g One of the harmonics in an open-closed tube has frequency of 500 Hz. The next harmonic has a frequency of 700 Hz. Assume that the speed of sound in this problem is 340 m/s. a. What is the length of the tube

Answers

Answer 1

Answer:

The length of the tube is 85 cm

Explanation:

Given;

speed of sound, v = 340 m/s

first harmonic of open-closed tube is given by;

N----->A , L= λ/₄

λ₁ = 4L

v = Fλ

F = v / λ

F₁ = v/4L

Second harmonic of open-closed tube is given by;

L = N-----N + N-----A, L = (³/₄)λ

[tex]\lambda = \frac{4L}{3}\\\\ F= \frac{v}{\lambda}\\\\F_2 = \frac{3v}{4L}[/tex]

Third harmonic of open-closed tube is given by;

L = N------N + N-----N + N-----A, L = (⁵/₄)λ

[tex]\lambda = \frac{4L}{5}\\\\ F= \frac{v}{\lambda}\\\\F_3 = \frac{5v}{4L}[/tex]

The difference between second harmonic and first harmonic;

[tex]F_2 -F_1 = \frac{3v}{4L} - \frac{v}{4L}\\\\F_2 -F_1 = \frac{2v}{4L} \\\\F_2 -F_1 =\frac{v}{2L}[/tex]

The difference between third harmonic and second harmonic;

[tex]F_3 -F_2 = \frac{5v}{4L} - \frac{3v}{4L}\\\\F_3 -F_2 = \frac{2v}{4L} \\\\F_3 -F_2 =\frac{v}{2L}[/tex]

Thus, the difference between successive harmonic of open-closed tube is

v / 2L.

[tex]700H_z- 500H_z= \frac{v}{2L} \\\\200 = \frac{v}{2L}\\\\L = \frac{v}{2*200} \\\\L = \frac{340}{2*200}\\\\L = 0.85 \ m\\\\L = 85 \ cm[/tex]

Therefore, the length of the tube is 85 cm


Related Questions

A golfer hits a 42 g ball, which comes down on a tree root and bounces straight up with an initial speed of 15.6 m/s. Determine the height the ball will rise after the bounce. Show all your work.

Answers

Answer:

12.2 m

Explanation:

Given:

v₀ = 15.6 m/s

v = 0 m/s

a = -10 m/s²

Find: Δy

v² = v₀² + 2aΔy

(0 m/s)² = (15.6 m/s)² + 2 (-10 m/s²) Δy

Δy = 12.2 m

[tex] \LARGE{ \boxed{ \rm{ \green{Answer:}}}}[/tex]

Given,

The initial speed is 15.6 m/s The mass of the ball is 42g = 0.042kg

Finding the initial kinetic energy,

[tex]\large{ \boxed{ \rm{K.E. = \frac{1}{2}m {v}^{2}}}}[/tex]

⇛ KE = (1/2)mv²

⇛ KE = (1/2)(0.042)(15.6)²

⇛ KE = 5.11 J

|| ⚡By conservation of energy, the potential energy at the highest point will also be 5.11 J, since there is no kinetic energy at the highest point because the ball is not moving (we neglect energy lost due to air resistance, heat, sound, etc.) ⚡||

So, we have:

[tex] \large{ \boxed{ \rm{P.E. = mgh}}}[/tex]

⇛ h = PE/(mg)

⇛ h = 5.11 J /(0.042 × 9.8)

⇛ h = 12.41 m

✏The ball will rise upto a height of 12.41 m

━━━━━━━━━━━━━━━━━━━━

Which of the following explains why a “control” is important in a case-control study of a disease? The researchers need to control the bias that those who contracted the disease may create when they talk to others. The researchers need to compare those who contracted the disease to those who did not. The researchers need to compare those who contracted the disease to those who contracted previous diseases. The researchers need to control the disease so that it is not spread further.

Answers

The researchers need to compare those who contracted the disease to those who did not.

hi guys!!! i have no more points, can someone nice guess all of these for me? :)
1.What happens to the ocean water before the precipitation part of the water cycle
2.During which stage of the water cycle does water from the ocean form clouds?
3.what is a runoff??
4.Which statement about oceans is incorrect? A.Evaporation occurs when water is warmed by the sun. B.Most evaporation and precipitation occur over the ocean. C.97 percent of Earth's water is fresh water from the ocean. D.Water leaves the ocean by the process of evaporation
5.How does most ocean water return to the ocean in the water cycle

tysm to u who answers :)

Answers

1. The ocean water collects back in the ocean.

2. Condensation is the process by which water vapor in the air is changed into liquid water. Condensation is crucial to the water cycle because it is responsible for the formation of clouds.

