Water at 70 kPa and 100°C is compressed isentropically in a closed system to 4 MPa. Determine the final temperature of the water and the work required, in kJ/kg, for this compression. [Ans.: 664°C, 887.1 kJ/kg]

Answers

Answer 1

Final temperature of water is 664°C and work required for the compression process is 887.1 kJ/kg.

Given data:

Initial pressure P1 = 70 kPa

Initial temperature T1 = 100°C

Final pressure P2 = 4 MPa

Adiabatic or isentropic process, so heat transferred is zero, Q = 0

We need to determine the final temperature T2 and the work required for the compression process, W.

Adiabatic process is a process where there is no heat transfer, Q = 0. The energy balance equation for a closed system undergoing adiabatic or isentropic process can be written as:

dE = dQ - dW

Here, dE = Change in internal energy

dQ = Heat transferred (for adiabatic process, dQ = 0)

dW = Work done by the system

We can write the above equation in terms of specific quantities as: de = dq - dw

where, e = Internal energy per unit mass

q = Heat transferred per unit mass (for adiabatic process, q = 0)w = Work done per unit mass

We can use the entropy formula to determine the final temperature T2.S = constant

We can use the following equation for an adiabatic process:

S1 = S2

where S1 is the entropy of the water at P1 and T1 and S2 is the entropy of the water at P2 and T2.

S2 = S1 = constant

The entropy of the water can be calculated using the following equation:

s = Cp ln(T) - R ln(P)

where, s is the entropy per unit mass, Cp is the specific heat capacity at constant pressure, R is the gas constant, P is the pressure, and T is the temperature.

In our case, since the process is isentropic or adiabatic, the entropy change is zero.

Therefore, we can write:

S2 - S1 = 0Cp ln(T2) - R ln(P2) - Cp ln(T1) + R ln(P1) = 0Cp ln(T2/T1) - R ln(P2/P1) = 0Cp ln(T2/T1) = R ln(P1/P2)T2/T1 = (P1/P2)^(R/Cp)T2 = T1 * (P1/P2)^(R/Cp)

The specific heat capacity at constant pressure for water vapor can be taken as Cp = 1.872 kJ/kg K and the gas constant for water vapor is R = 0.4615 kJ/kg K.

The work done for an adiabatic process can be calculated using the following equation:

W = Cp * (T1 - T2)/(γ - 1)

where γ = Cp/Cv is the ratio of specific heats.

Cv for water vapor can be taken as 1.4 kJ/kg K.The specific work done per unit mass for the compression process can be calculated as:

W/m = W/m = Cp * (T1 - T2)/(γ - 1)We can substitute the given values in the above equations to obtain:

T2 = T1 * (P1/P2)^(R/Cp)T2 = 100 + 273.15 * (70 / 4000)^(0.4615/1.872) = 937.15

K = 664°CW/m = Cp * (T1 - T2)/(γ - 1)W/m = 1.872 * (100 + 273.15 - 937.15)/(1.4 - 1) = -887.1 kJ/kg

Work required for the compression process is 887.1 kJ/kg.

Final temperature of water is 664°C and work required for the compression process is 887.1 kJ/kg.

To know more about work, visit:

https://brainly.com/question/18094932

#SPJ11


Related Questions

a child on a merry-go-round takes 4.4 s to go around once. what is his angular displacement during a 1.0 s time interval?

Answers

The child's angular displacement during a 1.0 s time interval is approximately 1.432 radians.

To determine the angular displacement of the child on the merry-go-round during a 1.0 s time interval, we can use the formula:

Angular Displacement (θ) = Angular Velocity (ω) × Time (t)

The angular velocity (ω) can be calculated by dividing the total angular displacement by the total time taken to complete one revolution.

In this case:

Time taken to go around once (T) = 4.4 s

Angular Velocity (ω) = 2π / T

Angular Velocity (ω) = 2π / 4.4 s ≈ 1.432 radians/s

Now, we can calculate the angular displacement during a 1.0 s time interval:

Angular Displacement (θ) = Angular Velocity (ω) × Time (t)

Angular Displacement (θ) = 1.432 radians/s × 1.0 s

Angular Displacement (θ) ≈ 1.432 radians

Learn more about angular displacement here:

https://brainly.com/question/31387317

#SPJ11

The angular displacement of the child during a 1.0 s time interval is 1.44 radian. The given values are, Time taken by the child to go around once, t = 4.4 s Time interval, t₁ = 1 s

Formula used: Angular displacement (θ) = (2π/t) × t₁. Substitute the given values in the formula, Angular displacement (θ) = (2π/t) × t₁= (2π/4.4) × 1= 1.44 radian. Thus, the angular displacement of the child during a 1.0 s time interval is 1.44 radian.

