Explanation:
The size of the force varies inversely as the square of the distance between the two charges. Therefore, if the distance between the two charges is doubled, the attraction or repulsion becomes weaker, decreasing to one-fourth of the original value.
Question 1 of 25
Which equation is an example of a synthesis reaction?
A. HNO3 + KOH → KCI + H20
B. 2Li+ CaCl2 - 2LiCl + Ca
O C. S+ 02 - S02
7
O D. CH4 + 202 - 2H2O + CO2
Answer:
C. S + 02 → S02
Explanation:
A synthesis or combination reaction is that reaction involving two elements as reactants to form a single compound as product.
In the reaction given below;
S + 02 → S02
Sulphur and oxygen are elemental substances that combine to synthesize sulfur IV oxide (SO2), and hence it is an example of synthesis reaction.
You take your pulse and observe 80 heartbeats in a minute. What is the period of your heartbeat? What is the frequency of your heartbeat?
Answer:
120 beats per minute.
Explanation:
If I take your pulse and observe 80 heartbeats in a minute. Then the period of your heartbeat is 0.8 s and frequency is 1.3Hz.
What is Heartbeat ?A pulse is the term used in medicine to describe the tactile arterial palpation of the cardiac cycle (heartbeat) by skilled fingertips. Any location where an artery can be compressed close to the surface of the body, such as the carotid artery in the neck, the radial artery in the wrist, the femoral artery in the groyne, the popliteal artery behind the knee, the posterior tibial artery near the ankle joint, and on the foot, can be used to palpate the pulse (dorsalis pedis artery). Heart rate may be determined by monitoring pulse, or the number of arterial pulses per minute. Auscultation, which is the process of counting the heartbeats while listening to the heart using a stethoscope, is another way to determine the heart rate. Typically, three fingers are used to gauge the radial pulse.
Given,
heart beat = 80 beats/min = 1.3 beats/s
Frequency is nothing but how much beats is heart having in one second and that is 1.3 beats/s. Hence frequency of heart is 1.3Hz.
The Period is reciprocal of frequency,
T = 1/f = 0.8 s
To know more about frequency :
https://brainly.com/question/29739263
#SPJ2.
Một vật chuyển động tròn đều có chu kì T = 0,25 s. Tính tần số chuyển động f của vật?
Explanatio
omega=2pi/T
Answer:
0
0000
Explanation:
Alice's friends Bob and Charlie are having a race to a distant star 10 light years away. Alice is the race official who stays on Earth, and her friend Darien is stationed on the star where the race ends. Bob is in a rocket that can travel at 0.7c; whereas Charlie's rocket can reach a speed of 0.866c. Bob and Charlie start at the same time. Draw space- diagrams from each perspective.
Required:
Estimate how long it takes Bob and Charlie to finish the race from each perspective.
Solution :
The distance between the starting point and the end point, [tex]L_0[/tex] = 10 light years
But due to the relativistic motion of Bob and Charlie, the distance will be reduced following the Lorentz contraction. The contracted length will be different since they are moving with different speeds.
For Bob,
Speed of Bob's rocket with respect to Alice, [tex]L_b = 0.7 \ c[/tex]
So the distance appeared to Bob due to the length contraction,
[tex]$L_b=L_0\sqrt{1-\frac{V_b^2}{c^2}$[/tex]
[tex]$L_b=10\times \sqrt{1-0.49} \ Ly$[/tex]
[tex]$=7.1 \ Ly$[/tex]
Therefore, the time required to finish the race by Bob is
[tex]$t_b = \frac{L_b}{V_b}$[/tex]
[tex]$=\frac{7.1 \ c}{0.7 \ c}$[/tex]
= 10.143 year
For Charlie,
Speed of Charlie's rocket with respect to Alice, [tex]L_c = 0.866 \ c[/tex]
So the distance appeared to Charlie due to the length contraction,
[tex]$L_b=L_0\sqrt{1-\frac{V_c^2}{c^2}$[/tex]
[tex]$L_b=10\times \sqrt{1-0.75} \ Ly$[/tex]
[tex]$=5 \ Ly$[/tex]
The time required to finish the race by Charlie is
[tex]$t_b = \frac{L_c}{V_c}$[/tex]
[tex]$=\frac{5 \ c}{0.866 \ c}$[/tex]
= 5.77 year
To a man running east at the rate of 3m/s vain appears to fall vertically with a speed of 4m/s. Find the actual speed and direction of rain...
