the circuit in the drawing contains five identical resistors. the 45-v battery delivers 78 w of power to the circuit. what is the resistance r of each resistor?

Answers

Answer 1

Answer:

I got 26.0Ω

Explanation:

First, you'll need to calculate the current flowing through the circuit with the given values. I used this formula;

P = VI

Substitute the values:

78 = 45 × I

I = 78/45

∴ I = 1.73A (3sf)

Now that we have our current, we can finally calculate the resistance of one resistor. The formula I used is;

V = IR

45 = 1.73 × R

R = 45/1.73

∴ R = 26.0Ω

When there are multiple resistors in parallel, they all would have the same voltage. Hence, the voltage I used to calculate the resistance is 45V!

I hope this helps! Please let me know if I have any misconceptions or miscalculations as I'm still learning! Thank you and your welcome! :D

Answer 2

Each resistor in the circuit has a resistance of 6 ohms.

How to find the resistance r of each resistor?

In the given circuit, there are five identical resistors. Let's denote the resistance of each resistor as R. Since the resistors are identical, they all have the same resistance. Let's calculate the total resistance of the circuit.

When resistors are connected in parallel, the total resistance (Rp) can be calculated using the formula:

1/Rp = 1/R + 1/R + 1/R + 1/R + 1/R

Simplifying this equation, we get:

1/Rp = 5/R

Now, let's find the value of Rp. We know that power (P) can be calculated using the formula:

P = V²/ R

Given that the battery delivers 78 W of power to the circuit and the voltage (V) is 45 V, we can rearrange the formula to solve for R:

R = V²/ P

Substituting the given values, we get:

R = (45²) / 78 = 25.96 ohms

Since each resistor has the same resistance, we can conclude that each resistor in the circuit has a resistance of approximately 6 ohms.

Learn more about resistors

brainly.com/question/30672175

#SPJ11


Related Questions

Why do rowers typically have the same number of paddles on each side of the boat?
a) It provides balance and symmetry in rowing.
b) It allows for efficient distribution of power.
c) It helps maintain stability and control.
d) All of the above

Answers

Rowers typically have the same number of paddles on each side of the boat because it provides balance and symmetry in rowing. The correct option is (a) It provides balance and symmetry in rowing.

Balance and symmetry are key components of effective rowing. When all rowers use the same number of paddles on each side of the boat, they create an evenly distributed power source that helps keep the vessel stable and on course. To maintain the balance and symmetry of the boat while rowing, the number of paddles on each side must be the same.

As a result, all rowers need to be coordinated and work together to ensure that their oars are in sync with one another. They should all have the same posture, the same rhythm, and the same intensity of strokes to ensure that they are not working against one another and instead, are working together to power the boat as efficiently as possible.In conclusion, rowers typically have the same number of paddles on each side of the boat to provide balance and symmetry in rowing.

To know more about balance  visit:-

https://brainly.com/question/27154367

#SPJ11

Consider a vertical pipe through which humid air flows. The pipe is kept at 5 oC, which is cooler than
the air and, importantly, below the 8 oC dew point of the air. As a result, water condenses on the
inner walls to maintain a thin layer of liquid water. Though the water layer would eventually get
thick enough that it would fall due to gravity, you can neglect that here.
a. Draw a picture of the physical system, select the coordinate system that best describes the
transfer process, and state at least five reasonable assumptions of the mass-transfer aspects of
the process.
b. What is the simplified form of the general differential equation for mass transfer in terms of the
flux of water vapor, NA?
c. What is the simplified differential form of Fick’s flux equation for water vapor?
d. What is the simplified form of the general differential equation for mass transfer in terms of the
molar concentration of water vapor, cA?

Answers

Assumptions: Assumptions are an important part of the process of modeling since they allow you to focus on the essential physics of the problem.

Correct option is a. Picture of the physical system:

Below are some of the assumptions made for the given system:It can be assumed that the flow of air is laminar.

The concentration of water vapor in the gas stream does not change as a result of the transfer process. The temperature at any location in the system is uniform and constant. The air does not undergo any significant change in pressure.

The only mass transfer process that occurs is evaporation and condensation.

b. The simplified form of the general differential equation for mass transfer in terms of the flux of water vapor, NA is,

c) The simplified differential form of Fick’s flux equation for water vapor is given by

d) The simplified form of the general differential equation for mass transfer in terms of the molar concentration of water vapor, cA is given by [tex]$\frac{\partial \frac{N_{A}}{\rho_{g}}}{\partial t}[/tex]

=[tex]\frac{\partial}{\partial z}\left[\frac{D_{AB}}{\rho_{g}}\frac{\partial c_{A}}{\partial z}\right]$[/tex]

To know more about laminar flow, visit:

https://brainly.com/question/23008935

#SPJ11

Q3: Please show your complete solution and explanation. Thank
you!
3. One mole of an ideal gas is expanded isothermally to twice its initial volume a) calculate AS. b) What would be the value of AS if five moles of an ideal gas were doubled in volume isothermally?

Answers

One mole of an ideal gas is expanded isothermally to twice its initial volume a) ΔS is equal to  (8.314 J/K) ln(2). b)  The value of ΔS would be approximately 41.57 ln(2) J/K if five moles of an ideal gas were doubled in volume isothermally.

a) The change in entropy (ΔS) for the isothermal expansion of one mole of an ideal gas, we can use the equation:

ΔS = nR ln(Vf/Vi)

Where:

ΔS is the change in entropy,

n is the number of moles of gas (1 mole in this case),

R is the ideal gas constant (8.314 J/(mol·K)),

Vf is the final volume,

Vi is the initial volume.

Since the volume is expanded to twice its initial value, we have Vf = 2Vi.

Plugging these values into the equation, we get:

ΔS = (1 mole)(8.314 J/(mol·K)) ln(2Vi/Vi)

      = (8.314 J/K) ln(2)

b) If five moles of an ideal gas were doubled in volume isothermally, we can calculate the change in entropy (ΔS) using the same equation as above, but with n = 5:

ΔS = (5 moles)(8.314 J/(mol·K)) ln(2Vi/Vi)

      = (41.57 J/K) ln(2)

Therefore, the value of ΔS would be approximately 41.57 ln(2) J/K for five moles of an ideal gas when doubled in volume isothermally.

To learn more about isothermally refer here:

https://brainly.com/question/31828834#

#SPJ11

determine the magnitude of the velocity of the ball when t = 1.3 s .

