Help asaaap it's about doppler effect

Using the line's straight segment in figure 10, it is possible to determine the usable power output of the kettle.

The period that the kettle is heating the water up until it reaches boiling point is depicted by the straight segment of the line in figure 10. Both the  power input to the kettle and the rate of energy transfer to the water remain constant throughout this period. Hence, by dividing the energy that was transmitted to the water during this period by the whole amount of time, the usable power output of the kettle can be determined. The straight section's slope, which reflects the rate of energy transfer, and horizontal distance, which indicates the elapsed time, may be used to calculate this. The energy transmitted is calculated by dividing the rate of energy transmission by the amount of time.

learn more about  power here:

https://brainly.com/question/22285866

#SPJ4

i) The velocity of the particle at 17 sec is 17m/s.

ii) The total distance travelled is 190 m.

iii) The total displacement is -10m.

Distance is the length of any path connecting any two places. As measured along the shortest path between any two points, displacement is the direct distance between them.

The direction is ignored when calculating distance. The direction is accounted for in the displacement calculation.

Since it solely depends on magnitude and not direction, distance is a scalar number. Since displacement varies on both magnitude and direction, it is a vector quantity.

Distance provides specific directions that must be taken when moving from one location to another. Displacement only provides a partial description of the route because it pertains to the quickest way.

Velocity of particle = Slope of the object =Δ [tex]\frac{y}{x}[/tex]

Velocity = [tex]\frac{95-10}{20-15}[/tex] = 17m/s

To know more about Displacement, visit:

https://brainly.com/question/11934397

#SPJ1

"The surface of the sun appears sharp in visible light because the photosphere is thin compared to the other layers in the sun."

Most of the electromagnetic energy that reaches the earth begins in the photosphere, the area of the sun that is visible to us. The photosphere is referred to as the sun's surface, despite the fact that it is a gaseous entity.

The gas in the photosphere appears to have a sharp surface, but in reality, it is heavier lower in the Sun and less dense higher up. It is more transparent the less thick it is. The area of the gas that is visible to us is where it has largely become translucent. About 300 km of this layer are deep.

The photosphere is the line separating the core of the Sun from its atmosphere. It is the part of the Sun's surface that is visible to us. The photosphere is not like a planet's surface; even if you could stand in the sun, you couldn't do so on the photosphere.

To know more about Sun:

https://brainly.com/question/12498469

#SPJ4

The coordinated functions of the Nervous, Endocrine, and Reproductive systems are:

Coordinated functions refer to the integration and communication between different organs, systems, and tissues in the body to achieve a common goal or purpose. In biological terms, coordinated functions often involve multiple physiological systems working together to maintain homeostasis, respond to stimuli, or carry out complex behaviors or processes.

Examples of coordinated functions include the regulation of blood glucose levels by the pancreas and liver, the coordination of movement by the nervous and musculoskeletal systems, and the release of hormones by the endocrine system to control various physiological processes.

Learn more on coordinated functions here: https://brainly.com/question/15686131

#SPJ1

The question is:

"COORDINATED FUNCTIONS OF THE NERVOUS, ENDOCRINE, AND REPRODUCTIVE SYSTEMS"

Directions: Identify the part of the brain that is involved in each situation below. Write only the letter of your answer.

A. Amygdala

B. Brocka's Area

C. Cerebellum

D. Cerebrum

E. Hippocampus

F. Occipital Lobe

G. Hippocampus

H. Hypothalamus

I. Inferior Colliculus.

J. Thalamus

K. Pons

L Superior Colliculus

M. Pineal Gland

N. Wernicke's Area

O. Pituitary Gland

1. "My heart tells me that you are the one. I love you so much!"

2. "IAOCEVOY! I don't know what that means. It's all Greek to me!"

3. "Chartreuse, Olive,Turquoise, and Mint are all shades of green."

4. "Janna always wakes up at 4 in the morning, regardless of whether she uses an alarm clock or not."

5. "I don't remember the way going to Myla's house. Can you accompany me there?"

