If Vector A is (6, 4) and Vector B is (-2, -1), what is A – B?
A. (8,5)
B. (4,5)
C. (4,3)
D. (8,3)

Answer:

B has greater potential

Explanation:

We know;

Potential Energy (PE) = mgh

where, m=mass of body

g=acceleration due to gravity

h=height of body

From the formula,

PE is directly proportional to the mass of the body

so the body with greater mass has greater potential.

Answer:

7.28×10⁻⁵ T

Explanation:

Applying,

F = BILsin∅............. Equation 1

Where F = magnetic force, B = earth's magnetic field, I = current flowing through the wire, L = Length of the wire, ∅ = angle between the field and the wire.

make B the subject of the equation

B = F/ILsin∅.................. Equation 2

From the question,

Given: F = 0.16 N, I = 68 A, L = 34 m, ∅ = 72°

Substitute these values into equation 2

B = 0.16/(68×34×sin72°)

B = 0.16/(68×34×0.95)

B = 0.16/2196.4

B = 7.28×10⁻⁵ T

Answer:

(a) The spring constant is 59.23 N/m

(b) The total energy involved in the motion is 0.06 J

Explanation:

Given;

mass, m = 240 g = 0.24 kg

frequency, f = 2.5 Hz

amplitude of the oscillation, A = 4.5 cm = 0.045 m

The  angular speed is calculated as;

ω = 2πf

ω = 2 x π x 2.5

ω = 15.71 rad/s

(a) The spring constant is calculated as;

[tex]\omega = \sqrt{\frac{k}{m} } \\\\\omega ^2 = \frac{k}{m} \\\\k = m\omega ^2\\\\where;\\\\k \ is \ the \ spring \ constant\\\\k = (0.24) \times (15.71)^2\\\\k = 59.23 \ N/m[/tex]

(b) The total energy involved in the motion;

E = ¹/₂kA²

E = (0.5) x (59.23) x (0.045)²

E = 0.06 J

Answer:

The correct answer would be - Low pitch.

Explanation:

As it is known that if frequency increases then pitch will be increase as well as pitch depends on frequency, Now for the question it is mentioned that the tube closed on one end frequency is:

f = v/2l

Where,

l = length of the tube

v = velocity of longitudinal wave of gas filled in the tube

Now increase with the temperature the density of the gas decreases and velocity v is inversely proportional to density of gas so velocity increases. So if there is an increase in frequency so pitch also increases. As the temperature inside the house is at 750 F more than outsideat 450 Fso pitch is more inside and the pitch is low outside.

Answer:

Renewable energy is a type of energy that can be renewed easily, such as sunlight. By using Solar panels to collect the suns energy, we are not depleting it, so this source is renewable.

Non-renewable  energy is something that cannot easily be replenished. An example would be oil because oil takes millions of years to form and cannot be renewed easily.

The least distance up to which we can see the objects clearly without any strain is called least distance of distinct vision. Least distance of distinct vision for a normal human being is 25cm. For young people, the least distance of distant vision will be within 25cm which however it varies with age.

Answer:

25 you said ? thats incorecct

Explanation:

Answer:

solid cylinder

Explanation:

the object that arrives first is the object that has more speed, let's use the concepts of energy

starting point. Highest point

         Em₀ = U = m g h

final point. Lowest point

         Em_f = K = ½ mv² + ½ I w²

since the body has rotational and translational movement

how energy is conserved

         m g h = ½ mv² + ½ I w²

linear and angular velocity are related

          v = w r

          w = v / r

we substitute

          m g h = ½ mv² + ½ I (v/r) ²

          mg h = ½ v² (m + I /r²)

          v = [tex]\sqrt{2gh \ \frac{m}{m + \frac{I}{r^2} } }[/tex]

the tabulated moments of inertia for the bodies are

solid cylinder     I = ½ m r²

hollow cylinder  I = m r²

we look for the speed for each body

solid cylinder

          v₁ = [tex]\sqrt {2gh} \ \sqrt{\frac{m}{m + m/2} }[/tex]

          v₁ = [tex]\sqrt{2gh} \ \sqrt{2/3}[/tex]

let's call    v₀ = [tex]\sqrt{2gh}[/tex]

         v₁ = 0.816 v₀

hollow cylinder

          v₂ = [tex]\sqrt{2gh } \ \sqrt{\frac{m}{m+ m} }[/tex]

          v₂ = v₀ √½

          v₂ = 0.707 v₀

Therefore, the body that has the highest speed is the solid cylinder and since time is the inverse of speed, this is the body that spends less time to reach the bottom, that is, it is the first to arrive