3. an excessive amount of water flowing from downslope along earths surface

4. A.Evaporation occurs when water is warmed by the sun.

5. The water returns into the ocean by the water cycle . It evaporates , then it condensates , then it participates ( Rains ) and then goes back into the ocean.

Hope this answer correct ✌️

A baseball (m=145g) traveling 35 m/s moves a fielder's glove backward 23 cm when the ball is caught. What was the average force exerted by the ball on the glove?

Answers

Answer:

386.13 N

Explanation:

The kinetic energy of the baseball is converted into workdone in moving the glove backward( work energy theorem).

Therefore, KE of the ball

[tex]\frac{1}{2} mv^2 =\frac{1}{2}(0.145)35^2\\ = 88.81 \text{J}[/tex]

Now, workdone in moving the glove

W= Fd

where F = Force applied, d = displacement of the glove= 0.23 cm.

88.81 = F×0.23

F= 88.81/0.23 = 386.13 N

Determine the next possible thickness of the film (in nm) that will provide the proper destructive interference. The index of refraction of the glass is 1.58 and the index of refraction of the film material is 1.48.

Answers

Answer:

I know the answer

Explanation:

We want to choose the film thickness such that destructive interference occurs between the light reflected from the air-film interface (call it wave 1) and from the film-lens interface (call it wave 2). For destructive interference to occur, the phase difference between the two waves must be an odd multiple of half-wavelengths.

You can think of the phases of the two waves as second hands on a clock; as the light travels, the hands tick-tock around the clock. Consider the clocks on the two waves in question. As both waves travel to the air-film interface, their clocks both tick-tock the same time-no phase difference. When wave 1 is reflected from the air-film boundary, its clock is set forward 30 seconds; i.e., if the hand was pointing toward 12, it's now pointing toward 6. It's set forward because the index of refraction of air is smaller than that of the film.

Now wave 1 pauses while wave two goes into and out of the film. The clock on wave 2 continues to tick as it travels in the film-tick, tock, tick, tock.... Clock 2 is set forward 30 seconds when it hits the film-lens interface because the index of refraction of the film is smaller than that of the lens. Then as it travels back through the film, its clock still continues ticking. When wave 2 gets back to the air-film interface, the two waves continue side by side, both their clocks ticking; there is no change in phase as they continue on their merry way.

So, to recap, since both clocks were shifted forward at the two different interfaces, there was no net phase shift due to reflection. There was also no phase shift as the waves travelled into and out from the air-film interface. The only phase shift occured as clock 2 ticked inside the film.

Call the thickness of the film t. Then the total distance travelled by wave 2 inside the film is 2t, if we assume the light entered pretty much normal to the interface. This total distance should equal to half the wavelength of the light in the film (for the minimum condition; it could also be 3/2, 5/2, etc., but that wouldn't be the minimum thickness) since the hand of the clock makes one revolution for each distance of one wavelength the wave travels (right?).

If you wish to observe features that are around the size of atoms, say 5.5 × 10^-10 m, with electromagnetic radiation, the radiation must have a wavelength of about the size of the atom itself.


Required:

a. What is its frequency?

b. What type of electromagnetic radiation might this be?

Answers

Answer:

a) 5.5×10^17 Hz

b) visible light

Explanation:

Since the wavelength of the electromagnetic radiation must be about the size of the about itself, this implies that;

λ= 5.5 × 10^-10 m

Since;

c= λ f and c= 3×10^8 ms-1

f= c/λ

f= 3×10^8/5.5 × 10^-10

f= 5.5×10^17 Hz

The electromagnetic wave is visible light

If a convex lens were made out of very thin clear plastic filled with air, and were then placed underwater where n = 1.33 and where the lens would have an effective index of refraction n = 1, the lens would act in the same way
a. as a flat refracting surface between water and air as seen from the water side.
b. as a concave mirror in air.
c. as a concave lens in air.
d. as the glasses worn by a farsighted person.
e. as a convex lens in air.

