The atomic number of a nucleus increases during which nuclear reactions?

Answer:

     e% = 0.99%   this value is within the 5% tolerance given by the manufacturer

Explanation:

Modern manufacturing methods establish a tolerance in order to guarantee homogeneous characteristics in their products, in the case of resistors the tolerance or error is given by

          e% = | R_nominal - R_measured | / R_nominal 100

where R_nominal is the one written in the resistance in your barcode, R_measured is the real value read with a multimeter and e% is the tolerance also written in the resistors

let's apply this formula to our case

R_nominal = 10 kΩ = 10000 Ω

R_measured = 100 99 Ω

        e% = | 10000 - 10099.1 | / 10000 100

        e% = 0.99%

this value is within the 5% tolerance given by the manufacturer

Answer:

The potential will be Va/b

Explanation:

So Let sphere A charged Q to potential V.

so, V= KQ/a. ....(1

Thus, spherical shell B is connected to the sphere A by a wire, so all charge always reside on the outer surface.

therefore, potential will be ,

V ′ = KQ/b = Va/b... That is from .....(1), KQ=Va]

Answer:

The magnitude of the average induced emf is 90V

Explanation:

Given;

area of the square coil, A = 0.4 m²

number of turns, N = 15 turns

magnitude of the magnetic field, B = 0.75 T

time of change of magnetic field, t = 0.05 s

The magnitude of the average induced emf is given by;

E = -NAB/t

E = -(15 x 0.4 x 0.75) / 0.05

E = -90 V

|E| = 90 V

Therefore, the magnitude of the average induced emf is 90V

Answer:

The emerging intensity is equal to 0.75[tex]I_{o}[/tex]

Explanation:

The initial intensity of the light = [tex]I_{o}[/tex]

The angle of polarization β = 30°

We know that the polarized light intensity is related to the initial light intensity by

[tex]I[/tex] = [tex]I_{0} cos^{2}\beta[/tex]

where [tex]I[/tex] is the emerging polarized light intensity

inserting values gives

[tex]I[/tex] = [tex]I_{0} cos^{2}[/tex] 30°

[tex]cos^{2}[/tex] 30° = [tex](cos 30)^{2}[/tex] = [tex](\frac{\sqrt{3} }{2} )^{2}[/tex] = 0.75

[tex]I[/tex] = 0.75[tex]I_{o}[/tex]

Answer:

Explanation:

From the figure , it is clear that moment of tension is balanced by moment of weight of plate about the line AB which is acting as axis . If W be the weight of plate ,

moment of tension about AB = moment of weight W about line AB

= W x 2.5 cosθ

moment of tension about AB = 2.5 W cosθ

here only variable  is cosθ which changes when θ changes

So, moment of tension about AB varies according to cosθ.

When θ = 0

moment of tension about AB = 2.5 W x cos 0 = 2.5 W . It is the maximum value of moment of tension .

When θ = 90°

moment of tension about AB = 2.5 W cos 90 = 0

moment of tension about AB = 0

So graph of moment of tension about AB will vary according to graph of

cosθ . It has been shown in the file attached .

Answer:

[tex]\boxed{\sf 65.3 \ inches}[/tex]

Explanation:

1 foot = 12 inches

Sammy is 5 feet tall.

5 feet = ? inches

Multiply the feet value by 12 to find in inches.

5 × 12

= 60

Add 5.3 inches to 60 inches.

60 + 5.3

= 65.3

Answer:

f. 80 and 90

Explanation:

1 x 10⁻¹² W/m² sound intensity falls within 0 sound level

1 x 10⁻¹¹ W/m² sound intensity falls within 10 sound level

1 x 10⁻¹⁰ W/m² sound intensity falls within 20 sound level

1 x 10⁻⁹ W/m² sound intensity falls within 30 sound level

1 x 10⁻⁸ W/m² sound intensity falls within 40 sound level

1 x 10⁻⁷ W/m² sound intensity falls within 50 sound level

1 x 10⁻⁶ W/m² sound intensity falls within 60 sound level

1 x 10⁻⁵ W/m² sound intensity falls within 70 sound level

1 x 10⁻⁴ W/m² sound intensity falls within 80 sound level

1 x 10⁻³ W/m² sound intensity falls within 90 sound level

Given sound intensity (3.66 x 10⁻⁴ W/m²) falls with 1 x 10⁻⁴ W/m² of intensity which is within 80 and 90 sound level.

