Consider a single crystal of some hypothetical metal that has the FCC crystal structure and is oriented such that a tensile stress is applied along a direction. If slip occurs on a (111) plane and in a direction, compute the stress at which the crystal yields if its critical resolved shear stress is 3.42 MPa.
The resolved shear stress (τR) can be calculated using the following formula:τR = σs cos φ cos λWhere,σs = tensile stress applied along a directionφ = angle between tensile stress direction and (111) planeλ = angle between the slip direction and [110] directionThe resolved shear stress (τR) should be compared to the critical resolved shear stress (τc) to determine if slip will occur. If τR > τc, slip will occur. If τR < τc, the crystal will remain undeformed.In this case, the slip direction is also along [110] and therefore φ = λ.
The critical resolved shear stress (τc) = 3.42 MPa. Hence, for slip to occur,τR > τc ⇒ σs cos φ cos λ > τc cos φ cos λ = 3.42 MPaSince φ = λ, we can simplify the above equation toσs > τc / cos φ⇒ σs > 3.42 MPa / cos φIf we assume φ = 45°, we can substitute in this value to get the value of σs at which slip occurs:σs > 4.83 MPa. Therefore, the stress at which the crystal yields is 3.42 MPa.
Learn more about shear stress at:
https://brainly.com/question/30530774
#SPJ11
two cars approach an ice-covered intersection. one car, of mass 1.27 103 kg, is initially traveling north at 11.6 m/s. the other car, of mass 1.70 103 kg, is initially traveling east at 11.6 m/s. the cars reach the intersection at the same instant, collide, and move off coupled together. find the velocity of the center of mass of the two-car system just after the collision.
The center of mass of the two-car system can be found by taking the weighted average of the velocities of the two cars.
The velocity of the center of mass is the average of the two cars' velocities, weighted by their masses. The velocity of the center of mass is:
Velocity of Center of Mass = (1.27 x 103 kg x 11.6 m/s + 1.70 x 103 kg x 11.6 m/s) / (1.27 x 103 kg + 1.70 x 103 kg) = 11.60 m/s.
Read more about the topic velocity:
https://brainly.com/question/80295?source=archive
#SPJ11
A sandbag is dropped from a balloon which is ascending vertically at a constant speed of 6 m/s.
If the bag is released with the same upward velocity of 6 m/s when t = 0 and hits the ground when t = 8 s, determine the speed of the bag as it hits the ground and the altitude of the balloon at this instant.
The speed of the bag as it hits the ground is -47.2 m/s and the altitude of the balloon at this instant is 245.6 m.
At t = 0, the sandbag is released with an upward velocity of 6 m/s. Since the balloon is ascending vertically at a constant speed of 6 m/s, the sandbag will be accelerating downwards due to the force of gravity.
Using the equation of motion v = u + at, we can calculate the speed of the sandbag at the time it hits the ground (t = 8 s). We can calculate the velocity by substituting u = 6 m/s, a = -9.8 m/s2 (acceleration due to gravity), and t = 8 s. This gives us a velocity of -47.2 m/s.
At the instant the sandbag hits the ground, the altitude of the balloon can be calculated using the equation s = ut + 1/2at2. We can calculate the altitude by substituting u = 6 m/s, a = -9.8 m/s2, and t = 8 s. This gives us an altitude of 245.6 m.
Therefore, the speed of the bag as it hits the ground is -47.2 m/s and the altitude of the balloon at this instant is 245.6 m.
To learn more about speed follow
https://brainly.com/question/14691279
#SPJ11
imagine swinging a ball in a circle at the end of a string. if the string that holds the ball breaks, what causes the ball to move in a straight line path?
When a ball is swung in a circle at the end of a string, it is constantly changing direction due to the force acting on it. This force is called the centripetal force, which is provided by the tension in the string.
When the string holding the ball breaks, there is no longer any force acting on the ball to keep it moving in a circular path. As a result, the ball moves in a straight line path in accordance with Newton's first law of motion, which states that an object at rest will remain at rest or an object in motion will continue to move in a straight line path at a constant speed unless acted upon by an external force.
In this case, the external force was the tension in the string, which was providing the centripetal force to keep the ball moving in a circular path. Once the string broke, the ball no longer experienced any centripetal force, and thus continued to move in a straight line path.
To learn more about centripetal force refer to:
brainly.com/question/11324711
#SPJ4
if the variable capacitor in an fm receiver ranges from 10.9 pf to 16.4 pf , what inductor should be used to make an lc circuit whose resonant frequency spans the fm band?
To create an LC circuit spanning the FM band with a variable capacitor of 10.9-16.4 pF, use the formula L = 1/(4π²f²C).
The inductor needed to make an LC circuit whose resonant frequency spans the FM band depends on the variable capacitor in the FM receiver. In your case, the variable capacitor ranges from 10.9 pF to 16.4 pF. To determine the inductor needed for the LC circuit, you can use the following formula:
L = (1/ (4π² * f² * C))
Where:
"L" is the inductor. "f" is the frequency of the LC circuit. "C" is the capacitor.For example, if you set the variable capacitor to 10.9 pF, the inductor needed to make an LC circuit whose resonant frequency spans the FM band would be:
L = (1/ (4π² * f² * 10.9 pF))
Learn more about circuit: https://brainly.com/question/29255502
#SPJ11
Sam (85 kg) takes off up a 50-m-high, 10 degree frictionless slope on his jet-powered skis. The skis have a thrust of 220 N. He keeps his skis tilted at 10 degree after becoming airborne. How far does Sam land from the base of the cliff?
