Some copper wire has a resistance of 200 ohms at 20 degrees C . A current is then passed through the same wire and the temperature rises to 90 degrees C. Determine the resistance of the wire at 90 degrees correct to the nearest ohm assuming the coefficient of resistance is 0.004/degree C at 0 degrees ​

Answers

Answer 1

Answer:

256 ohms

Explanation:

Applying,

R = R'[1+α(T-T')]............. Equation 1

Where R = Final resistance of the wire, R' = Initial resistance of the wire, T = Final temperature, T' = Initial temperature, α = Temperature coefficient of resistance

From the question,

Given: R' = 200 ohms, T = 90 degrees, T' = 20 degrees, α = 0.004/degree

Substitute these values into equation 1

R = 200[1+0.004(90-20)]

R = 200[1+0.28]

R = 200(1.28)

R = 256 ohms

Answer 2

The resistance of the wire at 90 °C correct to the nearest ohm assuming the coefficient of resistance is 0.004 °C¯¹ is 256 ohm

Data obtained from the question Original resistance (R₁) = 200 ohmOriginal temperature (T₁) = 20 °C Coefficient of resistivity (α) = 0.004 °C¯¹New temperature (T₂) = 90 °C New resistance (R₂) =?

How to determine the new resistance

α = R₂ – R₁ / R₁(T₂ – T₁)

0.004 = R₂ – 200 / 200(90 – 20)

0.004 = R₂ – 200 / 200(70)

0.004 = R₂ – 200 / 14000

Cross multiply

R₂ – 200 = 0.004 × 14000

R₂ – 200 = 56

Collect like terms

R₂ = 56 + 200

R₂ = 256 ohm

Learn more about linear expansion:

https://brainly.com/question/23207743


Related Questions

if C is The vector sum of A and B C = A + B What must be true about The directions and magnitudes of A and B if C=A+B? What must be tre about the directions and magnitudes of A and B if C=0? ​

Answers

Check attached photo

Check attached photo

Answer:

Explanation:

1. If C = A + B then the lines A and B may have the same magnitude or they may not. The direction of A for example may be northwest ↖️ and the direction of B must be south ⬇️ because the arrow of A and the point of B must connect. Then C’s direction is west ⬅️ because it shouldn’t be as equilibrium.

2. If C = 0 t means the force is at equilibrium. That means all forces add up to zero. A’s direction for example may be northeast ↗️ and the direction of B may be south ⬇️ and the direction of C must be west if it has to be at equilibrium.

The magnitude of A and B must be equal

Cuando el pistón tiene un volumen de 2x10^-4 m^3, el gas en el pistón está a una presión de 150 kPa. El área del pistón es 0.00133 m^2. Calcular la fuerza que el gas ejerce sobre el embolo del pistón.

Answers

Answer:

F = 1.128 10⁸ Pa

Explanation:

Pressure is defined by

         P = F / A

If the gas is ideal for equal force eds on all the walls, so on the piston area we have

        F = P A

We reduce the pressure to the SI system

       P = 150 kpa (1000 Pa / 1kPa = 150 103 Pa

we calculate

       F = 150 10³ / 0.00133

       F = 1.128 10⁸ Pa

Two forces are acting on a body. One acts east, the other at 35° north of east. If the
two forces are equal in magnitude of 50 N, find the resultant using the Law of Sines
and the Law of Cosines. Please answer with full solution. Thanks

Answers

A=B=50NAngle=theta=35°

We know

[tex]\boxed{\sf R=\sqrt{A^2+B^2+2ABcos\Theta}}[/tex]

[tex]\\ \sf\longmapsto R=\sqrt{50^2+50^2+2(50)(50)cos35}[/tex]

[tex]\\ \sf\longmapsto R=\sqrt{2500+2500+2(2500)\times (-0.9)}[/tex]

[tex]\\ \sf\longmapsto R=\sqrt{5000+5000(-0.9)}[/tex]

[tex]\\ \sf\longmapsto R=\sqrt{5000+(-4500)}[/tex]

[tex]\\ \sf\longmapsto R=\sqrt{5000-4500}[/tex]

[tex]\\ \sf\longmapsto R=\sqrt{-500}[/tex]

[tex]\\ \sf\longmapsto R=22.4i[/tex]

Resultant using the Law of Sines and the Law of Cosines will be R=95 N

What is force?