f. 80 and 90

Answer:

The wavelength is  [tex]\lambda = 589 nm[/tex]

Explanation:

From the question we are told that

    The  distance of the mirror shift  is  [tex]k = 0.233 \ mm = 0.233*10^{-3} \ m[/tex]

      The number of fringe shift is  n =  792

Generally the wavelength producing this fringes is mathematically represented as

               [tex]\lambda = \frac{ 2 * k }{ n }[/tex]

substituting values

              [tex]\lambda = \frac{ 2 * 0.233*10^{-3} }{ 792 }[/tex]

             [tex]\lambda = 5.885 *10^{-7} \ m[/tex]

            [tex]\lambda = 589 nm[/tex]

Answer:

Explanation:

change in magnetic flux = .16 x .16 x .510 - 0

= .013056 weber .

rate of change of flux = change in flux / time

= .013056 / 40.5 x 10⁻³

= .32237

voltage induced = .32237 V

electrical energy dissipated = v² / R where v is voltage , R is resistance

= .32237² / 6.35

= 16.36 x 10⁻³ J .

Answer:

The speed of the electron is 1.371 x 10⁶ m/s.

Explanation:

Given;

wavelength of the ultraviolet light beam, λ = 130 nm = 130 x 10⁻⁹ m

the work function of the molybdenum surface, W₀ = 4.2 eV = 6.728 x 10⁻¹⁹ J

The energy of the incident light is given by;

E = hf

where;

h is Planck's constant = 6.626 x 10⁻³⁴ J/s

f = c / λ

[tex]E = \frac{hc}{\lambda} \\\\E = \frac{6.626*10^{-34} *3*10^{8}}{130*10^{-9}} \\\\E = 15.291*10^{-19} \ J[/tex]

Photo electric effect equation is given by;

E = W₀ + K.E

Where;

K.E is the kinetic energy of the emitted electron

K.E = E - W₀

K.E = 15.291 x 10⁻¹⁹ J - 6.728 x 10⁻¹⁹ J

K.E = 8.563 x 10⁻¹⁹ J

Kinetic energy of the emitted electron is given by;

K.E = ¹/₂mv²

where;

m is mass of the electron = 9.11 x 10⁻³¹ kg

v is the speed of the electron

[tex]v = \sqrt{\frac{2K.E}{m} } \\\\v = \sqrt{\frac{2*8.563*10^{-19}}{9.11*10^{-31}}}\\\\v = 1.371 *10^{6} \ m/s[/tex]

Therefore, the speed of the electron is 1.371 x 10⁶ m/s.

Answer:

No, a rigid body cannot experience any acceleration when the resultant force acting on the body is zero.

Explanation:

If the net force on a body is zero, then it means that all the forces acting on the body are balanced and cancel out one another. This sate of equilibrium can be static equilibrium (like that of a rigid body), or dynamic equilibrium (that of a car moving with constant velocity)

For a body under this type of equilibrium,

ΣF = 0   ...1

where ΣF is the resultant force (total effective force due to all the forces acting on the body)

For a body to accelerate, there must be a force acting on it. The acceleration of a body is proportional to the force applied, for a constant mass of the body. The relationship between the net force and mass is given as

ΣF = ma   ...2

where m is the mass of the body

a is the acceleration of the body

Substituting equation 2 into equation 1, we have

0 = ma

therefore,

a = 0

this means that if the resultant force acting on a rigid body is zero, then there won't be any force available to produce acceleration on the body.