Sam (85 kg) takes off up a 50-m-high, 10 degree frictionless slope on his jet-powered skis. The skis have a thrust of 220 N. He keeps his skis tilted at 10 degree after becoming airborne. Sam lands about 109.9 meters from the base of the cliff.
To solve this problem, we can use the conservation of energy principle. At the bottom of the slope, all of Sam's energy is in the form of potential energy:
Potential energy = mgh
where m is Sam's mass (85 kg), g is the acceleration due to gravity [tex](9.81 m/s^2)[/tex], and h is the height of the slope (50 m).
Potential energy = [tex](85 kg) \times (9.81 m/s^2) \times (50 m) = 41,287.5 J[/tex]
As Sam takes off up the slope, his potential energy is converted to kinetic energy and then to a combination of kinetic and potential energy as he becomes airborne. We can use the conservation of energy to find Sam's speed at the top of the slope:
Potential energy at bottom = Kinetic energy at top
[tex]mgh = (1/2)mv^2[/tex]
where v is Sam's speed at the top of the slope.
[tex]v = \sqrt{(2gh)} = \sqrt{(2 \times 9.81 m/s^2 \times 50 m)} = 31.3 m/s[/tex]
Now, we can use Sam's speed and the angle of his skis to find his horizontal velocity:
Horizontal velocity = v cos(theta)
where theta is the angle of the skis after becoming airborne (10 degrees).
Horizontal velocity = 31.3 m/s x cos(10 degrees) = 30.2 m/s
Finally, we can use the horizontal velocity and Sam's hang time to find the distance he travels:
Distance = Horizontal velocity x Hang time
where hang time is the time Sam spends in the air. Hang time can be found using the formula:
Hang time = (2v sin(theta)) / g
Hang time = (2 x 31.3 m/s x sin(10 degrees)) / 9.81 [tex]m/s^2[/tex] = 3.64 s
Distance = 30.2 m/s x 3.64 s = 109.9 m
for such more question on lands
https://brainly.com/question/29820168
#SPJ11
Can we use our brainly points.
What did the triangle say to the circle?
Your pointless
Answer:
i actually giggled at that oml.
Explanation:
that was good
Part A A canoe is designed to have very little drag when it moves along its length. Riley, mass 62 kg, sits in a 21 kg canoe in the middle of a lake. She dives into the water off the front of the canoe, along the axis of the canoe. She dives forward at 1.7 m/s relative to the boat. Just after her leap, how fast is she moving relative to the water? Express your answer with the appropriate units Value Units Submit Request Answer ▼ Part B Just after her leap, how fast is the canoe moving relative to the water? Express your answer with the appropriate units. (c)EValue Units
The speed of Riley relative to the water is 1.7 m/s. and the speed of canoe relative to the water is 0 m/s.
How fast is Riley moving relative to the water?The equation needed to solve the problem is the following:
Final Velocity = Initial Velocity + (Acceleration × Time)
The steps to solve for speed of Riley are the following:
Mass of Riley = 62 kg
Mass of canoe = 21 kg
Speed of leap relative to the boat = 1.7 m/s
By using the equation for conservation of momentum (also known as the center of mass formula):
m₁v₁ + m₂v₂ = (m₁ + m₂)vf
Solve for the unknown variable: vf = (m₁v₁ + m₂v₂) / (m₁ + m₂)
Plugging in the values given, you get: vf = (62 kg × 1.7 m/s) / (62 kg + 21 kg) = 1.2 m/s
Therefore, Riley is moving at 1.2 m/s relative to the water.
Velocity of the canoe relative to the water can be determined by using the equation for conservation of momentum (also known as the center of mass formula):
m₁v₁ + m₂v₂ = (m₁ + m₂)vf
v₂ = [(m₁ + m₂)vf - m₁v₂] / m₂
Plugging in the values given, you get: v₂ = [(62 kg + 21 kg) × 1.2 m/s - 62 kg × 1.7 m/s] / 21 kg = 0 m/s
Therefore, the canoe is not moving relative to the water.
Learn more about Relative speed here:
https://brainly.com/question/14362959
#SPJ11
a solid plastic cylinder of radius 2.33 cm and length 6.30 cm. find the net charge of this cylinder, in nc (nanocoulombs), if it carries a uniform volumetric charge density of 540 nc/m3 throughout the whole volume of the plastic.
The net charge of a solid plastic cylinder of radius 2.33 cm and length 6.30 cm, carrying a uniform volumetric charge density of 540 nc/m3, is equal to 0.0583 nC (nanocoulombs)
To determine the net charge of a cylinder, the formula Q =ρV has to be used where Q is the net charge, ρ is the uniform volumetric charge density, and V is the volume of the cylinder.
ρ is given as 540 nc/m³.
V is calculated using the formula
V = πr²h
where r is the radius and h is the length.
π is approximated to be 3.14.
h is given as 6.30cm
r is 2.33cm
so the calculation for V becomes;
V = πr²h
V = 3.14 x 2.33² x 6.3
V = 108.02 cm³ or 108.02 x 10⁻⁶ m³.
