Answer:
7505.19 J
Explanation:
We'll begin by calculating the change in the temperature of copper. This can be obtained as follow:
Initial temperature (T₁) = 20 °C
Final temperature (T₂) = 875 °C
Change in temperature (ΔT) =?
ΔT = T₂ – T₁
ΔT = 875 – 20
ΔT = 855 °C
Finally, we shall determine the heat required. This can be obtained as follow:
Specific heat capacity (C) = 0.385 J/gºC
Change in temperature (ΔT) = 855 °C
Mass (M) = 22.8 g
Heat (Q) required =?
Q = MCΔT
Q = 22.8 × 0.385 × 855
Q = 7505.19 J
Thus, 7505.19 J of heat energy is required.
g Select the statement that best answers the following question What effect does the cation of an ionic compound have on the appearance of the solution? The cation affects the intensity of the color more than the color of the solution. The cation affects the color of the solution more than the intensity of the color. The cation does not affect the color or color intensity of the solution. The cation only affects the intensity of the color in a solution.
Answer:
The cation affects the intensity of the color more than the color of the solution.
Explanation:
According to Beer Lambert law, the intensity of the colour of the solution depends on the concentration of the specie responsible for the colour in the solution.
Let us recall that transition metal compounds are coloured in solution due to electronic transitions.
Therefore, the cation affects the intensity of the color more than the color of the solution.
Question:
What is the molar concentration of 1.29 mol of KCL dissolved in 350 mL of solution?
Answer:
M = 3.69 M.
Explanation:
Hello there!
In this case, according to the given information, it turns out possible for us to calculate the molar concentration of the 1.29 moles of KCl in 350 mL of solution by recalling the mathematical definition of molarity as the division of the moles by the volume in liters, in this case 0.350 L; thus, we proceed as follows:
[tex]M=\frac{1.29mol}{0.350L}\\\\M=3.69M[/tex]
Which gives molar units, M, or just mol/L.
Regards!
Share the same molecular formula but have different connectivity of atoms and different physical properties.
Answer:
Constitutional Isomers
Explanation:
Constitutional isomers can be regarded as structural isomers ,these are compounds that have the same molecular formula with different structural formulas. Example is Butane and isobutane; both compound posses the same molecular formula(C4H10) with different structural formulas. compounds of Constitutional isomers are differ in term of connectivity, which
is the way the constituent atoms are been connected to another. It should be noted that Constitutional Isomers Share the same molecular formula but have different connectivity of atoms and different physical properties.
Using the formation of formaldehyde as a model, comment on photosynthesis and the formation of sugars using what we know about entropy and free energy.
Answer:
It produces free energy.
Explanation:
Photosynthesis is a process which is used by the plant for producing energy in the form of ATP. This energy is used by the plants in different activities which enables the plant to grow and develop successfully. There are some factors which causes change in the rate of photosynthesis means the production of energy for the plant body. If the environmental factors are suitable, more energy is produced through the process of photosynthesis.
Nitric acid (HNO3) reacts with ammonia (NH3) in aqueous solution. Use your knowledge of nitric acid to decide what type of reaction arrow(s) to use. $$ Part 2 (1 point) Sulfuric acid (H2SO4) reacts with ammonia in aqueous solution. Use your knowledge of sulfuric acid to decide what type of reaction arrow(s) to use. $$
Answer:
Both reactions are acid-base reactions
Explanation:
An acid base reaction is a reaction that occurs between an acid and a base. This reaction often leads to the formation of a salt in the process. The nature of the salt depends on the type of acid and base that reacted in the process.
Both HNO3 and H2SO4 are strong acids. However, ammonia is a weak base. The acid base reaction between ammonia and these strong acids is shown below;
HNO3(aq) + NH3(aq) ------>NH4NO3(aq)
H2SO4(aq) + 2NH3(aq) ----> (NH4)2SO4(aq)
cuáles son las características de la luz y en qué consisten
Answer:
Cuáles son las características de la luz y en qué consisten?