6. Jenny's mother is about to give birth, she complains about contraction and pain usually when the baby is kicking

7. "Anthony is a very skilled dancer. He just won the school hip hop dance competition last week."

8. "As Nica was walking on the road she readily moved to the side for she heard an incoming ambulance"

9. "Elsa loves making faces whenever she talks to her friends."

10. "Ryan usually talks about how happy his high school days were to his grandchildren."

The correct answer is option D.2 years

According to Kepler's Third Law of Planetary Motion, T² is proportional to r³, where T is the period of revolution of the planet and r is the distance between the planet and the star.

In order to solve for T,  

AU = 1

Astronomical Unit = the average distance between the Earth and the Sun = 149.6 million kilometres

Therefore, the planet is orbiting at a distance of 149.6 million kilometres from the star.

Substituting the values of r and solving for

T².T² ∝ r³T² ∝ (149.6)³T²

= (149.6)³T²

= 3.522 x 10¹²T

= √3.522 x 10^¹²T

= 1.87 x 10⁶ seconds

T = 31,100 minutes

T = 518 hours

T = 21.6 days

T = 2 years

Therefore, the orbital period of the planet with twice the mass of Earth orbiting at a distance of 1 AU from a star with the same mass as the Sun is 2 years.

To know more about Kepler's third law of planetary motion:

https://brainly.com/question/4978861

#SPJ11

The sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.

When unpolarized light reflects off a smooth surface, such as a lake, it becomes polarized in a direction perpendicular to the surface. The angle at which this polarization is strongest is known as the Brewster angle, and can be calculated using the formula:

θB = arctan(n2/n1)

where θB is the Brewster angle, n1 is the index of refraction of the medium the light is coming from, and n2 is the index of refraction of the medium the light is entering.

For water, the index of refraction is approximately 1.33, and for air it is approximately 1.00. Plugging these values into the formula, we get:

θB = arctan(1.33/1.00) = 53.1 degrees

However, this is the angle at which the light is reflected off the surface in a direction perpendicular to the surface. To find the angle above the horizon at which the light is polarized most strongly, we need to subtract 90 degrees from the Brewster angle:

37 degrees = 90 degrees - 53.1 degrees

Therefore, the sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.

For more similar questions on Brewster angle:

brainly.com/question/29428422

#SPJ11

The correct option is A, A block of ice of the same mass is set sliding across the floor with the same speed along a parallel line The ice has more kinetic energy.

Kinetic energy is a type of energy that an object possesses by virtue of its motion. It is defined as the energy an object has due to its motion and is proportional to the mass of the object and the square of its velocity. The formula for kinetic energy is KE = 1/2mv², where m is the mass of the object and v is its velocity.

Kinetic energy is a scalar quantity and has units of joules in the International System of Units (SI). It is a fundamental concept in physics and is used to describe many physical phenomena, including the motion of particles, the behavior of gases, and the motion of waves. In many cases, kinetic energy can be transformed into other forms of energy. For example, when a ball is thrown upwards, its kinetic energy is gradually converted into gravitational potential energy as it moves higher and higher.

To learn more about Kinetic energy visit here:

brainly.com/question/26472013

#SPJ4

Complete Question:

Basketball rolls across a floor without slipping, with its center of mass moving at a certain velocity. A block of ice of the same mass is set sliding across the floor with the same speed along a parallel line.(a) How do their energies compare?

A). The ice has more kinetic energy.

B). They have equal kinetic energies.

C). The basketball has more kinetic energy.

The net charge of a solid plastic cylinder of radius 2.33 cm and length 6.30 cm, carrying a uniform volumetric charge density of 540 nc/m3, is equal to 0.0583 nC (nanocoulombs)

To determine the net charge of a cylinder, the formula Q =ρV has to be used where Q is the net charge, ρ is the uniform volumetric charge density, and V is the volume of the cylinder.

ρ is given as 540 nc/m³.

V is calculated using the formula

V = πr²h

where r is the radius and h is the length.

π is approximated to be 3.14.  

h is given as 6.30cm

r is 2.33cm

so the calculation for V becomes;

V = πr²h

V = 3.14 x 2.33² x 6.3

V = 108.02 cm³ or 108.02 x 10⁻⁶ m³.

