If there is a discrepancy between Chick-fil-A food safety requirements and local Health Department
regulations, what should Team Member do?

Answers

Answer 1
It is important to follow both Chick-fil-A food safety requirements and local Health Department regulations. If there is a discrepancy between the two, always follow the more stringent requirement. Any other appearance or grooming issue not covered in these materials may be addressed at the discretion of the Operator.
Answer 2

The following should be done by the team member:

It is important to follow both Chick-fil-A food safety requirements and local Health Department regulations. In the case when there is a discrepancy between the two, always follow the more stringent requirement. Any other appearance or grooming issue not covered in these materials may be addressed at the discretion of the Operator.

Learn more: brainly.com/question/17429689


Related Questions

g Steel plates (AISI 1010) of 4 cm thickness initially at a uniform temperature of 500 deg C are cooled by air at 50 deg C with a convection coefficient of 30 W-m2-K-1. Estimate the time it will take for their midplane temperature to reach 100 deg C.

Answers

Solution :

Characteristic length  = thickness / 2

                                    [tex]$=\frac{0.04}{2}$[/tex]

                                    = 0.02 m

Thermal conductivity for steel is 42.5 W/m.K

[tex]$\text{Biot number} = \frac{\text{convective heat transfer coefficient} \times \text{characteristic length}}{\text{thermal conductivity}}$[/tex]

                  [tex]$=\frac{30 \times 0.02}{42.5}$[/tex]

                  = 0.014

Since the Biot number is less than 0.01, the lumped system analysis is applicable.

[tex]$\frac{T-T_{\infty}}{T_0-T_{\infty}} = e^{-b\times t}$[/tex]

Where,

T = temperature after t time

[tex]$T_{\infty}$[/tex] = surrounding temperature

[tex]$T_0$[/tex] = initial temperature

[tex]$b=\frac{\text{heat transfer coefficient}}{\text{density} \times {\text{specific heat } \times \text{characteristic length }}}$[/tex]

t = time

We calculate B:

[tex]$b=\frac{30}{7833 \times 460 \times 0.02}$[/tex]

  = 0.000416

Thus, [tex]$\frac{100-50}{500-50}=e^{-0.00416 \times t}$[/tex]

t = 5281.78 second

  = 88.02 minutes

Thus the time taken for reaching 100 degree Celsius is 88.02 minutes.

a) Complete the following methods description using the correct tense for the verb in brackets. (This student is using passive voice rather than any human agents at the request of the instructor.) Student Lab Report Identical tensile test procedures were performed on all test specimens. Each of the metal specimens ____1____ [have] an indentation near the center to ensure that the fracture point would occur in this region. Tension tests ____2____ [conduct] as follows. Two pieces of reflective tape ____3____ [place] approximately 1 inch apart in the center of the specimen where the indentation 4 [locate]. The width and the thickness of the specimen at this location _____5_____ [measure] using a Vernier caliper. Then the specimen _____6____ [secure] in the MTS Load Frame. A laser extensometer _____7_____ [place] into position to measure the deformation of the specimen. The laser extensometer ______8_ __ [use] to measure the original distance between the pieces of reflective tape. The MTS ________9____ [set] to elongate the specimen one tenth of an inch every minute.

Answers

Answer:

Each of the metal specimens HAS an indentation near the center to ensure that the fracture point would occur in this region. Tension tests WERE CONDUCTED as follows. Two pieces of reflective tape WERE PLACED approximately 1 inch apart in the center of the specimen where the indentation 4 WAS LOCATED. The width and the thickness of the specimen at this location WAS MEASURED using a Vernier caliper. Then the specimen WAS SECURED in the MTS Load Frame. A laser extensometer WAS PLACED into position to measure the deformation of the specimen. The laser extensometer WAS USED to measure the original distance between the pieces of reflective tape. The MTS WAS SET to elongate the specimen one tenth of an inch every minute.

A hollow pipe is submerged in a stream of water so that the length of the pipe is parallel to the velocity of the water. If the water speed doubles and the cross-sectional area of the pipe triples, what happens to the volume flow rate of the water passing through it?

Answers

Answer:

increases by a factor of 6.

Explanation:

Let us assume that the initial cross sectional area of the pipe is A m² while the initial velocity of the water is V m/s², hence the flow rate of the water is:

Initial flow rate = area * velocity = A * V = AV m³/s

The water speed doubles (2V m/s) and the cross-sectional area of the pipe triples (3A m²), hence the volume flow rate becomes:

Final flow rate = 2V * 3A = 6AV m³/s = 6 * initial flow rate

Hence, the volume flow rate of the water passing through it increases by a factor of 6.