The change in the angular position of an object or a point in a rotational system is known as angular displacement and it measures the amount and direction of rotation from an initial position to a final position. Angular displacement is an important concept in physics and engineering, as it helps to describe a rotational motion.

To know more about angular displacement, refer

https://brainly.com/question/31150979

#SPJ11

if a dvd is spinning at 100 mph and has a radius of 14 inches, what is the linear speed of a point 3 inches from the center.

Answers

The linear speed of a point 3 inches from the center of a DVD spinning at 100 mph and with a radius of 14 inches is approximately 219.91 mph.

Linear speed is the rate at which an object moves along a circular path. It is measured in distance per unit time, such as miles per hour (mph) or meters per second (m/s).

The formula for linear speed is:

v = rω where:

v = linear speed

r = radius of the circle

rω = angular speed (measured in radians per second)

To calculate the linear speed of a point on a DVD spinning at 100 mph and with a radius of 14 inches, we need to convert the units of the given speed from mph to inches per second:

100 mph = (100 x 5280 feet) / 3600 seconds = 146.67 feet/second

146.67 feet/second = 1760 inches/second

Next, we need to find the angular speed ω of the DVD.

Angular speed is the rate at which an object rotates about an axis, and it is measured in radians per second. The formula for angular speed is:

ω = 2πf where:

ω = angular speed

f = frequency (measured in hertz)

π = 3.14159...

The frequency f of the DVD is equal to its rotational speed divided by the number of revolutions per second. One revolution is a complete turn around the circle, or 2π radians. Therefore, the frequency is:

f = (100 mph) / (2π x 14 inches x 3600 seconds/5280 feet) = 0.862 hertz

Finally, we can substitute the given values into the formula for linear speed:

v = rωv = (14 + 3) inches x 2π x 0.862 hertz = 219.91 inches/second

Therefore, the linear speed of a point 3 inches from the center of a DVD spinning at 100 mph and with a radius of 14 inches is approximately 219.91 mph.

Learn more about Linear speed https://brainly.com/question/29345009

#SPJ11

Question 1 Calculate the amount of radiation emitted by a blackbody with a temperature of 353 K. Round to the nearest whole number (e.g., no decimals) and input a number only, the next question asks a

Answers

The amount of radiation emitted by a blackbody with a temperature of 353 K is 961 {W/m}².

The formula for calculating the amount of radiation emitted by a blackbody is given by the Stefan-Boltzmann law: j^* = \sigma T^4 Where j* is the radiation energy density (in watts per square meter), σ is the Stefan-Boltzmann constant (σ = 5.67 x 10^-8 W/m^2K^4), and T is the absolute temperature in Kelvin (K).Using the given temperature of T = 353 K and the formula above, we can calculate the amount of radiation emitted by the blackbody: j^* = \sigma T^4 j^* = (5.67 \times 10^{-8}) (353)^4 j^* = 961.2 {W/m}².

Therefore, the amount of radiation emitted by the blackbody with a temperature of 353 K is approximately 961 watts per square meter (W/m²).Rounding this to the nearest whole number as specified in the question gives us the final answer of: 961 (no decimals).

More on radiation: https://brainly.com/question/31106159

#SPJ11

21.42 using cyclopentanone as your starting material and using any other reagents of your choice, propose an efficient synthesis for each of the following compounds

Answers

Cyclopentanone, C5H8O is a cyclic ketone and can be converted to various organic compounds with the help of different reagents. Thus, cyclopentanone can be used as a starting material to synthesize different organic compounds using various reagents and catalysts.

