Match the following light concepts
- Light is bounced back at same angle
- Light penetrates medium at different angle due to different material densities
- Light bounces at different angles in periodic grid
- Light enters medium at different angles through a grid
- Light EMF field looses one axis component
A Polarized filter
B. Transmission Diffraction
C. Classical Reflection
D. Refraction
E. Reflected Diffraction

Answers

Answer 1

Answer:

- Light is bounced back at same angle    (Classical Reflection)

- Light penetrates medium at different angle due to different material densities     (Refraction)

Light bounces at different angles in periodic grid     (Reflected Diffraction)

Light enters medium at different angles through a grid     (Transmission Diffraction)

- Light EMF field looses one axis component     (Polarized filter)

Explanation:

Reflection is a phenomenon in which waves (light included) bounce back from an obstacle at the same angle of incidence

Refraction is the change in the angle of a wave as it enters the interface of two media. The change in angle is due to the difference in the densities of the two media.

Reflected diffraction occurs when an optical component with a periodic grid, splits, and diffracts light into several beams travelling in different directions. The light light bounces at an angle in the periodic grid.

Transmission diffraction is dispersion a beam of various wavelengths into a spectrum of associated lines due to the principle of diffraction. In this type of diffraction, light enters medium at different angles through a grid.

Polarized filters removes one field from the incidence electromagnetic wave like light, leaving it to vibrate in only one plane.


Related Questions

After a capacitor is fully chargerd, a small amount of current will flow though it. what is this current called?

Answers

Answer:

  leakage

Explanation:

That current is "leakage current."

Assume that the heat is transferred from the cold reservoir to the hot reservoir contrary to the Clausis statement of the second law. Prove that this violates the increase of entropy principle—as it should according to Clausius.

Answers

Answer: hello attached below is the diagram which is part of your question

Total entropy change  = entropy change in cold reservoir + entropy change in hot reservoir = -0.166 + 0.083 = -0.0837 kj/k  it violates Clausius increase of entropy which is Sgen > 0

Explanation:

Clausius statement states that it is impossible to transfer heat energy from a cooler body to a hotter body in a cycle or region without any other external factors affecting it .  

applying the increase in entropy principle to prove this

temp of cold reservoir (t hot)= 600 k

temp of hot reservoir(t cold) = 1220 k

energy (q) = 100 kj

total entropy change  = entropy change in cold reservoir + entropy change in hot reservoir = -0.166 + 0.083 = -0.0837 kj/k

entropy change in cold reservoir = Q/t cold = 100 / 600 = -0.166 kj/k

entropy change in hot reservoir = Q / t hot = 100 / 1220 = 0.083 kj/k

hence it violates  Clausius inequality of increase of entropy principle which is states that generated entropy has to be > 0

(2x+y)dx+(x-2y)dy=0 solve the differential equation

Answers

Answer: y' = - x'

Explanation:

Let f(x) = 2x + y

then f'(x) = 2 + y'

Let f(y) = x - 2y

then f'(y) = x' - 2

Given:  f'(x) + f'(y) = 0

         2 + y' + x' - 2 = 0

                y' + x'= 0

                 y' = -x'

This can also be written as:       [tex]\dfrac{dy}{dx}=-\dfrac{d}{dx}[/tex]

An AC voltage is represented by the relation v= 12. Determine the: (a) peak-to-peak voltage; (b) frequency; (c) root-mean-square voltage; (d) Period of the signal.

Answers

Answer:

The answer is below

Explanation:

An AC voltage is represented by the relation v= 12 sin(500πt). Determine the:

The equation of an AC voltage is given as:

[tex]V=V_msin(2\pi ft)[/tex]

Where Vm is the maximum value of voltage and f is the frequency

From V= 12 sin(500πt), Vm = 12, 2πft = 500πt

(a) The peak to peak voltage is total amplitude (both the negative and positive amplitude) of the voltage, it is the difference between the positive amplitude and the negative amplitude. The peak to peak voltage ([tex]V{p-p}[/tex]) is given as:

[tex]V_{p-p}=2V_m=2*12=24\ V[/tex]

b) The frequency is the number of oscillation per second. The frequency (f) is gotten from:

2πft = 500πt

2f = 500

f = 500/2

f = 250 Hz

c) The root mean square voltage is the dc value of the voltage. It is given by:

[tex]V_{rms}=\frac{V_m}{\sqrt{2} }=\frac{12}{\sqrt{2} }=8.5\ V[/tex]

d) The period (T) is the time taken to complete one oscillation, it is given by:

[tex]T=\frac{1}{f}\\ \\T=\frac{1}{250} =0.004\ s[/tex]

A rate of 0.42 minute per piece is set for a forging operation. The operator works on the job for a full eight-hour day and produces 1,500 pieces. Use a standard hour plan.