An ideal neon sign transformer provides 9130 V at 51.0 mA with an input voltage of 240 V. Calculate the transformer's input power and current.

Answers

Answer:

Input power = 465.63 W

current = 1.94 A

Explanation:

we have the following data to answer this question

V = 9130

i = 0.051

the input power = VI

I = 51.0 mA = 0.051

= 9130 * 0.051

= 465.63 watts

the current = 465.63/240

= 1.94A

therefore the input power is 465.63 wwatts

while the current is 1.94A

the input power is the same thing as the output power.

Explain by Research how a basic generator works ? using diagram

Answers

Correcto no se muy bien de que se trata el tema porque está en inglés.
Sorry

Calculate density, specific weight and weight of one litter of petrol having specific gravity 0.7

Answers

Explanation:

mass=19kg

density=800kg/m³

volume=?

as we know that

density=mass/volume

density×volume=mass

volume=mass/density

putting the values

volume=19kg/800kg/m³

so volume=0.02375≈0.02m³

it is a small sharp and printed item for fine worker in trimming scallops clipping threads and cutting large eyelets​

Answers

Answer:

embroidery scissor

Explanation:

is small, sharp and pointed good for fine work use trimming scallops,clipping threads,and cutting large eyelets.

hope this helps

On a two-way roadway with a center lane, drivers from either direction can _________ from the center lane.

Answers

1. left turn
2. right turn
3. u-turn
4. frequent stops

what are qualifications that are required to be an architect​

Answers

Answer:

Bachelor's degree

In order to become a licensed architect in the US and the District of Columbia, applicants are required to complete a professional degree in architecture, gain on-the-job experience through a paid internship.

Cite another example of information technology companies pushing the boundaries of privacy issues; apologizing, and then pushing again once scandal dies down. As long as the controversy fades, is there anything unethical about such a strategy?

Answers

Answer:

Explanation:

Tech Social Media giant FB is one of those companies. Not long ago the ceo was brought to court to accusations that his company was selling user data. Turns out this is true and they are selling their users private data to companies all over the word. Once the news turned to something else, people focused on something new but the company still continues to sell it's users data the same as before. This is completely unethical as the information belongs to the user and they are not getting anything while the corporation is profiting.

Suppose a causal CT LTI system has bilateral Laplace transform H(s) 2s - 2 $2 + (10/3)s + 1 (8)
(a) Write the linear constant coefficient differential equation (LCCDE) relating a general input x(t) to its corresponding output y(t) of the system corresponding to this transfer function in equation (8).
(b) Suppose the input x(t) = e-tu(t). Find the output y(t). In part (c), the output signal can be expressed as y(t) = - e-(1/3)t u(t) + e-tu(t) e-3tu(t), - 019 Where a, b, and care positive integers. What are they? a = b = C=

Answers

Solution :

Given :

[tex]$H(S) =\frac{2S-2}{S^2+\left(\frac{10}{3}\right) S+1}$[/tex]

Transfer function, [tex]$H(S) =\frac{Y(S)}{K(S)}= \frac{2S-2}{S^2+\left(\frac{10}{3}\right) S+1}$[/tex]

[tex]$Y(S) \left(S^2+\frac{10}{3}S+1\right) = (2S-2) \times (S)$[/tex]

[tex]$S^2Y(S) + \frac{10}{3}(SY(S)) + Y(S) = 2(S \times (S)) - 2 \times (S)$[/tex]

Apply Inverse Laplace Transforms,

[tex]$\frac{d^2y(t)}{dt^2} + \frac{10}{3} \frac{dy(t)}{dt} + y(t)=2 \frac{dx(t)}{dt} - 2x(t)$[/tex]

The above equation represents the differential equation of transfer function.

Given : [tex]$x(t)=e^{-t} u(t) \Rightarrow X(S) = \frac{1}{S+1}$[/tex]

We have : [tex]$H(S) =\frac{Y(S)}{K(S)}= \frac{2S-2}{S^2+\left(\frac{10}{3}\right) S+1}$[/tex]

[tex]$Y(S) = X(S) \times \frac{6S-6}{3S^2+10 S + 3} = \frac{6S-6}{(S+1)(3S+1)(S+3)}$[/tex]

[tex]$Y(S) = \frac{A}{S+1}+\frac{B}{3S+1} + \frac{C}{S+3}[/tex]

[tex]$A = Lt_{S \to -1} (S+1)Y(S)=\frac{6S-6}{(3S+1)(S+3)} = \frac{-6-6}{(-3+1)(-1+3)} = 3$[/tex]