Answer:
The actual speed of the rain is 5 m/s and its direction is -53.13°
Explanation:
The actual speed of the rain V = speed of man, v + speed of rain relative to man, v'.
V = v + v'
We add these vectorially.
Since the man's speed is 3 m/s east, in the positive x - direction, we have v = 3i and the rain's speed is falling vertically at 4 m/s, in the negative y- direction, we have v' = -4j
So, V = v + v'
V = 3i + (-4j)
V = 3i - 4j
So, the magnitude of V which is its speed is V = √(3² + (-4)²) = √(9 + 16) = √25 = 5 m/s
The direction of V, Ф = tan⁻¹(vertical component/horizontal component) = tan⁻¹(-4/3) = tan⁻¹(-4/3) = tan⁻¹(-1.333) = -53.13°
So, the actual speed of the rain is 5 m/s and its direction is -53.13°
Ocean waves of wavelength 22 m are moving directly toward a concrete barrier wall at 4.6 m/s . The waves reflect from the wall, and the incoming and reflected waves overlap to make a lovely standing wave with an antinode at the wall. (Such waves are a common occurrence in certain places.) A kayaker is bobbing up and down with the water at the first antinode out from the wall.
Required:
a. How far from the wall is she?
b. What is the period of her up-and-down motion?
Answer:
a) [tex]d=11m[/tex]
b) [tex]T=4.68s[/tex]
Explanation:
From the question we are told that:
Wavelength [tex]\lambda=22m[/tex]
Velocity [tex]v=4.6m/s[/tex]
a)
Generally the equation for distance between her and the wall d is mathematically given by
Since
The First Anti node distance is [tex]\frac{\lambda}{2}[/tex]
Therefore
[tex]d= \frac{\22}{2}[/tex]
[tex]d=11m[/tex]
b)
Generally the equation for her up-and-down motion is mathematically given by
[tex]T=\frac{22}{4.7}[/tex]
[tex]T=4.68s[/tex]
Suppose there are 3 molecules in a container. If each molecule has a 1-in-2 chance of being in the left half of the container, what is the probability that there are exactly 2 molecules in the left half of the container?
Answer:
Total probability = 3/8
Explanation:
Below is the calculation:
Number of molecules in the container = 3
The probability of one molecule in the left half, P = 3 / 2 = 1.5 or 1/2
The probability of second molecule in the left half, P1 = (3/4)
Total probability = P x P1
Total probability = (1/2) x (3/4)
Total probability = 3/8
If a rock displaces 7 ml of water, what is the volume of the rock?
Answer:
if i am not mistaken the volume is 7, because it only took that much space
HELP ME PLEASE!!!
Which 2 statements are true about this chemical reaction that forms acid rain?
Answer:
B.
Explanation:
HNO2 is less stable thus dissociates easily to HNO3 + NO + H2O while HNO3 is a strong acid. Thus when they react with H2O they form acid rain
Answer:
B
Explanation:
dont have one just trust me
An iron nail floats in mercury and sinks in water. explain why?
Answer:
because density of iron is more than that of water but less then that of Mercury
hope it's helpful
Answer the following questions
1. Heat in liquid travels from
a) bottom to top
b) top to bottom
c) left to right
d) right to left
2. The direction of flow of heat is
a) always from a cooler body to a hotter body
b) always from a hotter body to cooler body
c) always from a body at a lower temperature to a body at a higher temperature
d) all the above
3. A cold steel spoon is dipped in a cup of hot milk. The steel spoon transfer the heat to its other end by the process of
a) convection
b) conduction
c) radiation
d) none of the above
A swift blow with the hand can break a pine board. As the hand hits the board, the kinetic energy of the hand is transformed into elastic potential energy of the bending board; if the board bends far enough, it breaks. Applying a force to the center of a particular pine board deflects the center of the board by a distance that increases in proportion to the force. Ultimately the board breaks at an applied force of 870 N and a deflection of 1.4 cm.
a. To break the board with a blow from the hand, how fast must the hand be moving? Use 0.50 kg for the mass of the hand.
b. If the hand is moving this fast and comes to rest in a distance of 1.2 cm, what is the average force on the hand?