Substitute the values of Q and V into the equation and solve for Q:
Q = ρVQ = 540 nc/m³ x 108.02 x 10⁻⁶ m³
Q = 0.0583 nc (to 3 decimal places)
Therefore the net charge of this cylinder, in nc (nanocoulombs) is 0.0583nc.
Learn more about net charge at https://brainly.com/question/26036371
#SPJ11
a microwave oven operates at 2.90 ghz . what is the wavelength of the radiation produced by this appliance?
The given frequency of a microwave oven is 2.90 GHz. We have to find the wavelength of the radiation produced by this appliance. The speed of light is a constant value of 3 x 108 m/s. The relation between frequency and wavelength of electromagnetic radiation is given by:
c = fλ
Where,
c = speed of lightf = frequency of radiationλ = wavelength of radiationWe can rearrange this equation to get the formula for wavelength:
λ = c / f
Substituting the given values, we get:
λ = 3 x 108 / (2.90 x 109)λ = 0.1034 m or 10.34 cmTherefore, the wavelength of the radiation produced by the microwave oven is 10.34 cm.
Learn more about microwave oven: https://brainly.com/question/3164926
#SPJ11
Which statement describes what most likely occurs when a magnetic compass is placed next to a simple circuit made from a battery, a light bulb, and a wire?A magnetic field created by the compass causes the light bulb to stop working.A magnetic field created by the electric current causes the compass needle to move.A magnetic field created by the compass increases the current in the electrical circuit.A magnetic field created by the electric current places negative charges on the compass.
A magnetic field created by the electric current causes the compass needle to move. This is the most likely outcome when a magnetic compass is placed adjacent to a basic electrical circuit consisting of a battery, a light bulb, and a wire.
A magnetic field is created around a wire as electricity flows through it. The compass needle moves as a result of the interaction between this magnetic field and the Earth's magnetic field. Consequently, the magnetic field produced by the electric current in the wire causes the compass needle to move when a magnetic compass is put next to a basic circuit comprised of a battery, a light bulb, and a wire. The interplay of magnetic fields and electric currents is employed in numerous applications, such as electric motors and generators, to transform electrical energy into mechanical energy and vice versa.
learn more about magnetic compass here:
https://brainly.com/question/2264542
#SPJ4
A basketball rolls across a floor without slipping, with its centerof mass moving at a certain velocity. A block of ice of the samemass is set sliding across the floor with the same speed along aparallel line.(a) How do their energies compare?The ice has more kineticenergy.They have equal kineticenergies.The basketball has more kineticenergy.
The correct option is A, A block of ice of the same mass is set sliding across the floor with the same speed along a parallel line The ice has more kinetic energy.
Kinetic energy is a type of energy that an object possesses by virtue of its motion. It is defined as the energy an object has due to its motion and is proportional to the mass of the object and the square of its velocity. The formula for kinetic energy is KE = 1/2mv², where m is the mass of the object and v is its velocity.
Kinetic energy is a scalar quantity and has units of joules in the International System of Units (SI). It is a fundamental concept in physics and is used to describe many physical phenomena, including the motion of particles, the behavior of gases, and the motion of waves. In many cases, kinetic energy can be transformed into other forms of energy. For example, when a ball is thrown upwards, its kinetic energy is gradually converted into gravitational potential energy as it moves higher and higher.
To learn more about Kinetic energy visit here:
brainly.com/question/26472013
#SPJ4
Complete Question:
Basketball rolls across a floor without slipping, with its center of mass moving at a certain velocity. A block of ice of the same mass is set sliding across the floor with the same speed along a parallel line.(a) How do their energies compare?
A). The ice has more kinetic energy.
B). They have equal kinetic energies.
C). The basketball has more kinetic energy.
what device is used to shunt transient current to ground in the event of an indirect lightning strike?
In the event of an indirect lightning strike, a Surge Protection Device (SPD) is used for shunting transient current to the ground. An SPD is a protective device that limits the voltage supplied to an electrical system by either blocking or shorting to ground any unwanted voltages above a safe threshold. This can help protect against damage from transient current, a short, high-energy burst of electricity.
A surge protector is an electrical device that protects electronic devices from power surges and other electrical disturbances. The device will shield the equipment that is plugged into it from the spikes that are present in an electrical supply.The term “surge protector” is frequently used in reference to a category of products that is also known as a “transient voltage suppressor.” This name provides insight into how these devices work. They suppress transient voltage, which is a sudden surge of voltage that is brief in nature
.How do surge protectors work?
Surge protectors work by preventing transient voltage spikes from reaching sensitive electrical equipment. These devices typically consist of a metal oxide varistor, which is a component that is used to divert any unwanted voltage away from sensitive electronics and toward a grounded element.The varistor is connected to a metal oxide varistor, which is responsible for conducting the unwanted voltage away from the equipment and toward the ground. Surge protectors will reduce voltage to a safe level by grounding the unwanted voltage. Surge protectors are used to protecting a wide range of electronic devices, including computers, audio equipment, and video equipment.
For more details go through the link: https://brainly.com/question/30869810
#SPJ11
Transient current refers to an electrical current that flows for a brief period. Transient currents are caused by temporary changes in voltage, such as those caused by electrical discharges, power outages, and other events. Surge currents are another name for transient currents, and they are often used interchangeably.
A lightning strike is an electrical discharge from the atmosphere to the earth's surface. Thunderstorms, which are associated with lightning, are the most frequent natural cause of the electrical discharge. A lightning bolt can produce extremely high voltages and currents, posing a significant threat to electrical systems and the people who operate them.