[tex]$B = Lt_{S \to -1/3} (3S+1)Y(S)=\frac{6S-6}{(S+1)(S+3)} = \frac{-6/3-6}{(1/3+1)(-1/3+3)} = \frac{-9}{2}$[/tex]

[tex]$C = Lt_{S \to -3} (S+3)Y(S)=\frac{6S-6}{(S+1)(3S+1)} = \frac{-18-6}{(-3+1)(-9+1)} = \frac{-3}{2}$[/tex]

So,

[tex]$Y(S) = \frac{3}{S+1} - \frac{9/2}{3S+1} - \frac{3/2}{S+3}$[/tex]

        [tex]$=\frac{3}{S+1} - \frac{3/2}{S+1/3} - \frac{3/2}{S+3}$[/tex]

Applying Inverse Laplace Transform,

[tex]$y(t) = 3e^{-t}u(t)-\frac{3}{2}e^{-t/3}u(t) - \frac{3}{2}e^{-3t} u(t)$[/tex]

       [tex]$=\frac{-3}{2}e^{-\frac{1}{3}t}u(t) + \frac{3}{1}e^{-t}u(t)-\frac{3}{2}e^{-3t} u(t)$[/tex]

where, a = 2

            b = 1

            c= 2

Given that the system function of a third order Butterworth type analog low-pass filter with a 3 dB cut-off frequency of 2 radian/second is:
2s HS = S2 + 0.2 s +1
Answer the following questions:
1. Use the bilinear transformation to obtain H(z). Use T=2 second.
2. Give H(w) for your filter.
3. Use MATLAB to give the magnitude spectrum.
4. Comment on the quality of the design.
5. With the aid of simple sketch graphs explain how frequency warping affects the frequency response of the digital filter.
6. Comment on the need for prewarping, i.e. give conditions when prewarping is needed.

Answers

answer

d just too the test

For a steel alloy it has been determined that a carburizing heat treatment of 3-h duration will raise the carbon concentration to 0.38 wt% at a point 2.6 mm from the surface. Estimate the time (in h) necessary to achieve the same concentration at a 6.1 mm position for an identical steel and at the same carburizing temperature.

Answers

Answer:

The right answer is "16.5 hrs".

Explanation:

Given values are:

[tex]x_1=2.6 \ mm[/tex]

[tex]t_1=3 \ hrs[/tex]

[tex]x_2=6.1 \ mm[/tex]

As we know,

⇒ [tex]\frac{x^2}{Dt}=constant[/tex]

or,

⇒ [tex]\frac{x_1^2}{t_1} =\frac{x_2^2}{t_2}[/tex]

⇒ [tex]t_2=(\frac{x_2}{x_1})^2\times t_1[/tex]

By putting the values, we get

       [tex]=(\frac{6.1}{2.6} )^2\times 3[/tex]

       [tex]=5.5\times 3[/tex]

       [tex]=16.5 \ hrs[/tex]      

Consider the equation y = 10^(4x). Which of the following statements is true?


A plot of log(y) vs. x would be linear with a slope of 4.


A plot of log(y) vs. log (x) would be linear with a slope of 10.


A plot of log(y) vs. x would be linear with a slope of 10.


A plot of y vs. log(x) would be linear with a slope of 4.


A plot of log(y) vs. log (x) would be linear with a slope of 4.


A plot of y vs. log(x) would be linear with a slope of 10.

Answers

Answer: Plot of  [tex]\log y[/tex] vs [tex]x[/tex] would be linear with a slope  of 4.

Explanation:

Given

Equation is [tex]y=10^{4x}[/tex]

Taking log both sides

[tex]\Rightarrow \log y=4x\log (10)\\\Rightarrow \log y=4x[/tex]

It resembles with linear equation [tex]y=mx+c[/tex]

Here, slope of [tex]\log y[/tex] vs [tex]x[/tex] is 4.

Draw a sinusoidal signal and illustrate how quantization and sampling is handled by
using relevant grids.

Answers

Answer: Your mums gay

Explanation: Your mums gay

Select the correct statement(s) regarding network physical and logical topologies.
a. While logical topologies can be configured in star, ring, bus, and tree configurations, the physical topology must always be in a full-mesh topology
b. logical topologies always incorporate centralized access, whereas physical topologies are always configured as a distributed access network
c. the physical topology addresses how devices are connected, while a logical topology addresses how devices actually communicate to one another
d. all statements are correct

Answers

Answer:

The physical topology addresses how devices are connected, while a logical topology addresses how devices actually communicate to one another ( C )

Explanation:

Network physical is simply the process/method of connecting the Network using cables while Logical topology is the general architecture of the communication mechanism in the network for all nodes.