Substitute the values of Q and V into the equation and solve for Q:

Q = ρVQ = 540 nc/m³ x 108.02 x 10⁻⁶ m³

Q = 0.0583 nc (to 3 decimal places)

Therefore the net charge of this cylinder, in nc (nanocoulombs) is 0.0583nc.

Learn more about net charge at https://brainly.com/question/26036371

#SPJ11

Balanced net forces have equal and opposing forces that cancel each other out and provide a net force of zero, which does not alter the motion of an item.

An object's velocity remains constant and motion is unaltered when the net forces acting on it are balanced. This indicates that the thing is either stationary or moving continuously. When the forces exerted on an item are opposing in direction and of equal magnitude, they are said to be balanced forces. The forces in this situation cancel one another out, leaving a net force of zero. This can happen when one force is applied to an item and that object applies an equal and opposite force in the opposite direction to another object. It can also happen when two or more forces are applied in opposing directions and of equal magnitude. Understanding equilibrium and stability in physics requires a knowledge of the idea of balanced forces.

learn more about Balanced net forces here:

https://brainly.com/question/29769471

#SPJ4

Hydroelectric energy is generated by capturing the energy of flowing water. As water flows through a turbine, the blades of the turbine spin and generate electricity.

Wind energy is generated by capturing the kinetic energy of the wind. As wind passes through the turbine, the blades spin and generate electricity.

Geothermal energy is generated by harnessing the natural heat of the Earth’s core. Heat from the Earth’s core is used to generate steam, which is then used to spin a turbine and generate electricity.

Parabolic solar collection is a method of collecting the sun’s energy using large reflective mirrors. The mirrors focus the sunlight onto a central point, which is then used to spin a turbine and generate electricity.

Thus, all of these power sources rely on spinning turbines connected to a generator to produce electricity.

Read more about Electricity here:

https://brainly.com/question/158098

#SPJ11

The ratio of the low temperature to high temperature of the Carnot engine is 2.38.

The efficiency of the Carnot engine can be defined as the ratio of network done per cycle by the engine to the heat energy absorbed by the engine per cycle by the working substance from the source.

Efficiency = 1 - (Tlow/Thigh)


Heat absorbed by engine = 480J

Heat expelled by engine = 320J

Efficiency of the engine = 56% of efficiency of Carnot engine

The ratio of low temperature to high temperature in the Carnot engine.

Let's assume the efficiency of the Carnot engine is 'ηc' = 1 - T₂/T₁

Where, T₂ = Low temperature and T₁ = High temperature

To calculate the efficiency of the engine given, η = (Q1 - Q2)/Q1

η = (480 - 320)/480

η = 160/480

η = 1/3

η = 33.33%

Now, η = 56% × ηc

0.56ηc = 1/3ηc = (1/3)/0.56 = 0.58

As we already know, ηc = 1 - T₂/T₁

T₂/T₁ = 1 - ηc

T₂/T₁ = 1 - 0.58

T₂/T₁ = 0.42

T₁/T₂ = 1/0.42

T₁/T₂ = 2.38

Therefore, the ratio of low temperature to high temperature in the given Carnot engine with an efficiency of 56% will be about 2.38.

Learn more about Carnot engine here:

https://brainly.com/question/14680478

#SPJ11

Price elasticity of demand for radios is 1 and total revenue from radio sales will remain constant.

Price elasticity of demand is calculated as the percentage change in quantity demanded divided by the percentage change in price. Using this formula, we can calculate the price elasticity of demand for radios as follows:

Price elasticity of demand = (percentage change in quantity demanded) / (percentage change in price)

Given that when the price of radios decreases by 5%, quantity demanded increases by 5%.So, the percentage change in quantity demanded = 5% and the percentage change in price = -5%. (Because price has decreased by 5%.)Price elasticity of demand = (5% / -5%) = -1.The negative sign indicates that the demand is elastic. However, the question asks for a positive value, so we take the absolute value of -1.Price elasticity of demand = 1.