Answer:

A

 [tex]\lambda = 361.45 \ m[/tex]

B

[tex]k = 0.01739 \ rad/m[/tex]

C

 [tex]w = 5.22 *10^{6} \ rad/s[/tex]

D

[tex]E = 0.01446 \ N/C[/tex]

Explanation:

From the question we are told that

   The frequency is [tex]f = 83 0 \ kHz = 830 *10^{3} \ Hz[/tex]

    The  magnetic field amplitude is  [tex]B = 4.82*10^{-11} \ T[/tex]

Generally wavelength is mathematically represented as

        [tex]\lambda = \frac{c}{f}[/tex]

where c is the speed of light with value  [tex]c = 3.0*10^{8} \ m/s[/tex]

     =>  [tex]\lambda = \frac{3.0*10^{8}}{ 830 *10^{3}}[/tex]

     =>  [tex]\lambda = 361.45 \ m[/tex]

Generally the wave number is mathematically represented as

        [tex]k = \frac{2 \pi }{\lambda }[/tex]

=>     [tex]k = \frac{2 * 3.142 }{ 361.45 }[/tex]

=>    [tex]k = 0.01739 \ rad/m[/tex]

Generally the angular frequency is mathematically represented as

     [tex]w = 2 * \pi * f[/tex]

=>  [tex]w = 2 * 3.142 * 830*10^{3}[/tex]

=>   [tex]w = 5.22 *10^{6} \ rad/s[/tex]

The the electric-field amplitude is mathematically represented as

     [tex]E = B * c[/tex]

=>    [tex]E = 4.82 *10^{-11} * 3.0*10^{8}[/tex]

=>     [tex]E = 0.01446 \ N/C[/tex]

This question involves the concepts of wavelength, frequency, wave number, and electric field.

a) The wavelength is "361.44 m".

b) The wave number is "0.0028 m⁻¹".

c) The angular frequency is "5.22 x 10⁶ rad/s".

d) The electric field amplitude is "0.0145 N/C".

a)

The wavelength can be given by the following formula:

[tex]c=f\lambda[/tex]

where,

c = speed of light = 3 x 10⁸ m/s

f = frequency = 830 KHz = 8.3 x 10⁵ Hz

λ = wavelength = ?

Therefore,

[tex]3\ x\ 10^8\ m/s=(8.3\ x\ 10^5\ Hz)\lambda\\\\\lambda=\frac{3\ x\ 10^8\ m/s}{8.3\ x\ 10^5\ Hz}\\\\[/tex]

λ = 361.44 m

b)

The wave number can be given by the following formula:

[tex]wave\ number = \frac{1}{\lambda} = \frac{1}{361.44\ m}[/tex]

wave number = 0.0028 m⁻¹

c)

The angular frequency is given as follows:

[tex]\omega = 2\pi f = (2)(\pi)(8.3\ x\ 10^5\ Hz)[/tex]

ω = 5.22 x 10⁶ rad/s

d)

The electric field amplitude can be given by the following formula:

[tex]\frac{E}{B} = c\\\\c(B)=E\\\\E = (3\ x\ 10^8\ m/s)(4.82\ x\ 10^{-11}\ T)\\[/tex]

E = 0.0145 N/C

Learn more about wavelength and frequency here:

https://brainly.com/question/12924624?referrer=searchResults

Answer:

The rms current is 0.3112 A.

Explanation:

Given that,

Suppose, The capacitance is 170 μF and the inductance is 2.94 mH. The resistance in the top branch is 278 Ohms, and in the bottom branch is 151 Ohms. The potential of the power supply is 47 V .

We know that,

When the frequency is very large then the capacitance can be treated as a short circuit and inductance as open circuit.

So,

We need to calculate the rms current

Using formula of current

[tex]I=\dfrac{V}{R}[/tex]

Where, V = voltage

R = resistance

Put the value into the formula

[tex]I=\dfrac{47}{151}[/tex]

[tex]I= 0.3112 \ A[/tex]

Hence, The rms current is 0.3112 A.

Answer:

None of the above

Explanation:

The formula of the magnetic field of a point next to a wire with current is:

B = 2×10^(-7) × ( I /d)

I is the intensity of the current.

d is the distance between the wire and the point.