Hence The correct statement is the physical topology addresses how devices are connected, while a logical topology addresses how devices actually communicate to one another

) Please label the following statements as either True (T) or False (F). (a) In general, the greater the % of cold work, the smaller the recrystallization grain size. (b) The higher the annealing temperature, the smaller the recrystallization grain size. (c) The greater the % of cold work, the lower the recrystallization temperature.

Answers

Answer:

A. This option is true

B. This option is false

C. This option is true

Explanation:

A. Generally speaking, the greater percentage of cold, the recrystallization grain size would turn out to be smaller. Therefore this true.

B. A higher annealing temperature does not result in smaller recrystallization grain size. Therefore this is false.

C. As the percentage of cold work is greater, the recrystallization temperature would tend to be lower. Therefore this is true.

Water steam enters a turbine at a temperature of 400 o C and a pressure of 3 MPa. Water saturated vapor exhausts from the turbine at a pressure of 125 kPa. At steady state, the work output of the turbine is 530 kJ/kg. The surrounding air is at 20 o C. Neglect the changes in kinetic energy and potential energy. Determine (20 points) (a) the heat transfer from the turbine to the surroundings per unit mass flow rate, (b) the entropy generation during this process.

Answers

Answer:

a) -505.229 kJ/Kg

b) -1.724 kJ/kg

Explanation:

T1 = 400°C

P1 = 3 MPa

P2 = 125 kPa

work output   = 530 kJ/kg

surrounding temperature = 20°C = 293 k

A) Calculate heat transfer from Turbine to surroundings

Q = h2 + w - h1

h ( enthalpy )

h1 = 3231.229 kj/kg

enthalpy at P2

h2 = hg = 2676 kj/kg

back to equation 1

Q = 2676 + 50 - 3231.229  = -505.229 kJ/Kg  ( i.e.  heat is lost )

b) Entropy generation

entropy generation = Δs ( surrounding )  + Δs(system)

                                =  - 505.229 / 293   + 0

                                = -1.724 kJ/kg  




Page Title





Submit



Add a pair of radio buttons to your form, each nested in its own label element.
One should have the option of car and the other should have the option of bike.
Both should share the name attribute of “vehicle” to create a radio group
Make sure the radio buttons are nested with the form
Make sure that the name attributes appear after the type

Answers

Answer:

The code is as follows:

<form name = "myForm">

       <div>

           <input type="radio" name="vehicle" value="D0" id="D0"/>

           <label for="D0">Car</label>

       </div>

       <div>

           <input type="radio" name="vehicle" value="D1" id="D1"/>

           <label for="D1">Bike</label>

       </div>

   </form>

Explanation:

This defines the first button

           <input type="radio" name="vehicle" value="D0" id="D0"/>

           <label for="D0">Car</label>

This defines the second button

           <input type="radio" name="vehicle" value="D1" id="D1"/>

           <label for="D1">Bike</label>

The code is self-explanatory, as it follows all the required details in the question

Activity 1. Fill the blank with the correct answer. Write your answer on the blank. 1. ___________________ is a regular pattern of dots displayed on the screen which acts as a visual aid and also used to define the extent of your drawing. 2. Ortho is short for ___________________, which means either vertical or horizontal. 3. Tangent is a point where two _______________________ meet at just a single point. 4. If you want to create a new drawing, simply press ___________________ for the short cut key. 5. There are _______________Osnap that can help you performs your task easier.

Answers

Answer:

1. Drawing grid.

2. Orthogonal.

3. Geometries.

4. CTRL+N.

5. Thirteen (13).

Explanation:

CAD is an acronym for computer aided design and it is typically used for designing the graphical representation of a building plan. An example of a computer aided design (CAD) software is AutoCAD.

Some of the features of an AutoCAD software are;

1. Drawing grid: is a regular pattern of dots displayed on the screen of an AutoCAD software, which acts as a visual aid and it's also used to define the extent of a drawing.

2. Ortho is short or an abbreviation for orthogonal, which means either vertical or horizontal.

3. Tangent is a point where two geometries meet at just a single point.

4. If you want to create a new drawing, simply press CTRL+N for the short cut key.

5. There are thirteen object snaps (Osnap) that can help you perform your task on AutoCAD easily. The 13 object snaps (Osnap) are; Endpoint, Midpoint, Apparent intersect, Intersection, Quadrant, Extension, Tangent, Center, Insert, Perpendicular, Node, Parallel, and Nearest.