Answers

Answer:

D. A convex lens in air

Explanation:

This is because the air tight plastic under water will reflect light rays in the same manner as a convex lens

In the lab, you shoot an electron towards the south. As it moves through a magnetic field, you observe the electron curving upward toward the roof of the lab. You deduce that the magnetic field must be pointing:_______.
a. to the west.
b. upward.
c. to the north.
d. to the east.
e. downward.

Answers

Answer:

a. to the west.

Explanation:

An electron in a magnetic field always experience a force that tends to change its direction of motion through the magnetic field. According to Lorentz left hand rule (which is the opposite of Lorentz right hand rule for a positive charge), the left hand is used to represent the motion of an electron in a magnetic field. Hold out the left hand with the fingers held out parallel to the palm, and the thumb held at right angle to the other fingers. If the thumb represents the motion of the electron though the field, and the other fingers represent the direction of the field, then the palm will push in the direction of the force on the particle.

In this case, if we point the thumb (which shows the direction we shot the electron) to the south (towards your body), with the palm (shows the direction of the force) facing up to the roof, then the fingers (the direction of the field) will point west.

Which is one criterion that materials of a technological design should meet? They must be imported. They must be affordable. They must be naturally made. They must be locally produced.

Answers

Answer:

they must be affordable because they have to pay for it or they wont get the stuff they are bying.

Explanation:

need a brainliest please.

Answer: B, they must be affordable.

Explanation:

Which of these cannot be a resistor in a series or parallel circuit?
A)switch
B) battery
C) light bulb
D) all of these are resistors

Answers

Answer:

it is going to D. all of these are resistors

an electron travels at 0.3037 times the speed of light through a magnetic field and feels a force of 1.2498 pN. What is the magnetic field in teslas

Answers

Answer:

Explanation:

Charge on an electron (q) = 1.6 * 10 ^ -19 C

Velocity of electron (v) = 0.3037 * 300,000,000 = 91,110,000 m/sec

We know that, Force exerted on moving particle moving through a magnetic field :

[tex]F= q * v * B ( q,v\ and\ B\ are\ mutually\ perpendicular)[/tex]

1.2498 * 10 ^ -12 = 1.6 * 10^ -19 * 91110000 * B

B =  0.08573 T

A fish is 80 cm below the surface of a pond. What is the apparent depth (in cm) when viewed from a position almost directly above the fish

Answers

Answer:

Apparent depth (Da) = 60.15 cm (Approx)

Explanation:

Given:

Distance from fish (D) = 80 cm

Find:

Apparent depth (Da)

Computation:

We know that,

Refractive index of water (n2) = 1.33

So,

Apparent depth (Da) = D(n1/n2)

Apparent depth (Da) = 80 (1/1.33)

Apparent depth (Da) = 60.15 cm (Approx)

The apparent depth of the fish is 60 cm.

To calculate the apparent depth of the fish, we use the formula below.

Formula:

R.F(water) = Real depth(D)/Apparent depth(D')R.F = D/D'.................... Equation 1

Where:

R.F = Refractive index of water

Make D' The subject of the equation.

D' = D/R.F................... Equation 2

From the question,

Given:

D = 80 cmR.F = 1.333

Substitute these values into equation 2

D' = 80/1.33D' = 60.01D' = 60 cm

Hence, the apparent depth of the fish is 60 cm

Learn more about apparent depth here: https://brainly.com/question/24319677

The power lines are at a high potential relative to the ground, so there is an electric field between the power lines and the ground. To maximize the potential difference between one end of the fluorescent tube and the other, how should the tube be held?a. The tube should be held horizontally, parallel to the ground b. The potential difference between the ends of the tube does not depend on the tube's orientation. c. The tube should be held vertically perpendicular to the ground

Answers

Answer:

b) True. potencial diferencie does not depend on orientation

Explanation:

In this exercise we are asked to show which statements are true.

The expression the potential with respect to earth or the electric field with respect to earth refers to the potential or electric charge of the planet that is assumed to be very large and does not change in value during work.

It does not refer to the height of the system.