Explanation:
La luz es una radiación que se propaga en forma de ondas. Las ondas que se pueden propagar en el vacío se llaman ONDAS ELECTROMAGNÉTICAS. La luz es una radiación electromagnética
In the reaction represented by the equation: N2 + 3H2 → 2NH3, what is the conversion factor of nitrogen to ammonia? Explain by using law of definite proportion
Answer:
10/3
Explanation:
Hope this helps
Answer:
The compound formula for the ammonia is
N
H
3
. It is a colorless gas. It is the result of the chemical reaction between nitrogen and hydrogen gas. The chemical reaction between the gases is shown below:
N
2
+
3
H
2
→
2
N
H
3
Chrysanthenone is an unsaturated ketone. If Chrysanthenone has M+ = 150 and contains 2 double bond(s) and 2 ring(s); what is its molecular formula? Enter the formula in the form CH first, then all other atoms in alphabetical order; do not use subscripts. The formula is case-sensitive.
Answer:
the Molecular formula will be; C10H14O
Explanation:
Given the data in the question;
Chrysanthenone is an unsaturated ketone,
it has M+ = 150 and contains 2 double bond(s) and 2 ring(s).
molecular formula = ?
we know that ketone contain 1 oxygen and mass of oxygen is 16
so mass of the C and H remaining will be;
⇒ 150 - 16 = 134
Now we determine the number of C atoms;
⇒ 134 / 13 = 10
hydrocarbon with 10 hydrogen atom have CnH2n+2 means
⇒ ( 10 × 2 ) +2 = 22 hydrogens
But then we have 3 unsaturation meaning 6 hydrogens less and also we have ring meaning 2 more hydrogens
⇒ 22 - 6 - 2 = 14
Hence the Molecular formula will be; C10H14O
What should the coefficient for the diatomic oxygen (O2) be when this equation is correctly balanced
3
And then for Fe it should be 4 and for the products it should be 2!!
8. What does the term 'sustainable mean? *
Answer:
something that can be maintained over a period of time
Answer:
a balance between meeting today's needs.......
Explanation:
HELPP
There are 9.23 x 1023 molecules of water in a beaker, how many moles are there?
Answer:
Answer: There are 1.53 moles present in molecules of water in a beaker.
Explanation:
According to the mole concept, there are molecules present in 1 mole of a substance.
So, number of moles present in molecules are calculated as follows.
Thus, we can conclude that there are 1.53 moles present in molecules of water in a beaker.
Explanation:
50.0 g of Potassium chloride reacts with 50.0 g of oxygen to produce KCIO3. After writing
and balancing the reaction, determine the amount of potassium chlorate produced
128 g
32.0 g
082.2 g
None of these answers.
Explanation:
If 50.0 grams of Zinc are reacted with 50.0 grams of Hydrogen Chloride ... 50.09 Zn x 1 mol Zn , Imol ZnCl2 , 136.4g. ... If a decomposition reaction produces a 75.0% yield for the oxygen by mass (128.0 grams were.
Part C
Read about an improved version of an atmospheric water generator e, and write a
one-paragraph description of this technology.
Answer:
Atmospheric water generator is used in regions that have scarcity of water or have polluted water. These generators are reliable sources of clean and safe water and hence reduces dependency on bottled water.
Atmospheric water generator extract water from the air (humid air) through condensation. Extracted water then cools down to temperature below its dew point thereby producing potable drinking water.
Explanation:
Atmospheric water generator is used in regions that have scarcity of water or have polluted water. These generators are reliable sources of clean and safe water and hence reduces dependency on bottled water.
Atmospheric water generator extract water from the air (humid air) through condensation. Extracted water then cools down to temperature below its dew point thereby producing potable drinking water.