Consider the titration of 100.0 mL of 0.200 M CH3NH2 by 0.100 M HCl.
For each volume of HCl added, decide which of the components is a major species after the HCl has reacted completely.
Kb for CH3NH2 = 4.4 x 10-4.
What species are present based off what is being added?
200.00 mL HCl added
yes no H+
yes no H2O
yes no Cl-
yes no CH3NH2
yes no CH3NH3+
300.00 mL HCl added
yes no H+
yes no H2O
yes no Cl-
yes no CH3NH2
yes no CH3NH3+
Calculate the pH at the equivalence point for this titration?

Answers

Answer:

The answers are in the explanation. The pH is 5.91

Explanation:

The CH3NH2 reacts with HCl as follows:

CH3NH2 + HCl → CH3NH3⁺ + Cl⁻

When 200mL of HCl are added, the moles of CH3NH2 and HCl are reacting completely producing CH3NH3+ and Cl-. That means the species present are:

no H+. All reacted

yes H2O. Because the water is present in the solutions of HCl and CH3NH2

yes Cl-. Is a product of the reaction

Yes CH3NH2. Is consumed in the reaction but comes from the equilibrium of CH3NH3+

yes CH3NH3+. Is the other product of the reaction. MAJOR SPECIES

When 300.00mL of HCl are added, 100mL are in excess:

yes H+. Is in excess: H+ + Cl- = HCl in water. MAJOR SPECIES. Determine the pH of the solution.

yes H2O. Is present because the reactants are diluted.  

yes Cl-. Is a product of reaction and comes from HCl.

Yes CH3NH2. The reactant is over but comes from the equilibrium of CH3NH3+

yes no CH3NH3+. Yes. Is a product and remains despite HCl is in excess.

To find the pH:

At equivalence point the ion that determines pH is CH3NH3+. Its concentration is:

0.100L * (0.200mol/L) = 0.0200 moles / 0.300L = 0.0667M CH3NH3+

The equilibrium of CH3NH3+ is:

Ka = Kw/kb = 1x10-14/4.4x10-4 = 2.273x10-11 = [H+] [CH3NH2] / [CH3NH3+]

As both [H+] [CH3NH2] comes from the same equilibrium:

[H+] =  [CH3NH2] = X

2.273x10-11 = [X] [X] / [0.0667M]

1.5159x10-12 = X²

X = 1.23x10-6M = [H+]

As pH = -log [H+]

pH = 5.91

The pH at the equivalent point for this titration is "5.91".

pH Calculation:

[tex]CH_3NH_2 = 0.200\ M\\\\ \text{volume} = 100.0\ mL = 0.100\ L\\\\HCl = 0.100\ M\\\\[/tex]

We must now quantify the pH well at the equivalence point.

We know that even at the point of equivalence, moles of acid and moles of the base are equivalent. As such, first, we must calculate the number of moles of the given base.

Calculating the Moles in [tex]CH_3NH_2 = 0.200\ M \times 0.100\ L = 0.0200\ moles[/tex]

Calculating the Moles in [tex]HCl = 0.0200 \ moles[/tex]

Calculating the volume of [tex]HCl[/tex]:

[tex]\to \text{Molarity} = \frac{ \text{moles}}{\text{volume \ (L)}} \\\\\to \text{Volume} = \frac{\text{moles}}{\text{molarity}}\\\\[/tex]

                [tex]= \frac{0.0200 \ moles}{ 0.100\ M}\\\\= 0.200 \ L\\\\= 200 \ mL\\\\[/tex]

Calculating the reaction among the acid and base:

[tex]CH_3NH_2 + HCl \longrightarrow CH_3NH_3^{+} + Cl^-[/tex]

[tex]0.0200 \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ 0.0200 \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ 0.0200[/tex]

Therefore the conjugate acid of the bases exists at the standard solution.

Then we must calculate the new molar mass of [tex]CH_3NH_3^+[/tex].

Total volume[tex]= 100 + 200 = 300\ mL = 0.300\ L[/tex]

[tex][CH_3NH_3^+] = \frac{0.0200\ mole}{ 0.300\ L}= 0.0667\ M[/tex]

Using the ICE table

[tex]CH_3NH_3^+ + H_2O \longrightarrow CH_3NH_2 + H_3O^+[/tex]

[tex]I \ \ \ \ \ \ \ \ \ \ 0.0667 \ \ \ \ \ \ \ \ \ 0\ \ \ \ \ \ \ \ \ 0\\\\C\ \ \ \ \ \ \ \ -x\ \ \ \ \ \ \ \ +x \ \ \ \ \ \ \ \ +x\\\\E \ \ \ \ \ \ \ \ \ \ \ \ 0.0667-x \ \ \ \ \ \ \ \ \ \ \ \ +x \ \ \ \ \ \ \ \ \ \ \ \+x\\\\\to Ka = \frac{[CH_3NH_2] [H_3O^+] }{[CH_3NH_3^+]}[/tex]