Force is an external agent applied on any object to displace it from its position. Force is a vector quantity, so with magnitude it also requires direction. Direction is necessary to examine the effect of the force and to find the equilibrium of the force.

The Magnitude of two forces =50 N

Angle between the forces = 35

By using the resultant formula

[tex]\rm R=\sqrt{A^2+B^2+2ABCos\theta}[/tex]

[tex]\rm R=\sqrt{50^2+50^2+2(50)(50)Cos35}[/tex]

[tex]\rm R=\sqrt{5000+5000(0.81)}[/tex]

[tex]\rm R=\sqrt{5000+4500}[/tex]

[tex]\rm R=95\ N[/tex]

Hence the Resultant using the Law of Sines and the Law of Cosines will be R=95 N

To know more about force follow

https://brainly.com/question/25239010

. A ball of mass 0.50 kg is rolling across a table top with a speed of 5.0 m/s. When the ball reaches the edge of the table, it rolls down an incline onto the floor 1.0 meter below (without bouncing). What is the speed of the ball when it reaches the floor?

Answers

Answer:

4

Explanation:

Choose one. 5 points
Use the equation from week 3:
frequency =
wavespeed
wavelength
and the wavelength you found in #3 to calculate the frequency of this photon (remember the speed of
light is 3E8 m/s);
7.6E14 Hz
6.0E14 Hz
4,6E14 Hz

Answers

Is 4,6E14 Hz
Good luck

The frequency is 4,6E14 Hz.

What is the frequency?

Frequency is the fee at which modern changes direction in step with 2nd. it's far measured in hertz (Hz), a worldwide unit of degree wherein 1 hertz is identical to 1 cycle in line with 2d. Hertz (Hz) = One hertz is the same as 1 cycle in step with the second. Cycle = One entire wave of alternating present-day voltage.

Frequency describes the number of waves that pass a hard and fast place in a given quantity of time. So if the time it takes for a wave to skip is half of 2d, the frequency is 2 per 2nd. If it takes 1/one hundred of an hour, the frequency is a hundred in step with hour.

Learn more about frequency here:-https://brainly.com/question/254161

#SPJ2

The paper dielectric in a paper-and-foil capacitor is 0.0785 mm thick. Its dielectric constant is 2.35, and its dielectric strength is 49.5 MV/m. Assume that the geometry is that of a parallel-plate capacitor, with the metal foil serving as the plates.

Required:
a. What area of each plate is required for for a 0.300 uF capacitor?
b. If the electric field in the paper is not to exceed one-half the dielectric strength, what is the maximum potential difference that can be applied across the compactor?

Answers

Answer:

a) required area is 1.1318 m²

b) the maximum potential difference that can be applied across the compactor is 1931.1 V

Explanation:

Given the data in the question;

dielectric constant εr = 2.35

distance between plates ( thickness ) d = 0.0785 mm = 7.85 × 10⁻⁵ m

dielectric strength = 49.5 MV/m

a)

given that capacity capacitor C = 0.3 uF = 0.3 × 10⁻⁶ F

To find the Area, we use the following the expression.

C = ε₀εrA / d

we know that The permittivity of free space, ε₀ = 8.854 x 10⁻¹²  (F/m)

we substitute

0.3 × 10⁻⁶ = [ (8.854 x 10⁻¹²) × 2.35 × A  ] /  7.85 × 10⁻⁵

A = [ (0.3 × 10⁻⁶) × (7.85 × 10⁻⁵) ] / [ 2.35 × (8.854 x 10⁻¹²) ]

A = 2.355 × 10⁻¹¹ / 2.08069 × 10⁻¹¹

A = 1.1318 m²

Therefore, required area is 1.1318 m²

b)

the maximum potential difference that can be applied across the compactor.

