Joules.
Hence the amount of workdone is 100 Joules
One charge is fixed q1 = 5 µC at the origin in a coordinate system, a second charge q2 = -3.2 µC the other is at a distance of x = 90 m from the origin.
What is the potential energy of this pair of charges?
Answer:
5.4uC
Explanation:
A proton traveling at 17.6° with respect to the direction of a magnetic field of strength 3.28 mT experiences a magnetic force of 9.14 × 10-17 N. Calculate (a) the proton's speed and (b) its kinetic energy in electron-volts.
Answer:
a) The proton's speed is 5.75x10⁵ m/s.
b) The kinetic energy of the proton is 1723 eV.
Explanation:
a) The proton's speed can be calculated with the Lorentz force equation:
[tex] F = qv \times B = qvBsin(\theta) [/tex] (1)
Where:
F: is the force = 9.14x10⁻¹⁷ N
q: is the charge of the particle (proton) = 1.602x10⁻¹⁹ C
v: is the proton's speed =?
B: is the magnetic field = 3.28 mT
θ: is the angle between the proton's speed and the magnetic field = 17.6°
By solving equation (1) for v we have:
[tex]v = \frac{F}{qBsin(\theta)} = \frac{9.14 \cdot 10^{-17} N}{1.602\cdot 10^{-19} C*3.28 \cdot 10^{-3} T*sin(17.6)} = 5.75 \cdot 10^{5} m/s[/tex]
Hence, the proton's speed is 5.75x10⁵ m/s.
b) Its kinetic energy (K) is given by:
[tex] K = \frac{1}{2}mv^{2} [/tex]
Where:
m: is the mass of the proton = 1.67x10⁻²⁷ kg
[tex] K = \frac{1}{2}mv^{2} = \frac{1}{2}1.67 \cdot 10^{-27} kg*(5.75 \cdot 10^{5} m/s)^{2} = 2.76 \cdot 10^{-16} J*\frac{1 eV}{1.602 \cdot 10^{-19} J} = 1723 eV [/tex]
Therefore, the kinetic energy of the proton is 1723 eV.
I hope it helps you!
What is science?Give two examples of living beings?
Answer:
the study of the past
Explanation:
dogs and cats
Consider a 200-ft-high, 1200-ft-wide dam filled to capacity. Determine (a) the hydrostatic force on the dam and (b) the force per unit area of the dam near the top and near the bottom. Note: we will see that the resultant hydrostatic force will be
Answer:
a) [tex]F_g=1.5*10^9Ibf[/tex]
b) [tex]F_t=12490Ibf/ft^2[/tex]
[tex]F_b=0[/tex]
Explanation:
From the question we are told that:
Height [tex]h=200ft[/tex]
Width [tex]w=1200ft[/tex]
a)
Generally the equation for Dam's Hydro static force is mathematically given by
[tex]F_g=\rho*g*\frac{h}{2}(w*h)[/tex]
Where
[tex]\rho=Density\ of\ water[/tex]
[tex]\rho=62.4Ibm/ft^3[/tex]
Therefore
[tex]F_g=62.4*32.2*\frac{200}{2}(1200*200)[/tex]
[tex]F_g=1.5*10^9Ibf[/tex]
b)
Generally the equation for Dam's Force per unit area is mathematically given by
[tex]F=\rho*g*h[/tex]
For Top
[tex]F_t=\rho*g*h[/tex]
[tex]F_t=62.4*32.2*200[/tex]
[tex]F_t=12490Ibf/ft^2[/tex]
For bottom
[tex]Here \\H=0 zero[/tex]
Therefore
[tex]F_b=0[/tex]
The hydrostatic force on the dam is [tex]2.995 \times 10^9 \ lbF[/tex].
The force per unit area near the top is 86.74 psi.
The force per unit area near the bottom is zero.
Hydrostatic force
The hydrostatic force on the dam is the force exerted on the dam by the column of the water.