Answers

[tex]6t^{1/\\2}[/tex] radian is the angular velocity of the ball when t = 1.3 s. The change in angular position in a given time by a rotating body is called angular velocity.

Given information,

Time = 1.3 seconds

The radial position of the ball = 0.1 t³

Now,

The radial velocity of the ball,

dr/dt = d(0.1 t³)/dt

r' = 0.1 ×3t²

= 0.3t²

dr'/dt = 0.3 dt² /t = 0.3 × 2t

r" = 0.6t

At t=0.3sec.

r' = 0.3 × (1.3)² = 0.507 m/s²

r" = 0.6 × 1.3 = 0.78 m/s²

r = 0.1 × t³ = 0.21697 m/s²

The angular position of the ball (θ) = 4t³/² rad

The angular velocity = dθ/dt

= 4 d/dt t^3/2

=4 × 3/2 t^1/2

= [tex]6t^{1/2}[/tex] radian.

Therefore, the velocity of the ball when t = 1.3s is [tex]6t^{1/2}[/tex] radian.

Learn more about velocity, here:

https://brainly.com/question/30559316

#SPJ4

Your question is incomplete, most probably the full question is this:

determine the magnitude of the velocity of the ball when t = 1.3 s .

Our Sun, a type G star, has a surface temperature of 5800 K. We know, therefore, that it is cooler than a type O star and hotter than a type M star Othersportta coos tracking id: ST-630-45-4466-38345. In accordance with Expert TA's Terms of Service copying this information t 50% Part (a) How many times hotter than our Sun is the hottest type O star, which has a surface temperature of about 40,000 K? Number of times hotter sin() cos() tan() asin() acos() B12 SOAL atan() acotan() sinh() cotanh() tanh) Degrees O Radians cotan() cosh() (1) 7 4 1 Hint 8 9 5 6 2 3 + 0 VO CONCE . CLEAK Submit I give up! Hints: 0% deduction per hint. Hints remaining: 1 Feedback: 1% deduction per feedback. 50% Part (b) How many times hotter is our Sun than the coolest type M star, which has a surface temperature of 2400 K?

Answers

(a) The hottest type O star is approximately 6.90 times hotter than our Sun.

(b) Our Sun is approximately 2.42 times hotter than the coolest type M star.

How many times hotter than our Sun is the hottest type O star with a surface temperature of about 40,000 K, and how many times hotter is our Sun than the coolest type M star with a surface temperature of 2400 K?

Part (a) To determine how many times hotter the hottest type O star is compared to our Sun, we can calculate the temperature ratio as follows:

Temperature ratio = Temperature of the type O star / Temperature of our Sun

                = 40,000 K / 5,800 K

                ≈ 6.90

Therefore, the hottest type O star is approximately 6.90 times hotter than our Sun.

Part (b) To determine how many times hotter our Sun is compared to the coolest type M star, we can calculate the temperature ratio as follows:

Temperature ratio = Temperature of our Sun / Temperature of the type M star

                = 5,800 K / 2,400 K

                ≈ 2.42

Therefore, our Sun is approximately 2.42 times hotter than the coolest type M star.

Learn more about hottest type

brainly.com/question/30049280

#SPJ11

_______ increases when air faces greater resistance against an object with a larger surface area. (4 letters)

Answers

The term that increases when air faces greater resistance against an object with a larger surface area is drag.

The drag force is created when a solid object moves through a fluid (liquid or gas), such as air, and experiences resistance to its motion.Drag can be affected by various factors, including the object's shape and surface area. In general, objects with larger surface areas will experience more drag than those with smaller surface areas because they create more friction with the surrounding fluid. For example, a flat, wide object like a barn door will experience more drag than a narrow object like a pencil because it has a larger surface area. Similarly, a parachute will experience a large amount of drag because of its large surface area, which creates a significant amount of friction with the air molecules around it.In order to minimize drag and increase efficiency, engineers and designers often try to create streamlined objects with minimal surface area. This can be seen in the design of cars, airplanes, and even swimsuits used by competitive swimmers. By minimizing drag, these objects are able to move more quickly and with less effort through their respective fluids.

for such more questions on  resistance

https://brainly.com/question/28135236

#SPJ8

for the following exothermic reaction at equilibrium: h2o (g) co (g) co2(g) h2(g) decide if each of the following changes will increase the value of k (t = temperature)

Answers

For the given exothermic reaction at equilibrium:H2O(g) + CO(g) ⇌ CO2(g) + H2(g)Changes in pressure, temperature, or concentration may shift the equilibrium position, but they do not affect the value of Kc, which is constant for a given reaction at a given temperature. Hence, Kc is independent of any changes in the concentrations of reactants and products, as well as changes in the reaction conditions, as long as the temperature remains constant.To assess the effect of each change on the equilibrium constant, we must use Le Chatelier's principle to predict which direction the reaction will proceed to reestablish equilibrium. The shift in the equilibrium can cause Kc to vary when the system comes to equilibrium at the new conditions.A change in pressure will influence the equilibrium position of a gaseous reaction since gases are extremely responsive to pressure. If the pressure is increased on one side of an equilibrium reaction, the reaction will shift to the opposite side of the equation to balance the pressure. The equilibrium constant (Kc) will not change, but the pressure will influence the mole fractions of reactants and products, which will have an impact on the direction of the equilibrium shift and the rate at which it occurs. Increasing the pressure by decreasing the volume of the container in which the equilibrium reaction is occurring will result in a shift towards the side of the equation with fewer gas molecules, and the system will attempt to balance the pressure. Therefore, the reaction will shift to the left, resulting in a decrease in Kc. Since the reverse reaction, which is exothermic, is favored at lower temperatures, an increase in the value of Kc is not expected as the temperature is lowered. This means that the first option will not result in an increase in Kc. If the volume is increased, the reaction will shift towards the side with more gas molecules to compensate, resulting in an increase in Kc. This means that the second option will lead to an increase in Kc.

To know more about Le Chatelier's principle visit

https://brainly.com/question/29009512

#SPJ11

Exothermic reactions at equilibrium: In an exothermic reaction, the energy is released to the surrounding as heat. An exothermic reaction always has a negative sign for ΔH. An exothermic reaction at equilibrium means that the reactants and products are still reacting, but at the same rate. The reaction quotient, Qc, is equal to the equilibrium constant, Kc. The given exothermic reaction is: H2O (g) + CO (g) ⇌ CO2(g) + H2(g)The balanced equation is as follows: H2O(g) + CO(g) ⇌ CO2(g) + H2(g)Decide if each of the following changes will increase the value of K (T = temperature): Increasing the temperature The given reaction is exothermic.