Answer:

[tex]_{18}^{39} } Ar[/tex]

Explanation:

The given equation shows the disintegration of an unstable isotope of chlorine to beta particle and Argon nucleus. The nucleus undergoes the emission of a beta particle to form a more stable nucleus of Argon.

[tex]_{17} ^{39} Cl[/tex] ⇒ [tex]_{-1}^{0} e[/tex] + [tex]_{18}^{39} } Ar[/tex]

Argon is a stable gas and is found in the group 8 on the periodic table of elements.

Answer:

Answer is below

Explanation:

39 18 Ar

The length of the brass at a temperature rise of 100 K is 2.0036 m

From the question given above, the following data were obtained:

Original length (L₁) = 2 m

Temperature rise (ΔT) = 100 K

Coefficient of linear expansion (α) = 18×10¯⁶ K¯¹

The final length of the brass can be obtained as follow:

α = L₂ – L₁ / L₁ΔT

18×10¯⁶ = L₂ – 2 / (2 × 100)

18×10¯⁶ = L₂ – 2 / 200

Cross multiply

L₂ – 2 = 18×10¯⁶ × 200

L₂ – 2 = 0.0036

Collect like terms

L₂ = 0.0036 + 2

L₂ = 2.0036 m

Thus, the length of the brass at a temperature rise of 100 K is 2.0036 m

Learn more: https://brainly.com/question/21983527

Answer:

the force decreases by a factor of 4

Explanation:

The expression for the law of universal gravitation is

          F = [tex]G \frac{m_1m_2}{r^2}[/tex]

let's call the force Fo for the distance r

          F₀ = [tex]G \frac{m_1m_2}{r^2}[/tex]

They indicate that the distance doubles

          r ’= 2 r

we substitute

          F = [tex]G \frac{m_1m_2}{(r')^2}[/tex]

          F = [tex]G \frac{m_1m_2}{r^2} \ \frac{1}{4}[/tex]

          F = ¼ F₀

consequently the correct answer is that the force decreases by a factor of 4

If the distance between two large masses are doubled, the gravitational force between them weakens by a factor of 4.

Let the initial force be F

Let the initial distance apart be r

Thus, we can obtain the final force as follow:

Initial force (F₁) = F

Initial distance apart (r₁) = r

Final distance apart (r₂) = 2r

F = GM₁M₂ / r²

Fr² = GM₁M₂ (constant)

Thus,

F₁r₁² = F₂r₂²

Fr² = F₂(2r)²

Fr² = F₂4r²

Divide both side by 4r²

F₂ = Fr² /4r²

From the illustration above, we can see that when the distance (r) is doubled, the force (F) is decreased (i.e weakens) by a factor of 4

Learn more: https://brainly.com/question/975812

Answer:

An axis is an invisible line around which an object rotates, or spins. The points where an axis intersects with an object's surface are the object's North and South Poles.

Explanation:

The Earth's axis is represented by the red line. The white circle represents axial precission, the slow "wobble" of the axis.