We can now review the claims

a) False. Potential not to be refers to height

b) True. Does not depend on orientation

c) False The potential does not refer to the altitude but to the Earth's charge

(a) Determine the capacitance of a Teflon-filled parallel-plate capacitor having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.


pF

(b) Determine the maximum potential difference that can be applied to a Teflon-filled parallel-plate capacitor having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.
kV

Answers

Explanation:

(a) Given that,

Area of a parallel plate capacitor, [tex]A=1.8\ cm^2=1.8\times 10^{-4}\ m^2[/tex]

The separation between the plates of a capacitor, [tex]d=0.01\ mm = 10^{-5}\ m[/tex]

The dielectric constant of, k = 2.1

When a dielectric constant is inserted between parallel plate capacitor, the capacitance is given by :

[tex]C=\dfrac{k\epsilon_o A}{d}[/tex]

Putting all the values we get :

[tex]C=\dfrac{2.1\times 8.85\times 10^{-12}\times 1.8\times 10^{-4}}{0.01\times 10^{-3}}\\\\C=3.345\times 10^{-10}\ F\\\\C=334.5\ pF[/tex]

(b) We know that the Teflon has dielectric strength of 60 MV/m, [tex]E=60\times 10^6\ V/m[/tex]

The voltage difference between the plates at this critical voltage is given by :

[tex]V=Ed\\\\V=60\times 10^6\times 0.01\times 10^{-3} \\\\V=600\ V[/tex]

or

V = 0.6 kV

We have that the Capacitance and potential difference is mathematically given as

[tex]Vmax=\frac{Q}{334.68pF}[/tex]C=334.68pF



Capacitance &potential difference

Question Parameters:

having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm

having a plate area of 1.80 cm2 and a plate separation of 0.010 0 mm.

a)

Generally the equation for the Capacitance  is mathematically given as

[tex]C=\frac{ke_0A}{d}\\\\Therefore\\\\C=\frac{2.1*1.80e-4*8.85e12}{0.01e-3}\\\\[/tex]

C=334.68pF

b)

Generally the equation for the Capacitance  is mathematically given as

[tex]Vmax=\frac{Q}{C}[/tex]

Where

Q is the charge on the plates, and hence not given

Therefore, maximum potential difference is

[tex]Vmax=\frac{Q}{334.68pF}[/tex]

For more information on potential difference visit

https://brainly.com/question/14883923

The Bohr model pictures a hydrogen atom in its ground state as a proton and an electron separated by the distance a0 = 0.529 × 10−10 m. The electric potential created by the electron at the position of the proton is

Answers

Answer:

E = -8.23 ​​10⁻¹⁷ N / C

Explanation:

In the Bohr model, the electric potential for the ground state corresponding to the Bohr orbit is

         E = k q₁ q₂ / r²

in this case

q₁ is the charge of the proton and q₂ the charge of the electron

         E = - k e² / a₀²

let's calculate

         E = - 9 10⁹ (1.6 10⁻¹⁹)² / (0.529 10⁻¹⁰)²

         E = -8.23 ​​10⁻¹⁷ N / C

front wheel drive car starts from rest and accelerates to the right. Knowing that the tires do not slip on the road, what is the direction of the friction force the road applies to the rear tire

Answers

Answer:

The frictional force the road applies to the rear tire is static friction and it acts opposite to the direction in which the car is traveling.

Explanation:

This question suggests that the car is accelerating forward. Thus, the easiest way for us to know what friction is doing is for us to know what happens when we turn friction off.

Now, if there is no friction and the car is stopped, if we push down on the accelerator, it will make the front wheels to spin in a clockwise manner. This spin occurs on the frictionless surface with the rear wheels doing nothing while the car doesn't move.

Now, if we apply friction to just the front wheels, the car will accelerate forward while the back wheels would be dragging along the road and not be spinning. Thus, friction opposes the motion and as such, it must act im a direction opposite to where the car is going. This must be static friction.

The frictional force the road applies to the rear tire is static friction and it acts opposite to the direction in which the car is traveling.

Convert 76.2 kilometers to meters?

Answers

Answer

76200meters

Explanation:

we know that 1km=1000meters

to convert km into meters we we divide km by meters

=76.2/1000

=76200meters

Water pressurized to 3.5 x 105 Pa is flowing at 5.0 m/s in a horizontal pipe which contracts to 1/2 its former radius. a. What are the pressure and velocity of the water after the contraction

Answers

Answer:

Explanation:

Using the Continuity equation

v X A = v' xA'

so if A is 1/2of A' then A velocity must be 2 times the A'

after-contraction v = 2 x 5.0m/s = 10m/s

Using the Bernoulli equation

p₁ + ½ρv₁² + ρgh₁ = p₂ + ½ρv₂² + ρgh₂

, the "h" terms cancel

3.5 x 10^ 5Pa + ½ x 1000kg/m³x (5.0m/s)² = p₂ + ½ x 1000kg/m³ x (10m/s)²

p₂ = 342500pa

A 137 kg horizontal platform is a uniform disk of radius 1.53 m and can rotate about the vertical axis through its center. A 68.7 kg person stands on the platform at a distance of 1.19 m from the center, and a 25.9 kg dog sits on the platform near the person 1.45 m from the center. Find the moment of inertia of this system, consisting of the platform and its population, with respect to the axis.