An increase in temperature will favor the backward reaction and oppose the forward reaction to attain equilibrium. According to Le Chatelier’s principle, if stress is applied to an equilibrium system, it will react to counteract the effect of that stress. Hence, an increase in temperature will cause the equilibrium to shift towards the reactants, as it is an endothermic process. Therefore, the value of Kc will decrease. Decreasing the pressure CO and H2 are gaseous reactants, whereas CO2 and H2O are gaseous products. A decrease in pressure will favor the side of the reaction with more number of gaseous molecules to oppose the change. Therefore, the equilibrium will shift towards the reactants to balance the pressure. Hence, the value of Kc will increase. Adding a catalyst A catalyst is a substance that increases the rate of a chemical reaction by providing an alternative pathway for the reaction with a lower activation energy. A catalyst does not affect the equilibrium position of the reaction, but it helps in achieving the equilibrium state at a faster rate. Hence, adding a catalyst will not affect the value of Kc, as it is independent of the rate of the reaction. The following changes will increase the value of K (T = temperature): Decreasing the temperature Increasing the pressure Therefore, the decrease in temperature and increase in pressure will increase the value of Kc.

To get more information about Le Chatelier’s principle visit:

https://brainly.com/question/29009512

#SPJ11

Two parallel plates are held 10cm from one another. The potential difference between the plates is held at 100V. In this problem, ignore edge effects. (a) Find the electric field between the plates. (

Answers

The electric field between the plates is 1,000 V/m.

The electric field between parallel plates is given by the equation E = V/d, where E is the electric field, V is the potential difference, and d is the distance between the plates.

In this problem, the potential difference between the plates is 100V, and the distance between the plates is 10cm, which is equal to 0.1m.

Substituting these values into the equation, we have E = 100V / 0.1m = 1,000 V/m.

The electric field represents the force experienced by a unit positive charge placed between the plates. In this case, the electric field is constant and uniform between the plates since edge effects are ignored.

The electric field lines are directed from the positive plate to the negative plate.

The magnitude of the electric field is directly proportional to the potential difference between the plates and inversely proportional to the distance between the plates.

Therefore, increasing the potential difference or decreasing the distance between the plates will result in a stronger electric field.

To know more about "Electric field" refer here:

https://brainly.com/question/12118166#

#SPJ11

An electric field component of a polarized ray is expressed
as:
Ez=(8 V/m)cos⁡[(2×10^6 m^(-1) )x+ ωt]
(a) Write down the shape of the magnetic field component of this
ray, including the value of �

Answers

The electric field component of a polarized ray is expressed as the equation E = E_0 sinθ.

When a ray is polarized, it means that it vibrates in only one direction. In other words, the electric field of the light wave moves in only one direction, perpendicular to the direction the wave is moving.

This electric field component of a polarized ray is given by the equation E = E_0 sinθ, where E is the magnitude of the electric field vector at any point along the path of the wave, E_0 is the maximum value of the electric field vector, and θ is the angle between the direction of polarization and the direction of the electric field.

Thus, the value of θ ranges from 0 to 180 degrees. The electric field vector oscillates back and forth as the wave propagates, with the magnitude of the vector being maximum when the wave is at its peak and zero when the wave is at its trough.

This equation is an important tool in describing the properties of polarized light waves in various optical systems.

Polarized lenses protect your eyes from the sun's UVA and UVB rays while also reducing glare for improved contrast and clarity. Bring the world around you to life with our collection of iconic sunglasses for men and fashionable sunglasses for women with Polarized lenses.

Know more about polarized ray, here:

https://brainly.com/question/32242228

#SPJ11

A voltaic cell consists of an Mn/Mn2+ half-cell and a Caicd2+ half-cell. The standard reduction potential for Mn2+ is -1.18V and for Cd2+ is -0.40 V. Calculate Ecell at 25 °C when the concentration of [Cd2+] = 8.84 x 10-0 M and [Mn2+1=9.57 x 10-5 M. (value + 0.02) Selected Answer: [None Given] Correct Answer: 0.93 +0.02

Answers

The value of E-cell at 25 °C when the concentration of [Cd2+] = 8.84 × 10⁻⁰ M and [Mn2+1=9.57 × 10⁻⁵ M is 0.93 + 0.02 V.

The chemical equation for the reaction of a voltaic cell made up of a Mn/Mn2+ half-cell and a Cd/Cd2+ half-cell is;2Mn2+ (aq) + Cd(s) → Cd2+ (aq) + 2Mn3+ (aq) (Overall cell reaction) E°cell = E°right - E°left= (-0.40) - (-1.18) = 0.78 V (The positive value indicates that the reaction is spontaneous)From the Nernst equation, Ecell = E°cell -  (RT/nF) * ln Q

where; R = gas constant = 8.31 J/mol. KT = temperature in kelvin = 25 + 273 = 298Kn = number of moles of electrons transferred = 2F = Faraday's constant = 96500 C/mol, Q = reaction quotient = [Cd2+]/[Mn2+}²= (8.84 × 10⁻⁰) / (9.57 × 10⁻⁵)²= 97.3Ecell = 0.78 - [(8.31 × 298) / (2 × 96500)] * ln 97.3Ecell = 0.93 + 0.02 V (rounded off to 2 decimal places).

To know more about voltaic cell, visit:

https://brainly.com/question/29186551

#SPJ11

determine the time it takes to achieve an angular velocity of ω = 198 rad/s . when t = 0, θ = 1 rad .

Answers

To determine the time it takes to achieve an angular velocity of ω = 198 rad/s, given that at t = 0, θ = 1 rad, we can use the equation of angular motion.

The equation that relates angular displacement, angular velocity, and time is θ = ω₀t + (1/2)αt², where θ is the angular displacement, ω₀ is the initial angular velocity, t is the time, α is the angular acceleration, and t² denotes t squared.

In this case, we are given that ω₀ = 0 since the initial angular velocity is not provided. Assuming there is no angular acceleration mentioned, we can simplify the equation to θ = (1/2)αt².

Rearranging the equation to solve for time, we have t = sqrt((2θ) / α).

Substituting the given values, θ = 1 rad and ω = 198 rad/s, we need additional information on the angular acceleration (α) to calculate the time it takes to achieve the given angular velocity.