Calculating [tex]K_a[/tex] from [tex]K_b[/tex]

[tex]\to K_a \times K_b = 1\times 10^{-14}\\\\\to K_a = \frac{1\times 10^{-14}}{4.4\times 10^{-4}} = 2.27\times 10^{-11}\\\\[/tex]

                           [tex]= 2.27\times 10^{-11} \\\\= x\times \frac{x}{(0.0667-x)}[/tex]

The x in the 0.0667-x can be ignored since the Ka value is just too small and it also does not follow the five percent criteria.

[tex]\to 2.27 \times 10^{-11} \times 0.0667 = x_2\\\\\to x_2 = 1.515\times 10^{-12}\\\\\to x = 1.23\times 10^{-6}\ M\\\\\to [H_3O^+] = x = 1.23\times 10^{-6}\ M\\\\[/tex]

We have the formula to calculate pH.

[tex]\to pH = - \log [H_3O^+] = - \log 1.23\times 10^{-6}\ M= 5.91[/tex]

The pH at the equivalent point for this titration is "5.91".

Find out more information about the pH here:

brainly.com/question/15289741

Consider two houses that are identical, except that the walls are built using bricks in one house, and wood in the other. The walls of the brick house are twice as thick. Which house do you think will be more energy efficient?

Answers

Answer:

Walls Built Using Bricks and Wood

The brick house is more energy-efficient than the one built with wood.

Explanation:

Because of their high thermal mass, which gives bricks the ability to absorb heat and release it over time, bricks remain more energy-efficient than other building materials, including wood.  In summer, bricks leave your home cool.  In winter, they make it warm.  With these two advantages provided by bricks over other building materials, bricks are the most energy-efficient building material.

A circular rod with a gage length of 3.1 m and a diameter of 3 cm is subjected to an axial load of 68 kN . If the modulus of elasticity is 200 GPa , what is the change in length

Answers

Answer:

1.49 mm

Explanation:

The modulus of elasticity, Y = stress/strain = σ/ε

σ = F/A where F = load = 68 kN = 68 × 10³ N and A = cross-sectional area of rod = πd²/4 where d = diameter of rod = 3 cm = 3 × 10⁻² m.

ε = ΔL/L where ΔL = change in length of the circular rod and L = length of circular rod = 3.1 ,

So, Y = σ/ε

Y = F/A ÷ ΔL/L

Y = FL/AΔL

making the change in length ΔL subject of the formula, we have

ΔL = FL/AY

substituting the value of A into the equation, we have

So, ΔL = FL/(πd²/4)Y

ΔL = 4FL/πd²Y

Since Y = 200 GPa = 200 × 10⁹ Pa

Substituting the values of the variables into the equation, we have

ΔL = 4FL/πd²Y

ΔL = 4 × 68 × 10³ N × ×3.1 m/[π(3 × 10⁻²m)² × 200 × 10⁹ Pa]

ΔL = 843.2 × 10³ Nm/[9π × 10⁻⁴m² × 200 × 10⁹ Pa]

ΔL = 843.2 × 10³ Nm/[1800π × 10⁵ N]

ΔL = 843.2 × 10³ Nm/5654.87 × 10⁵ N

ΔL = 0.149 × 10⁻² m

ΔL = 1.49 × 10⁻³ m

ΔL = 1.49 mm

The change in length of the circular rod is 1.49 mm

A work-mode-choice model is developed from data acquired in the field in order to determine the probabilities of individual travelers selecting various modes. The mode choices include automobile drive-alone (DL), automobile shared-ride (SR), and bus (B). The utility functions are estimated as follows:
UDL = 2.6 - 0.3 (costDL) - 0.02 (travel timeDL)
USR = 0.7 - 0.3 (costSR) - 0.04 (travel timeSR)
UB = -0.3 (costB) - 0.01 (travel timeB)
where cost is in dollars and time is in minutes. The cost of driving an automobile is exist5.50 with a travel time of 21 minutes, while the bus fare is exist1.25 with a travel time of 27 minutes. How many people will use the shared-ride mode from a community of 4500 workers, assuming the shared-ride option always consists of three individuals sharing costs equally?
a. 314
b. 828
c. 866
d. 2805

Answers

Answer:

b. 828

Explanation:

UDL = 2.6 - 0.3 [5.5] - 0.02 [ 21 ] = 0.53

USR = 0.7 - 0.3 [5.5 / 2 ] - 0.04 [ 21 ] = -0.69

UB = -0.3 [ 1.25 ] - 0.01 = -0.645

Psr = [tex]\frac{e^{-0.53} }{e^{-0.53} + e^{-0.69} + e^{-0.645} }[/tex]

Solving the equation we get 0.184.