[tex]F = PA\\\\F = (\rho gh) \times (wh)\\\\F = (62.4 \times 32.17 \times 200) \times (1200 \times 200)\\\\F = 9.636 \times 10^{10} \ lb-ft/s^2\\\\1 \ lbF = 32.17\ lb-ft/s^2\\\\F = 2.995 \times 10^9 \ lbF[/tex]
Force per unit area near the topThe force per unit area is the pressure exerted near the top of the dam.
[tex]P = \rho gh\\\\P = 0.052 \times \rho h[/tex]
where;
P is pressure in PSI
ρ is density of water in lb/gal
h is the vertical height in ft
[tex]P = 0.052 \times 8.34 \times 200\\\\P = 86.74 \ Psi[/tex]
The pressure near the bottom is zero, become the vertical height is zero.
Learn more about hydrostatic pressure here: https://brainly.com/question/11681616
The cart travels the track again and now experiences a constant tangential acceleration from point A to point C. The speeds of the cart are 11.0 ft/s at point A and 18.0 ft/s at point C. The cart takes 5.00 s to go from point A to point C, and the cart takes 1.30 s to go from point B to point C. What is the cart's speed at point B
Answer:
The speed at B is 16.18 ft/s .
Explanation:
Speed at A, u = 11 ft/s
Speed at C, v' = 18 ft/s
Time from A to C = 5 s
Time from B to C = 1.3 s
Let the speed of car at B is v.
Let the acceleration is a.
From A to B
Use first equation of motion
v = u + a t
18 = 11 + a x 5
a = 1.4 ft/s^2
Let the time from A to B is t' .
t' = 5 - 1.3 = 3.7 s
Use first equation of motion from A to B
v = 11 + 1.4 x 3.7 = 16.18 ft/s
In the diagram, the crest of the wave is show by:
A
B
C
D
Answer:
D.
Explanation:
The crest of a wave refers to the highest point of a wave. This is illustrated by D.
Derive the dimension of coefficient of linear expansivity
Answer:
The SI unit of coefficient of linear expansion can be expressed as °C-1 or °K-1. ... The dimension of coefficient of linear expansion will be M0L0T0K−1.
A large metal sphere has three times the diameter of a smaller sphere and carries three times the charge. Both spheres are isolated, so their surface charge densities are uniform. Compare (a) the potentials (relative to infinity) and (b) the electric field strengths at their surfaces.
Answer:
A. Equals to that of the smaller sphere
B. 3 times less than that of the smaller sphere
Explanation:
(a) Equals to that of the smaller sphere
The potential of an isolated metal sphere, with charge Q and radius R, is kQ=R, so a sphere with charge 3Q and radius 3R has the same potential
b) 3 times less than that of the smaller sphere
However, the electric field at the surface of the smaller sphere is ?=? 0 = kQ=R2 , so tripling Q and R reduces the surface field by a factor of 1/3
Electron A is fired horizontally with speed 1.00 Mm/s into a region where a vertical magnetic field exists. Electron B is fired along the same path with speed 2.00 Mm/s. (i) Which electron has a larger magnetic force exerted on it
B will have the greater force
Fc=MV2 /R=Fm
The A particle has less centipetal force and larger radius so larger curve
Two long straight wires are suspended vertically. The wires are connected in series, and a current from a battery is maintained in them. What happens to the wires? What happens if the battery is replaced by an a-c source?
Answer:
(i) When a battery is connected inseries to two long parallel wires, the currents in the two wires will be in opposite directions. Due to which a force of repulsion will be acting between them and they are moving further apart.
(ii) When a battery is connected in parallel to two long parallel wires, the currents in the two wires will be in same direction. Due to it, a force of attraction will be acting between them and they are coming closer to each other.
hope it's help you ....!!!!!
plz mark as brain list and follow me #rishu...!!!!
Explanation:
Hope it will helps you lot!
g Light that is incident upon the eye is refracted several times before it reaches the retina. As light passes through the eye, at which boundary does most of the overall refraction occur?
Answer
Explanation
:giác mạc