Therefore, the price elasticity of demand for radios is 1.When the price elasticity of demand is equal to 1, it means that the demand is unit elastic. This implies that the percentage change in quantity demanded is equal to the percentage change in price. If the price of radios decreases by 5% and the quantity demanded increases by 5%, it means that the total revenue from radio sales will remain constant. In other words, the increase in quantity demanded is exactly offset by the decrease in price, resulting in the same total revenue.

More price elasticity: https://brainly.com/question/22716533

#SPJ11

The resulting displacement will be 3.4 km. The correct option is A.

The displacement is calculated by finding the displacement from east to west, which is 2.0 km, and subtracting the displacement from north to south, which is 1.0 km.

A student walks 1.0 kilometers due east and 1.0 kilometers due south. Then she runs 2.0 kilometers due west. The magnitude of the student's resultant displacement is closest to 3.4 km.

To begin with, we may use the Pythagorean Theorem to determine the resultant displacement's magnitude. The Pythagorean Theorem is a formula that is used to determine the length of a right triangle's sides when one is missing. This theorem is used to calculate the magnitude of the resultant displacement, which is a quantity. It's a good idea to draw a diagram to help you understand the problem.

Here's a rough sketch of the scenario: We will now apply the Pythagorean theorem in this way: The resultant displacement's magnitude is 3.4 kilometers. Thus, the correct option is A.

To know more about displacement follow

https://brainly.com/question/14637077

#SPJ11

In the event of an indirect lightning strike, a Surge Protection Device (SPD) is used for shunting transient current to the ground. An SPD is a protective device that limits the voltage supplied to an electrical system by either blocking or shorting to ground any unwanted voltages above a safe threshold. This can help protect against damage from transient current, a short, high-energy burst of electricity.

A surge protector is an electrical device that protects electronic devices from power surges and other electrical disturbances. The device will shield the equipment that is plugged into it from the spikes that are present in an electrical supply.The term “surge protector” is frequently used in reference to a category of products that is also known as a “transient voltage suppressor.” This name provides insight into how these devices work. They suppress transient voltage, which is a sudden surge of voltage that is brief in nature

.How do surge protectors work?

Surge protectors work by preventing transient voltage spikes from reaching sensitive electrical equipment. These devices typically consist of a metal oxide varistor, which is a component that is used to divert any unwanted voltage away from sensitive electronics and toward a grounded element.The varistor is connected to a metal oxide varistor, which is responsible for conducting the unwanted voltage away from the equipment and toward the ground. Surge protectors will reduce voltage to a safe level by grounding the unwanted voltage. Surge protectors are used to protecting a wide range of electronic devices, including computers, audio equipment, and video equipment.

For more details go through the link: https://brainly.com/question/30869810

#SPJ11

Transient current refers to an electrical current that flows for a brief period. Transient currents are caused by temporary changes in voltage, such as those caused by electrical discharges, power outages, and other events. Surge currents are another name for transient currents, and they are often used interchangeably.

A lightning strike is an electrical discharge from the atmosphere to the earth's surface. Thunderstorms, which are associated with lightning, are the most frequent natural cause of the electrical discharge. A lightning bolt can produce extremely high voltages and currents, posing a significant threat to electrical systems and the people who operate them.

A surge protector is a device that is intended to protect electrical devices from voltage spikes, surges, and other power fluctuations. Surge protectors work by shunting transient currents to the ground in the event of an indirect lightning strike. They can also be used to safeguard against other types of power surges, such as those caused by power outages, grid switching, and other issues. Surge protectors are often utilized in industrial and commercial settings, as well as in homes.

For more information regarding this topic, you can click the below link

https://brainly.com/question/1100341

#SPJ11

Hydroelectric dams generate electricity through water impoundment, in which dam operators control the rate of water flow to turbines.

c is the correct option.

Hydroelectric dams are dams used to produce electricity. The movement of water drives turbines, which power generators that generate electricity.

The movement of water, generated by gravity, is what drives turbines. Hydroelectric dams are the most widely used renewable energy source, accounting for approximately 16% of global electricity production.