Answer:
A. The hand must move with a velocity of 6.98 m/s to break the board.
B. Average force on the hand = 1025 N
Explanation:
A.To determine the speed the hand must move with to break the board, the force workdone in breaking the board is found first.
Workdone = force × distance
Minimum force required = 870 N;
Distance moved by board/Deflection in order to break = 1.4 cm = 0.014 M
Workd done = 870 N × 0.014 m = 12.18 Nm or 12.18 J
This work done = Kinetic energy of the hand
Kinetic energy = mv²/2 ; where m is mass and v is velocity
Mass of hand = 0.50 Kg, velocity = ?, K.E. = 12.18 J
v² = 2 KE/m
v = √2KE/m
v = √(2 × 12.18/0.50)
v = 6.98 m/s
Therefore, the hand must move with a velocity of 6.98 m/s to break the board.
B. Average force on the hand
This can be determined using the equation of motion, v² = u² + 2as to find acceleration, since force = mass × acceleration
From the equation of motion, a = v² - u²/2s
At rest, v = 0, u = 6.98, s = 1.2 cm = 0.012 m
a = 0² - 6.98²/ 2 × 0.012
a = -2030 m/s²
Force = 2030 m/s² × 0. 50 kg = 1015 N
Therefore, Average force on the hand = 1025 N
help plzzzzzzzzzzzz ?
Explanation:
1. First, let's find the total resistance of the circuit. We begin by combining [tex]R_{4}[/tex], [tex]R_{5}[/tex] and [tex]R_{6}[/tex]:
[tex]R_{456}=R_{4} + \dfrac{R_{5}R_{6}}{R_{5} + R_{6}}[/tex]
[tex]= 6\:Ω + \dfrac{(3\:Ω)(5\:Ω)}{3\:Ω+5\:Ω} = 7.9\:Ω[/tex]
Now time to combine [tex]R_{2}[/tex] and [tex]R_{3}[/tex] and they are connected in series so
[tex]R_{23} =R_{2} + R_{3} = 17\:Ω[/tex]
Note that [tex]R_{23}[/tex] and [tex]R_{456}[/tex] are connected in parallel so
[tex]R_{23456} = \dfrac{R_{23}R_{456}}{R_{23}+R_{456}}=5.4\:Ω[/tex]
Finally, [tex]R_{23456}[/tex] is connected in series with [tex]R_{1}[/tex] so the total resistance [tex]R_{T}[/tex] is
[tex]R_{T} = R_{1} + R_{23456} = 10\:Ω + 5.4\:Ω = 15.4\:Ω[/tex]
2. The total current in the circuit is
[tex]I_{T} = \dfrac{V}{R_{T}} = \dfrac{20\:V}{15.4\:Ω} = 1.3\:A[/tex]
3. The voltage drop across [tex]R_{1},\:V_{1}[/tex] is
[tex]V_{1} = I_{T}R_{1} = (1.3\:A)(10\:Ω) = 13\:V[/tex]
4. We can see that [tex]I_{T} = I_{1} + I_{2}[/tex]. To solve for [tex]I_{1}[/tex], we need [tex]V_{23}[/tex], which is just [tex]V_{T} - V_{1} = 20\:V - 13\:V = 7\:V[/tex] , which gives us
[tex]I_{1} = \dfrac{V_{23}}{R_{23}} = \dfrac{7\:V}{17\:Ω} = 0.4\:A[/tex]
5. From #2 & #4, [tex]I_{2} = 1.3\:A - 0.4\:A = 0.9\:A[/tex] and we also know that the voltage drop across [tex]R_{456}[/tex] is 7 V, the same as that of [tex]R_{23}[/tex]. The voltage drop across [tex]R_{4}[/tex] is
[tex]V_{4} = I_{2}R_{4} =(0.9\:A)(6\:Ω) = 5.4\:V[/tex]
This means that the voltage drop across [tex]R_{6}[/tex] is 7 V - 5.4 V = 1.6 V. Knowing this, the current through [tex]R_{6}[/tex] is
[tex]I_{6} = \dfrac{1.6\:V}{5\:Ω} = 0.3\:A[/tex]
A conductor is placed in an external electrostatic field. The external field is uniform before the conductor is placed within it. The conductor is completely isolated from any source of current or charge.