Here, efficient syntheses for three organic compounds using cyclopentanone as a starting material are given below:

1) 2-Methylcyclopentanone: It can be prepared by the reaction of cyclopentanone with isopropyl, magnesium bromide, followed by hydrolysis of the resulting product. This reaction is shown below:

2) Cyclopentylmethanol: It can be prepared by the reduction of cyclopentanone with sodium borohydride (NaBH4) in methanol. This reaction is shown below:

3) 2-Cyclopenten-1-one: It can be prepared by the dehydration of cyclopentanol, which can be prepared by the reduction of cyclopentanone with lithium aluminum hydride (LiAlH4). The dehydration of cyclopentanol can be carried out by the elimination of water molecule using an acid catalyst like H2SO4. The overall reaction is shown below.

to know more about cyclopentanone visit:

https://brainly.com/question/14919939

#SPJ11

A 0.200-kg object is attached to a spring that has a force constant of 95.0 N/m. The object is pulled 7.00 cm to the right of equilibrium and released from rest to slide on a horizontal, frictionless table. Calculate the maximum speed Umas of the object. Upis m/y Find the location x of the object relative to equilibrium when it has one-third of the maximum speed, is moving to the right, and is speeding up. m

Answers

The maximum speed of the object is Umas =  1.516 m/s. The location of the object relative to equilibrium when it has one-third of the maximum speed, is moving to the right, and is speeding up is x =  6.97 cm..

To find the maximum speed of the object, we can use the concept of mechanical energy conservation. At the maximum speed, all the potential energy stored in the spring is converted into kinetic energy.

The potential energy stored in the spring is given by:

Potential energy (PE) = (1/2)kx²

Where:

k = force constant of the spring = 95.0 N/m

x = displacement of the object from equilibrium = 7.00 cm = 0.0700 m (converted to meters)

Substituting the values into the equation:

PE = (1/2)(95.0 N/m)(0.0700 m)²

PE ≈ 0.230 Joules

At the maximum speed, all the potential energy is converted into kinetic energy:

Kinetic energy (KE) = 0.230 Joules

The kinetic energy is given by:

KE = (1/2)mv²

Where:

m = mass of the object = 0.200 kg

v = maximum speed of the object (Umas)

Substituting the values into the equation:

0.230 Joules = (1/2)(0.200 kg)v²

v² = (0.230 Joules) * (2/0.200 kg)

v² = 2.30 Joules/kg

v ≈ 1.516 m/s

Therefore, the maximum speed of the object is Umas ≈ 1.516 m/s.

To find the location of the object relative to equilibrium when it has one-third of the maximum speed, we can use the concept of energy conservation again. At this point, the kinetic energy is one-third of the maximum kinetic energy.

KE = (1/2)mv²

(1/3)KE = (1/6)mv²

Substituting the values into the equation:

(1/3)(0.230 Joules) = (1/6)(0.200 kg)v²

0.077 Joules = (0.0333 kg)v²

v² = 2.311 Joules/kg

v ≈ 1.519 m/s

Now, we need to find the displacement x of the object from equilibrium at this velocity. We can use the formula for the potential energy stored in the spring:

PE = (1/2)kx²

Rearranging the equation:

x² = (2PE) / k

x² = (2 * 0.230 Joules) / 95.0 N/m

x² ≈ 0.004842 m²

x ≈ ±0.0697 m

Since the object is moving to the right, the displacement x will be positive:

x ≈ 0.0697 m

Converting this to centimeters:

x ≈ 6.97 cm

Therefore, the location of the object relative to equilibrium when it has one-third of the maximum speed, is moving to the right, and is speeding up is x ≈ 6.97 cm.

The maximum speed of the object is Umas ≈ 1.516 m/s. The location of the object relative to equilibrium when it has one-third of the maximum speed, is moving to the right, and is speeding up is x ≈ 6.97 cm.

To know more about speed, visit:

https://brainly.com/question/30249508

#SPJ11

what is the best definition of relativistic thought according to perry

Answers

Relativistic thought refers to the recognition that our perceptions and beliefs are influenced by our experiences, upbringing, and cultural and social environments, according to Perry.

It suggests that reality is subjectively constructed rather than objectively discovered, and that what is "true" or "right" for one person or group may not be for another. Relativistic thinking entails a degree of tolerance for opposing viewpoints and a willingness to engage in dialogue rather than debate or dismiss opposing perspectives. Instead of seeing things in black and white, relativistic thought acknowledges the nuances and complexity of human experience and acknowledges that there may be multiple valid perspectives on any given issue.