We use the following expression;

⇒ 1/2 × dielectric strength × thickness d

we substitute

⇒ 1/2 × ( 49.5 × 10⁶ V/m ) × ( 7.85 × 10⁻⁵ m )

1931.1 V

Therefore, the maximum potential difference that can be applied across the compactor is 1931.1 V

In a large chemical factory, a feed pipe carries a liquid at a speed of 5.5 m/s. A pump pushes the liquid along at a gauge pressure of 140,000 Pa. The liquid travels upward 6.0 m and enters a tank at a gauge pressure of 2,000 Pa. The diameter of the pipe remains constant. At what speed does the liquid enter the tank

Answers

Answer:

v₂ = 15.24 m / s

Explanation:

This is an exercise in fluid mechanics

Let's write Bernoulli's equation, where the subscript 1 is for the factory pipe and the subscript 2 is for the tank.

          P₁ + ½ ρ v₁² + ρ g y₁ = P₂ + ½ ρ v₂² + ρ g y₂

They indicate the pressure in the factory P₁ = 140000 Pa, the velocity

v₁ = 5.5 m / s and the initial height is zero y₁ = 0

the tank is at a pressure of P2 = 2000 Pa and a height of y₂ = 6.0 m

          P₁ -P₂ + ρ g (y₁ -y₂) + ½ ρ v₁² = ½ ρ v₂²

           

let's calculate

         140,000 - 2000 + ρ 9.8 (0- 6) + ½ ρ 5.5² = ½ ρ v₂²

         138000 - ρ 58.8 + ρ 15.125 = ½ ρ v2²

         v₂² = 2 (138000 /ρ - 58.8 + 15.125)

         v₂ = [tex]\sqrt{\frac{276000}{\rho } - 43.675 }[/tex]

In the exercise they do not indicate what type of liquid is being used, suppose it is water with

           ρ = 1000 kg / m³

           v₂ = [tex]\sqrt{\frac{276000}{1000} - 43.675}[/tex]

           v₂ = 15.24 m / s

A man standing in an elevator holds a spring scale with a load of 5 kg suspended from it. What would be the reading of the scale, if the elevator is accelerating downward with an acceleration 3.8 m/s?.

Answers

Answer:

3.1 kg

Explanation:

Applying,

R = m(g-a)..................... Equation 1

Where R = weight of the scale when the elevator is coming down, a = acceleration of the elevator, g = acceleration due to gravith.

From the question,

Given: m = 5 kg, a = 3.8 m/s²

Constant: g = 9.8 m/s²

Substitute these values into equation 1

R = 5(9.8-3.8)

R = 5(6)

R = 30 N

Hence the spring scale is

m' = R/g

m' = 30/9.8

m' = 3.1 kg

the rate of cooling determines ....... and ......​

Answers

Answer:

freezing point and melting point

Why we use semiconductor instead of metal in thermopile.

Answers

Answer:

Semiconductors are not normal materials. They have special properties which conductors/metals cannot exhibit. The main reason for the behavior of semiconductors is that they have paired charge carriers-the electron-hole pair. This is not available in metals.

An infinite plane lies in the yz-plane and it has a uniform surface charge density.
The electric field at a distance x from the plane
a.) decreases as 1/x^2
b.) increases linearly with x
c.) is undertermined
d.) decreases linearly with x
e.) is constant and does not depend on x

Answers

Answer:

So the correct answer is letter e)

Explanation:

The electric field of an infinite yz-plane with a uniform surface charge density  (σ) is given by:

[tex]E=\frac{\sigma }{2\epsilon_{0}}[/tex]

Where ε₀ is the electric permitivity.