Required:
a. How many standard hours does the operator earn?
b. What is the operator's efficiency for the day?
c. If the base rate is 9.80 per hour, compute the earnings for the day.
d. What is the direct labor cost per piece at this efficiency?
e. What would be the proper piece rate (rate expressed in money) for this job, assuming that the above time standard is correct?

Answers

Answer:

b. What is the operator's efficiency for the day?

                                                      AND

e. What would be the proper piece rate (rate expressed in money) for this job, assuming that the above time standard is correct?

Explanation:

Define centrifugal pump. Give the construction and working of centrifugal pump. ​

Answers

Centrifugal pump is a hydraulic machine which converts mechanical energy into hydraulic energy by the use of centrifugal force acting on the fluid. These are the most popular and commonly used type of pumps for the transfer of fluids from low level to high level.

An ideal turbojet engine is analyzed using the cold air standard method. Given specific operating conditions determine the temperature, pressure, and enthalpy at each state, and the exit velocity.

--Given Values--
T1 (K) = 249
P1 (kPa) = 61
V1 (m/s) = 209
rp = 10.7
rc = 1.8

Required:
a. Determine the temperature (K) at state 2.
b. Determine the pressure (kPa) at state 2.
c. Determine the specific enthalpy (kJ/kg) at state 2.
d. Determine the temperature (K) at state 3.

Answers

Answer:

a.  the temperature (K) at state 2 is  [tex]\mathbf{T_2 =270.76 \ K}}[/tex]

b.  the pressure (kPa) at state 2 is   [tex]\mathtt{ \mathbf{ p_2 = 81.79 \ kPa }}[/tex]

c.  the specific enthalpy (kJ/kg) at state 2 is [tex]\mathbf{h_2 = 271.84 \ kJ/kg}}[/tex]

d.  the temperature (K) at state 3 is   [tex]\mathbf{ T_3 = 532.959 \ K}[/tex]

Explanation:

From the given information:

T1 (K) = 249

P1 (kPa) = 61

V1 (m/s) = 209

rp = 10.7

rc = 1.8

The objective is  to determine the following:

a. Determine the temperature (K) at state 2.

b. Determine the pressure (kPa) at state 2.

c. Determine the specific enthalpy (kJ/kg) at state 2.

d. Determine the temperature (K) at state 3.

To start with the specific enthalpy (kJ/kg) at state 2.

By the relation of steady -flow energy balance equation for diffuser (isentropic)

[tex]h_1 + \dfrac{V_1^2}{2}=h_2+\dfrac{V^2_2}{2}[/tex]

[tex]h_1 + \dfrac{V_1^2}{2}=h_2+0[/tex]

[tex]h_2=h_1 + \dfrac{V_1^2}{2}[/tex]

For ideal gas;enthalpy is only a function of temperature, hence [tex]c_p[/tex]T = h

where;

[tex]h_1[/tex] is the specific enthalpy at inlet  = [tex]c_pT_1[/tex]

[tex]h_2[/tex] is the specific enthalpy at  outlet = [tex]c_pT_2[/tex]

[tex]c_p[/tex]  = 1.004  kJ/kg.K or 1004 J/kg.K

Given that:

[tex]T_1[/tex] (K) = 249

[tex]V_1[/tex] (m/s) = 209

[tex]h_2=C_pT_1+ \dfrac{V_1^2}{2}[/tex]

[tex]h_2=1004 \times 249+ \dfrac{209^2}{2}[/tex]

[tex]h_2 = 249996+21840.5[/tex]

[tex]\mathbf{\mathtt{h_2 = 271836.5 \ J/kg}}[/tex]

[tex]\mathbf{h_2 = 271.84 \ kJ/kg}}[/tex]

Determine the temperature (K) at state 2.