Answers

Answer:

The moment of inertia is  [tex]I= 312.09 \ kg \cdot m^2[/tex]

Explanation:

From the question we are told that

    The  mass of the platform is   m =  137 kg

     The radius is  r  =  1.53 m

    The mass of the person is  [tex]m_p = 68.7 \ kg[/tex]

    The distance of the person from the center is  [tex]d_c =1.19 \ m[/tex]

    The mass of the dog is  [tex]m_d = 25.9 \ kg[/tex]

     The distance of the dog from the person [tex]d_d = 1.45 \ m[/tex]

Generally the moment of inertia of the system is mathematically represented as

      [tex]I = I_1 + I_2 + I_3[/tex]

Where [tex]I_1[/tex] is the moment of inertia of the platform which mathematically represented as

          [tex]I_1 = \frac{m * r^2}{2}[/tex]

substituting values

           [tex]I_1 = \frac{ 137 * (1.53)^2}{2}[/tex]

           [tex]I_1 = 160.35 \ kg\cdot m^2[/tex]

Also  [tex]I_2[/tex]  is the moment of inertia of the person about the axis which is mathematically represented as

          [tex]I_2 = m_p * d_c^2[/tex]

substituting values

          [tex]I_2 = 68.7 * 1.19^2[/tex]

          [tex]I_2 = 97.29 \ kg \cdot m^2[/tex]

Also  [tex]I_3[/tex]  is the moment of inertia of the dog about the axis which is mathematically represented as

          [tex]I_3 = m_d * d_d^2[/tex]

substituting values

          [tex]I_3 = 25.9 * 1.45^2[/tex]

          [tex]I_3 = 54.45 \ kg \cdot m^2[/tex]

Thus  

        [tex]I= 160.35 + 97.29 + 54.45[/tex]

        [tex]I= 312.09 \ kg \cdot m^2[/tex]

Two 1.0 nF capacitors are connected in series to a 1.5 V battery. Calculate the total energy stored by the capacitors.

Answers

Answer:

1.125×10⁻⁹ J

Explanation:

Applying,

E = 1/2CV²................... Equation 1

Where E = Energy stored in the capacitor, C = capacitance of the capacitor, V = Voltage of the battery.

Given; C = 1.0 nF,  = 1.0×10⁻⁹ F, V = 1.5 V

Substitute into equation 1

E = 1/2(1.0×10⁻⁹×1.5²)

E = 1.125×10⁻⁹ J

Hence the energy stored by the capacitor is 1.125×10⁻⁹ J


I MIND TRICK PLZ HELP LOL
Troy and Abed are running in a race. Troy finishes the race in 12 minutes. Abed finishes the race in 7 minutes and 30 seconds. If Troy is running at an average speed of 3 miles per hour and speed varies inversely with time, what is Abed’s average speed for the race?

Answers

Answer:

Explanation:

Let the race be of a fixed distance x

[tex]Average Speed = \frac{Total Distance}{Total Time}[/tex]

Troy's Average speed = 3 miles/hr = x / 0.2 hr

x = 0.6 miles

Abed's Average speed = 0.6 / 0.125 = 4.8 miles/hr

Intelligent beings in a distant galaxy send a signal to earth in the form of an electromagnetic wave. The frequency of the signal observed on earth is 2.2% greater than the frequency emitted by the source in the distant galaxy. What is the speed vrel of the galaxy relative to the earth

Answers

Answer:

Vrel= 0.75c

Explanation:

See attached file

The ancient Greek Eratosthenes found that the Sun casts different lengths of shadow at different points on Earth. There were no shadows at midday in Aswan as the Sun was directly overhead. 800 kilometers north, in Alexandria, shadow lengths were found to show the Sun at 7.2 degrees from overhead at midday. Use these measurements to calculate the radius of Earth.