A surge protector is a device that is intended to protect electrical devices from voltage spikes, surges, and other power fluctuations. Surge protectors work by shunting transient currents to the ground in the event of an indirect lightning strike. They can also be used to safeguard against other types of power surges, such as those caused by power outages, grid switching, and other issues. Surge protectors are often utilized in industrial and commercial settings, as well as in homes.
For more information regarding this topic, you can click the below link
https://brainly.com/question/1100341
#SPJ11
Complete the following sentence.
A diameter is also a...
Answer:
A diameter is also a double of radius
a rod of negligible mass may rotate about a pivot such that frictional forces are considered to be negligible. the figure shows two cases, case 1 and case 2, in which two applied forces of the same magnitude, fh and fv, can be exerted on the rod. which of the following two statements are correct about the net torque exerted on the rod? select two answers.
The following are accurate assertions regarding the net torque applied to the rod in case 1, the rod is subjected to a smaller net torque than in case 2, and vice versa. The correct options are A and D.
What is torque?The rotating force imposed on an object is measured in torque. The tendency of an object to rotate about an axis is a vector quantity.
In Case 1, the torques of the two forces, FH and Fy, total up because they are acting in the same direction.
The net torque is determined by multiplying the force by the lever arm, which is the distance from the pivot to the force's line of action.
Case 2's two opposing forces, FH and Fy, cancel out each other's torques because of this. While the torque caused by Fy is anticlockwise, the torque caused by FH is clockwise.
The rod's angular acceleration is dependent on its moment of inertia and net torque; however, the angular acceleration cannot be calculated with the information provided.
Thus, the correct options are A and D.
For more details regarding torque, visit:
https://brainly.com/question/30338175
#SPJ6
Your question seems incomplete, the probable complete question is:
you are designing a spacecraft to a giant planet. which planet is your spacecraft going to study, and what is it going to learn about the planet?
A spacecraft is a vehicle that can travel into space. The spacecraft can be used to study other planets, asteroids, and comets in our solar system. Spacecraft has the ability to collect data, take photographs, and make measurements about the planets and other space objects.
What can you learn about a planet?With a spacecraft, scientists can learn a lot about planets. Some of the things that can be learned include the following:
The chemical composition of the planet's surface and atmosphere.The geology of the planet, such as mountains, valleys, and other features.How the planet rotates, and how long it takes to complete one rotation.The planet's weather patterns and climate, such as temperature and wind speeds.The planet's magnetic field, and how it interacts with the solar wind.The planet's moons and rings, and how they interact with the planet.In conclusion, with a spacecraft, scientists can learn a lot about planets. Information about a planet can vary depending on the planet.
Learn more about spacecraft: https://brainly.com/question/24571549
#SPJ11
Resistors to be used in a circuit have average resistance 200 ohms and standard deviation 10 ohms. Suppose 25 of these resistors are randomly selected to be used in a circuit.
a) What is the probability that the average resistance for the 25 resistors is between 199 and 202 ohms?
b) Find the probability that the total resistance does not exceed 5100 ohms.
The likelihood that the mean impedance of 25 resistors is within the range of 199 to 202 ohms is 0.842, as per the principle of probability.
The computation can be done using the normal distribution equation P(a≤x≤b) = F(b) - F(a).
F(x) denotes the cumulative probability of the specified normal distribution.
The mean impedance is 200 ohms with a standard deviation of 10 ohms, hence F(199) = 0.155 and F(202) = 0.997. Consequently, the likelihood that the mean impedance of 25 resistors is between 199 and 202 ohms is 0.997 - 0.155 = 0.842.
The probability that the total impedance will be below 5100 ohms is 0.999. This can be calculated using the normal distribution formula P(x≤a) = F(a), where F(x) represents the cumulative probability of the specific normal distribution.
The mean impedance is 5,000 ohms with a standard deviation of 250 ohms, hence F(5100) = 0.999. Therefore, the probability that the total impedance will not exceed 5100 ohms is 0.999.
To learn more about the probability of mean resistance, visit: Brainly.com/question/18650146
#SPJ11
according to his physician, ryan has iron-deficiency anemia. the doctor recommended he eat iron-fortified cereal daily. which of the following foods or beverages would be the best accompaniment for an iron-fortified cereal and why?
According to Ryan's physician, Ryan has iron-deficiency anemia. The physician recommended he eats iron-fortified cereal daily. Orange juice would be the best accompaniment for an iron-fortified cereal.
Why orange juice is the best accompaniment for an iron-fortified cereal?
Orange juice is the best accompaniment for an iron-fortified cereal because it is high in vitamin C, which enhances iron absorption. The body absorbs heme iron, which is found in animal proteins, much more easily than non-heme iron, which is found in plant-based foods and iron-fortified products.However, consuming iron-rich foods and iron-fortified cereals with foods high in vitamin C can help enhance the absorption of non-heme iron.
Vitamin C aids the absorption of non-heme iron by transforming it into a form that is more easily absorbed by the body. As a result, consuming iron-fortified cereal with vitamin C-rich orange juice or grapefruit juice can increase the iron absorption rate of the body.
Learn more about anemia on
https://brainly.com/question/8197071
#SPJ11
Which of the following transitions would emit the shortest wavelength? select one; (a) n=2 to 1 (b) n=1 to 3 (c) n=1 to 2 (d) n=3 to 1
(d) n=3 to 1 would emit the shortest wavelength. Due to the largest energy differential between the two energy levels, the transition from n=3 to n=1 would emit the shortest wavelength.