Number of people who will take shared ride is:

0.184 * 4500 = 828 approximately.

Calculate the scale and speed of the pattern in order to gain useful results for a turbine operate at 150 rev/min at height difference of 22 m and a predictable flow rate of 85 m per second. A scale pattern is made and examined with a volume flow rate of 0.1 m per second and a height difference of 5 m , the power value equal to 4.5 kW when checked at the speed evaluated . Predict the power and efficiency of the full size turbine .​

Answers

Answer:

first mark me as a brainleast

20 friends 6men 14 women are having a tea party

Answers

Answer:

what about it?

Explanation:

Imagine a cantilever beam fixed at one end with a mass = m and a length = L. If this beam is subject to an inertial force and a uniformly distributed load = w, what is the moment present at a length of L/4?

Answers

Answer:

jsow

hfhcffnbxhdhdhdhdhdhdddhdhdgdhdhdhdhdhdhhhdhdjsksmalalaksjdhfgrgubfghhhhhhh

Explanation:

j

grudb

Identify the first step in preparing a spectrophotometer for use.
A. Make sure all samples and the blank are ready for measurement.
B. Prepare a calibration curve.
C. Measure the absorbance of the blank.
D. Turn on the light source and the spectrophotometer.

Answers

Answer:

D. Turn on the light source and the spectrophotometer.

Explanation:

A spectrophotometer is a machine used to measure the presence of any light-absorbing particle in a solution as well as its concentration. To prepare a spectrophotometer for use, the first step is to turn on the spectrophotometer and allow it to warm up for at least 15 minutes. After this is done, the next step will be to ensure that the samples and blank are ready. Next, an appropriate wavelength is set for the solute being determined. Finally, the absorbance is measured of both the blank and samples.

A container can be made from steel [β = 36 × 10-6 (C°)-1] or lead [β = 87 × 10-6 (C°)-1]. A liquid is poured into the container, filling it to the brim. The liquid is either water [β = 207 × 10-6 (C°)-1] or ethyl alcohol [β = 1120 × 10-6 (C°)-1]. When the full container is heated, some liquid spills out. To keep the overflow to a minimum, from what should the container be made and what should the liquid be

Answers

Answer:

The container should be made of lead and the liquid should be water.

Explanation:

Since the volume of the container of liquid after expansion is V = V₀(1 + βΔθ) where V = initial volume, β = coefficient of volume expansion, Δθ = temperature change.

So, the volume change V₂ - V₁ where V₁ = volume of liquid and V₂ = volume of container

For steel, V₂ = V₀(1 + β₂Δθ) and V₁ = V₀(1 + β₁Δθ)

So, ΔV = V₀(1 + β₂Δθ) - V₀(1 + β₁Δθ) = V₀[1 + β₂Δθ - 1 - β₁Δθ] = V₀[β₂Δθ - β₁Δθ]

Since we want a minimum value for ΔV and V₀ and Δθ are the same, we need ΔV/V₀Δθ = β₂ - β₁ to be a minimum

where β₂ = coefficient of volume expansion of liquid and β₁ = coefficient of volume expansion of container.

So, trying each combination, with  β₂ = 207 × 10⁻⁶ (C°)⁻¹] and β₁ = 36 × 10⁻⁶ (C°)⁻¹

β₂ - β₁ = 207 × 10⁻⁶ (C°)⁻¹ - 36 × 10⁻⁶ (C°)⁻¹ = 171 × 10⁻⁶ (C°)⁻¹

With  β₂ = 207  × 10⁻⁶ (C°)⁻¹] and β₁ = 87  × 10⁻⁶ (C°)⁻¹

β₂ - β₁ = 207 × 10⁻⁶ (C°)⁻¹ - 87 × 10⁻⁶ (C°)⁻¹ = 120 × 10⁻⁶ (C°)⁻¹

With  β₂ = 1120 × 10⁻⁶ (C°)⁻¹] and β₁ = 36  × 10⁻⁶ (C°)⁻¹

β₂ - β₁ = 1120 × 10⁻⁶ (C°)⁻¹ - 36 × 10⁻⁶ (C°)⁻¹ = 1084 × 10⁻⁶ (C°)⁻¹

With  β₂ = 1120 × 10⁻⁶ (C°)⁻¹] and β₁ = 87 ×  10⁻⁶ (C°)⁻¹

β₂ - β₁ = 207 × 10⁻⁶ (C°)⁻¹ - 87 × 10⁻⁶ (C°)⁻¹ = 1033 × 10⁻⁶ (C°)⁻¹

The combination that gives the lowest value for β₂ - β₁ is β₂ = 207 × 10⁻⁶ (C°)⁻¹] and β₁ = 87 × 10⁻⁶ (C°)⁻¹