SInce; [tex]\mathtt{h_2 = c_pT_2 = 271.84 \ kJ/kg}[/tex]

[tex]\mathtt{ c_pT_2 = 271.84 \ kJ/kg}[/tex]

[tex]\mathtt{T_2 = \dfrac{271.84 \ kJ/kg}{ c_p}}[/tex]

[tex]\mathtt{T_2 = \dfrac{271.84 \ kJ/kg}{1.004 \ kJ/kg.K}}[/tex]

[tex]\mathbf{T_2 =270.76 \ K}}[/tex]

Determine the pressure (kPa) at state 2.

For isentropic condition,

[tex]\mathtt{ \dfrac{T_2}{T_1}= \begin {pmatrix} \dfrac{p_2}{p_1} \end {pmatrix} ^\dfrac{k-1}{k}}[/tex]

where ;

k = specific heat ratio = 1.4

[tex]\mathtt{ \dfrac{270.76}{249}= \begin {pmatrix} \dfrac{p_2}{61} \end {pmatrix} ^\dfrac{1.4-1}{1.4}}[/tex]

[tex]\mathtt{ 1.087389558= \begin {pmatrix} \dfrac{p_2}{61} \end {pmatrix} ^\dfrac{0.4}{1.4}}[/tex]

[tex]\mathtt{ 1.087389558 \times 61 ^ {^ \dfrac{0.4}{1.4} }}=p_2} ^\dfrac{0.4}{1.4}}[/tex]

[tex]\mathtt{ 3.519487255=p_2} ^\dfrac{0.4}{1.4}}[/tex]

[tex]\mathtt{ \mathbf{ p_2 = \sqrt[0.4]{3.519487255^{1.4}} }}[/tex]

[tex]\mathtt{ \mathbf{ p_2 = 81.79 \ kPa }}[/tex]

d. Determine the temperature (K) at state 3.

For the isentropic process

[tex]\mathtt{\dfrac{T_3}{T_2} = \begin {pmatrix} \dfrac{p_3}{p_2} \end {pmatrix}^{\dfrac{k-1}{k}}}[/tex]

where;

[tex]\mathtt{\dfrac{p_3}{p_2} }[/tex] is the compressor ratio [tex]\mathtt{r_p}[/tex]

Given that ; the compressor ratio [tex]\mathtt{r_p}[/tex] = 10.7

[tex]\mathtt{\dfrac{T_3}{T_2} = \begin {pmatrix} r_p \end {pmatrix}^{\dfrac{k-1}{k}}}[/tex]

[tex]\mathtt{\dfrac{T_3}{270.76} = \begin {pmatrix} 10.7 \end {pmatrix}^{\dfrac{1.4-1}{1.4}}}[/tex]

[tex]\mathtt{\dfrac{T_3}{270.76} = \begin {pmatrix} 10.7 \end {pmatrix}^{^ \dfrac{0.4}{1.4}}}[/tex]

[tex]\mathtt{{T_3}{} =270.76 \times\begin {pmatrix} 10.7 \end {pmatrix}^{^ \dfrac{0.4}{1.4}}}[/tex]

[tex]\mathbf{ T_3 = 532.959 \ K}[/tex]

Where are revolved sections placed in a print? A) in between break lines B) cutting planes are used to identify their locations C) in between section lines D) stand alone

Answers

Answer:

B. Cutting planes are used to identify their locations.

Explanation:

Revolved view is a cross section view of revolved 90 degrees around a cutting plane projections. The revolved view of print will differ from a cross sectional view. It includes a line nothing the axis of revolution for the view. The correct answer is B. The revolved section in the prints has cutting planes that will be used to identify their location.

In a particular application involving airflow over a heated surface, the boundary layer temperature distribution may be approximated as

Answers

Answer:

Explanation:

In a particular application involving airflow over a heated surface, the boundary layer temperature distribution, T(y), may be approximated as:

[ T(y) - Ts / T∞ - Ts ] = 1 - e^( -Pr (U∞y / v) )

where y is the distance normal to the surface and the Prandtl number, Pr = Cpu/k = 0.7, is a dimensionless fluid property. a.) If T∞ = 380 K, Ts = 320 K, and U∞/v = 3600 m-1, what is the surface heat flux? Is this into or out of the wall? (~-5000 W/m2 , ?). b.) Plot the temperature distribution for y = 0 to y = 0.002 m. Set the axes ranges from 380 to 320 for temperature and from 0 to 0.002 m for y. Be sure to evaluate properties at the film temperature.