1. Which of the following describes the electricfield inside this conductor?
a. It is in thesame direction as the original external field.
b. It is in theopposite direction from that of the original externalfield.
c. It has adirection determined entirely by the charge on itssurface.
d. It is alwayszero.
2. The charge density inside theconductor is:
a. 0
b. non-zero;but uniform
c. non-zero;non-uniform
d. infinite
Answer:pp
Explanation:
ii
40 ohms
1.2 A
40 ohms
12 V
Calculate the total energy developed in 5
minutes by the system above.
Answer:
17280 J and 1080 J
Explanation:
Given :
R= 40 ohm
I=1.2A
t= 5 min=60×5=300 sec
Now,
Total energy can be calculated as:
[tex]E=I^{2} Rt\\E=(1.2)^{2} *40*300\\E=17280 J[/tex]
Now,
V=12V
R=40 Ohm
[tex]E=\frac{V^{2} }{R} *t\\E=\frac{(12)^{2} }{40} *300\\E=1080 J[/tex]
Total energy is 17280 J and 1080 J
A car of mass M traveling with velocity v strikes a car of mass M that is at rest. The two cars’ bodies mesh in the collision. The loss of the kinetic energy the moving car undergo in the collision is
a) a quarter of the initial kinetic energy.
b) half of the initial kinetic energy.
c) all the initial kinetic energy.
d) zero.
Answer:
the correct answer is B
Explanation:
Let's propose the solution of the problem, for this we form a system formed by the two cars, so that the forces during the collision are internal, the momentum is conserved
instantly starts. Before the crash
p₀ = M v +0
final instant. After the crash
m_f = (M + M) v_f
the moment is preserved
p₀ = p_f
M v = 2 M v_f
v_f = v / 2
let's look for kinetic energy
before the crash
K₀ = ½ M v²
after the crash
K_f = ½ 2M (v_f)²
K_f = ½ 2M (v/2)²
K_f = (½ M v²) ½
K_f = K₀ / 2
therefore the correct answer is B
Hey, can a physics major help me?
I have been wondering about the exact difference between theories laws facts and hypothosis.
I know the general layout but I am still a bit confused.
100 points for answering and brainly if it is a good one.
Answer:
A hypothesis is a limited explanation of a phenomenon; a scientific theory is an in-depth explanation of the observed phenomenon. A law is a statement about an observed phenomenon or a unifying concept
Answer:
Explanation:
will try 2 explain fact, hypothesis, theory n law
fact is the starting pt: e.g. apple falls from tree
hypothesis tries 2 explain a fact: e.g. there is a force pulling down apple
theory is a complete explanation w/ equations n stuff: e.g. Newton came up w/ theory of gravitational attraction force
law is a theory dat has been proven right through tests n experiments: Newton's gravity theory had been proven right in many many tests.
What is the magnitude of a vector that has the following components: x = 32 m y = -59 m
Answer:
Explanation:
Since the x and y components are given
The vectors Magnitude = √32²+(-59)²
=67.12m
The lumberjack pulls on the sled with 40 N at an angle of 30 degrees, pulling so the sled moves at a constant velocity. 1) What is the x component of the applied force? 2) What is the y component of the applied force? 3) If the loaded sled has a mass of 65 kg, what is the magnitude of the force of gravity? 4) What is the magnitude of the normal force acting on the sled? 5) What is the coefficient of friction between the snow and the sled?