To know more about degree of tolerance, visit:

https://brainly.com/question/32378860

#SPJ11

A 20.0-kg cannon ball is fired from a cannon with a muzzle speed of 100 m/s at an angle of 20.0° with the horizontal. Use the conservation of energy principle to find the maximum height reached by ba

Answers

A 20.0 kg cannonball is fired from a cannon with a muzzle speed of 100 m/s at an angle of 20.0°. Using conservation of energy, the maximum height reached by the cannonball is approximately 510.2 meters.

A cannon ball weighing 20.0 kg is launched from a cannon with an initial velocity of 100 m/s at an angle of 20.0° above the horizontal.

To determine the maximum height reached by the cannonball using the conservation of energy principle, we consider the conversion of kinetic energy into gravitational potential energy.

Initially, the cannonball has only kinetic energy, given by the equation KE = (1/2)mv², where m is the mass and v is the velocity.

At the highest point of its trajectory, the cannonball has no vertical velocity, meaning it has no kinetic energy but possesses gravitational potential energy, given by the equation PE = mgh, where h is the height and g is the acceleration due to gravity (approximately 9.8 m/s²).

Using the conservation of energy, we equate the initial kinetic energy to the maximum potential energy:

(1/2)mv² = mgh

Canceling the mass and rearranging the equation, we find:

v²/2g = h

Plugging in the given values, we have:

(100²)/(2*9.8) = h

Simplifying the equation, we find:

h ≈ 510.2 m

Therefore, the maximum height reached by the cannonball is approximately 510.2 meters.

To know more about maximum height refer here:

https://brainly.com/question/30878848#

#SPJ11

A capacitor is discharged through a 20.0 Ω resistor. The discharge current decreases to 22.0% of its initial value in 1.50 ms.
What is the time constant (in ms) of the RC circuit?
a) 0.33 ms
b) 0.67 ms
c) 1.50 ms
d) 3.75 ms

Answers

The time constant (in ms) of the RC circuit is 3.75 ms. Hence, the correct option is  (d) 3.75 ms.


The rate of decay of the current in a charging capacitor is proportional to the current in the circuit at that time. Therefore, it takes longer for a larger current to decay than for a smaller current to decay in a charging capacitor.A capacitor is discharged through a 20.0 Ω resistor.

The discharge current decreases to 22.0% of its initial value in 1.50 ms. We can obtain the time constant of the RC circuit using the following formula:$$I=I_{o} e^{-t / \tau}$$Where, I = instantaneous current Io = initial current t = time constant R = resistance of the circuit C = capacitance of the circuit

To know more about circuit visit:-

https://brainly.com/question/12608516

#SPJ11

The time constant of the RC circuit is approximately 0.674 m s.

To determine the time constant (τ) of an RC circuit, we can use the formula:

τ = RC

Given that the discharge current decreases to 22.0% of its initial value in 1.50 m s, we can calculate the time constant as follows:

The percentage of the initial current remaining after time t is given by the equation:

I(t) =[tex]I_oe^{(-t/\tau)[/tex]

Where:

I(t) = current at time t

I₀ = initial current

e = Euler's number (approximately 2.71828)

t = time

τ = time constant

We are given that the discharge current decreases to 22.0% of its initial value. Therefore, we can set up the following equation:

0.22 =[tex]e^{(-1.50/\tau)[/tex]

To solve for τ, we can take the natural logarithm (ln) of both sides:

ln(0.22) = [tex]\frac{-1.50}{\tau}[/tex]

Rearranging the equation to solve for τ:

τ = [tex]\frac{-1.50 }{ ln(0.22)}[/tex]

Calculating this expression:

τ ≈ 0.674 m s

Learn more about time constant here:

brainly.com/question/32577767

#SPJ11

Other Questions
You measure 49 turtles' weights, and find they have a mean weight of 68 ounces. Assume the population standard deviation is 4.3 ounces. Based on this, what is the maximal margin of error associated with a 90% confidence interval for the true population mean turtle weight.Give your answer as a decimal, to two places Pam purchased video cameras for all of her employees so they can participate in videoconferencing discussion forum a webinar a screen-sharing application the same computer The audit of which of the following balance sheet accounts does not normally result in verification of an income statement account?A) Cash.B) Accounts receivable.C) Property, plant, and equipment.D) Intangible assets. An investor buys a property for $608,000 with a 25-year mortgage, 8.10% APR, and monthly payments of $4,733. After 75 months (which means she made 75 payments), the investor wants to resell the property. What is the minimum price for which she can sell the property so that she can cover the remaining balance on the mortgage? Current multifactor productivity for 640 work hours per month= loaves/dollar (round your response to three decimal places) = After increasing the number of work hours to 992 per month, the multifactor productivity loaves/dollar (round your response to three decimal places) The percentage increase in productivity=% (enter your response as a percentage rounded to two decimal places). Charles Lackey operates a bakery in Idaho Falls, idaho. Because of its excellent product and excellent location, demand has increased by 55% in the last year. On far too many occasions, customers have not been able to p their choice. Because of the size of the store, no new ovens can be added. At a staff meeting, one employee suggested ways to load the ovens differently so that more loaves of bread can be baked at one time. This new pro the ovens be loaded by hand, requiring additional manpower. This is the only production change that will be made in order to meet the increased demand. The bakery currently makes 1,500 loaves per month. Employees ar addition to the labor cost, Charles also has a constant utility cost per month of $800 and a per loaf ingredient cost of $0.50. se of its excellent product and excellent location, demand has increased by 55% in the last year. On far too many occasions, customers have not been able to purchase the bread of be added. At a staff meeting, one employee suggested ways to load the ovens differently so that more loaves of bread can be baked at one time. This new process will require that mis is the only production change that will be made in order to meet the increased demand. The bakery currently makes 1,800 loaves per month. Employees are paid $8 per hour. In per month of $800 and a per loaf ingredient cost of $0.50. Given f(x)=x^2-6x+8 and g(x)=x^2-x-12, find the y intercept of (g/f)(x)a. 0b. -2/3c. -3/2d. -1/2 A box with a mass of 25 kg rests on a horizontal surface. The coefficient of static friction between the box and the surface is 0.20. What horizontal force must be applied to the box for it to start s given the equation 4x^2 8x + 20 = 0, what are the values of h and k when the equation is written in vertex form a(x h)^2 + k = 0? a. h = 4, k = 16 b. h = 4, k = 1 c. h = 1, k = 24 d. h = 1, k = 16 3. Calculating the mean when adding or subtracting a constant A professor gives a statistics exam. The exam has 50 possible points. The s 42 40 38 26 42 46 42 50 44 Calculate the sample size, n, and t (1 point) let f and g be functions such that f(0)=2,g(0)=5, f(0)=9,g(0)=8. find h(0) for the function h(x)=g(x)f(x). While abusers use a wide variety of instruments to assault children, the two most common aretheA) belt and electric cord.B) hairbrush and clothes hanger. compare and contrast osmoregulation in marine and freshwater fish the rights given to persons over the creations of their minds. they usually give the creator an exclusive right over the use of his/her creation for a certain period of time. Diamond Foods Payments to Nut GrowersThe leadership of Diamond Foods (DF), the global California-based premium snack food company, was excited. In the fall of 2011, the company was close to finalizing an agreement with Proctor & Gamble to acquire Pringles brand in exchange for DF stock, this acquisition would help the company achieve the number two position in the U.S. snack foods industry behind PepsiCo. DF product lines currently included potatoes chips (Kettle), popcorn (Pop-Secret), and (nuts) snack nuts, in-shell nuts and culinary nuts) Emerald and Diamond of California). DF started in 1912 as a grower-owned cooperative called Diamond of California. The company originally focused on walnuts, but more recently they transformed into a diverse snack food company. The business changed from a co-operative business status and went public in 2005 with the NASDAQ ticker DMND. The stock price increased, and in September 2011, the price was at an all-time high of $92 per share.The person who orchestrated the companys expansion and growth was CEO and President Michael Mendes, who was hired in 1997. He had previously worked at Hormel Foods Corporation and Dole Food Company. Mendez was very competitive and implemented the companywide philosophy of "bigger is better". This viewpoint was the