All hermetic compressors require a crankshaft seal.
True
False

Answers

True they are ur welcome

A cylinder is to be cast out of aluminum. The diameter of the disk is 500 mm and its thickness is 20 mm. The mold constant 2.0 sec/mm2 in Chvorinov's formula to calculate the solidification time.

Required:
a. Calculate the minimum time (minutes) for the casting to solidify.
b. Discuss if the result in part (a) is the same when casting grey cast iron.

Answers

Answer:

a) the minimum time (minutes) for the aluminium casting to solidify is 2.86 min

b) the minimum time (minutes) for the grey iron casting to solidify is 2.13 min. Therefore solidification of grey iron cast will take less time (2.13 min) compared to the solidification of the aluminium cast (2.86 min)

Explanation:

Given that; diameter of Disk = 500 mm, thickness t = 20, mold constant Cm = 2.0 sec/mm²

first we find the volume and Area;

Volume V = πD²t / 4

Volume V = π × (500)² × 20 / 4 = 3,926,991 mm³

Area A = 2πD²/ 4 + πDt

Area A = {[π × (500)²] / 2} +{ π × (500) × (20)}

Area A = 392,699.08 + 31,415.93

Area A = 424,115 mm²

a)

Chvorinov’s rule

T(aluminium) = Cm (V/A) ²

T(aluminium) =  2.0 × (3,926,991 / 424,115) ²

T(aluminium) = 171.5 s = 2.86 min

∴ the minimum time (minutes) for the casting to solidify is 2.86 min

b)

For cast iron

Cm (mold constant = 1.488 sec/mm²)

Chvorinov’s rule

T(iron) = Cm (V/A) ²

T(iron) = 1.488 × (3,926,991 / 424,115) ²

T(iron) = 127.5720s = 2.13 min

Therefore solidification of grey iron cast will take less time (2.13 min) compared to the solidification of the aluminium cast (2.86 min)

A four-cylinder four-stroke engine is modelled using the air standard Otto cycle (two engine revolutions per cycle). Given the conditions at state 1, total volume (V1) of each cylinder, compression ratio (r), rate of heat addition (Q), and engine speed in RPM, determine the efficiency and other values listed below. The gas constant for air is R =0.287 kJ/kg-K.

T1 = 300 K
P1 = 100 kPa
V1 = 500 cm^3
r = 10
Q = 60 kW
Speed = 5600 RPM

Required:
a. Determine the total mass (kg) of air in the engine.
b. Determine the specific internal energy (kJ/kg) at state 1.
c. Determine the specific volume (m^3/kg) at state 1.
d. Determine the relative specific volume at state 1.

Answers

Answer:

a) Mt = 0.0023229

b) = U1 = 214.07

c) = V₁  = 0.861 m³/kg

d) = Vr1 = 621.2

Explanation:

Given that

R = 0.287 KJ/kg.K, T1 = 300 K , P1 = 100 kPa , V1 = 500 cm³, r = 10 , Q = 60 kW , Speed N = 5600 RPM, Number of cylinders K = 4

specific heat at constant volume Cv = 0.7174 kJ/kg.K

Specific heat at constant pressure is 1.0045 Kj/kg.K

a)  To determine the total mass (kg) of air in the engine.

we say

P1V1 = mRT1

we the figures substitute

(100 x 10³) ( 500 x  10⁻⁶) = m ( 0.287 x  10³) ( 300 )

50 = m x 86100

m = 0.00005 / 86100 = 0.0005807 ( mass of one cylinder)

Total mass of 4 cylinder

Mt = m x k

Mt = 0.0005807 x 4

Mt = 0.0023229

b) To determine the specific internal energy (kJ/kg) at state 1

i.e at T1 = 300

we obtain the value of specific internal energy U1 at 300 K ( state 1) from the table ideal gas properties of air.

U1 = 214.07

c) To determine the specific volume (m³/kg) at state 1.

we say

V₁ = V1/m

V₁ = (500 x  10⁻⁶) / 0.0005807

V₁  = 0.861 m³/kg

d) To determine the relative specific volume at state 1.

To obtain the value of relative specific volume at 300 K ( i.e state 1) from the table ideal gas properties of air.