Hydroelectric dams generate electricity through water impoundment, in which dam operators control the rate of water flow to turbines.

This is the process of using turbines that are powered by the movement of water that has been dammed to generate electricity.

Turbines are powered by water that has been dammed to generate electricity, which is then sent to a power station to be used.

The electricity generated from hydroelectric dams is clean and safe, making it an important part of the renewable energy mix. They are also an essential part of the global infrastructure because they provide reliable, low-cost power.

They also assist in the management of rivers, flood control, and irrigation systems in various parts of the world.

To know more about Hydroelectric dams: https://brainly.com/question/18776929

#SPJ11

The speed of the block at the bottom of its slide is 16.4 m/s.

In the previous problem, the kinetic energy of the block was found to be 135 J.

The formula for kinetic energy is

KE = 1/2mv²,

Where:

Now we can use the same formula to find the velocity of the block at the bottom of its slide.

KE = 1/2mv²

We know that the mass of the block is 2 kg, and the kinetic energy at the end of the slide is 135 J.

KE = 135 Jm = 2 kg1/2mv² = 135 Jv² = 2(135 J) / 2 kgv² = 270 JV = sqrt(270 J) / 2 kgV = 16.4 m/s

Therefore, the speed of the block at the bottom of its slide is 16.4 m/s.

Learn more about kinetic energy: https://brainly.com/question/8101588

#SPJ11

The dragster's change in velocity due to the parachute can be calculated using the kinematic equation:

Δv = aΔt

where Δv is the change in velocity, a is the acceleration, and Δt is the time interval during which the acceleration occurs. In this case, the dragster is initially travelling east, so its velocity is positive, and the parachute applies a force in the opposite direction, resulting in a negative acceleration.

Given that the acceleration is -10 m/s² (westward) and the time interval is 4.5 seconds, we can calculate the change in velocity as:

Δv = (-10 m/s²) x (4.5 s) = -45 m/s

Therefore, the dragster's change in velocity due to the parachute is -45 m/s (westward). This means that the dragster's velocity is reduced by 45 m/s in the westward direction over the 4.5-second interval during which the parachute is deployed.

To know more about velocity , visit :

https://brainly.com/question/17127206

#SPJ1

The change in velocity due to the parachute is -45 m/s east

What is velocity ?

Velocity is a vector quantity that describes the speed and direction of motion of an object. In other words, velocity is the rate at which an object changes its position in a specific direction.

Velocity is expressed in units of distance per time, such as meters per second (m/s) or kilometers per hour (km/h)

Velocity is different from speed, which is also a measure of the rate of motion but only describes how fast an object is moving, without taking into account the direction of motion.

we will use the formula :-

change in velocity = acceleration x time

where acceleration is the rate at which the dragster slows down, and time is the duration for which it slows down.

Here, the dragster is travelling east, and the parachute applies a force in the opposite direction (west), causing it to slow down. So, the acceleration is -10 m/s^2 (negative because it's in the opposite direction to the velocity).

The time for which the dragster slows down is 4.5 seconds.

Therefore, the change in velocity due to the parachute is:

change in velocity = acceleration x time

change in velocity = (-10 m/s^2) x (4.5 s)

change in velocity = -45 m/s east

Note that the velocity is negative because the dragster is slowing down, and it's still travelling east (i.e., in the positive direction).

To know more about velocity visit :-

https://brainly.com/question/80295

#SPJ1

At the shop, Joselyn purchased 2700 grammes of salt water taffy.

To convert kilograms (kg) to grams (g), Joselyn would need to multiply the weight in kilograms by 1000. This is because there are 1000 grams in 1 kilogram. Therefore, to find out how many grams of salt water taffy Joselyn bought, she would need to multiply 2.7kg by 1000.

The correct answer is (B) Multiply by 1000.

Multiplying 2.7kg by 1000 gives:

2.7kg x 1000 = 2700g

So Joselyn bought 2700 grams of salt water taffy at the store.