corporate culture, and it had a significant impact on employees of DF. This aggressive company culture resulted in an emphasis on financial performance and some bold and very expensive acquisitions (e.g., Kettle and Pop-Secret). The most expensive acquisition was to be Pringles. DF was making this acquisition, so it could be a significant player in the very competitive snack foods space where it felt pressure for financial success and greater market share amid increasing industry competition.In Fall of 2011, Mark Roberts, founder of the Off-Wall Street Consulting Group, received an anonymous call. For the fiscal year ending in July 2011, the caller indicated that DF was making momentum payments to growers for walnuts delivered in September 2011. It appears that the approximately $60 million payments could be impacting the wrong fiscal year financial statements. Robert accused DF of incorrectly reporting its payments to suppliers on the company financial statements. DF denied any illegal actions, and they replied that the payments were on advance on the fiscal 2012 crop and had nothing to do with fiscal 2011. Unfortunately, the nut growers disagreed. They were told by the company to keep the money even if they were not going to provide crops for 2012. Supposedly, they were told that the payments were for the prior year.Investigation into the situation ascertained that an additional approximately $20 million of continuity payments were made by DF growers in fall 2010. Again, the question arose as to what fiscal year did these payments relate. Were the payments recorded in the proper year? Were the books cooked? Would the Pringles acquisition occur?There are many accounting rules that may apply in this case. Discuss the rules that you believe may apply.In what fiscal periods should fall 2010 and fall 2011 payments have been recorded in the DF income statements?When was the cash paid to the growers? Was it a different period than when the payments were recorded?How were the financial statements impacted in 2010 and 2011?2. Were there any other things happening in the company that could have had a part in this?3. How was this case of fraud found? Who found it? What are some steps that could have been taken that may have prevented this? What changes did this company make in order to prevent this from occurring again?4. In the end, was the Pringles line acquired? More spacious office at your new job rms produce potatoes and fish, and households buy potatoes and fish. The accompanying table ows the maximum annual output combinations of potatoes and fish that can be produced. Obviously, given their limited resources and available technology. as they use more of their sources for potato production, there are fewer resources available for catching fish. Maximum annual output options 4 A F Quantity of potatoes (pounds) 1,000 800 600 400 200 0 Quantity of fish (pounds) 0 300 500 600 650 675 Draw a production possibility frontier with potatoes on the horizontal axis and fish on the vertical axis illustrating these options, showing points A-F. I. If Winterfell produces no fish, what is the maximum potato production? II. Can Winterfell produce 500 pounds of fish and 800 pounds of potatoes? Explain. Where would this point lie relative to the production possibility frontier? Is this point efficient? TV. Suppose Winterfell is producing 200 potatoes and 200 fishes. Is this an efficient point? How many additional fish could they produce without giving up any potatoes? V. What is the opportunity cost of increasing the annual output of potatoes from 600 to 800 pounds? VI. What is the opportunity cost of increasing the annual output of potatoes from 200 to 400 pounds? VII. Can you infer about the shape of the PPF? (Hint: Find the per unit opportunity cost of Potatoes relative to fish/ Per unit opportunity cost of fish relative to potatoes) Explain what will happen to PPF in the following situations: VIII. IX. Following a period of discrimination against women and minorities, Winterfell legally ended such discrimination in the work place. X. Before the Battle of Winterfell, Winterfell was a full-employment of their resources, but during the war many of their facilities were bombed and people were killed. 5) The demand supply schedule (consider 52 weeks in a year) Price per bag 5 11) VD 6 DO C 8 10 for small bangs of potato chips in millions of bags per year is: Quantity supplied 70 90 Quantity demanded 160 150 140 130 120 110 110 130 150 170 What is the equilibrium price and quantity per week? How much excess demand or supply exists at a price 6 taka per bag? How much excess demand or supply exists at a price 10 taka per bag? Northeastern Heath is a regional medical center. They tle pricing of services and profits to specific services in the medical center Northeastern Health Usos control system Multiple Choice Conce dan feedforward 1. (a) In reaching equilibrium, how much heat transfer occurs from 1.1 kg of water at 40C when it is placed in contact with 1.1 kg of 20C water? Specific heat of water c=4186 J/(kgC) Hint: If th marta tried solve the system below, but she made a mistake. read carefully and try to figure out what her mistake was. the heat of fusion of water is 79.5 cal/g. this means 79.5 cal of energy are required to: Find the measure(s) of angle given that (cos-1)(sin+1)= 0,and 02. Give exact answers and show all of your work.