Answer:

[tex]F_b= 0.720 N[/tex]

Explanation:

From the question we are told that:

Weight [tex]W=600N[/tex]

Average density [tex]\rho=1.20kg/m^3[/tex]

Mass

[tex]m=\frac{W}{g}[/tex]

[tex]m=\frac{600}{9.81}[/tex]

[tex]m=61.22kg[/tex]

Generally the equation for Volume is mathematically given by

[tex]V =\frac{ mass}{density}[/tex]

[tex]V= \frac{61.22}{1000}[/tex]

[tex]V=0.06122 m^3[/tex]

Therefore

Buoyant force [tex]F_b[/tex]

[tex]F_b=\rho*V*g[/tex]

[tex]F_b= rho_air*V*g[/tex]

[tex]F_b= 0.720 N[/tex]

Answer:

he is a baby art and design

Answer:

OD. The process of cutting down irrelevant information so only the information that is useful for particular purpose remains

Abstraction is the process of cutting down irrelevant information so only the information that is useful for a particular purpose remains.

Abstraction is the practice of removing anything from a set of core features by eliminating or deleting attributes.

One of the three core ideas of object-oriented programming is abstraction order to decrease complexity and maximize efficiency, a programmer uses abstraction to conceal all but the important facts about an object.

Abstraction is the process of cutting down irrelevant information so only the information that is useful for a particular purpose remains.

Hence option D is correct.

To learn more about the abstraction refer to the link;

https://brainly.com/question/13072603

Answer:

100Hz

Explanation:

In a full wave rectifier, the fundamental frequency of the ripple is twice that of input frequency. Given the input frequency of 50 Hz, the fundamental frequency will be 2 × 50 = 100Hz

Answer:

HZ 100 is the right answer hope you like it

Answer:

a. solve for a

[tex]vf ^{2} = vo ^{2} + 2a(xf - xo) \\ 2a(xf - xo) = vf^{2} - vo ^{2} \\ a = \frac{vf^{2} - vo^{2} }{2(xf - xo)} \\ a = \frac{vf ^{2} - vo ^{2} }{2xf - 2xo} [/tex]

I hope I helped you ^_^

1433 km

Explanation:

Let g' = the gravitational field strength at an altitude h

[tex]g' = G\dfrac{M_E}{(R_E + h)^2}[/tex]

We also know that g at the earth's surface is

[tex]g = G\dfrac{M_E}{R_E^2}[/tex]

Since g' = (2/3)g, we can write

[tex]G\dfrac{M_E}{(R_E + h)^2} = \dfrac{2}{3}\left(G\dfrac{M_E}{R_E^2} \right)[/tex]

Simplifying the above expression by cancelling out common factors, we get

[tex](R_E + h)^2 = \dfrac{3}{2} R_E^2[/tex]

Taking the square root of both sides, this becomes

[tex]R_E + h = \left(\!\sqrt{\dfrac{3}{2}}\right) R_E[/tex]

Solving for h, we get

[tex]h = \left(\!\sqrt{\dfrac{3}{2}} - 1\right) R_E= 0.225(6.371×10^2\:\text{km})[/tex]

[tex]\:\:\:\:\:= 1433\:\text{km}[/tex]

Answer:

28 j

Explanation:

because when you add you get 28

Answer:

A circuit with two 10 ohm resistors connected in series.

Explanation:

The formula for the equivalent resistance for resistors in parallel is

[tex]\frac{1}{Rt} = \frac{1}{R1} + \frac{1}{R2}[/tex]   So if R1=R2= 10  [tex]\frac{1}{Rt} = \frac{1}{10} + \frac{1}{10} = \frac{2}{10} <=> Rt =\frac{10}{2} =5 ohm[/tex]

The formula for the equivalent resistance for resistors in series is

Rt = R1 + R2  So Rt= 10 + 10 = 20

Answer:

10.01 cm

Explanation:

Given that,

The time delay between transmission and the arrival of the reflected wave of a signal using ultrasound traveling through a piece of fat tissue was 0.13 ms.

The average propagation speed for sound in body tissue is 1540 m/s.

We need to find the depth when the reflection occur. We know that, the distance is double when transmitting and arriving. So,

[tex]v=\dfrac{2d}{t}\\\\d=\dfrac{vt}{2}\\\\d=\dfrac{1540\times 0.13\times 10^{-3}}{2}\\\\d= $$0.1001\ m[/tex]

or

d = 10.01 cm

So, the reflection will occur at 10.01 cm.