Electromagnetic radiation, such as light, is released when an electron moves from a higher energy level (n) to a lower energy level (m). E = hc/, where E is the energy, h is Planck's constant, c is the speed of light, and is the wavelength of the radiation, relates the energy of the emitted radiation to the energy difference between the two levels.
Transitions to lower energy levels release greater energy photons with shorter wavelengths because as n decreases, energy levels move closer together. Option (d) is the appropriate response since the transition from n=3 to n=1 has the greatest energy difference and hence the shortest wavelength.
learn more about wavelength here:
https://brainly.com/question/31143857
#SPJ4
A magnifying glass with focal length 15 cm is placed 10 cm above a stamp. The image of the stamp is located a. 15 cm from the magnifying glass. b. 30 cm above the stamp. c. 30 cm above the magnifying glass. d. 30 cm below the stamp. e. 30 cm below the magnifying glass.
The image of the stamp when a magnifying glass with focal length 15 cm is placed 10 cm above a stamp is located 30 cm above the magnifying glass. The correct answer is Option C.
Let the object distance, u be -10cm (since the stamp is placed 10 cm above the magnifying glass).
Let the focal length of the lens, f be 15cm.
So, the magnification, m is given as:
m = v/u (where v is the image distance)
Using the lens formula, we can say that:
1/f = 1/v - 1/u (where v is the image distance and u is the object distance)
Plugging in the given values into the formula we have:
1/15 = 1/v + 1/10
Multiplying both sides of the equation by 30v, we have:
2v = 3(30 - v)
Solving for v, we have:
v = 30/2 = 15 cm
Since v is positive, it means that the image of the stamp is formed on the other side of the lens (on the side of the lens where the image of the stamp is formed, we measure the distance from the lens from this side). Hence, the image is located 15cm from the lens. Since the stamp is located 10 cm above the magnifying glass, the image of the stamp is located 15 + 10 = 25cm above the object or the magnifying glass. Thus, the correct option is c. 30 cm above the magnifying glass.
Learn more about magnification here: https://brainly.com/question/1599771
#SPJ11
The symbol EF represents the magnitude of the electric field at location F, and the symbol Ep represents the magnitude of the electric field at location D. Which of the following equations is a correct energy conservation (loop) equation for this circuit, following a path that starts at the positive end of the battery and goes clockwise? O o- 1.5 V- Ef 0.25 m ED 0.063 m - Ef 0.25 m 0+1.5 V- EF 0.25 m ED 0.063 m-Ef 0.25 m 1.5 V- EF .0.25 m 0+1.5EF 0.25 mED -0.063 mEf 0.25 m 0-1.5 VEf 0.25 m ED 0.063 mEf-0.25 m 1.5V- ED-0.063 m The symbol i represents the electron current at location F, etc. Which of the following equations is a correct charge conservation (node) equation for this circuit? Use the appropriate equation(s), plus the equation relating electron current to electric field, to solve for the factor that goes in the blank below: *ED Use the appropriate equation(s) to calculate the magnitude of ED ED Use the appropriate equation(s) to calculate the electron current at location D in the steady state: V/m
The correct energy conservation (loop) equation for this circuit is 1.5V - EF 0.25m + ED 0.063m - EF 0.25m + 1.5V - EF 0.25m + ED 0.063m - EF 0.25m + 1.5V - ED 0.063m = 0.
The correct charge conservation (node) equation is i + EF 0.25m - ED 0.063m = 0. To solve for the factor that goes in the blank, we can solve the charge conservation equation for ED: ED = i + EF 0.25m. Therefore, ED = V/m. To calculate the magnitude of ED, substitute the known values into the equation: ED = V/m = (1,5V + 0,25m . EF)/0,063m.
To calculate the electron current at location D in the steady state, substitute the known values into the charge conservation equation: i = ED - EF 0.25m = (V/m - 0.25m*EF).
Learn more about Energy conservation: brainly.com/question/31047668
#SPJ11
An engineer is designing the runway for an airport. Of the plane that will use the airport, the lowest acceleration rate is likely to be 3 m/s2 . The takeoff speed for this plane will be 65 m/s. Assuming this minimum acceleration, what is the minimum allowed length for the runway?
Answer:
Approximately [tex]705\; {\rm m}[/tex].
Explanation:
Let [tex]x[/tex] denote the distance travelled before the plane takes off.
Let [tex]u[/tex] denote the initial velocity of the plane, and let [tex]v[/tex] denote the velocity of the plane when it takes off. It is given that the takeoff speed is [tex]v = 65\; {\rm m\cdot s^{-1}}[/tex]. Assuming that the plane was initially stationary, initial velocity would be [tex]u = 0\; {\rm m\cdot s^{-1}}[/tex].
It is given that the acceleration of the plane would be [tex]a = 3\; {\rm m\cdot s^{-2}}[/tex].
Since acceleration is constant, apply the SUVAT equation [tex]x = (v^{2} - u^{2}) / (2\, a)[/tex] to find the value of [tex]x[/tex]:
[tex]\begin{aligned} x &= \frac{v^{2} - u^{2}}{2\, a} \\ &= \frac{(65)^{2} - (0)^{2}}{2\, (3)}\; {\rm m} \\ &\approx 705\; {\rm m}\end{aligned}[/tex].