To know more about  angular acceleration, click here:

https://brainly.com/question/30237820

#SPJ11

the lines 593-620 that show the reaction to beowulf's return to herot:

Answers

The lines 593-620 of Beowulf show the reaction of people in Herot upon Beowulf's return.  The poet uses vivid imagery and figurative language to highlight the emotions of the people in Herot and to convey the significance of the moment.

In Beowulf, the lines 593-620 illustrate the crowd's reaction when Beowulf returned to Herot. Hrothgar delivers a touching speech and declares Beowulf the greatest hero of all time. Hrothgar is happy to see Beowulf alive and well, and he praises Beowulf for his bravery, claiming that he is now a noble man.After the speech, everyone in the hall lifts their cups, and they all drink to Beowulf's health. Everyone in Herot is overjoyed by Beowulf's success, and they celebrate the moment with joy and happiness. The poet emphasizes the significance of social drinking in medieval society by using the phrase "drank with delight," which highlights the importance of communal bonding in society. It also highlights the theme of fellowship and loyalty, which is essential in medieval society.

Beowulf is the oldest surviving epic poem in English literature and provides a valuable insight into Anglo-Saxon society. The lines 593-620 in Beowulf describe the reaction of the people in Herot upon Beowulf's return. Hrothgar, the king of the Danes, delivers a moving speech in which he praises Beowulf for his bravery and declares him the greatest hero of all time. Hrothgar expresses his delight in seeing Beowulf alive and well, and he elevates Beowulf's status to that of a nobleman in society.In the hall, everyone is filled with happiness and joy, and they all raise their cups to drink to Beowulf's health. This scene also illustrates the importance of the lord and vassal relationship in Anglo-Saxon society. The people in Herot recognize Beowulf as their lord and pledge their loyalty to him, which is a significant aspect of the culture.The lines 593-620 in Beowulf are significant in understanding the social and cultural norms of Anglo-Saxon society. The scene describes the reaction of people in Herot upon Beowulf's return and illustrates the importance of communal bonding, fellowship, and loyalty in medieval society.

To know more about imagery visit :-

https://brainly.com/question/32354003

#SPJ11

the following appear on a physician's intake form. identify the level of measurement: (a) happiness on a scale of 0 to 10 (b) family history of illness (c) age (d) temperature

Answers

(a) The level of measurement for "happiness on a scale of 0 to 10" is an interval.

The happiness scale from 0 to 10 represents an interval measurement. The scale has equal intervals between the numbers, but it does not have a true zero point. The absence of happiness (0) does not indicate the complete absence of the attribute being measured. Therefore, it is an interval level of measurement.

(b) The level of measurement for "family history of illness" is nominal.

Family history of illness is a qualitative variable that represents categories or groups. It does not have a numerical order or magnitude. It is simply a classification of whether or not there is a family history of illness. Hence, it is a nominal level of measurement.

(c) The level of measurement for "age" is a ratio.

Age is a quantitative variable that has a meaningful zero point and a numerical order. Ratios between values are also meaningful. For example, someone who is 20 years old is half the age of someone who is 40 years old. Age satisfies all the properties of a ratio level of measurement.

(d) The level of measurement for "temperature" is an interval.

Temperature is a quantitative variable that can be measured on a scale such as Celsius or Fahrenheit. While temperature has equal intervals between the values, it does not have a true zero point (absolute absence of temperature). Therefore, it is an interval level of measurement.

To learn more about magnitude click here

https://brainly.com/question/29766788

#SPJ11

the force per meter between the two wires of a jumper cable being utilized to start a stalled van is 0.215 n/m.

Answers

This force per meter refers to the force experienced between two parallel wires carrying electric current.

When electric current flows through the wires, a magnetic field is generated around each wire. These magnetic fields interact with each other, resulting in a force between the wires.In the context of a jumper cable being used to start a stalled van, the force per meter indicates the force exerted between the positive and negative terminals of the jumper cable. This force is responsible for delivering electrical energy from the functioning vehicle's battery to the stalled van's battery to start the engine.

To know more about energy visit :

https://brainly.com/question/1932868

#SPJ11

what outcomes are in the event e, that the number of batteries examined is an even number?

Answers

The set of outcomes that is included in the event E, that the number of batteries examined is an even number, are as follows: {0, 2, 4, 6, 8, 10}.An event refers to a subset of the entire sample space of a random experiment that constitutes the collection of all possible outcomes. In this case, n(E) = 6 and n(S) = 11. Therefore, P(E) = 6 / 11

The event E indicates that the number of batteries examined is an even number. Therefore, only even numbers that are less than or equal to ten and greater than or equal to zero are a part of the event E, which includes 0, 2, 4, 6, 8, and 10. The sample space of this random experiment is the set of all possible outcomes.

If we assume that a total of 10 batteries are tested, the sample space is {0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10}.

So, the event E is a proper subset of the sample space, and the probability of E can be computed as:

P(E) = n(E) / n(S)

where n(E) is the number of outcomes in E, and n(S) is the number of outcomes in the sample space.

In this case, n(E) = 6 and n(S) = 11.

to know more about probability visit:

https://brainly.com/question/32117953

#SPJ11

what is the highest order dark fringe, , that is found in the diffraction pattern for light that has a wavelength of 629 nm and is incident on a single slit that is 1480 nm wide?

Answers

The highest order dark fringe, n is approximately equal to 2 for light that has a wavelength of 629 nm and is incident on a single slit that is 1480 nm wide.

The highest order dark fringe, n can be determined using the equation:

n λ = a sin θ

where,λ = 629 nma = 1480 nm

Given data:

wavelength (λ) = 629 nmsingle slit width (a) = 1480 nm

The highest order dark fringe, n can be determined using the equation:n λ = a sin θThe first dark fringe corresponds to n = 1, second dark fringe corresponds to n = 2, and so on.

For the highest order dark fringe, we need to find the largest value of n which gives a valid value of

sin θ.n λ = a sin θ ⇒ sin θ = (n λ) / a

For the highest order dark fringe, sin θ = 1 which gives:

n λ = a sin θ⇒ n λ = a⇒ n = a / λ

We have,a = 1480 nmλ = 629 nm

Substituting the values in the equation, we get:

n = a / λ= 1480 nm / 629 nm= 2.35 or 2 (approx)Therefore, the highest order dark fringe, n is approximately equal to 2

The highest order dark fringe, n is approximately equal to 2 for light that has a wavelength of 629 nm and is incident on a single slit that is 1480 nm wide.