Answers

Answer:

The  radius of the earth is [tex]r = 6365.4 \ km[/tex]

Explanation:

From the question we are told that

     The distance at  Alexandria is  [tex]d_a = 800 \ km = 800 *10^{3} \ m[/tex]

      The angle of the sun is  [tex]\theta = 7.2 ^o[/tex]

So we want to first obtain the circumference of the earth

   So let assume that the earth is  circular ([tex]360 ^o[/tex])

  Now from question we know that the sun made an angle of [tex]7.2 ^o[/tex] so with this we will obtain how many  [tex](7.2 ^o)[/tex]  are in [tex]360^o[/tex]

 i.e    [tex]N = \frac{360}{7.2}[/tex]

=>      [tex]N = 50[/tex]

     With this  value we can evaluate the circumference as

             [tex]c = 50 * 800[/tex]

              [tex]c = 40000 \ km[/tex]

Generally circumference is mathematically represented as

        [tex]c = 2\pi r[/tex]

         [tex]40000 = 2 * 3.142 * r[/tex]

=>        [tex]r = 6365.4 \ km[/tex]

Without actually calculating any logarithms, determine which of the following intervals the sound intensity level of a sound with intensity 3.66×10^−4W/m^2 falls within?

a. 30 and 40
b. 40 and 50
c. 50 and 60
d. 60 and 70
e. 70 and 80
f. 80 and 90
g. 90 and 100

Answers

Answer:

f. 80 and 90

Explanation:

1 x 10⁻¹² W/m² sound intensity falls within 0 sound level

1 x 10⁻¹¹ W/m² sound intensity falls within 10 sound level

1 x 10⁻¹⁰ W/m² sound intensity falls within 20 sound level

1 x 10⁻⁹ W/m² sound intensity falls within 30 sound level

1 x 10⁻⁸ W/m² sound intensity falls within 40 sound level

1 x 10⁻⁷ W/m² sound intensity falls within 50 sound level

1 x 10⁻⁶ W/m² sound intensity falls within 60 sound level

1 x 10⁻⁵ W/m² sound intensity falls within 70 sound level

1 x 10⁻⁴ W/m² sound intensity falls within 80 sound level

1 x 10⁻³ W/m² sound intensity falls within 90 sound level

Given sound intensity (3.66 x 10⁻⁴ W/m²) falls with 1 x 10⁻⁴ W/m² of intensity which is within 80 and 90 sound level.

f. 80 and 90

A 2.0 m × 4.0 m flat carpet acquires a uniformly distributed charge of −10 μC after you and your friends walk across it several times. A 5.0 μg dust particle is suspended in midair just above the center of the carpet.

Required:
What is the charge on the dust particle?

Answers

Answer:

The  charge on the dust particle is  [tex]q_d = 6.94 *10^{-13} \ C[/tex]

Explanation:

From the question we are told that

    The length is  [tex]l = 2.0 \ m[/tex]

    The width is  [tex]w = 4.0 \ m[/tex]

   The charge is  [tex]q = -10\mu C= -10*10^{-6} \ C[/tex]

    The mass suspended in mid-air is [tex]m_a = 5.0 \mu g = 5.0 *10^{-6} \ g = 5.0 *10^{-9} \ kg[/tex]

   

Generally the electric field on the carpet is mathematically represented as

           [tex]E = \frac{q}{ 2 * A * \epsilon _o}[/tex]

Where [tex]\epsilon _o[/tex] is the permittivity of free space with value [tex]\epsilon_o = 8.85*10^{-12} \ \ m^{-3} \cdot kg^{-1}\cdot s^4 \cdot A^2[/tex]

substituting values

           [tex]E = \frac{-10*10^{-6}}{ 2 * (2 * 4 ) * 8.85*10^{-12}}[/tex]

           [tex]E = -70621.5 \ N/C[/tex]

Generally the electric force keeping the dust particle on the air  equal to the force of gravity acting on the particles

        [tex]F__{E}} = F__{G}}[/tex]

=>     [tex]q_d * E = m * g[/tex]

=>      [tex]q_d = \frac{m * g}{E}[/tex]

=>      [tex]q_d = \frac{5.0 *10^{-9} * 9.8}{70621.5}[/tex]

=>     [tex]q_d = 6.94 *10^{-13} \ C[/tex]

A circular conducting loop of radius 31.0 cm is located in a region of homogeneous magnetic field of magnitude 0.700 T pointing perpendicular to the plane of the loop. the loop is connected in series with a resistor of 265 ohms. The magnetic field is now increased at a constant rate by a factor of 2.30 in 29.0 s.