As we see, this electric field does not depend on distance, so the correct answer is letter e)

I hope it helps you!

the plane of a 5.0 cm by 8.0 cm rectangular loop wire is parallel to a 0.19 t magnetic field. if the loop carries a current of 6.2 amps, what is the magnitude of the torque on the loop

Answers

here is the state ment :0.2 loop

A space ship has four thrusters positioned on the top and bottom, and left and right as shown below. The thrusters can be operated independently or together to help the ship navigate in all directions.
Initially, the Space Probe is floating towards the East, as shown below, with a velocity, v. The pilot then turns on thruster #2.

Select one:

a.
Space ship will have a velocity to the West and will be speeding up.

b.
Space ship will have a velocity to the East and will be speeding up.

c.
Space ship will have a velocity to the East and will be slowing down.

d.
Space ship will have a velocity to the West and will be slowing down.

e.
Ship experiences no change in motion.

Answers

Answer:

The correct answer is - c.  Spaceship will have a velocity to the East and will be slowing down.

Explanation:

In this case, if turned on thruster #2 then it will exert force on the west side as thruster 2 is on the east side and it can be understood by Newton's third law that says each action has the same but opposite reaction.

As the spaceship engine applies force on the east side then according to the law the exhauster gas applies on towards west direction. It will try to decrease the velocity of the spaceship however, the direction of floating still be east side initally.

Rays of light coming from the sun (a very distant object) are near and parallel to the principal axis of a concave mirror. After reflecting from the mirror, where will the rays cross each other at a single point?
The rays __________
a. will not cross each other after reflecting from a concave mirror.
b. will cross at the center of curvature.
c. will cross at the point where the principal axis intersects the mirror.
d. will cross at the focal point. will cross at a point beyond the center of curvature.

Answers

A concave mirror is an example of curved mirrors. So that the appropriate answer to the given question is option D. The rays will cross at the focal point.

A concave mirror is a type of mirror in which its inner part is the reflecting surface, while its outer part is the back of the mirror.  This mirror reflects all parallel rays close to the principal axis to a point of convergence. It can also be referred to as the converging mirror.

In this type of mirror, all rays of light parallel to the principal axis of the mirror after reflection will cross at the focal point.

Therefore, the required answer to the given question is option D. i.e The rays will cross at the focal point.

For reference: https://brainly.com/question/20380620

During a particular thunderstorm, the electric potential difference between a cloud and the ground is Vcloud - Vground = 4.20 108 V, with the cloud being at the higher potential. What is the change in an electron's electric potential energy when the electron moves from the ground to the cloud?

Answers

Answer:

The electric potential energy is 6.72 x 10^-11 J.

Explanation:

Potential difference, V = 4.2 x 10^8 V

charge of electron, q = - 1.6 x 10^-19 C

Let the potential energy is U.

U = q V

U = 1.6 x 10^-19 x 4.2 x 10^8

U = 6.72 x 10^-11 J

Q)what are convex mirrors?​

Answers

Answer:

A curved mirror is a mirror with a curved reflecting surface. The surface may be either convex or concave. Most curved mirrors have surfaces that are shaped like part of a sphere, but other shapes are sometimes used in optical devices.

A convex mirror (or lens) is one constructed so that it is thicker in the middle than it is at the edge.

What is the volume of a metal block 3cm long by 2cm wide by 4cm high? What would be the volume of a block twice as long, wide, and high?