To know more about dark fringe, visit:

https://brainly.com/question/31576174

#SPJ11

(20%) (a) (4%) Explain the coherence of wave and state its importance for interference. (b) (4 %) How to improve the interference result if you use a white-light bulb as the light source in Young's double slit experiment? (c) (4%) Explain why the degree of coherence of a laser is better than a light bulb. (d) (4%) A thin film of ZnS (n=2.37) is used to coat a camera lens (ng-1.53) so that it is antireflecting at a wavelength of 550 nm under normal incidence. Find the minimum thickness of the thin film. (e) (4%) A thin film of MgF2 (n= 1.38) is used to coat a camera lens (ng-1.53) so that it is antireflecting at a wavelength of 580 nm under normal incidence. What wavelength is minimally reflected when the light is incident instead at 45⁰?

Answers

A wave's ability to produce stationary interference is known as coherence.

Thus, Coherence is explained through several different ideas. Although these phenomena are uncommon in reality, they provide a basic grasp of waves. It has developed into a crucial idea in quantum physics and wave.

Thus, The term "coherence" refers to the characteristics of the correlation between the physical parameters of a single wave, a group of waves, or a wave packet.

For example, two parallel slits that are illuminated by a single laser beam can be categorized as two coherent sources. The photons of coherent light are in perfect time with one another. The phase shift for the light beam happens simultaneously.

Thus, A wave's ability to produce stationary interference is known as coherence.

Learn more about Wave, refer to the link:

https://brainly.com/question/3639648

#SPJ4

Calculate the work (kJ) done during a reaction in which the internal volume expands from 19 L to 48 L againts an outside pressure of 2.5 atm. W=-PdeltaV and atm.L= 101.235J
A) -7.3 kJ
B) 17 kJ
C) 7.3 kJ
D) -17 kJ
E) 0 kJ; No work is done

Answers

The work done during the reaction is approximately -7.3 kJ.

Hence, the correct option is A.

To calculate the work done during the reaction, we can use the formula:

W = -P * ΔV

Where:

W is the work done (in joules),

P is the external pressure (in atmospheres),

ΔV is the change in volume (in liters).

Given:

ΔV = 48 L - 19 L = 29 L

P = 2.5 atm

Substituting the values into the formula:

W = -2.5 atm * 29 L

Since 1 atm·L = 101.235 J, we can convert the units

W = -2.5 atm * 29 L * 101.235 J/(atmL)

W = -7365.08375 J

To convert the result to kilojoules, we divide by 1000:

W = -7.3 kJ

Therefore, the work done during the reaction is approximately -7.3 kJ. Hence, the correct option is A.

To know more about work done here

https://brainly.com/question/17032152

#SPJ4

The fundamental frequency of a pipe that is open at both ends is 594 Hz .
How long is this pipe?
If one end is now closed, find the wavelength of the newfundamental.
If one end is now closed, find the frequency of the newfundamental.

Answers

When one end is closed, the new wavelength is 1.154 m and the new fundamental frequency is 297 Hz.

The fundamental frequency of a pipe that is open at both ends is 594 Hz. In order to calculate the length of this pipe, we will use the formula v = fλ where v is the speed of sound, f is the frequency and λ is the wavelength.

The speed of sound in air is approximately 343 m/s.

We will therefore have: 594 = (343/λ)λ = (343/594)m = 0.577m or 57.7cm.

If one end of the pipe is now closed, it will act as a closed-end resonator which means that the wavelength will now be twice the length of the pipe.

Therefore, the new wavelength will be 2(0.577) = 1.154 m or 115.4 cm.

Using the formula v = fλ and substituting the new wavelength and speed of sound, we have 343 = f(1.154) which gives us the new fundamental frequency f as:

f = 297 Hz.

Thus, the length of the pipe that is open at both ends is 57.7 cm. When one end is closed, the new wavelength is 1.154 m and the new fundamental frequency is 297 Hz.

Learn more about fundamental frequency here:

https://brainly.com/question/31314205

#SPJ11

How much work does the electric field do in moving a -6.4x10-6 charge from ground to a point whose potential is 92 V higher?

Answers

The work done by the electric field in moving a -6.4x10^-6 charge from ground to a point 92 V higher is -5.888x10^-4 J.

The work done by an electric field in moving a charge can be calculated using the formula:

Work = q * ΔV

Where:

Work is the work done (in joules)

q is the charge (in coulombs)

ΔV is the change in potential (in volts)

q = -6.4x10^-6 C

ΔV = 92 V

Substituting these values into the formula, we get:

Work = (-6.4x10^-6 C) * (92 V)

= -5.888x10^-4 J

The work done by the electric field in moving a -6.4x10^-6 charge from ground to a point whose potential is 92 V higher is -5.888x10^-4 J. The negative sign indicates that the electric field does work against the motion of the charge, as the charge is moving to a higher potential.

To know more about Work, visit

brainly.com/question/25573309

#SPJ11

A box with a mass of 25 kg rests on a horizontal surface. The coefficient of static friction between the box and the surface is 0.20. What horizontal force must be applied to the box for it to start s

Answers

To start the box sliding along the surface in the positive x direction, a horizontal force greater than 49 N in the positive x direction must be applied.

The maximum static friction force can be calculated using the equation:

f_static_max = μ_static * N

where μ_static is the coefficient of static friction and N is the normal force acting on the box. In this case, since the box is on a horizontal surface, the normal force is equal to the weight of the box:

N = m * g

Substituting the given values:

N = 25 kg * 9.8 m/s² = 245 N

Now, we can determine the maximum static friction force:

f_static_max = 0.20 * 245 N = 49 N

This is the maximum force that can be exerted before the box starts sliding. Therefore, to overcome the static friction and initiate sliding in the positive x direction, a horizontal force greater than 49 N in the positive x direction must be applied. The exact value of the force will depend on the magnitude of the static friction and the force applied.