At T1 = 300 k

Vr1 = 621.2

An AC generator supplies an rms voltage of 120 V at 50.0 Hz. It is connected in series with a 0.650 H inductor, a 4.80 μF capacitor and a 301 Ω resistor.
(a) What is the impedance of the circuit?
(b) What is the rms current through the resistor?
(c) What is the average power dissipated in the circuit?
(d) What is the peak current through the resistor?
(e) What is the peak voltage across the inductor?
(f) What is the peak voltage across the capacitor?
The generator frequency is now changed so that the circuit is in resonance. What is that new (resonance) frequency?

Answers

Answer:

Explanation:

f = 50.0 Hz, L = 0.650 H, π = 3.14

C = 4.80 μF, R = 301 Ω resistor. V = 120volts

XL = wL = 2πfL

= 2×3.14×50* 0.650

= 204.1 Ohm

Xc= 1/wC

Xc = 1/2πfC

Xc = 1/2×3.14×50×4.80μF

= 1/0.0015072

= 663.48Ohms

1. Total impedance, Z = sqrt (R^2 + (Xc-XL)^2)= √ 301^2+ (663.48Ohms - 204.1 Ohm)^2

√ 90601 + (459.38)^2

√ 90601+211029.98

√ 301630.9844

= 549.209

Z = 549.21Ohms

2. I=V/Z = 120/ 549.21Ohms =0.218Ampere

3. P=V×I = 120* 0.218 = 26.16Watt

Note that

I rms = Vrms/Xc

= 120/663.48Ohms

= 0.18086A

4. I(max) = I(rms) × √2

= 0.18086A × 1.4142

= 0.2557

= 0.256A

5. V=I(max) * XL

= 0.256A ×204.1

=52.2496

= 52.250volts

6. V=I(max) × Xc

= 0.256A × 663.48Ohms

= 169.85volts

7. Xc=XL

1/2πfC = 2πfL

1/2πfC = 2πf× 0.650

1/2×3.14×f×4.80μF = 2×3.14×f×0.650

1/6.28×f×4.8×10^-6 = 4.082f

1/0.000030144× f = 4.082×f

1 = 0.000030144×f×4.082×f

1 = 0.000123f^2

f^2 = 1/0.000123048

f^2 = 8126.922

f =√8126.922

f = 90.14 Hz

After clamping a buret to a ring stand, you notice that the set-up is tippy and unstable. What should you do to stabilize the set-up

Answers

Answer:

Move the buret clamp to a ring stand with a larger base.

Explanation:

A right stand is used for titration experiments in the laboratory. It holds the burette firmly during experiments so that accurate readings can be taken.

The right stand is made up of support base, vertical stainless steel, clamp with adjustable screw that holds on to the vertical rod.

The clamp is used to hold the burette in place.

If after clamping a buret to a ring stand, you notice that the set-up is tippy and unstable, the best action will be to move the buret clamp to a ring stand with a larger base.

The larger base provides a better center of gravity and stabilises the setup

The radial component of acceleration of a particle moving in a circular path is always:________ a. negative. b. directed towards the center of the path. c. perpendicular to the transverse component of acceleration d. all of the above

Answers

Answer:

d. all of the above

Explanation:

There are two components of acceleration for a particle moving in a circular path, radial and tangential acceleration.

The radial acceleration is given by;

[tex]a_r = \frac{V^2}{R}[/tex]

Where;

V is the velocity of the particle

R is the radius of the circular path

This radial acceleration is always directed towards the center of the path, perpendicular to the tangential acceleration and negative.

Therefore, from the given options in the question, all the options are correct.

d. all of the above

There are different type of acceleration.  The radial component of acceleration of a particle moving in a circular path is always negative, directed towards the center of the path and perpendicular to the transverse component of acceleration.

Radial acceleration is simply known as the rate of change of angular velocity where the direction is towards the center about whose circumference, the body tend to shift.

This is due to because of the centripetal force. So centripetal force is the reason for a radial acceleration.

Learn more from

https://brainly.com/question/13308560

A two-lane, one-way ramp from an urban expressway with a design speed of 30 mi/h connects with a local road at a T-intersection. The turning roadway has a vertical curb on both sides. Determine the width of the turning roadway if the predominant turning vehicles are single unit trucks with some semi-trailers. Use 0.08 for super-elevation if applicable.