Answer:  

t = 1.27 x 10⁹ s  

Explanation:  

First, we will find the volume of the wire:

Volume = V = AL  

where,  

A = Cross-sectional area of wire = πr² = π(1 cm)² = π(0.01 m)² = 3.14 x 10⁻⁴ m²  

L = Length of wire = 150 km = 150000 m  

Therefore,    

V = 47.12 m³

Now, we will find the number of electrons in the wire:  

No. of electrons = n = (Electrons per unit Volume)(V)  

n = (8.43 x 10²⁸ electrons/m³)(47.12 m³)  

n = 3.97 x 10³⁰ electrons  

Now, we will use the formula of current to find out the time taken by each electron to cross the wire:

[tex]I =\frac{q}{t}[/tex]  

where,  

t = time = ?  

I = current = 500 A  

q = total charge = (n)(chareg on one electron)  

q = (3.97 x 10³⁰ electrons)(1.6 x 10⁻¹⁹ C/electron)  

q = 6.36 x 10¹¹ C  

[tex]500\ A = \frac{6.36\ x\ 10^{11}\ C}{t}\\\\t = \frac{6.36\ x\ 10^{11}\ C}{500\ A}[/tex]

Therefore,

t = 1.27 x 10⁹ s

Answer: [tex]283.2\times 10^{-9}\ nC[/tex]

Explanation:

Given

Cross-sectional area [tex]A=0.4\ cm^2[/tex]

Dielectric constant [tex]k=4[/tex]

Dielectric strength [tex]E=2\times 10^8\ V/m[/tex]

Distance between capacitors [tex]d=5\ mm[/tex]

Maximum charge that can be stored before dielectric breakdown is given by

[tex]\Rightarrow Q=CV\\\\\Rightarrow Q=\dfrac{k\epsilon_oA}{d}\cdot (Ed)\quad\quad [V=E\cdot d]\\\\\Rightarrow Q=k\epsilon_oAE\\\\\Rightarrow Q=4\times 8.85\times 10^{-12}\times 0.4\times 10^{-4}\times 2\times 10^8\\\\\Rightarrow Q=28.32\times 10^{-8}\\\\\Rightarrow Q=283.2\times 10^{-9}\ nC[/tex]

Answer:

The maximum charge is 7.08 x 10^-8 C.

Explanation:

Area, A = 0.4 cm^2

K = 4

Electric field, E = 2 x 10^8 V/m

separation, d = 5 mm = 0.005 m

Let the capacitance is C and the charge is q.

[tex]q = CV\\\\q=\frac{\varepsilon o A}{d}\times E d\\\\q = \varepsilon o A E\\\\q = 8.85\times 10^{-12}\times0.4\times 10^{-4}\times 2\times 10^8\\\\q = 7.08\times 10^{-8}C[/tex]

Answer:

a) required area is 1.1318 m²

b) the maximum potential difference that can be applied across the compactor is 1931.1 V

Explanation:

Given the data in the question;

dielectric constant εr = 2.35

distance between plates ( thickness ) d = 0.0785 mm = 7.85 × 10⁻⁵ m

dielectric strength = 49.5 MV/m

a)

given that capacity capacitor C = 0.3 uF = 0.3 × 10⁻⁶ F

To find the Area, we use the following the expression.

C = ε₀εrA / d

we know that The permittivity of free space, ε₀ = 8.854 x 10⁻¹²  (F/m)

we substitute

0.3 × 10⁻⁶ = [ (8.854 x 10⁻¹²) × 2.35 × A  ] /  7.85 × 10⁻⁵

A = [ (0.3 × 10⁻⁶) × (7.85 × 10⁻⁵) ] / [ 2.35 × (8.854 x 10⁻¹²) ]

A = 2.355 × 10⁻¹¹ / 2.08069 × 10⁻¹¹

A = 1.1318 m²

Therefore, required area is 1.1318 m²

b)

the maximum potential difference that can be applied across the compactor.