Answer:
A device that collects water from humid ambient air is known as an atmospheric water generator. Condensation is the process of extracting water vapor from the air by chilling it below its dew point, exposing it to desiccants, or pressurizing it. An AWG, unlike a dehumidifier, is meant to make the water drinkable. Because there is nearly always a little amount of water in the air that may be collected, AWGs are useful in situations where clean drinking water is difficult or impossible to get. Cooling and desiccants are the two most common ways used.
Explanation:
calculate the mass in 4.05*10^22 molecules of calcium phosphate
Answer:
m = 20.9 g.
Explanation:
Hello there!
In this case, according to the given information, it turns out possible for us to solve this problem by recalling both the Avogadro's number for the calculation of the moles in the given molecules of calcium phosphate and the molar mass of this compound in order to secondly calculate the mass as shown on the following setup:
[tex]m=4.05x10^{22}molecules*\frac{1mol}{6.022x10^{23}}*\frac{310.18g}{1mol}\\\\m=20.9g[/tex]
Regards!
What are the characteristics of ionic compounds?
Answer:
the characteristics of ionic compounds are :
1.They form crystals.
2.They are hard and brittle.
Answer:
they form crystals.
they have high melting and boiling points.
they are hard and brittle.
they are good insulators.
when dissolve in water...they dissociate Into ions.
NO2 (nitrogen dioxide) is a Greenhouse Gas that can be produced in car engines. The average diesel truck produces 80g of NO2 for every 1000 kilometers it drives. How many moles of NO2 are in 80g of NO2?
Answer:
[tex]1.74molNO_2[/tex]
Explanation:
Hello there!
In this case, according to the given information, it turns out possible for us to perform mole-mass relationships by using the molar mass of the involved substance, in this case NO2, which is 46.0 g/mol; then we just set up a conversion factor like the one shown below:
[tex]80g*\frac{1mol}{46g}\\\\1.74molNO_2[/tex]
Regards!
What is the pH of 0.6 M NaOH?
Answer:
pOH = - log[OH-]
[OH-] = 0.6M
[tex]pOH \: = - log(0.6) \\ = 0.2218487496 \\ pH \: + pOH \: = 14 \\ pH \: + 0.221848749 = 14 \\ pH = 14 - 0.221848749 \\ = 13.77815125 \\ 13.8[/tex]
What is the right answer?
Answer:
equal to zero is the right answer
When heated, magnesium combines readily with excess oxygen in the air to produce magnesium oxide, as shown in the following unbalanced equation.
Mg (s) + O2 (g) → MgO (s) + heat
What two types of reactions could this chemical equation be classified as?
Answer: The given chemical reaction can be classified as synthesis and exothermic.
Explanation:
A synthesis reaction is defined as the reaction where two small chemical species combine in their elemental state to form a single large chemical species.
Exothermic reactions are defined as the reactions in which heat is released by the reaction. The heat is written on the product side of the reaction.
For the given chemical reaction:
[tex]Mg(s)+O_2(g)\rightarrow MgO(s)+\text{heat}[/tex]
The above chemical reaction is a type of synthesis and exothermic as two substances in their elemental state are combining. Also, heat is getting released in the reaction.
Hence, the given chemical reaction can be classified as synthesis and exothermic.
Write the empirical formula for at least four ionic compounds that could be formed from the following ions:
a). PO3−4
b). NH+4
c). Fe3+
d). ClO−3
Answer:
a. Na₃PO₄
b. NH₄Cl
c. FeCl₃
d. KClO₃
Explanation:
a. Sodium tetraoxophosphate(V) Na₃PO₄
3Na⁺ + PO₄³⁻ → Na₃PO₄
b. Ammonium Chloride NH₄Cl
NH₄⁺ + Cl⁻ → NH₄Cl
c. Iron(III)chloride
Fe³⁺ + Cl⁻ → FeCl₃
d. Potassium trioxochlorate(V) KClO₃
K⁺ + ClO₃⁻ → KClO₃
cấu hình electron của nguyên tử Ca
Explanation:
Do đó cấu hình electron của canxi là: 1s2 2s2 2p6 3s2 3p6 4s2.