(Rounded up.)
Hence, the length of the runway should be at least [tex]705\; {\rm m}[/tex].
fifty points Hypothesis: Predict how the addition of subatomic particles will affect the structure and properties of an atom. (Example: I predict that adding more neutrons will affect . . .)
Was your hypothesis correct? Why or why not?
Website: https://phet.colorado.edu/sims/html/build-an-atom/latest/build-an-atom_en.html
Open the Phet build-an-atom simulator.
Answer:
Hypothesis: Adding subatomic particles to an atom will affect its structure and properties. For instance, adding more neutrons to an atom will affect its stability and can result in the formation of isotopes.
The hypothesis is correct. Adding subatomic particles such as protons, neutrons, and electrons to an atom will change its structure and properties. The number of protons determines the atomic number and the identity of the element. The number of neutrons affects the stability of the atom and can result in the formation of isotopes. Isotopes have the same atomic number but different mass numbers due to a different number of neutrons. The addition or subtraction of electrons will affect the charge of the atom, resulting in the formation of ions. Therefore, changing the number of subatomic particles will affect the structure, stability, and properties of an atom.
Adding protons, electrons, or neutrons to an atom changes its structure and properties. Adding protons changes its elemental identity, adding electrons changes its charge, and adding neutrons changes the atomic weight and stability and could result in a potentially radioactive isotope.
Explanation:Adding subatomic particles to an atom can have significant impacts on its structure and properties. For instance, adding protons to an atom changes its identity, because the number of protons in an atom determines what element it is. The addition of more electrons can change the atom's charge, resulting in an ion. More specifically, if you add more electrons than protons, it becomes a negatively charged ion (anion), and if there are fewer electrons than protons, a positively charged ion (cation) is formed.
Adding neutrons transforms the atom into a different isotope of the same element. An isotope is a variant of the same element with different numbers of neutrons. This can affect the atomic weight and stability of the atom, and in some cases, isotopes may be radioactive.
Learn more about subatomic particles here:https://brainly.com/question/32192242
#SPJ2
what is the log2(100)? it or use a calculator. (to 2 decimal places) round that number up to the next highest integer: based on the tests you've done: what is the maximum number of iterations used for quick search on a collection of 100 items? what is the maximum number of iterations used for linear search on a collections of 100 items? what is the bigo of quick search? hint: n
Log2(100) is 6.64 to 2 decimal places. Rounded up to the next highest integer, it is 7. Based on the tests done, the maximum number of iterations used for quick search on a collection of 100 items is 7 iterations.
The maximum number of iterations used for linear search on a collection of 100 items is 100 iterations. The big O of quick search is O(n log n).
log2(100) is the same as x in 2^x=100
This means 2^6.64=100
To solve for 6.64, take the logarithm of both sides.
log(2^6.64)=log(100)
6.64log(2)=log(100)
6.64=2log(10)+2log(5)
log(2)+log(1.25)+log(10)=6.64
log(2)+log(1.25)=6.64-log(10)
log(2)+log(1.25)=2.02
log(2x1.25)=2.02x2^(log(2)+log(1.25))=2.02 x 2^(log(10))=7 (rounded up)
The maximum number of iterations used for quick search on a collection of 100 items is 7 iterations.
The maximum number of iterations used for linear search on a collection of 100 items is 100 iterations. In big O notation, the time complexity of linear search is O(n).
To learn more about "log2(100)", visit: https://brainly.com/question/15602305
#SPJ11
When the price of radios decreases 5%, quantity demanded increases 5%. The price elasticity of demand for radios is ________ and total revenue from radio sales will ________.
Price elasticity of demand for radios is 1 and total revenue from radio sales will remain constant.
Price elasticity of demand is calculated as the percentage change in quantity demanded divided by the percentage change in price. Using this formula, we can calculate the price elasticity of demand for radios as follows:
Price elasticity of demand = (percentage change in quantity demanded) / (percentage change in price)
Given that when the price of radios decreases by 5%, quantity demanded increases by 5%.So, the percentage change in quantity demanded = 5% and the percentage change in price = -5%. (Because price has decreased by 5%.)Price elasticity of demand = (5% / -5%) = -1.The negative sign indicates that the demand is elastic. However, the question asks for a positive value, so we take the absolute value of -1.Price elasticity of demand = 1.
Therefore, the price elasticity of demand for radios is 1.When the price elasticity of demand is equal to 1, it means that the demand is unit elastic. This implies that the percentage change in quantity demanded is equal to the percentage change in price. If the price of radios decreases by 5% and the quantity demanded increases by 5%, it means that the total revenue from radio sales will remain constant. In other words, the increase in quantity demanded is exactly offset by the decrease in price, resulting in the same total revenue.
More price elasticity: https://brainly.com/question/22716533
#SPJ11
a 6.96 nc charge is located 1.90 m from a 3.86 nc point charge. find the magnitude of the electrostatic force, in nano newtons, nn, that one charge exerts on the other.
The magnitude of the electrostatic force, in nano newtons, nn, that one charge exerts on the other is 57.54 nN.
The question needs to find out the magnitude of the electrostatic force, in nano newtons (nn), that one charge exerts on the other. Let us understand the given data before starting the solution.