1) (40 N) cos(30°) ≈ 34.6 N
2) (40 N) sin(30°) = 20 N
3) (65 kg) g = (65 kg) (9.80 m/s²) = 585 N
4) The net force on the sled acting in the vertical direction is made up of
• the sled's weight, 585 N, pointing downward
• the vertical component of the applied force, 20 N, pointing upward
• the normal force, with magnitude n, also pointing upward
The sled does not move up or down, so by Newton's second law,
∑ F = n + 20 N - 585 N = 0 ==> n = 565 N
5) The net force in the horizontal direction consists of
• the horizontal component of the applied force, 34.6 N, acting in the direction the sled's movement (call this the positive direction)
• kinetic friction, with magnitude f, pointing in the opposite and negative direction
By Newton's second law,
∑ F = 34.6 N - f = 0 ==> f ≈ 34.6 N
Now if µ is the coefficient of kinetic friction, then
f = µn ==> µ = f/n = (34.6 N) / (565 N) ≈ 0.0613
The component of the force is the effective part of that force in that direction.
What is the component of a force?The component of the force is the effective part of that force in that direction.
1) The horizontal component of a force = 40 N cos 30 degrees = 34.6 N
2) The vertical component of the force = 40 N sin 30 degrees = 20 N
3) The magnitude of the gravitational force = mg cos 30 degrees = 65 Kg * 9.8 m/s^2 * cos 30 degrees = 551.7 N
4) The normal force = 551.7 N
5) The coefficient of friction = F/R = 40 N /551.7 N = 0.07
Learn more about component of a force:https://brainly.com/question/15529350
#SPJ6
what is effort arm
don't say the answer of gogle
Answer:
effort arm mean the use of any work by using your hand force motion or by hand power
what is the resistance of a bulb of 40w connected in a line of 70v
Answer:
122.5 ohm
Explanation:
Given :
P=40 w
V= 70 V
R=?
Resistance can be calculated as :
[tex]P=\frac{V^{2} }{R} \\40=\frac{(70)^{2} }{R}\\40=\frac{4900}{R} \\R=\frac{4900}{40} \\R=122.5 ohm[/tex]
Therefore, resistance of the bulb will be 122.5 ohm
a brick of mass 0.8 kg is accidentally dropped from a high scaffolding. it reaches the ground with a kinetic energy of 240 J. How high is scaffolding ?(Take acceleration due to gravity g be 10 m s-¹)
Answer:
30 m
General Formulas and Concepts:
Energy
Gravitational Potential Energy: [tex]\displaystyle U_g = mgh[/tex]
m is mass (in kg)g is gravityh is height (in m)Kinetic Energy: [tex]\displaystyle KE = \frac{1}{2}mv^2[/tex]
m is mass (in kg)v is velocity (in m/s²)Law of Conservation of Energy
Explanation:
Step 1: Define
Identify variables
[Given] m = 0.8 kg
[Given] g = 10 m/s²
[Given] U = 240 J
[Solve] h
Step 2: Solve for h
[LCE] Substitute in variables [Gravitational Potential Energy]: (0.8 kg)(10 m/s²)h = 240 JMultiply: (8 kg · m/s²)h = 240 JIsolate h [Cancel out units]: h = 30 mIn addition to acceleration, what else will be a maximum at the amplitude for SHM?
A. Potential energy
B. Kinetic energy
C. Nuclear energy
D. Chemical energy
It is Potential energy's
A heat engine with 0.100 mol of a monatomic ideal gas initially fills a 3000 cm3 cylinder at 800 K. The gas goes through the following closed cycle Isothermal expansion to 5000 cm3 ?
Part A How much work does this engine do per cycle? Express your answer with the appropriate units. sochoric cooling to 200 K -Isothermal compression to 3000 cm3. - Isochoric heating to 800 K Value Units
Part B What is its thermal efficiency? Express your answer with the appropriate units.
Answer:
below
Explanation:
Part A) This engine works per cycle is 254.9 J.
Part B) The thermal efficiency is 23.42%
What is the thermal efficiency?The thermal efficiency of any heat engine is represented in percentage of heat energy converted into work.