Since  β₁ = 87 × 10⁻⁶ (C°)⁻¹ = coefficient of expansion for lead β₂ = 207 × 10⁻⁶ (C°)⁻¹]  = coefficient of expansion for water, the container should be made of lead and the liquid should be water.

1. Add:
(i) 5xy, -2xy, -11xy, 8xy
(iv) 3a - 2b + c, 5a + 8b -70​

Answers

Answer:

(i) 0

(iv) 8a+6b+c-70

Explanation:

Hope this helps you

Other Questions
Steel chain costs $0.75 per foot from CompanyX, which provides free shipping. The samesteel chain costs $1.20 per yard at Company Y,which charges a $120.00 shipping fee for allorders. How much more does CompanyY charge, in dollars, than company X for 300feet of steel chains? A health food company makes its 'Superfood Blend' from whey protein, which costs $10.25 per pound, and powdered spirulina, which costs $22.45 per pound. The blend ends up costing $16.35 per pound. If the company has 140 pounds of the whey protein on hand, how many pounds of the spirulina does it need to get in order to make the blend? Considering your knowledge of carbohydrates, evaluate the use of chitin as a component of health foods. Partial tides _______. Question 7 options: represent various components of local tides that are resolved mathematically are predicted individually are added together to predict the height and timing of astronomical tides All of the above are correct. Only a and c are correct. 04.05 history versus fiction brainlyflvs 14. Peter needs to buy a package of pencils to write his final exam. The store offers two packages.Package 1: pack of 6 pencils for $1.68Package 2: pack of 9 pencils for $2.34Determine the cost per pencil. Which is the better deal? Round to 2 decimal places. Show all your work for full marks. (3 marks) REPOST A load of 25 kg is applied to the lower end and of a steal wire of length 25 m and thickness 3.0mm .The other end of wire is suspeded from a rigid support calculate strain and stress produced in the wire 618 000 in standard form Please helpQuadrilateral ABCD is a parallelogram. Let E be a point on AB, and let F$\ be the intersection of lines DE and BC The area of triangle EBF is 1, and the area of triangle EAD is 9. Find the area of parallelogram ABCD. The physical plant at the main campus of a large state university recieves daily requests to replace fluorescent lightbulbs. The distribution of the number of daily requests is bell-shaped and has a mean of 45 and a standard deviation of 3. Using the empirical rule, what is the approximate percentage of lightbulb replacement requests numbering between 42 and 45?Do not enter the percent symbol.ans = % What are two examples of what cultural information might be useful in specific support staff positions Please hurry due tomorrow morning!!!Jazzie and Jocelyn are racing on a track.Jazzie runs 4 miles per hour and gets a 0.25 mile head start. Jocelyn runs 0.5 miles per hour faster than Jazzie. If Jocelyn and Jazzie run the same distance, how many hours, x, do they run?F. 4x + 0.25 = 0.5xG.4x + 0.25 = 4.5xH.4x + 0.25 =3.5 xJ. 4x - 0.25 = 3.5 x Why most of the earthquakes are linked with fold mountains? What new labour-saving devices were introduced in the agricultural revolution? You move down 5 units and up 5 units. You end at (1,3). Where did you start? Can anyone describe the errors with the problems? For example the first answer is they did not distribute the negative Write the equation of the line in fully simplified slope-intercept form. Find area of the cross section of the dam pictured below Balance the following skeleton reaction and identify the oxidizing and reducing agents: Include the states of all reactants and products in your balanced equation. You do not need to include the states with the identities of the oxidizing and reducing agents. NO_2(g) rightarrow NO_3^-(aq) +NO_2^- (aq) [basic] The oxidizing agent is:______. The reducing agent is:_______. Suppose g(x) = f( x +2) - 3. Which statement best compares the graph of g(x) with the graph of f(x)? A. The graph of g(x) is shifted 2 units left and 3 units up. B. The graph of g(x) is shifted 2 units right and 3 units down. C. The graph of g(x) is shifted 2 units left and 3 units down. D. The graph of g(x) is shifted 2 units right and 3 units up.