The human body contains many elements from the periodic table. It is mostly composed of oxygen and carbon, but trace
elements also have a significant role. The table gives the mass, in kilograms, of some elements found in the human body, based
on a 70.0 kg person.
Atomic number
Element
Mass (kg)
8
oxygen
45.2
6
carbon
12.6
1
hydrogen
7.0
7
nitrogen
2.2
20
calcium
1.3
15
phosphorus
0.78
19
potassium
0.25
16
sulfur
0.18
others
0.60
total
70,0
Potassium makes up what fraction of the mass of the human body?
From the question given above, the following data were obtained:
Oxygen = 45.2 Kg
Carbon = 12.6 Kg
Hydrogen = 7 Kg
Nitrogen = 2 Kg
Calcium = 1.3 Kg
Phosphorus = 0.78 Kg
Potassium = 0.25 Kg
Sulphur = 0.18 Kg
Others = 0.60 Kg
Total = 70 Kg
Fraction of potassium =?We can obtain the fraction of potassium of the mass of the body as follow:
Potassium = 0.25 Kg
Total = 70 Kg
Fraction of potassium =?Fraction of potassium = mass of potassium / Total
Fraction of potassium = 0.25 / 70
Fraction of potassium = 1/280Therefore, the fraction of potassium in the body is 1/280
Learn more: https://brainly.com/question/14760859
Choose the compound that exhibits hydrogen bonding as its strongest intermolecular force. Choose the compound that exhibits hydrogen bonding as its strongest intermolecular force. CH2Br2 CH3NH2 LiF C3H8 CF4
Answer:
The given molecules are:
CH2Br2
CH3NH2
LiF
C3H8
CF4.
Which compound consists of the hydrogen bond as the strongest intermolecular force.
Explanation:
The hydrogen bond is the electrostatic force of attraction that exists between the covalently bonded H-atom of one molecule and a high electronegative atom (N, O, F) of another molecule.
For example, H-bonding in water is represented below:
Among the given molecules,
CH2Br2 does not have H-bond because there is no either N or O or F atom in it.
In LiF also there is no H-atom and no hydrogen bond.
C3H8 also does not have H-bond in it.
CF4 also does not have H-atom or hydrogen bond in it.
The answer is CH3NH2(methylamine).
It has an intermolecular hydrogen bond in it as shown in the attachment.
The dashed line represents the H-bond.
To determine the freezing point depression of a LiCl solution, Toni adds 0.411 g of LiCl to the sample test tube along with 19.7 mL of distilled water. Determine the molal concentration (m) of the resulting solution. MWLiCl
Answer:
LiCl = 0.492 m
Explanation:
Molal concentration is the one that indicates the moles of solute that are contained in 1kg of solvent.
Our solute is lithium chloride, LiCl.
Our solvent is distilled water.
We do not have the mass of water, but we know the volume, so we should apply density to determine mass.
Density = mass / volume
Density . volume = mass
1 g/mL . 19.7 mL = 19.7 g
We convert g to kg → 19.7 g . 1 kg / 1000g = 0.0197 kg
Let's determine the moles of LiCl
0.411 g . 1 mol / 42.394 g = 9.69×10⁻³ moles
Molal concentration (m) = 9.69×10⁻³ mol / 0.0197 kg → 0.492 m
The molal concentration of the resulting solution is 0.492 m. The concentration number of moles of solute in one kg of solvent.
What is Molal concentration?It is the measure of the concentration number of moles of solute in one kg of solvent.