Answers

Answer:

30 feet

Explanation:

Given data :

design speed = 30 miles/h

super elevation = 0.08

determine the width of the turning roadway

calculate the value of R = V^2 / 15( e + p)

e = 0.08 , p = 0.2 , v = 30

R = (30)^2 / 15 ( 0.08 + 0.2 )

  = 900 / 15 ( 0.28 )

  ≈ 215 ft

pavement width from the calculation above = 28 ft

width of the turning roadway = pavement width + 2 = 30 feet ( because there are two vertical widths joining up the main road at the T junction )

1. (16 points) True or False, one point each, Write down F (false) or T (true). ___ (01) In a mechanical design, it is recommended to use standard size/dimension to overcome uncertainties in stress or material strength

Answers

Answer:

True

Explanation:

I looked it up

Answer:

true

Explanation:

You have accumulated several parking tickets while at school, but you are graduating later in the year and plan to return to your home in another jurisdiction. A friend tells you that the authorities in your home jurisdiction will never find out about the tickets when you re-register your car and apply for a new license. What should you do?

Answers

Answer:

pay off the parking tickets

Explanation:

In the scenario being described, the best thing to do would be to pay off the parking tickets. The parking tickets stay under your name, and if they are not paid in time can cause problems down the road. For starters, if they are not paid in time the amount will increase largely which will be harder to pay. If that increased amount is also not paid, then the government will suspend your licence indefinitely which can later lead to higher insurance rates.

When replacing a timing belt, many experts and vehicle manufacturers recommend that all of the following should be replaced except the

A. water pump
B. camshaft oil seal(s).
C. camshalt sprocket
D. tensioner assembly

Answers

Answer:

Correct Answer:

A. water pump

Explanation:

Timing belt in a vehicle helps to ensure that crankshaft, pistons and valves operate together in proper sequence. Timing belts are lighter, quieter and more efficient than chains that was previously used in vehicles.

Most car manufacturers recommended that, when replacing timing belt, tension assembly, water pump, camshaft oil seal should also be replaced with it at same time.

A charge is distributed uniformly along a long straight wire. The electric field 2 cm from the wire is 36 N/C. The electric field 4 cm from the wire is:

Answers

Answer:

New electric field = 18 N/C

Explanation:

Given:

Length (E1) = 2 cm

New length (E2) = 4 cm

Electric field =  36 N/C

Find:

New electric field

Computation:

New electric field = 36 [2 / 4]

New electric field = 36 [1/2]

New electric field = 18 N/C

Technician A says that when the malfunction indicator light or service engine light is on you should retrieve the diagnostic trouble code and follow the manufacturers recommended procedure. Technician B says that all obd-ll monitors must have the enabled criteria achieved before a test is performed. Who is correct?

Answers

Answer:both

Explanation:

A single-threaded power screw is 35 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 006 for the collar and 009 for the threads, while the frictional diameter of the collar is 45 mm. Find the overall efficiency and the torque to raise and lower the load for

Answers

Answer:

the torque required to RAISE the load is Tr = 18.09 Nm

the torque required to LOWER the load is Tl = 10.069 ≈ 10.07 Nm

the Overall Efficiency e = 0.2199 ≈ 0.22

Explanation:

Given that; F = 5 kN, p = 5mm, d = 35mm

Dm = d - p/2

Dm = 35 - ( 5/2) = 35 - 2.5

DM = 32.5mm

So the torque required to RAISE the load is

Tr = ( 5 × 32.5)/2 [(5 + (π × 0.09 × 32.5)) / ( (π × 32.5) - ( 0.09 × 5))] + [( 5 × 0.06 × 45)/2]

Tr = 81.25 × (14.1892 / 101.6518) + 6.75

Tr = 11.3414 + 6.75

Tr = 18.09 Nm

the torque required to LOWER the load is

Tl =  ( 5 × 32.5)/2 [(π × 0.09 × 32.5) - 5) / ( (π × 32.5) + ( 0.09 × 5))] + [( 5 × 0.06 × 45)/2]

Tl = 81.25 × 4.1892 / 102.5518 + 6.75

Tl = 3.3190 + 6.75

Tl = 10.069 ≈ 10.07 Nm

So since torque required to LOWER the load is positive

that is, the thread is self locking

Therefore the efficiency is

e = ( 5 × 5 ) / ( 2π × 18.09 )

e = 25 / 113.6628

e = 0.2199 ≈ 0.22

Strain gage is a device that senses the strain of the structure. The property of the strain gage that is used to correlate with the strain to be measured is

Answers

Answer:

  resistance

Explanation:

A strain gauge changes resistance with applied strain.