Answers

Answer:

Volume of a metal block = 24 cm^3

Volume of a block twice as long, wide and high = 192 cm^3

Explanation:

Volume of a block is measured in l*w*h and in the first block, the sides are 3, 2 and 4 and 3*2*4 = 24

Second block, just double each of the lengths to get 6*4*8 = 192

Two identical cars, each traveling at 16 m>s, slam into a concrete wall and come to rest. In car A the air bag does not deploy and the driver hits the steering wheel; in car B the driver contacts the deployed air bag. (a) Is the impulse delivered by the steering wheel to driver A greater than, less than, or equal to the impulse delivered by the air bag to driver B

Answers

Answer:

 I = - m 16  the two impulses are the same,

Explanation:

The impulse is given by the relationship

         I = Δp

         I = p_f - p₀

in this case the final velocity is zero therefore p_f = 0

        I = -p₀

For driver A the steering wheel impulse is

        I = - m v₀

        I = - m 16

For driver B, the airbag gives an impulse

        I = - m 16

We can see that the two impulses are the same, the difference is that in the air bag more time is used to give this impulse therefore the force on the driver is less

When the drag force on an object falling through the air equals the force of gravity, the object has reached
terminal force.
terminal acceleration,
terminal illness.
terminal velocity

Answers

The answer is terminal force

derive expression for pressure exerted by gas ​

Answers

From kinetic theory of gases, the pressure exerted by a gas is given by velocity of gas molecules. m = Mass of each molecule of a gas. But by assumptions of the kinetic theory of gases the average kinetic energy of a molecule is constant at a constant temperature.

A 12.0 g sample of gas occupies 19.2 L at STP. what is the of moles and molecular weight of this gas?​

Answers

At STP, 1 mole of an ideal gas occupies a volume of about 22.4 L. So if n is the number of moles of this gas, then

n / (19.2 L) = (1 mole) / (22.4 L)   ==>   n = (19.2 L•mole) / (22.4 L) ≈ 0.857 mol

If the sample has a mass of 12.0 g, then its molecular weight is

(12.0 g) / n14.0 g/mol

One charge is fixed q1 = 5 µC at the origin in a coordinate system, a second charge q2 = -3.2 µC the other is at a distance of x = 90 m from the origin.

What is the potential energy of this pair of charges?

Answers

Answer:

5.4uC

Explanation:

A 1.5kg block slides along a frictionless surface at 1.3m/s . A second block, sliding at a faster 4.3m/s , collides with the first from behind and sticks to it. The final velocity of the combined blocks is 2.0m/s . What was the mass of the second block?

Answers

Answer:

The mass of the second block=0.457 kg

Explanation:

We are given that

m1=1.5 kg

v1=1.3m/s

v2=4.3 m/s

V=2.0 m/s

We have to find the mass of the second block.

[tex]m_1v_1+m_2v_2=(m_1+m_2)V[/tex]

Let m2=m

Substitute the values

[tex]1.5(1.3)+m(4.3)=(1.5+m)(2)[/tex]

[tex]1.95+4.3m=3+2m[/tex]

[tex]4.3m-2m=3-1.95[/tex]

[tex]2.3m=1.05[/tex]

[tex]m=\frac{1.05}{2.3}[/tex]

[tex]m=0.457 kg[/tex]

Hence,  the mass of the second block=0.457 kg

Nhiệt dung riêng của một chất là ?

Answers

Answer:

enchantment table language

Explanation:

enchantment Language table

A 20 N south magnetic force pushes a charged particle traveling with a velocity of 4 m/s west through a 5 T magnetic field pointing downwards . What is the charge of the particle ?

Answers

Answer:

Charge of the particle is 1 coulomb.

Explanation:

Force, F:

[tex]{ \bf{F=BeV}}[/tex]

F is magnetic force.

B is the magnetic flux density.

e is the charge of the particle.

V is the velocity

[tex]{ \sf{20 = (5 \times e \times 4)}} \\ { \sf{20e = 20}} \\ { \sf{e = 1 \: coulomb}}[/tex]

5. Steve is driving in his car to take care of some errands. The first errand has him driving to a location 2 km East and 6 km North of his starting location. Once he completes that errand, he drives to the second one which is 4 km East and 2 km South of the first errand. What is the magnitude of the vector that describes how far the car has traveled from its starting point, rounded to the nearest km?​

Answers

Answer:

gshshs

Explanation:

hshsksksksbsbbshd

A cylinder is given a push and then rolls up an inclined plane. If the origin is the starting point, sketch the position, velocity, and acceleration of the cylinder vs. time as it goes up and then down the plane.