● B = 2*10^(-7) × (20/5) = 8 ×10^(-7) T

Answer:

1.125×10⁻⁹ J

Explanation:

Applying,

E = 1/2CV²................... Equation 1

Where E = Energy stored in the capacitor, C = capacitance of the capacitor, V = Voltage of the battery.

Given; C = 1.0 nF,  = 1.0×10⁻⁹ F, V = 1.5 V

Substitute into equation 1

E = 1/2(1.0×10⁻⁹×1.5²)

E = 1.125×10⁻⁹ J

Hence the energy stored by the capacitor is 1.125×10⁻⁹ J

Answer:

The final temperature of both objects is 400 K

Explanation:

The quantity of heat transferred per unit mass is given by;

Q = cΔT

where;

c is the specific heat capacity

ΔT is the change in temperature

The heat transferred by the  object A per unit mass is given by;

Q(A) = caΔT

where;

ca is the specific heat capacity of object A

The heat transferred by the  object B per unit mass is given by;

Q(B) = cbΔT

where;

cb is the specific heat capacity of object B

The heat lost by object B is equal to heat gained by object A

Q(A) = -Q(B)

But heat capacity of object B is twice that of object A

The final temperature of the two objects is given by

[tex]T_2 = \frac{C_aT_a + C_bT_b}{C_a + C_b}[/tex]

But heat capacity of object B is twice that of object A

[tex]T_2 = \frac{C_aT_a + C_bT_b}{C_a + C_b} \\\\T_2 = \frac{C_aT_a + 2C_aT_b}{C_a + 2C_a}\\\\T_2 = \frac{c_a(T_a + 2T_b)}{3C_a} \\\\T_2 = \frac{T_a + 2T_b}{3}\\\\T_2 = \frac{300 + (2*450)}{3}\\\\T_2 = 400 \ K[/tex]

Therefore, the final temperature of both objects is 400 K.

Answer:

c. 70 Ω

Explanation:

The R and R resistors are in parallel.  The 2R and 2R resistors are in parallel.  The 4R and 4R resistors are in parallel.  Each parallel combination is in series with each other.  Therefore, the equivalent resistance is:

Req = 1/(1/R + 1/R) + 1/(1/2R + 1/2R) + 1/(1/4R + 1/4R)

Req = R/2 + 2R/2 + 4R/2

Req = 3.5R

Req = 70Ω

Answer:

In an adiabatic process we have

pV γ = const..

This explains that the pressure is a function of volume, p ( V ) ,

So can be written as:

p ( V ) × V γ = p 0 V γ 0 ,

or p ( V ) = p 0 V 0 / V γ

= p 0 V 0 / V ^(7 / 5)

Complete question is;

A circuit consists of four 100-W lamps connected in parallel across a 230-V supply. Inadvertently, a voltmeter has been connected in series with the lamps. The resistance of the voltmeter is 1500 Ω and that of the lamps under the conditions stated is six times their value then burning normally. What will be the reading of the voltmeter?

Answer:

150.42 V

Explanation:

We are told that the circuit consists of four 100W lamps.

We know that Power is given by the equation;

P = V²/R

Thus;

R = V²/P

Now, we are told that the four lamps are connected in parallel across a 230V supply.

Thus, V = 230 V

So resistance, R = 230²/100

R = 529 Ω

We are told that the resistance of the lamps under the conditions stated is six times their value when burning normally.

Thus, total resistance of each lamp under the conditions = 529 × 6 = 3174 Ω

So, since they are connected in parallel, equivalent resistance for each lamp = 3174/4 = 793.5 Ω

Now, since this resistance is connected in series with the voltmeter resistance of 1500 Ω

Therefore, total circuit resistance = 1500 + 793.5 = 2293.5 Ω

Thus;

circuit current = 230/2293.5 = 0.100283 A

Now, according to Ohm’s law, voltage drop across the voltmeter = 1500 × 0.100283 ≈ 150.42V

CHECK THE COMPLETE QUESTION BELOW

A circuit consists of four 100-W lamps connected in parallel across a 230-V supply. Inadvertently, a voltmeter has been connected in series with the lamps. The resistance of the voltmeter is 1500 Ω and that of the lamps under the conditions stated is six times their value then burning normally. What will be the reading of the voltmeter?