To learn more about salt water refer to:

brainly.com/question/6829606

#SPJ4

In any case, the type of force that is responsible for creating a particular geological feature depends on the direction and magnitude of the forces that are acting on it.

Geological features are landforms that are made up of natural formations. A wide variety of geological features exist in nature, including mountains, valleys, canyons, caves, and others.

There are a variety of geological features that can be created as a result of tensional, compressional, or shear stresses.

Let's take a closer look at each type of stress:

Tensional: Tensional forces act to pull rocks apart. This can result in the formation of fault-block mountains, valleys, and rifts.

Compressional: Compressional forces act to push rocks together. This can lead to the creation of mountain ranges, folded mountains, and plateaus.

Shear Stresses: Shear stresses act to twist or bend rocks. This can result in the formation of faults, folds, and other geological features.

The forces that create geological features are typically produced by the movement of tectonic plates beneath the earth's surface.

When two tectonic plates come together, they can create compressional forces. When they move apart, they can create tensional forces.

When they slide past each other, they can create shear stresses. Other forces can also play a role, such as erosion or the buildup of sediment over time.

To know more about Geological features:https://brainly.com/question/19925491

#SPJ11

Plants help to reduce water runoff and soil erosion, both of which affect the health of streams and rivers by impacting water quality.

Soil erosion increases the silt load in the water, which can smother living organisms, particularly plants and invertebrate species. Runoff water can carry pollutants, particularly pesticides, and herbicides from agricultural land.

Landscape 1 (streams cutting through small farms with a variety of crop types and natural vegetation buffers between the fields and the streams) would be the best quality, followed by Landscape 2 (a large floodplain area covered in lowland forests and swamps full of emergent vegetation, with small streams cutting through the area) and Landscape 3 (an urban housing development where the streams are surrounded by emergent vegetation).

Learn more about water quality at  brainly.com/question/20848502

#SPJ11

The volume of the gas varies inversely with pressure, and the correct answer is (b) P/3.

According to Boyle's Law, at a constant temperature, the volume of a gas is inversely proportional to its pressure. Mathematically, this can be expressed as:

PV = k

where P is the pressure of the gas, V is its volume, and k is a constant.

If we assume that the mass of the gas remains constant, then k is also constant. So we can write:

[tex]P_1V_1 = k and P_2V_2 = k[/tex]

where[tex]P_1 and V_1[/tex] are the initial pressure and volume, and [tex]P_2 and V_2[/tex] are the final pressure and volume.

If we divide these two equations, we get:

[tex]P_1V_1/P_2V_2 = 1[/tex]

Since[tex]V_1[/tex] is inversely proportional to [tex]P_1[/tex], we can write:

[tex]V_1 = k/P_1[/tex]

Similarly, [tex]V_2 = k/P_2.[/tex]

Substituting these values in the above equation, we get:

[tex](k/P_1)/(k/P_2) = 1[/tex]

Simplifying this, we get:

[tex]P_2/P_1 = V_1/V_2[/tex]

Since we are given that the temperature remains constant, we can assume that k is constant, and therefore:

[tex]V_1/P_1 = V_2/P_2[/tex]

If we let [tex]P_2 = 3P_1[/tex], then we get:

[tex]V_1/P_1 = V_2/(3P_1)[/tex]

Simplifying this, we get:

[tex]V_1/V_2 = 1/3[/tex]

for such more question on volume

https://brainly.com/question/14197390

#SPJ11

Answer: Noble Gases (Blue)

Based on the given question, the resistance will: increase with the increase in voltage.

The reason behind this is that resistance and voltage have a direct relationship. As the voltage increases, the resistance also increases. This can be explained by Ohm’s Law which states that V= IR where V is voltage, I is current and R is resistance. As per the second part of the question, it is implied that the resistance varies with temperature.

The resistance of any material depends upon temperature, and a rise in temperature increases the resistance of the material. The light bulb acts as a resistor, and its resistance will increase as the temperature increases due to an increase in the temperature of the filament of the bulb.

The resistance is directly proportional to the temperature of the bulb, and it is represented by the equation

R = R₀ (1 + αt),

where R is resistance, R₀ is the resistance at a particular temperature, α is the temperature coefficient of resistance, and t is the temperature difference in Celsius.