To know more about static friction refer here:

https://brainly.com/question/30886698#

#SPJ11

Complete Question:

A box with a mass of 25 kg rests on a horizontal surface. The coefficient of static friction between the box and the surface is 0.20. What horizontal force must be applied to the box for it to start sliding along the surface in the positive x direction? Use g = 9.8 m/s². O A horizontal force greater than 49 N in the positive x direction. O A horizontal force equal to 49 N in the positive x direction. O A horizontal force less than 49 N in the positive x direction. O A horizontal force that is either equal to or greater than 49 N in the positive x direction. O None of the other answers

5. In order to free electrons from nickel whose work function is 5.22 eV, what threshold frequency of light is needed? [K3]

Answers

In order to free electrons from nickel whose work function is 5.22 eV, the threshold frequency of light needed to free electrons from nickel is approximately 1.26 × [tex]10^1^5[/tex] Hz.

To calculate the threshold frequency of light needed to free electrons from nickel, we can use the equation:

E = hf

Where:

E is the energy required to free an electron (also known as the work function),

h is Planck's constant (6.626 × [tex]10^-^3^4[/tex] J·s),

f is the frequency of the light.

First, we need to convert the work function from electron volts (eV) to joules (J). Since 1 eV is equal to 1.602 ×[tex]10^-^1^9[/tex] J, the work function can be calculated as follows:

Work function (ϕ) = 5.22 eV * (1.602 × [tex]10^-^1^9[/tex] J/eV) ≈ 8.35 × [tex]10^-^1^9[/tex]J

Now, we can rearrange the equation to solve for the threshold frequency (f):

f = E / h

Substituting the values:

f = (8.35 ×[tex]10^-^1^9[/tex] J) / (6.626 × [tex]10^-^3^4[/tex] J·s) ≈ 1.26 × [tex]10^1^5[/tex] Hz

It's important to note that this calculation assumes a simplified model and neglects factors such as the band structure of the material and the presence of an electric field. In reality, the process of freeing electrons from a material surface involves a more complex interaction between light and matter, but this simplified approach provides an estimate for the threshold frequency required.

For more such information on: frequency

https://brainly.com/question/254161

#SPJ8

how deep is the shipwreck if echoes were detected 0.36 s after the sound waves were emitted?

Answers

If echoes were detected 0.36 s after the sound waves were emitted, the depth of the shipwreck is 65.52 meters. This can be calculated using the formula:distance = speed × timeWhere speed is the speed of sound in water, which is approximately 1481 meters per second.

The time is 0.36 seconds, as given in the problem.Therefore:

distance = speed × time

distance = 1481 × 0.36

distance = 532.56 meters

However, this distance is the total distance traveled by the sound wave, which includes both the distance from the ship to the bottom and the distance from the bottom to the surface. Since the sound wave travels twice this distance (down to the bottom and back up to the surface), we need to divide by 2 to find the depth of the shipwreck. So, the depth of the shipwreck is:

depth = distance / 2

depth = 532.56 / 2

depth = 265.28 meters

This means that the shipwreck is 265.28 meters deep.

For more information on shipwreck visit:

brainly.com/question/30244941

#SPJ11

Two external forces are applied to a particle: F1→=11 N i^+-5 N
j^ and F2→=18 N i^+-2.5 N j^.
A) Find the force F3→ that will keep the particle in
equilibrium.
Enter the x and y components separ

Answers

The force F3→ that will keep the particle in equilibrium is: F3→ = -29 N i^ + 7.5 N j^.

By summing the forces in the x and y directions and taking the negative of their sum, we can determine the force F3→ that will balance the applied forces and keep the particle in equilibrium.

To keep the particle in equilibrium, the net force acting on it must be zero. This means that the sum of the forces in the x-direction and the sum of the forces in the y-direction must both be zero.

F1→ = 11 N i^ - 5 N j^

F2→ = 18 N i^ - 2.5 N j^

To find the force F3→ that will keep the particle in equilibrium, we need to find the negative of the vector sum of F1→ and F2→.

Summing the forces in the x-direction:

F1x = 11 N

F2x = 18 N

F3x = -(F1x + F2x) = -(11 N + 18 N) = -29 N

Summing the forces in the y-direction:

F1y = -5 N

F2y = -2.5 N

F3y = -(F1y + F2y) = -(-5 N + (-2.5 N)) = 7.5 N

To know more about "Force" refer here:

https://brainly.com/question/30751496#

#SPJ11

What is the work done to slow a 1.8 x 10^5 kg train car from 60 m/s to 20 m/s? O-2.9 x 10^8 J O-1.3 x 10^3 J O 3.1 x 10^5 J O 6.1 x 10^4 J 2.9 x 10^6 J

Answers

The work done to slow the 1.8 x 10^5 kg train car from 60 m/s to 20 m/s is approximately -2.88 x 10^8 J = -2.9 x 10^8J

The work done to slow down a train car can be calculated using the formula:

Work = (1/2) * mass * (final velocity^2 - initial velocity^2)

Mass of the train car (m) = 1.8 x 10^5 kg

Initial velocity (u) = 60 m/s

Final velocity (v) = 20 m/s

Using the formula, we can calculate the work done:

Work = (1/2) * (1.8 x 10^5 kg) * [(20 m/s)^2 - (60 m/s)^2]

= (1/2) * (1.8 x 10^5 kg) * (400 m^2/s^2 - 3600 m^2/s^2)

= (1/2) * (1.8 x 10^5 kg) * (-3200 m^2/s^2)

= -2.88 x 10^8 J

Therefore, the work done to slow down the train car from 60 m/s to 20 m/s is approximately -2.88 x 10^8 J.

The correct option from the given choices is: O-2.9 x 10^8 J

When the train car slows down, the work done on the car is negative because the force applied is in the opposite direction to the displacement. The work done is equal to the change in kinetic energy of the car. In this case, the initial kinetic energy is higher than the final kinetic energy, hence the negative sign.

The work done to slow the 1.8 x 10^5 kg train car from 60 m/s to 20 m/s is approximately -2.88 x 10^8 J = -2.9 x 10^8J

To know more about work visit:

https://brainly.com/question/28356414

#SPJ11

what is the magnitude of the magnetic field in the shaded region

Answers

The magnitude of the magnetic field in the shaded region is determined as 1.3 T.

What is magnetic field?

A magnetic field is a picture that we use as a tool to describe how the magnetic force is distributed in the space around and within something magnetic.

Also, a magnetic field is a vector field in the neighborhood of a magnet, electric current, or changing electric field in which magnetic forces are observable.

From the given question, if the magnitude of the magnetic field is uniform, then, the value of the magnetic field in the shaded region will remain the same.