Answer:

the reading of the voltmeter=150.4V

Explanation:

We can determine the wattage of a lamp using below expression:

: W = I² R....................eqn(1)

But fro ohms law V=IR

then I= V/R

If we substitute I into equation (1)

We have W= V²/R

But W= 100W

V= 230V

Then

W=220²/R

100 = 2302/R

R = 529 Ω

We can as well calculate the Resistance of each lamp under given condition that they are sixtimes their value when burning normally.

R = 6 × 529 = 3174 Ω

We can also calculate quivalent resistance of the abovefour lamps connected in parallel then

R = 3174/4

= 793.5 Ω

total circuit resistance can be calculated since we know that resistance is connected to voltmeter of 1500 Ω resistance in series arrangement

Then

total circuit resistance = 1500 + 793.5

= 2293.5 Ω

Then from ohms law again

I= V/R

circuit current = 230/2293.5 A

The reading of the voltage drop across the voltmeter

= 1500 × 230/2293.5

= 150.4V

Answer:

a. 0.342 kg-m² b. 2.0728 kg-m²

Explanation:

a. Since the skater is assumed to be a cylinder, the moment of inertia of a cylinder is I = 1/2MR² where M = mass of cylinder and r = radius of cylinder. Now, here, M = 56.5 kg and r = 0.11 m

I = 1/2MR²

= 1/2 × 56.5 kg × (0.11 m)²

= 0.342 kgm²

So the moment of inertia of the skater is

b. Let the moment of inertia of each arm be I'. So the moment of inertia of each arm relative to the axis through the center of mass is (since they are long rods)

I' = 1/12ml² + mh² where m = mass of arm = 0.05M, l = length of arm = 0.875 m and h = distance of center of mass of the arm from the center of mass of the cylindrical body = R/2 + l/2 = (R + l)/2 = (0.11 m + 0.875 m)/2 = 0.985 m/2 = 0.4925 m

I' = 1/12 × 0.05 × 56.5 kg × (0.875 m)² + 0.05 × 56.5 kg × (0.4925 m)²

= 0.1802 kg-m² + 0.6852 kg-m²

= 0.8654 kg-m²

The total moment of inertia from both arms is thus I'' = 2I' = 1.7308 kg-m².

So, the moment of inertia of the skater with the arms extended is thus I₀ = I + I'' = 0.342 kg-m² + 1.7308 kg-m² = 2.0728 kg-m²

a) The moment of inertia as the skater pulled his/her arm inward by assuming he/she is a cylinder is 0.3418kg-m².

b) If the body of the skater is assumed to be a cylinder of the same size, and the arms are rods extending straight out from his/her body being rotated at the ends, the moment of inertia is 1.7495kg-m².

Given the data in the question;

Mass of skater; [tex]M = 56.5kg[/tex]

a)

When the skater has his arms pulled inward by assuming they are cylinder of radius; [tex]R = 0.11 m[/tex]

Moment of inertia; [tex]I = \ ?[/tex]

From Parallel axis theorem; Moment of Inertia for a cylindrical body is expressed:

[tex]I = \frac{1}{2}MR^2[/tex]

Where M is the mass and R is the radius

We substitute our given values into the equation

[tex]I = \frac{1}{2}\ *\ 56.5kg\ *\ (0.11m)^2\\\\I = \frac{1}{2}\ *\ 56.5kg\ *\ 0.0121m^2\\\\I = 0.3418kg.m^2[/tex]

Therefore, the moment of inertia as the skater pulled his/her arm inward by assuming he/she is a cylinder is 0.3418kg-m²

b)

With the skater's arms extended by assuming that each arm is 5% of the mass of their body

Mass of each arm; [tex]M_a = \frac{5}{100} * M = \frac{5}{100} * 56.5kg = 2.825kg[/tex]

Remaining mass; [tex]M_b = M - 2M_a = 56.5kg - 2(2.825kg) = 50.85kg[/tex]

Assume the body is a cylinder of the same size and the arms are 0.875 m long rods extending straight out from their body being rotated at the ends.