To calculate the molal concentration first calculated the mass of [tex]\bold {LiCl}[/tex],
[tex]\rm \ mass = density \times volume[/tex]
Put the values,
m = 1 g/mL x 19.7 mL
m = 19.7 g or
m = 0.0197 kg
Calculate the moles of LiCl:
[tex]n =\rm \dfrac { 0.411 \ g \times 1 mol }{ 42.394 \ g }\\\\n = 9.69\times 10^{-3} \ moles[/tex]
So, now the molal concentration,
[tex]m = \rm \dfrac { 9.69\times 10^{-3}\ mol} {0.0197 \ kg} \\\\m = 0.492[/tex]
Therefore, the molal concentration of the resulting solution is 0.492 m.
Learn more about molal concentration:
https://brainly.com/question/4580605
A student is examining a chemical reaction the student notes that the reaction requires 7.14 kcal mol energy per biomlecule synthesized the reaction itself produces 21.42 kcal mol energy the sutdent argues this is enough energy to make 3 biomecules. What error has the student made in the analysis?
a. The studentiras not remembered the Second Law of Thermodynamics.
b. The students has not remembered the First Law of Thermodynamics.
c. The student has made a simple calculation error
d. The student has made a conversion error
why is tin tin and aluminum the better choice for canned milk
Answer:
Well, they are very durable unlike other packaging food materials, they can be recycled. But, the internet says allumninum cans are much better. and it could be better because you can keep the canned milk cool (cold) for a long lasting time. (keep it in the fridge if you want it to stay cold even longer)
What is the correct answer question
Answer:
B
Explanation:
A substance with two oxygen atoms is combined with a substance with one oxygen atom to form one product. What is true of the product?
There will be no oxygen in the product. Some of the oxygen will evaporate into the air.
Which of the following is not a polymer
A. Glucose.
B. Starch.
C. Cellulose.
D. DNA.
Answer:
A. Glucose
Explanation:
Glucose is a monomer and not a polymer. So, option (A) is not a polymer.
Glucose is not a polymer because it is a kind of molecule while Starch , cellulose and DNA are polymers.
The correct answer is option A. Glucose.
Calculate the number of milliliters of 0.587 M NaOH required to precipitate all of the Fe3 ions in 197 mL of 0.654 M FeCl3 solution as Fe(OH)3. The equation for the reaction is: FeCl3(aq) 3NaOH(aq) Fe(OH)3(s) 3NaCl(aq)
Answer: The number of milliliters of 654 mL for 0.587 M NaOH required to precipitate all of the [tex]Fe^{3+}[/tex] ions in 197 mL of 0.654 M [tex]FeCl_{3}[/tex] solution as [tex]Fe(OH)_{3}[/tex].
Explanation:
The reaction equation is as follows.
[tex]FeCl_{3}(aq) + 3NaOH(aq) \rightarrow Fe(OH)_{3}(s) + 3NaCl(aq)[/tex]
Therefore, moles of [tex]Fe(OH)_{3}[/tex] are calculated as follows.
Moles = Molarity of [tex]Fe(OH)_{3}[/tex] [tex]\times[/tex] Volume (in L)
= 0.654 M [tex]\times[/tex] 0.197 L
= 0.128 mol
Now, according to the given balanced equation 1 mole of [tex]FeCl_{3}(aq)[/tex] reacts with 3 moles of NaOH(aq). Hence, moles of [tex]Fe(OH)_{3}[/tex] reacted are calculated as follows.
3 [tex]\times[/tex] 0.128 mol = 0.384 moles of NaOH
As moles of NaOH present are as follows.
Moles of NaOH = Molarity of NaOH [tex]\times[/tex] Volume (in L)
0.384 mol = 0.587 M [tex]\times[/tex] Volume (in L)
Volume (in L) = 0.654 L (1 L = 1000 mL) = 654 mL
Thus, we can conclude that the number of milliliters of 654 mL for 0.587 M NaOH required to precipitate all of the [tex]Fe^{3+}[/tex] ions in 197 mL of 0.654 M [tex]FeCl_{3}[/tex] solution as [tex]Fe(OH)_{3}[/tex].