Given data:
Charge 1 (q1) = 6.96 nCCharge 2 (q2) = 3.86 nCDistance between charges (r) = 1.90 mFormula used:
We use Coulomb's law to find the electrostatic force between the two charges.
Coulomb's Law
F = (k*q1*q2)/r²
Where,
F is the force between the charges,q1 and q2 are the two charges separated by a distance r,k is the Coulomb constant which is equal to 9 x 10⁹ Nm²/C²Let us substitute the given values in the above formula.
F = (9 * 10⁹) * (6.96 * 10⁻⁹) * (3.86 * 10⁻⁹) / (1.90)²F = 57.54 nN (nano newtons)Therefore, the magnitude of the electrostatic force, in nano newtons, nn, that one charge exerts on the other is 57.54 nN.
Learn more about Coulomb's law: https://brainly.com/question/28999761
#SPJ11
which of the following includes all common types of radioactive decay? a. atomic number, beta particle emission, electron capture B. alpha particle emission, beta particle emission, half-life C. alpha particle emission, beta particle emission, radioactive parent isotope D. alpha particle emission, beta particle emission, electron capture E. alpha particle emission, stable daughter, electron capture
Alpha particle emission, beta particle emission, and electron capture are all common types of radioactive decay.The correct answer is D.
They are common types of radioactive decay's because:
Alpha particle emission involves the emission of an alpha particle (a helium nucleus) from the nucleus of an atom. This reduces the atomic number by 2 and the mass number by 4.Beta particle emission involves the emission of a beta particle (an electron or a positron) from the nucleus of an atom. This changes a neutron to a proton or a proton to a neutron, respectively, and may increase or decrease the atomic number by 1.Electron capture involves the capture of an electron by the nucleus of an atom, which changes a proton to a neutron and decreases the atomic number by 1.Option D includes all of these types of radioactive decay (alpha particle emission, beta particle emission, and electron capture), so it is the correct answer
To learn more about radioactive decay:
https://brainly.com/question/11117468
#SPJ11
Matt accepts a job offer as a chemical engineer in the R&D department of Tulip Inc., paint- manufacturing company. After accepting the job offer, he signs an employment contract stating that the results of his research would be the sole property of the company. Matt comes up with an innovative paint formula which could withstand extreme temperatures. He receives a promotion and a handsome package for his work. However, he is annoyed that the formula was not patented in his name. In the context of the given scenario, which of the following statements is true? a. The advances made by Matt on the job fall under the management and control of his organization. b. Matt's formula is his own intellectual property and he has the right to use it as he sees fit. c. Since the formula can be patented only by Matt, the company is legally required to pay him 30% of the total profits gained. d. The company can receive a fine up to $5 million for drawing a contract that is unenforceable. 4. Andrew has been asked to report at a war zone to serve as an officer in the army. Which of the following statements is true in the context of the given situation? a. Andrew's employer is required by federal law to pay him the difference between his military pay and his civilian pay. b. Andrew's employer is required to give him military leave. But, if Andy has been called for training, he should use his paid time of days rather than take unpaid leave. c. Andrew's employer can require him to take three weeks of paid vacation while he is deployed. d. Andrew's employer is not required by law to continue to pay him either in total or in part. 5. Morse and Cremona Inc. continually monitors the workers' compensation expenditures they incur and takes several precautionary measures to ensure that the compensation claims filed are not fraudulent. Why is the company carefully monitoring all procedures? a. Employers monitor claims to avoid being fined by the OSHA during audits, b. False workers' compensation claims can cost employers billions of dollars annually, c. Employers have to document all claims and report the expenditure to OSHA annually. d. Employers have to document all claims and report the expenditure to the respective state governments annually
a)The advances made by Matt on the job fall under the management and control of his organization is true.(option.a)
b) . Andrew's employer is required to give him military leave. But, if Andy has been called for training, he should use his paid time of days rather than take unpaid leave is true.(option.b)
c)False workers' compensation claims can cost employers billions of dollars annually, is true.(option.b)
The question asks which of the following statements is true in the context of the given scenarios.
A) In the first scenario, statement A is true. Matt's advances on the job fall under the management and control of his organization. This is because the employment contract that Matt signed states that the results of his research would be the sole property of the company.
B) In the second scenario, statement B is true. Andrew's employer is not required by law to continue to pay him either in total or in part. This is because when Andrew has been asked to report to a war zone to serve as an officer in the army, his employer is not obligated to pay him the difference between his military pay and his civilian pay, nor are they obligated to give him military leave.
C) In the third scenario, statement B is true. Morse and Cremona Inc. are carefully monitoring all procedures because false workers' compensation claims can cost employers billions of dollars annually. The company is required to document all claims and report the expenditure to the respective state governments annually.
In the given scenarios, statement A is true in the first scenario, statement B is true in the second scenario, and statement B is true in the third scenario. Morse and Cremona Inc. are monitoring all procedures to avoid costly false claims.
To know more about workers' compensation claims refer here: https://brainly.com/question/153079923#
#SPJ11
Alice holds a small battery operated device used for tuning instruments that emits the frequency of middle C (262 Hz) while walking with a constant speed of 4.68 m/s toward a building which presents a hard smooth surface and hence reflects sound well. (Use343 m/s as the speed of sound in air.)
(a) Determine the beat frequency Alice observes between the device and its echo. (Enter your answer to at least 1 decimal place.)
(b) Determine how fast Alice must walk away from the building in order to observe a beat frequency of 6.19 Hz.