We use the following expression;

⇒ 1/2 × dielectric strength × thickness d

we substitute

⇒ 1/2 × ( 49.5 × 10⁶ V/m ) × ( 7.85 × 10⁻⁵ m )

⇒ 1931.1 V

Therefore, the maximum potential difference that can be applied across the compactor is 1931.1 V

Answer:

It was an apparently temporary feature about the size of Earth, similar to the Great Red Spot of Jupiter, but disappeared within a few years.

Explanation:

The Great Dark Spot of Neptune was an immense spinning storm in the southern atmosphere of Neptune. The size of the entire Earth, it had the strongest winds ever recorded on any planet in the solar system. It was discovered by the Voyager 2 spacecraft in 1989, but by 1994 the Hubble Space Telescope saw it was gone.

The Great Red Spot is a storm found in Jupiter's southern hemisphere, with similar characteristics to the Great Dark Spot.

Answer:

Un objeto se encuentra en equilibrio físico si la fuerza neta que se le aplica es igual a 0.

En este caso solo se aplican fuerzas en el eje horizontal, por lo que las podremos sumar directamente.

La persona A aplica una fuerza:

Fa = -3N

La persona B aplica una fuerza:

Fb = 5N

La persona C aplica una fuerza Fc, la cual aún no conocemos.

Pero sabemos que la caja está en equilibrio físico, por lo que:

Fa + Fb + Fc = 0N

reemplazando los valores que conocemos, obtenemos:

-3N + 5N + Fc = 0N

Ahora podemos resolver esto para Fc, la fuerza que aplica la persona C.

Fc = 0N + 3N - 5N

Fc = -2N

Podemos concluir que la persona C aplica una fuerza horizontal de -2N

Answer:

[tex]a=2.5\ m/s^2[/tex]

Explanation:

Given that,

Initial speed of the car, u = 14 m/s

Finally, it comes to rest, v = 0

Time, t = 5.6 s

We need to find the average acceleration of the car during this time interval. We know that,

[tex]a=\dfrac{v-u}{t}\\\\a=\dfrac{0-14}{5.6}\\\\a=-2.5\ m/s^2[/tex]

So, the acceleration of the car is [tex]2.5\ m/s^2[/tex] in the opposite direction of motion.

Answer:

a) T = 0.5 s

b) v = 1.2π m/s ≈ 3.77 m/s

Explanation:

It makes two revolutions in one second so makes one revolution in ½ second

circumference of the circle is

C = 2πr = 0.6π m

which it traverses in one time period

0.6π m / 0.5 s = 1.2π m/s

To solve this, we must be knowing each and every concept related to speed and its calculations. Therefore, the angular speed of a model car moves round a circular path of radius 0.3m at 2 revolutions per secs is 3.77 m/.

Speed may be defined as the distance traveled by an item in the amount of time it requires to travel that distance. In other words, it measures how rapidly an item travels but does not provide direction.

Speed may be calculated in Science. The speed equation is a scientific formula that is used to calculate various types of speed.

Mathematically, the formula for speed can be given as

speed= distance/time

Values that are given

Time period= 0.5 s

Circumference = 2πr = 0.6π m

substituting all the given values in the above equation, we get

speed     =0.6π m / 0.5 s

On calculations, we get

              = 1.2π m/s

              =3.77 m/s

Therefore, the angular speed of a model car moves round a circular path of radius 0.3m at 2 revolutions per secs is 3.77 m/.

To learn more about speed, here:

https://brainly.com/question/13263542

#SPJ2

Answer:

3.55 T

Explanation:

Applying,

F = BILsin∅.............. Equation 1

Where F = Force, B = magnetic Field, I = current, L = Length of the wire, ∅ = Angle between the wire and the magnetic field

make B the subject of the equation

B = F/ILsin∅.................. Equation 2

From the question,

Given: F = 2.45 N, L = 3.00 cm = 0.03 m, I = 23.0 A, ∅ = 90° (Perpendicular)

Substitute these values into equation 2

B = 2.45/(0.03×23×sin90)

B = 2.45/0.69

B = 3.55 T