For isothermal expansion, work done is
W₁ =nRT₁ x ln(V₂/V₁)
W₁ = 0.1 x 8.314 x 800 x ln(5000/3000)
W₁ = 339.8 J =Q₁
For isochoric cooling ,
W₂ =0
Q₂ =nCvdT = 0.1 x 3R/2 x (T₂-T₁)
Q₂ = -748.3 J
For isothermal compression,
W₃ =nRT₂ ln (V₄/V₃)
W₃ = 0.1 x 8.314 x 200 x ln(3000/5000)
W₃ = -84.9J
For isochoric heating
W₄ =0
Q₄ =nCvdT = 0.1 x 3R/2 x (800-200)
Q₄ = -748.3 J
Total work done in all the process W = W₁ +W₂ +W₃ +W₄
W =254.9 J
Thus, the work done is 254.9 J
Thermal efficiency = Work done/Heat taken
η = W/ Q₁ +Q₄
η = [254.9 / 339.8 +748.3 ] x 100 %
η = 0.2342 x 100 %
η = 23.42%
Thus, the thermal efficiency is 23.42%
Learn more about thermal efficiency.
https://brainly.com/question/13039990
#SPJ2
'
Determine the values of m and n when the following average magnetic field strength of the Earth is written in scientific notation: 0.0000451 T. Enter m and n, separated by commas.
Answer:
B = 4.51×10⁻⁵ T
Explanation:
Given that,
The average magnetic field strength of the Earth is 0.0000451 T.
We need to write the value in the form of scientific notation. Any number in scientific notation is written as follows :
N=a×bⁿ
Where
n is any integer and a is a real no
So,
0.0000451 = 4.51×10⁻⁵ T
So, the required answer is equal to 4.51×10⁻⁵ T.
What must a plant need to produce 4 molecules of sugar?
What must a plant need to produce 4 molecules of sugar?
Answer:
To produce a single sugar molecule a plant must use a molecule of water (H2O) and carbon dioxide (CO2) and sunlight. To get 4 molecules, you simple use 4 molecules of water and 4 molecules of carbon dioxide
Một ô tô khối lượng một tấn chuyển động trên một đường nằm ngang. Hệ số ma sát giữa bánh ô tô và mặt đường là 0,07. Gia tốc trọng trường g=9,8m/s2
a) vẽ và xác định tên các lực tác động lên vật. Viết phương trình chuyển động của vật.
b) nếu ô tô chuyển động đều, xuống dốc có độ dốc 5%. Tính lực kéo của ô tô.
c) nếu ô tô chuyển động đều. Lên dốc có độ dốc 5%. Tính lực kéo của động cơ ô tô
Which of the following phenomenon odd called photoelectric effect?
A. High energy electrons impinge on a metallic Annie which emits electrons
B. A high energy photon emits photons as it slows down
C. A metal absorbs a quanta of light and then emits electrons
D. Two electrons are created from a quanta of light.
two electrons are created from a quanta of kight
What does a model of a light wave tell us about
brightness and color?
Answer:
A wave model of light is useful for explaining brightness,color, and the frequency-dependent bending of light at a surface between media. However, because light can travel through space, it cannot be a matter wave, like sound or water waves.
When you release some of the paint from a spray paint can and the can remains at the same temperature, which gas law does this represent?
Answer:
Boyle's law.
Explanation:
Robert Boyle was an Irish chemist and is famously referred to as the first modern chemist. He was born on the 25th of January, 1627 in Lismore, Ireland and died on the 31st, December 1691, London, United Kingdom.
Boyles states that when the temperature of an ideal gas is kept constant, the pressure of the gas is inversely proportional to the volume occupied by the gas.
Mathematically, Boyles law is given by;
[tex] PV = K[/tex]
[tex] P_{1}V_{1} = P_{2}V_{2} [/tex]
Where;
P1 is the original pressure.
P2 is the final pressure.
V1 is the original volume.
V2 is the final volume.
Hence, when you release some of the paint from a spray paint can by applying an amount of pressure and the can remains at the same temperature, the gas law which this represent is Boyle's law.