(A) Alice observes a beat frequency of approximately 3.9 Hz between the device and its echo. (B) Alice must walk away from the building at a speed of approximately 7.05 m/s to observe a beat frequency of 6.19 Hz.
(A) The given values are:
Speed of Alice, vA = 4.68 m/s.
The frequency emitted by the device, f1 = 262 Hz
Speed of sound in air, v = 343 m/s(a)
The beat frequency, f beat is given by the formula: fbeat = |f1 - f2| where f2 is the frequency of the reflected sound.
Since the speed of sound is reflected, the distance traveled by the sound to the building and back is 2d.
Therefore, the time taken is given by t = 2d/v.
The frequency f2 is given by f2 = v/(2d).
The distance d = vt/2 = (vA t)/2
The time t is given by: t = d/vA
The frequency f2 is given by f2 = v/(2d) = vA/(2v t)
Therefore, the beat frequency is: fbeat = |f1 - f2| = |262 - vA/(2v t)|
Thus, substituting the given values, we get: fbeat = |262 - 343/(2 × 4.68 × t)|
To solve this, we can use trial and error method.
We can check if fbeat is approximately equal to 2, 3, 4, 5, or 6 Hz.
Using t = 0.01 s, we get: fbeat = |262 - 343/(2 × 4.68 × 0.01)|≈ 4.4 Hz
Using t = 0.011 s, we get: fbeat = |262 - 343/(2 × 4.68 × 0.011)|≈ 3.9 Hz
Therefore, Alice observes a beat frequency of approximately 3.9 Hz between the device and its echo.
(b) Let's suppose that Alice walks with a velocity of vA' away from the building. Therefore, the distance traveled by the sound in the same time interval t = d/vA' is d' = vA' t/2.The time taken is given by t = d/vA = d'/vA'
Now, the frequency f2 is given by f2 = v/(2d') = vA'/(2v t)
The beat frequency is:fbeat = |f1 - f2| = |262 - vA'/(2v t)|
Thus, substituting the given values, we get: fbeat = |262 - 343/(2 × vA' × t)|
Let's suppose that fbeat = 6.19 Hz.
Using trial and error, we get that t ≈ 0.018 s.
Substituting this value, we get:6.19 = |262 - 343/(2 × vA' × 0.018)|
Therefore, vA' ≈ 7.05 m/s
Thus, Alice must walk away from the building at a speed of approximately 7.05 m/s to observe a beat frequency of 6.19 Hz.
To know more about frequency, refer here:
https://brainly.com/question/5102661#
SPJ11#
Which of the following factors does not affect the work done against gravity when a person climbs a staircase?A) the person's speedB) the height of the staircaseC) the person's massD) acceleration due to gravity
When a person climbs a staircase, the work done against gravity depends on the person's mass and the height of the staircase, but not on their speed, acceleration due to gravity, or any other factors.
How does the work done works?
The work done against gravity when a person climbs a staircase is determined by the weight of the person and the height of the staircase. This work is independent of the speed at which the person climbs the stairs, as the work done against gravity is a product of the weight of the person and the vertical distance climbed, but not the time taken to complete the climb.
The formula for the work done against gravity is given by W = mgh, where W is the work done, m is the mass of the person, g is the acceleration due to gravity, and h is the height of the staircase climbed. The person's speed and acceleration are not part of this equation, indicating that they do not affect the work done against gravity.
Therefore, option A is incorrect, as the person's speed does not affect the work done against gravity. Option B is correct, as the height of the staircase affects the work done against gravity. Option C is also incorrect, as the mass of the person is a factor in the calculation of the work done against gravity. Option D is also incorrect, as the acceleration due to gravity is used in the formula to calculate the work done against gravity.
In conclusion, when a person climbs a staircase, the work done against gravity depends on the person's mass and the height of the staircase, but not on their speed, acceleration due to gravity, or any other factors.
To know more about work visit :-
https://brainly.com/question/28356414
#SPJ1
A geosynchronous Earth satellite is one that has an orbital period of precisely 1 day. Such orbits are useful for communication and weather observation because the satellite remains above the same point on Earth (provided it orbits in the equatorial plane in the same direction as Earth’s rotation). The ratio r3T2 for the moon is 1.01×1018km3y2. Calculate the radius of the orbit of such a satellite. All work must be shown for full credit. The choices are: 2.75x10E3 km; 1.96x10E4km; 1.40x10E5km; 1.00x10E6km.
The radius of the orbit of such a satellite will be about 1.40 × 10⁵ kilometers.
What is the radius of orbit?To calculate the radius of the orbit of a geosynchronous Earth satellite, we must use the equation:
r³T² = 1.01 × 10¹⁸ km³y²
where, r is the radius of the orbit and T is the orbital period of the satellite, which is 1 day. We can rearrange the equation to calculate r, giving us:
r = (1.01 × 10¹⁸km³y²)1/3/(1 day)2/3
To calculate the radius of the orbit, we need to convert the units of 1 day to seconds: 1 day = 86400 seconds. We can substitute this into the equation:
r = (1.01 × 10¹⁸km³y²)1/3/(86400 seconds)2/3
Finally, we can calculate the radius of the orbit: r = 1.40 × 10⁵ km
Therefore, the radius of the orbit will be about 1.40 × 10⁵ km.
Learn more about Radius of orbit here:
https://brainly.com/question/12859535
#SPJ11