Length of arm; [tex]L = 0.875 m[/tex]

From Parallel axis theorem; Moment of Inertia about vertical axis is expressed as:

[tex]I = \frac{1}{2}M_bR^2 + \frac{2}{3}M_aL^2[/tex]

We substitute in our values

[tex]I = \frac{1}{2}*50.85kg*(0.11m)^2 + \frac{2}{3}*2.825kg*(0.875m)^2\\\\I = [\frac{1}{2}*50.85kg * 0.0121m^2] + [\frac{2}{3}*2.825kg*0.765625m^2]\\\\I = 0.3076kg.m^2 + 1.4419kg.m^2\\\\I = 1.7495kg.m^2[/tex]

Therefore, if the body of the skater is assumed to be a cylinder of the same size, and the arms are rods extending straight out from his/her body being rotated at the ends, the moment of inertia is 1.7495kg-m².

Learn more: https://brainly.com/question/6897330

Answer:

Frequency

Explanation:

When waves travel from one medium to another, it is only the frequency of the wave that remains constant . when a wave is refracted at the boundary between two media, the wave will slow down and its wavelength decreases. The wave usually bends at the interface between the two media. The wavelength and speed of a wave may change at the boundary between two media but its frequency remains the same.

Hence the frequency of light is its only property that remains constant.

Answer:

a

   [tex]m = 0.169 \ kg[/tex]

b

  [tex]|v_{max} |= 0.5653 \ m/s[/tex]

Explanation:

From the question we are told that

    The  spring constant is  [tex]k = 14 \ N/m[/tex]

     The  maximum extension of the spring is  [tex]A = 6.0 \ cm = 0.06 \ m[/tex]

     The number of oscillation is  [tex]n = 30[/tex]

      The  time taken is  [tex]t = 20 \ s[/tex]

Generally the the angular speed of this oscillations is mathematically represented as

           [tex]w = \frac{2 \pi}{T}[/tex]

where T is the period which is mathematically represented as

     [tex]T = \frac{t}{n}[/tex]

substituting values

     [tex]T = \frac{20}{30 }[/tex]

     [tex]T = 0.667 \ s[/tex]

Thus  

       [tex]w = \frac{2 * 3.142 }{ 0.667}[/tex]

       [tex]w = 9.421 \ rad/s[/tex]

this angular speed can also be represented mathematically as

       [tex]w = \sqrt{\frac{k}{m} }[/tex]

=>   [tex]m =\frac{k }{w^2}[/tex]

substituting values

      [tex]m =\frac{ 15 }{(9.421)^2}[/tex]

      [tex]m = 0.169 \ kg[/tex]

In SHM (simple harmonic motion )the equation for velocity is  mathematically represented as

        [tex]v = - Awsin (wt)[/tex]

The  velocity is maximum when  [tex]wt = \(90^o) \ or \ 1.5708\ rad[/tex]

     [tex]v_{max} = - A* w[/tex]

=>   [tex]|v_{max} |= A* w[/tex]

=>    [tex]|v_{max} |= 0.06 * 9.421[/tex]

=>   [tex]|v_{max} |= 0.5653 \ m/s[/tex]

Answer:

They both have the same acceleration

Explanation:

Using Equations of Motion :

[tex]s = ut + \frac{1}{2} g {t}^{2} [/tex]

Height = 0 * 4 + 4.9 * 16

Height = 78.4 m

Answer:

Chemical changes are recognized when a substance changes its properties permanently and it cannot be the same substance as before.

Instead the physical changes implies that if you can return to the same substance through a reverse process.

Explanation:

A chemical change is, by example, a combustion, if a sheet of paper burns, its result is ashes, the ashes cannot go back to being a sheet of paper because its properties changed, heat energy was generated that changed matter permanently.