Punctuate or edit the following sentences. Your punctuation and/or revisions should reflect best TW style and grammar writing practices.
1. The author an expert in cybersecurity will speak via Zoom this Wednesday.
2. Williams' book contains many illustrations, this makes it quick reading.
3. Based on the available evidence the university administrators have opted for a hybrid format for the fall quarter which begins September 20.
4. (Thesis statement) Free laptops should be offered to all students who need them.

Answers

I inferred you want literal editing of the text above.

Explanation:

Here's a correction of the sentences:

1. The author, an expert in cybersecurity will speak via Zoom on Wednesday.

In this sentence, punctuation mark ( , ) was added and the word  'this' was replaced with 'on'.

2. Williams' book contains many illustrations, which makes it easy to read.

Added punctuation and made a revision of the sentence.

3. Based on the available evidence, the university administrators have opted for a hybrid format for the fall, which begins September 20.

Mainly added punctuations to make the senstence clarer.

4. (Thesis statement) I believe Free laptops should be offered to all students who need them.

Made a few additions.

A 400 kg machine is placed at the mid-span of a 3.2-m simply supported steel (E = 200 x 10^9 N/m^2) beam. The machine is observed to vibrate with a natural frequency of 9.3 HZ. What is the moment of inertia of the beam's cross section about its neutral axis?

Answers

Answer:

moment of inertia = 4.662 * 10^6 [tex]mm^4[/tex]

Explanation:

Given data :

Mass of machine = 400 kg = 400 * 9.81 = 3924 N

length of span = 3.2 m

E = 200 * 10^9 N/m^2

frequency = 9.3 Hz

Wm ( angular frequency ) = 2 [tex]\pi f[/tex] = 58.434 rad/secs

also Wm = [tex]\sqrt{\frac{g}{t} }[/tex]  ------- EQUATION 1

g = 9.81

deflection of simply supported beam

t = [tex]\frac{wl^3}{48EI}[/tex]

insert the value of t into equation 1

W[tex]m^2[/tex] = [tex]\frac{g*48*E*I}{WL^3}[/tex]   make I the subject of the equation

I ( Moment of inertia about the neutral axis ) = [tex]\frac{WL^3* Wn^2}{48*g*E}[/tex]

I = [tex]\frac{3924*3.2^3*58.434^2}{48*9.81*200*10^9}[/tex]  = 4.662 * 10^6 [tex]mm^4[/tex]

The natural variation of a process relative to the variation allowed by the design specifications is known as

Answers

Answer:

"Process capability" is the correct answer.

Explanation:

The Process Capability seems to be a method of measuring of how and why the framework performs concerning something like the successful objectives. This same capacity is characterized as that of the client's voice over procedure speech.Through using functionality indicators it analyses the performance with an in-control process with the permissible range.

The structure of a house is such that it loses heat at a rate of 5400 kJ/h per degree Cdifference between the indoors and outdoors. A heat pump that requires a power input of 6 kW isused to maintain this house at 21 C. Determine the lowest outdoor temperature for which the heatpump can meet the heating requirements of this house

Answers

Answer: Tl = - 13.3°C

the lowest outdoor temperature is - 13.3°C

Explanation:

Given that;

Temperature of Th = 21°C = 21 + 273 = 294 K

the rate at which heat lost is Qh = 5400 kJ/h°C

the power input to heat pump Wnet = 6 kw

The COP of a reversible heat pump depends on the temperature limits in the cycle only, and is determined by;

COPhp = Th/(Th - Tl)

COPhp = Qh/Wnet

Qh/Wnet = Th/(Th -Tl)

the amount of heat loss is expressed as

Qh = 5400/3600(294 - Tl)

the temperature of sink

( 5400/3600(294 - Tl)) / 6 = 294 / ( 294 - Tl)

now solving the equation

Tl = 259.7 - 273

Tl = - 13.3°C

so the lowest outdoor temperature is - 13.3°C

The magnitude of the normal acceleration is
A) proportional to radius of curvature.
B) inversely proportional to radius of curvature.
C) sometimes negative.
D) zero when velocity is constant.