Therefore, based on the data provided, it can be concluded that resistance increases with the increase in temperature which results in the heating of the light bulb, which is a resistor.

To know more about resistance refer here:

https://brainly.com/question/29427458#

#SPJ11

. Additionally, Star 1 has prominent hydrogen lines, indicating a lower temperature than Star 2. Therefore, the statements can be sorted into the true and false bins as indicated above.

True: Star 1 has a longer lifetime than Star 2; Star 2 is bluer than Star 1; Star 2 has a lower mass than Star 1; Star 1 has prominent hydrogen lines.

False: Star 2 has a higher luminosity than Star 1; Star 2 is cooler than Star 1.

The spectra of the two main sequence stars illustrate some differences between the two stars. Star 1 is on the left and has a longer lifetime than Star 2, which is on the right. This is evident from the intensity axes that are not on the same scale. Star 2 has a lower mass than Star 1, is bluer than Star 1, and has a lower luminosity

for such more questions on hydrogen lines

https://brainly.com/question/30461609

#SPJ11

The center of mass of the two-car system can be found by taking the weighted average of the velocities of the two cars.

The velocity of the center of mass is the average of the two cars' velocities, weighted by their masses. The velocity of the center of mass is:

Velocity of Center of Mass = (1.27 x 103 kg x 11.6 m/s + 1.70 x 103 kg x 11.6 m/s) / (1.27 x 103 kg + 1.70 x 103 kg) = 11.60 m/s.

Read more about the topic velocity:

https://brainly.com/question/80295?source=archive

#SPJ11

The electric potential energy, U, of two point charges is given by the equation, U = kq1q2/r where k is Coulomb's constant, q1 and q2 are the charges and r is the distance between the two charges. Now, let's solve the question using this equation. There are two charges, q1 and q2, and a parallel plate capacitor between them. The distance of q1 from the negative plate is s, and the distance of q2 from the negative plate is 2s. The charges have the same magnitude of charge, so let's assume q1 = q2 = q. Using the formula mentioned earlier, we get U1= kq^2/sU2= kq^2/2s. Therefore, the ratio of their potential energies is U2/U1= kq^2/2s / kq^2/sU2/U1= (kq^2/2s) × (s/kq^2)U2/U1= 1/2.

Therefore, the ratio of their potential energies is 1:2.

For more information regarding this topic, you can click the below link

https://brainly.com/question/14306881

#SPJ11

There are 7.86 x 10²³ electrons in a 30.0 cm length of 12-gauge copper wire with a diameter of 2.05 mm.

To calculate the number of electrons in a 30.0 cm length of 12-gauge copper wire (diameter 2.05 mm), you can use the following equation:

n = ρV / m

where:

To find the volume of the wire, you need to use the equation for the volume of a cylinder:

Where:

Therefore, V = π(1.025 mm)²(30.0 cm) = 9.30 cm³The mass of one copper atom is 63.55 g/mol or 1.054 x 10⁻²² g. To find m, you need to use Avogadro's number (6.02 x 10^23 atoms/mol):m = (63.55 g/mol) / (6.02 x 10^23 atoms/mol) = 1.055 x 10⁻²² g

Now, you can plug in the values:

n = (8.96 g/cm³)(9.30 cm³) / (1.055 x 10⁻²² g) = 7.86 x 10²³ electrons

Therefore, there are 7.86 x 10²³ electrons in a 30.0 cm length of 12-gauge copper wire with a diameter of 2.05 mm. This should be rounded to 2 significant figures, so the final answer is 7.9 x 10²³ electrons.

Learn more about electrons: https://brainly.com/question/26084288

#SPJ11

Alpha particle emission, beta particle emission, and electron capture are all common types of radioactive decay.The correct answer is D.

They are common types of radioactive decay's because:

Option D includes all of these types of radioactive decay (alpha particle emission, beta particle emission, and electron capture), so it is the correct answer

To learn more about radioactive decay:

https://brainly.com/question/11117468

#SPJ11