Calculate the magnitude of induced emf in the loop while the magnetic field is increasing.

With the magnetic field held constant a ts its new value of 1.61 T, calculate the magnitude of its induced voltage in the loop while it is pulled horizontally out of the magnetic field region during a time interval of 3.90s.

Answers

Answer:

(a) The magnitude of induced emf in the loop while the magnetic field is increasing is 9.5 mV

(b) The magnitude of the induced voltage at a constant magnetic field is 124.7 mV

Explanation:

Given;

radius of the circular loop, r = 31.0 cm = 0.31 m

initial magnetic field, B₁ = 0.7 T

final magnetic field, B₂ = 2.3B₁ = 2.3 X 0.7 T = 1.61 T

duration of change in the field, t = 29

(a) The magnitude of induced emf in the loop while the magnetic field is increasing.

[tex]E = A*\frac{\delta B}{\delta t} \\\\[/tex]

[tex]E = A*\frac{B_2 -B_1}{\delta t}[/tex]

Where;

A is the area of the circular loop

A = πr²

A = π(0.31)² = 0.302 m²

[tex]E = A*\frac{B_2 -B_1}{\delta t} \\\\E = 0.302*\frac{1.61-0.7}{29} \\\\E = 0.0095 \ V\\\\E = 9.5 \ mV[/tex]

(b) the magnitude of the induced voltage at a constant magnetic field

E = A x B/t

E = (0.302 x 1.61) / 3.9

E = 0.1247 V

E = 124.7 mV

Therefore, the magnitude of the induced voltage at a constant magnetic field is 124.7 mV

Consider a series RLC circuit where R=25.0 Ω, C=35.5 μF, and L=0.0940 H, that is driven at a frequency of 70.0 Hz. Determine the phase angle ϕ of the circuit in degrees.

Answers

Answer:

137.69°

Explanation:

The phase angle of an RLC circuit  ϕ is expressed as shoen below;

ϕ = [tex]tan^{-1} \dfrac{X_l-X_c}{R}[/tex]

Xc is the capacitive reactance = 1/2πfC

Xl is the inductive reactance = 2πfL

R is the resistance = 25.0Ω

Given C = 35.5 μF, L = 0.0940 H, and frequency f = 70.0Hz

Xl = 2π * 70*0.0940

Xl = 41.32Ω

For the capacitive reactance;

Xc = 1/2π * 70*35.5*10⁻⁶

Xc = 1/0.0156058

Xc = 64.08Ω

Phase angle ϕ = [tex]tan^{-1} \frac{41.32-64.08}{25} \\\\[/tex]

ϕ = [tex]tan^{-1} \frac{-22.76}{25} \\\\\\\\[/tex]

[tex]\phi = tan^{-1} -0.9104\\\\\phi = -42.31^0[/tex]

Since tan is negative in the 2nd quadrant;

[tex]\phi = 180-42.31^0\\\\\phi = 137.69^0[/tex]

Hence the phase angle ϕ of the circuit in degrees is 137.69°

The phase angle ϕ of the series RLC circuit that is driven at a frequency of 70.0 Hz is ϕ = 137.69°

Phase angle:

Given that:

capacitance C = 35.5 μF,

Inductance L = 0.0940 H,

The resistance R = 25.0Ω

and frequency f = 70.0Hz

The capacitive reactance is given by:

Xc = 1/2πfC

Xc = 1/2π × 70 × 35.5× 10⁻⁶

Xc = 1/0.0156058

Xc = 64.08Ω

The inductive reactance is given by:

Xl = 2πfL

Xl = 2π × 70 × 0.0940

Xl = 41.32Ω

The phase angle of an RLC circuit ϕ  is given by:

[tex]\phi=tan^{-1}\frac{X_l-X_c}{R}\\\\\phi=tan^{-1}\frac{41.32-64.08}{25}[/tex]

Ф = -42.31°

Since tan is negative in the 2nd quadrant, thus:

ϕ = 180° - 42.31°

ϕ = 137.69°

Learn more about RLC circuit:

https://brainly.com/question/372577?referrer=searchResults

Astronomers think planets formed from interstellar dust and gases that clumped together in a process called? A. stellar evolution B. nebular aggregation C. planetary accretion D. nuclear fusion

Answers

Answer:

C. planetary accretion

Explanation:

Astronomers think planets formed from interstellar dust gases that clumped together in a process called planetary accretion.