Answers

It will take a shorter amount of time for the cylinder to go down the plane down off the plane Because more pressure is applied one going up then going down there’s no pressure at all it’s the gravity is helping

In the diagram, the crest of the wave is show by:
A
B
C
D

Answers

Answer:

D.

Explanation:

The crest of a wave refers to the highest point of a wave. This is illustrated by D.

i don't understand this, can someone help please?? ​

Answers

Explanation:

N2 + H2 --> NH3

balance them:

N2 + 3 H2 --> 2 NH3

so if 6 moles of N2 react, 12 moles of NH3 will form.

(you have to look at the big number in front, in this case its N2 and 2 NH3, therefore the amount of N2 will produce double the amount of NH3 )

The time delay between transmission and the arrival of the reflected wave of a signal using ultrasound traveling through a piece of fat tissue was 0.13 ms. At what depth did this reflection occur? (The average propagation speed for sound in body tissue is 1540 m/s)

Answers

Answer:

10.01 cm

Explanation:

Given that,

The time delay between transmission and the arrival of the reflected wave of a signal using ultrasound traveling through a piece of fat tissue was 0.13 ms.

The average propagation speed for sound in body tissue is 1540 m/s.

We need to find the depth when the reflection occur. We know that, the distance is double when transmitting and arriving. So,

[tex]v=\dfrac{2d}{t}\\\\d=\dfrac{vt}{2}\\\\d=\dfrac{1540\times 0.13\times 10^{-3}}{2}\\\\d= $$0.1001\ m[/tex]

or

d = 10.01 cm

So, the reflection will occur at 10.01 cm.

Other Questions
pls answer this question i think easy Cuando el pistn tiene un volumen de 2x10^-4 m^3, el gas en el pistn est a una presin de 150 kPa. El rea del pistn es 0.00133 m^2. Calcular la fuerza que el gas ejerce sobre el embolo del pistn. Simplify the complex number -16+8. What are some reasons adults should read fairy tales? Reasons I've already listed:-Can encourage creativity-Can teach lifelong lessonsI need one more! Help ! With step by step solution why are ghost always hungry? Triangle DEF has sides of length x, x+3, and x1. What are all the possible types of DEF? A space ship has four thrusters positioned on the top and bottom, and left and right as shown below. The thrusters can be operated independently or together to help the ship navigate in all directions.Initially, the Space Probe is floating towards the East, as shown below, with a velocity, v. The pilot then turns on thruster #2.Select one:a.Space ship will have a velocity to the West and will be speeding up.b.Space ship will have a velocity to the East and will be speeding up.c.Space ship will have a velocity to the East and will be slowing down.d.Space ship will have a velocity to the West and will be slowing down.e.Ship experiences no change in motion. write the professional education of :i. JTAii. Foresteriii. Ranger ng vua u tin ca nc php l ai ? Q)what are convex mirrors? Help please!??!!?!? 6. Which is NOT a complete sentence?I smell the flowers.Tammy bought a purse today.Red and blue socks in her room.Did you eat breakfast?N Answer it please Fubuki drives 18.4 miles in 16 minutes. He passes a sign which gives the speed limit as 60 mph. By how much, in mph, did Fubuki's average speed exceed the speed limit? Jupiter has just under 70 documented moons, .............. four largest of which are the Galilean moons Io, Callisto, Ganymede and Europa.santhe What are the advantages of Radio waves over micro waves? About how many people were killedby the atomic bomb in Nagasaki?A. 200,000B. 75,000C. 300,000 Somebody can help me please Write the fraction or mixed number as a decimal. Need help asapppppppppp