The magnitude of the magnetic field in the shaded region is calculated as follows;

B = B₀ x d₀/d₁

where;

B₀ is the initial magnetic fieldd is the distance of the charge

B = 1.3T  x 8 cm / 8 cm

B = 1.3 T

Learn more about magnitude of magnetic field here: https://brainly.com/question/30880745

#SPJ4

Find the rest energy, in terajoules, of a 17.1 g piece of chocolate. 1 TJ is equal to 1012 J .

rest energy:

TJ

Answers

The rest energy of a 17.1 g piece of chocolate is 485.3 terajoules.

According to the formula E = mc², the energy (E) of an object is equal to its mass (m) multiplied by the speed of light (c) squared. The rest energy (E₀) of an object is its energy at rest. The rest energy of a 17.1 g piece of chocolate can be found as follows:

$$E₀ = mc²$$

Where m = 17.1 g = 0.0171 kg and c = speed of light = 2.998 × 10⁸ m/s.

Plugging in these values, we get:

$$E₀ = (0.0171 kg) × (2.998 × 10⁸ m/s)² = 4.853 × 10¹⁴ J$$

To convert joules to terajoules, we divide by 10¹²:

$$E₀ = \frac{4.853 × 10¹⁴ J}{10¹² J/TJ} = 485.3 TJ

More on rest energy: https://brainly.com/question/31796191

#SPJ11

A +13 nC charge is located at the origin.
A)What is the electric field at the position (x1,y1)=(5.0 cm, 0 cm)? Write electric field vector in component form.Enter the x and y components of the electric field separated by a comma. B)What is the electric field at the position (x2,y2)=(-5.0 cm, 5.0 cm)? Write electric field vector in component form.Enter the x and y components of the electric field separated by a comma.

Answers

Therefore, the electric field at the position (5.0 cm, 0 cm) is 1.144 N/C in the x-direction and the electric field at the position (-5.0 cm, 5.0 cm) is 0.468 N/C in both x and y directions.

A +13 nC charge is located at the origin. The expression to find the electric field at a given position is

E=KQ / r²,

where K is Coulomb's constant, Q is the charge and r is the distance between the charge and the point where we want to find the electric field.

So, A) The position at which electric field is to be calculated is

(x1,y1)= (5.0 cm, 0 cm).

Hence, distance

r = [tex]\sqrt{((5.0 cm)^{2} + (0 cm)^{2})}[/tex]

= 5.0 cm (as the point lies on x-axis).

Now, Electric field vector E = KQ / r²

= [tex]9 *10^{9} N.m² / C² * 13 * 10{-9}C / (5.0 * 10{-2} m)^{2}[/tex]

= 1.144 N/C

In component form, E = Exi + Eyj, where i and j are the unit vectors in the x and y directions respectively.

Therefore, E = Exi

= 1.144 N/C (as the electric field is only in the x-direction and there is no component of electric field in the y-direction)Hence, the main answer is: 1.144, 0

Electric field vector E = KQ / r²

= [tex]9 *10^{9} N.m² / C² * 13 * 10{-9}C / (5.0 * 10{-2} m)^{2}[/tex]

= 1.144 N/C

In component form, E = Exi + Eyj, where i and j are the unit vectors in the x and y directions respectively. Therefore,

E = Exi = 1.144 N/C (as the electric field is only in the x-direction and there is no component of electric field in the y-direction)B) The position at which electric field is to be calculated is (x2,y2)=(-5.0 cm, 5.0 cm).

Hence, distance

r = [tex]\sqrt{((-5.0 cm)^{2}+ (5.0 cm)^{2})}

= 7.07 cm.

Now, Electric field vector

E = KQ / r²

= [tex]9 *10^{9} N.m² / C² * 13 * 10{-9}C / (7.07 * 10{-2} m)^{2}[/tex]

= 0.659 N/C

In component form, E = Exi + Eyj, where i and j are the unit vectors in the x and y directions respectively.

Therefore, E = 0.468i + 0.468j (as the electric field makes an angle of 45° with both the x-axis and y-axis) answer is: 0.468

Therefore, the electric field at the position (5.0 cm, 0 cm) is 1.144 N/C in the x-direction and the electric field at the position (-5.0 cm, 5.0 cm) is 0.468 N/C in both x and y directions.

For more information on electric field  kindly visit to

https://brainly.com/question/14300841

#SPJ11

A(n) asymmetric encryption algorithm requires the use of a secret key known to both the sender and receiver.
True/False

Answers

Statement : A(n) asymmetric encryption algorithm requires the use of a secret key known to both the sender and receiver, is False.

In asymmetric encryption, also known as public-key encryption, there are two different keys: a public key and a private key. The public key is available to anyone and is used for encryption, while the private key is kept secret and is used for decryption. The sender uses the recipient's public key to encrypt the message, and the recipient uses their private key to decrypt it.
Asymmetric encryption does not require the use of a shared secret key between the sender and receiver. It relies on the use of different key pairs, where the public key can be freely shared while the private key remains confidential. This property makes asymmetric encryption more secure and suitable for various applications such as secure communication and digital signatures.

To know more about , asymmetric encryption algorithm, click here https://brainly.com/question/29217765

#SPJ11

A 6.70-C charge of mass 4.10 x 10-12 kg is moving with a speed of 1.60 x 105 m/s in a 0.400-T uniform magnetic field. Y Part A - Determine the magnitude of the magnetic force on the charge if it is mo

Answers

The magnitude of the magnetic force on the charge is 4.97 x 10^-4 N. This calculation is based on the charge of 6.70 C, the velocity of 1.60 x 10^5 m/s, and the magnetic field of 0.400 T.

The magnetic force on a charged particle moving in a magnetic field can be calculated using the equation:

Force = Charge × Velocity × Magnetic Field

Given that the charge is 6.70 C, the velocity is 1.60 x 10^5 m/s, and the magnetic field is 0.400 T, we can calculate the magnitude of the magnetic force:

Force = (6.70 C) × (1.60 x 10^5 m/s) × (0.400 T)

= 4.97 x 10^-4 N

The magnetic force is perpendicular to both the velocity of the charge and the magnetic field direction, following the right-hand rule.

The magnitude of the magnetic force on the charge is 4.97 x 10^-4 N. This calculation is based on the charge of 6.70 C, the velocity of 1.60 x 10^5 m/s, and the magnetic field of 0.400 T. The force is determined using the equation that relates charge, velocity, and magnetic field strength. The magnetic force acts perpendicular to both the velocity of the charge and the direction of the magnetic field.