Answers

Answer:

b. inversely proportional to radius of curvature

Explanation:

In curvilinear motions, the normal acceleration which is also called the centripetal acceleration is always directed towards the center of the circular path of motion. This acceleration has a magnitude that is directly proportional to the square of the speed of the body undergoing the motion and inversely proportional to the radius of the curvature of the motion path. The centripetal or normal acceleration a,  can be given by;

a = [tex]\frac{v^2}{r}[/tex]

Where;

v = speed of the body

r = radius of curvature.

"The transistor base-emitter voltage (VBE) a. increases with an increase in temperature. b. is not affected by temperature change. c. decreases with an increase in temperature. d. has no effect on collector current."

Answers

Answer:

C) Decreases with an increase in temperature

Explanation:

As the temperature of a transistor increases, the thermal runaway property of the transistor becomes more significant and the transistors, conducting more freely as a result of the rise in temperature, causes an increase in the collector current or leakage current. The transistor base-emitter voltage decreases as a result.

With increased heating due to heavy current flow, the transistor is damaged.

Conductivity is the reciprocal of what?

Answers

The answer is electrical resubmitted pp
Other Questions
b) How does electron gain enthalpy change along a period and in a group? On a distant planet, a ball is thrown upwards from ground level, reaching a maximum height of 12m and hitting the ground again in eight seconds. Determine a quadratic equation in the form ax^2 + bx^2+c = 0 that could be used to calculate when the ball is at a height of 3m. Do not solve the equation. solve the equation: csc(4x)-2=0 MATHEMATICSAlgebraSimultaneous Equations1. 5u + 2v=7 2u - 2v=72. 3x - 4y=19 4x - 5y=23 draft a poster highlighting the importance of staying inside our houses during the lockdown Gisele has $5.90 in quarters and nickels. If Gisele has 16 more nickels than quarters, how many quarters does she have? [I don't want the answer I just want to know how to set the problem up please] Assume Division 1 of the XYZ Company had the following results last year. Sales $5,000,000 Operating income 1,000,000 Total assets (average) 10,000,000 Current liabilities 500,000 Management's required rate of return is 8% and the weighted average cost of capital is 6%. Its effective tax rate is 30%. What is the division's economic value added? Inventory Analysis A company reports the following: Cost of goods sold $347,480 Average inventory 86,870 Determine (a) the inventory turnover and (b) the number of days' sales in inventory. Round interim calculations to the nearest dollar and final answers to one decimal place. Assume 365 days a year. There are three key reasons for putting the customer into customer solutions in selling: (1) considerable time and effort is necessary to fully understand a specific customer's requirements; (2) effective customer solutions are based on relationships among sellers and buyers; and (3) HELP DOES ANYONE KNOW THIS Why does Travis kill eckels? Explain your answer Which type style raps the text within the area that has been selected for it?A.point styleB.long linear styleC.line style D.paragraph style 1.Define Chalcolithic Age. When we say the media have the power of agenda setting or filtering, we mean that Group of answer choices the media shape which topics the government must deal with. the media can affect how people view a topic or form opinions on a topic. the media are responsible for making sure that government officials do not give in to corruption. the media should not take sides on issues if they can at all help it. Do you think it would be wrong for Luke to share information about coming releases with friends and family? Why or why not? Statistics professors believe the average number of headaches per semester for all students is more than 18. From a random sample of 15 students, the professors find the mean number of headaches is 19 and the standard deviation is 1.7. Assume the population distribution of number of headaches is normal. Whats the food chain for algae,seal lion,zooplankton,squid and salmon ocean in ionnic bonding, during the transfer of electrons between two neutrally charged atoms, one electron moves from one atom to another. What are the new relative charges between two atoms Variation in rates of cell division is regulated by a cell-cycle control systema group of molecules, mostly proteins, within a cell that coordinates the events of the cell cycle. This control system functions through a system of checkpoints. Which assessment occurs at the G2/M checkpoint? One identical unit is purchased on each of the following three dates and at the respective costs: June 1 at $10 June 2 at $15 July 4 at $20 The company sells two units during the period. Conclude which inventory items are sold first and which unit remains in ending inventory if the company is using the FIFO cost flow assumption.A. The June 1 at 10 is sold; the June 2 at $15 and July 4 at $20 remain in ending inventory.B. The June 1 at 10 and the June 2 at $15 are both sold; the July 4 unit remains in ending inventory.C. The June 2 at $15 and the July 4 at $20 are both sold; the June 1 at $10 remains in ending inventory.