A physical change, by example, is that of freezing water, the water becomes ice, but this can easily become water again if the temperature is increased, its properties do not change and the chemistry of the substance does not change.

A chemical change takes place when a chemical reaction takes place, while when a matter changes forms but not the chemical identity then a physical change takes place.  

• A product or a new compound formation takes place from a chemical change as the rearrangement of atoms takes place to produce novel chemical bonds.  

• In a chemical change always a chemical reaction takes place.  

• Some of the chemical changes examples are souring milk, burning wood, digesting food, mixing acid and base, cooking food, etc.  

• In a physical change no new chemical species form.  

• The changing of the state of a pure substance between liquid, gas, or solid is a physical change as there is no change in the identity of the matter.  

• Some of the physical changes are melting of ice, tempering of steel, breaking a bottle, crumpling a sheet of aluminum foil, boiling water, and shredding paper.  

Thus, a new substance is formed during a chemical change, while a physical change does not give rise to a new substance.  

To know more about:

https://brainly.com/question/7279398

Explanation:

1 inch = 25.4 mm

1 foot = 12 inches

1 mile = 5260 feet

1 cm = 0.01 m or 10 mm

Now Sammy's height is 5 feet and 5.3 inches.

(a) We need to find Sammy's height in inches.

Since, 1 foot = 12 inches

5 feet = 5 × 12 inches = 60 inches

Now, 5 feet and 5.3 inches = 60 inches + 5.3 inches = 65.3 inches

Sammy's height is 65.3 inches.

(b) We need to find Sammy's height in feet.

Since, 1 foot = 12 inches

[tex]1\ \text{inch}=\dfrac{1}{12}\ \text{feet}[/tex]

So,

[tex]5.3\ \text{inch}=\dfrac{5.3}{12}\ \text{feet}=0.4416\ \text{feet}[/tex]

5 feet and 5.3 inches = 5 feet + 0.4416 feet = 5.44 feet

Sammy's height is 5.44 feet.

1. Which example best describes a restoring force?

B) the force applied to restore a spring to its original length

2. A spring is compressed, resulting in its displacement to the right. What happens to the spring when it is released?

C) The spring exerts a restoring force to the left and returns to its equilibrium position.

3. A 2-N force is applied to a spring, and there is displacement of 0.4 m. How much would the spring be displaced if a 5-N force was applied?

D) 1 m

4. Hooke’s law is described mathematically using the formula Fsp=−kx. Which statement is correct about the spring force, Fsp?

D)It is a vector quantity.

5. What happens to the displacement vector when the spring constant has a higher value and the applied force remains constant?

A) It decreases in magnatude.

Answer

1.07E22 Joules

Explanation;

We know that mass expands by a factor

=>>1/√[1-(v/c)²]

But v= 0.509c

So

1/√(1 - 0.509²)

=>>> 1/√(1 - 0.2591)

= >> 1/√(0.7409) = 1.16

But given that 121 tons is rest mass so 121- 1.16= 119.84 tons is kinetic energy

And we know that rest mass-energy equivalence is 9 x 10^19 joules per ton.

So Multiplying by 119.84

Kinetic energy will be 1.07x 10^22 joules

Answer:

Lighthouse 1 during the day will be warmer, lighthouse 2 during the night will be warmer.

Explanation:

As the paragraph stated land absorbs heat and heats up faster than water. So during the day the lighthouse farthest away from the water will be hotter. But then the converse is true also land losses heat faster than water at night. So the water retains the heat from the day better making the lighthouse by the water warmer at night.

The provided question is not correct as, there is more than one options are correct, however the explaining every correct option -

Answer:

The correct answer are - silver, copper and aluminium all three used as fuse material.

Explanation:

A safety device in any electric circuit of that prevents the electric system in case of short circuit by breaking the connection of electric system or circuit termed as the Fuse or fuse element. Normally the fuse are made up of wire or element of material that are low in melting point and high in resistance.

Zinc, lead, tin, silver, copper, aluminium, and alloy of tin and alloy are used as fuse element or material for their low melting point and high resistance these are easily breaks the electric path in case of short circuit.