Answer:

[tex]\boxed{\sf C. \ planetary \ accretion }[/tex]

Explanation:

Astronomers think planets formed from interstellar dust and gases that clumped together in a process called planetary accretion.

Planetary accretion is a process in which huge masses of solid rock or metal clump together to produce planets.

An electric train operates on 800 V. What is its power consumption when the current flowing through the train's motor is 2,130 A?

Answers

Answer:

1704 kW

Explanation:

To solve for the power consumed by the trains motor we have to employ the formula for power which is

Power= current * voltage

Given that

voltage V= 800 V

current I= 2130 A

Substituting in the formula for power we have

Power= 2130*800=  1704000 watt

Power = 1704 kW

This is the amount of energy consumed, transferred or converted per unit of time

Hence the power consumed  by the trains motor is 1704 kW

An electric heater draws 13 amperes of current when connected to 120 volts. If the price of electricity is $0.10/kWh, what would be the approximate cost of running the heater for 8 hours?
(A) $0.19
(B) $0.29
(C) $0.75
(D) $1.25
(E) $1.55

Answers

Answer:

C $0.75 my friend I wish it is right answer

Other Questions
The ratio of sales to invested assets, which is also a factor in the DuPont formula for determining the rate of return on investment, is called What aspects of the geography affect the France imports and exports? Explain how the Proclamation of 1163 could have been a major influence on the colonistsresentment towards England? I need help on this question please. Porfavor resolv erme esas preguntas o una :v porfis .El saln de mi clase de matemticas mide 700 m2, cunto mide 1/4 del saln? Cunto mide 3/4 del saln? . Cuntos minutos son 3/5 de media hora? . Se necesitan 4/7 de litro de pintura para pintar un metro cuadrado de pared, si queremos pintar 2/5 de metro cuadrado de pared, cunta pintura necesitaremos? . Si se necesitan 2/5 de naranja para hacer un vaso de jugo de naranja, cuntas naranjas necesitas para hacer 2 vasos y medio? A magnet pulls a piece of iron with a force of 1 N. What is the force that the iron piece exerts on the magnet? The iron piece exerts a force of 1 N divided by the ratio of the weight of the iron piece to the weight of the magnet in the same direction. The iron piece exerts a force of 1 N on the magnet in the opposite direction. The iron piece exerts a force of 1 N divided by the ratio of the weight of the iron piece to the weight of the magnet in the opposite direction. The iron piece exerts a force of 1 N on the magnet in the same direction. hey i suck at math can someone help me with this question Which represents a measure of volume?O 5 cmO 5 square cm05 cm05 cm Mr. B has been transferred to your floor to wait and see whether the chest tube allows his lungs to completely re-expand. But when he arrives, he is in severe respiratory distress. He says "I felt better before I came into the ER! Is this tube doing anything Can someone please help! which STD/STI can cause genital warts and cervical cancer A. Syphilis B. HPV C. Gonorrhea D. HIV/AIDS You find a new organism and are trying to determine what how it eats. You found it in a mud flat at the ocean and it has no teeth, but a very long alimentary canal. You see living examples moving through the mud very slowly. Based on all of this, you conclude that this animals is A person, with his ear to the ground, sees a huge stone strike the concrete pavement. A moment later two sounds are heard from the impact: one travels in the air and the other in the concrete, and they are 0.50 s apart. The speed of sound in air is 343 m/s, and in concrete is 3000 m/s.Required:How far away did the impact occur? |3(x2)|=12 pls help i need assistance Find the length of KE. A. 30 B. 28 C. 15 D. 3 What usually happens during the climax of a story? Write the following fractions as mixed number: 46/9, and 32/5 a positive number is 7 times another number if 3 is added to both the numbers then one of the new number becomes 5 by 2 times the other new number what are the numbers Steve wants to change shooting and exposure settings while on his photo shoot. Which camera part will allow him to do that? A. mode selection dial B. eyepiece C. aperture D. internal prism Circle12Circle the most reactive metal in each set.1) Magnesium / Potassium2) Aluminum / Gold3) Cobalt / Cesium / Calcium4) Iron / Titanium / Potassium5) Francium / Lithium / Beryllium