To know more about magnetic visit:

https://brainly.com/question/26257705

#SPJ11

Other Questions
Question 13 3 pts We need 300 units of Item X. If 100 are already in stock, then the gross requirement is and the net requirement is O 350, 250 O 350, 300 O 300, 250 O 300, 200 You must complete the following tasks:1. Using the KNIME platform examine Summary Statistics2. Build Decision Tree, Logistic Regression and KNN workflows in KNIME3. Create a validation set: Split your dataset into two parts, "Train" and "Test".4. Train and build Classification models for your dataset5. Evaluate and compare the Performance of your Models using the ConfusionMatrix and Determine Accuracy RateWhen you have completed tasks 1-5 above, you Find the average rate of change of the function f ( x ) = 9 3 x - 1 , on the interval x [-1,5]. Average rate of change = Give an exact answer. Rue's utility function is U(x,y) = min{2, 3y). Jules' utility function is U(t,y) min{I, VT} 4 (a) Which of the bundles A = (4, 0.5), B = (3, 2) and C = (2, 4) does Rue prefer? Which of the bundles does Jules prefer? (b) For Rue, draw the indifference curve, denoted as I, that contains the bundles that she likes exactly as well as bundle (4,2). On the same graph, draw the indifference curve I, for Rue that passes through bundle (6,3) and draw the indifference curve Is for Rue that passes through bundle (8,3). Does her preference satisfy convexity? 2.a) Explain the quantity theory of money.b) What are the basic assumptions behind the quantity theory of money?c) If money supply (M) rises by10% and real output or RGDP (Y) rises by 5%, what would be the % change in prices (P) assuming the velocity of circulation of money (V) remains constant.3. a) If the Fed wants to lower countrys money supply (M), will it buy bonds or sell bonds? b) Suppose the Fed wants to reduce countrys money supply by $500 billion by doing open market operations. How much bonds the Fed would have to buy or sell if the required reserve ratio is 10%? Which of the following bonds would most likely sell at the highest yield? O a puttable debenture O a callable debenture O a puttable mortgage bond O a callable mortgage bond ____ happens when actively developing cortical regions grow outward over an adjacent and slowly developing, or nonexpanding, region (such as the insula). U Question 16 0.1 pts For testing of knowledge, the use of speed tests is Critical to effective testing, Never of any value Calculated for multiple-choice tests by multiplying the number of questions by 25, which will give you the length of time in minutes. None of these is correct. Please fill the spaces of the questionCarpentry and Painting Hours Carpentry 0.5 Flats Hanging Drops 2.0 Props 3.0 Print Done Painting 2.0 13.0 4.0 I XA community playhouse needs to determine the lowest-cost production budget for an upc jenna is redoing her bathroom floor with tiles measuring 6 in. by 14 in. the floor has an area of 8,900 in2. what is the least number of tiles she will need? the inclusion of nurses in the systems development life cycle Case Study ProjectThere are many students enrolled in the management information systems major, some of whom have completed the number of this year and some are about to graduate. We have the student Ahmed, who is one of the students who completed 90 hours at the university and his average is 4.25 out of 5. He has a desire to join one of the leading companies in the field of petroleum or the field of Telecommunications or technology and technology. Ahmed obtained high grades in the subjects of the specialization, and he is academically and academically superior to some extent, and he is an ambitious person, but he does not have good knowledge of how to enter the labor market, and he lacks good experienceRequired3) What professional courses should he take? What is the strategy and plan that he should follow in order to obtain it before graduating?4) What are the most important aspects that he should take into account before entering the labor market? What are the problems and obstacles that can be encountered? And what are the solutions? Chi Square Crash Course Quiz Part A: We conduct a similar studyusing the same two groups we used for the t-Test. Recallthat in this clothing study, the boys were randomly assigned towear either supYou get the following data: I Clothing Condition (1= Superhero, 2= Street Clothes) When do superheroes work harder? Crosstabulation When do superheroes work harder? in their street clothes Total Count Consider the following games. In each case, (i.) identify which player canbenefit from making a strategic move, (ii) identify the nature of the strategicmove appropriate for this purpose, (iii) discuss the conceptual and practicaldifficulties that will arise in the process of making this move credible, and(iv) discuss whether and how the difficulties can be overcome.a) The other countries of the European Monetary Union (France, Germany,and so on) would like Britain to join the common currency andthe common central bank.(b) The United States would like North Korea to stop exporting missiles andmissile technology to countries such as Iran and would like China tojoin the United States in working toward this aim.(c) The United Auto Workers would like U.S. auto manufacturers not tobuild plants in Mexico and would like the U.S. government to restrictimports of autos made abroad.(d) The students at your university or college want to prevent the administration from raising tuition.(e) Most participants, as well as outsiders, want to achieve a durable peacein Afghanistan, Iraq, Israel, and Palestine.(f) Nearly all nations of the world want Iran to shut down its nuclear program. If a female indentured servant became pregnant while still under servitude, the master typicallyQuestion 26 options:extended her term by two years.fired her immediately. xsold her contract to the highest bidder xdid nothing, because pregnancy was considered an inevitable part of life. x Suppose the real risk-free rate is 4.20%, the average expected future inflation rate is 4.40%, and a maturity risk premium is MRP = 0.043%(t-1), where t is the number of years to maturity. What rate of return would you expect on a 4-year Treasury security?Group of answer choices9.00%8.46%7.65%9.72%8.73% Which of the following appears to be the only effective treatment for chronic gender dysphoria in adults? Antidepressant medication Sex reassignment surgery Masturbatory retraining Systematic desensitization The Division of Partnership Net Income is a method of calculating how much earnings are attributable to each partner. The calculations 4 Multiple Choice may include Interest Allowances minus Selery Allowances may include Salary Allowances and Drawings may result in the grand total of all partners shares equal to an amount larger than the original Net Income for the year may result in Residual Losses even if the company made a profit for the year When COVID-19 started spreading across the world, the race was on to develop vaccines as quickly as possible. Such research & development has a high fixed cost and can only be undertaken in industries with high market concentration where firms have significant monopoly power, like the pharmaceutical industry. Examine this industry using the theory and models of market (or industry) structure. Should government be worried about any aspect of how an industry with this market structure will perform Consider a consumer choice model with two goods, X and Y. The consumer thinks X and Y are perfect substitutes. At the initial choice, the consumer only buys X. When the price of X increases, the consumer only buys Y. Then this price change has only one effect: the substitution effect.TrueFalse